DELINEATION OF DEFECTS IN SIMOX STRUCTURES USING A CHEMICAL ETCHING TECHNIQUE

Residual defects in the overlayer of fully annealed SIMOX material have been studied by means of a chemical etching technique. The etching procedure has been calibrated and an optimum recipe is reported. Observations using optical microscopy and transmission electron microscopy have been used to quantify the defect densities and good agreement between the two techniques has been established, confirming that the optimised chemical etching process can be used with confidence to determine the dislocation density for values < 10(7) cm-2.

METASTABLE DEFECT IN AMORPHOUS-SILICON SOLAR-CELLS INVESTIGATED BY JUNCTION RECOVERY TECHNIQUE

The effect of metastable defects caused by light soaking and carrier injection on the transport of carriers in undoped a-Si:H has been investigated by a junction recovery technique. The experiments show that after light soaking or carrier injection the product of mu-p-tau-p decreases, but no detectable change in the distribution of shallow valence band tail states was found.

Lapping technique of InP single crystal wafer

The wafer processing of Indium Phosphide (InP) is so important that it is getting more and more attentions. Lapping is a basic step just following the ingot cutting. In this paper, the influences of various processing parameters on the lapped wafer quality and lapping rate have been checked, the double-crystal X-ray diffraction results about lapped wafers also were presented here. According to the experimental results, the optimum lapping conditions have been obtained.

ALKALINE POLISHING OF INP USING DOUBLE-POURING TECHNIQUE

于2010-11-17批量导入

A STUDY OF THE COMPOSITION DISTRIBUTION AT THE TI/AL2O3 INTERFACE USING THE MCS(+)-SIMS TECHNIQUE

In this article, the MCs(+)-SIMS technique has been used to characterize Ti/Al2O3 metal/insulator interfaces. Our experiment shows that by detecting MCs(+) secondary ions, the matrix and interface effects are reduced, and good depth profiles have been obtained. The experimental result also shows that with the increase of the annealing temperature (RT, 300 degrees C, 600 degrees C, 850 degrees C), the interface gets broadened gradually, indicating diffusion and reaction take place at the interface, and the interface reaction is enhanced with the increase in annealing temperature. When the temperature increases, the AlCs+ signal forms two plateaus in the Ti layer, indicating Al from the decomposition of Al2O3 diffuses into the Ti layer and exists as two new forms (phases). Also, with the increase of the annealing temperature, oxygen diffuses into the Ti layer gradually, and makes the O signal in the Ti layer increase significantly in the 850 degrees C annealed sample.

A novel noise optimization technique for inductively degenerated CMOS LNA

This paper proposes a novel noise optimization technique. The technique gives analytical formulae for the noise performance of inductively degenerated CMOS low noise amplifier (LNA) circuits with an ideal gate inductor for a fixed bias voltage and nonideal gate inductor for a fixed power dissipation, respectively, by mathematical analysis and reasonable approximation methods. LNA circuits with required noise figure can be designed effectively and rapidly just by using hand calculations of the proposed formulae. We design a 1.8 GHz LNA in a TSMC 0.25 pan CMOS process. The measured results show a noise figure of 1.6 dB with a forward gain of 14.4 dB at a power consumption of 5 mW, demonstrating that the designed LNA circuits can achieve low noise figure levels at low power dissipation.

Fabrication of semiconductor optical amplifiers and a novel gain measuring technique

The design and fabrication of 1550 nm semiconductor optical amplifiers (SOAs) and the characteristics of the fabricated SOA are reported. A novel gain measurement technique based on the integrations of the product of emission spectrum and a phase function over one mode interval is proposed for Fabry-Perot semiconductor lasers.

Bandpass filter by a stretch and double-exposure technique

We fabricated a bandpass filter based on Moire Bragg grating in fiber with a uniform phase mask We employed a stretch and two-exposure technique, in which the fiber was exposed to UV light from a KrF excimer through a phase mask and then the fiber is stretched and given another exposure at the same region. Due to the stretch, the periods of these two grating are slightly different, and there is a transmission between two reflection peaks at the Bragg wavelength of these two gratings.Applying different stretch can control the bandpass width of the filter. We measured the stretch characterization of a uniform Bragg grating and found the Bragg wavelength of the grating shifts linearly with the stretched length.We theoretically analyzed the grating structure and its reflection spectrum. The filter's characteristics can be optimized by choosing appropriate parameters. We will give a theoretical discussion concerning which parameters and how they affect the filter's operation.