1．3μm量子点垂直腔面发射激光器高频响应的优化设计

结合垂直腔面发射激光器（VCSEL）原理以及量子点增益特点，计算了有源层P掺杂结构的量子点VCSEL的材料增益和3dB带宽，发现P掺杂结构可以大大提高频率特性．结合VCSEL激射条件和阈值特性，分析了对VCSEL结构的要求；分析了分布参数对频率特性的影响，对其外部封装提出了要求．设计了高频率响应的含氧化限制层的1．3μm量子点VCSEL结构．

1.3μm InGaAs/InAs/GaAs Self-Assembled Quantum Dot Laser Diode Grown by Molecular Beam Epitaxy

The growth of multi-layer InGaAs/InAs/GaAs self-assembled quantum dots （QDs） by molecular beam epitaxy （MBE） is investigated,and a QD laser diode lasing at 1.33μm in continuous operation mode at room temperature is reported. The full width at half maximum of the band edge emitting peaks of the photoluminescence （PL） spectra at room temperature is less than 35meV for most of the multi-layer QD samples,revealing good,reproducible MBE growth conditions. Moreover,atomic force microscopy images show that the QD surface density can be controlled in the range from 1×10^10 to 7 ×10^10 cm^-2 . The best PL properties are obtained at a QD surface density of about 4×10^10cm^-2. Edge emitting lasers containing 3 and 5 stacked QD layers as the active layer lasing at room temperature in continuous wave operation mode are reported.

1.3-μm uncooled 10 Gb/s directly modulated MQW AlGaInAs/InP laser diodes

In this paper, we report a novel 1.3-μm uncooled AlGaInAs/InP multiple quantum well (MQW) ridge waveguide laser diodes. By optimizing the design of MQW structure and facet coatings, together with the application of reversed-mesa ridge waveguide (RM-RWG) structure, polyimide planarization, and lift-off processes technology, an uncooled 1.3-μm, 10-Gb/s directly modulated MQW ridge waveguide laser diode was successfully fabricated. The threshold current and the slope efficiency were 7 mA and 0.48 mW/mA, respectively. The directly modulated bandwidths of 11 and 9.2 GHz were achieved at room temperature and 80 Celsius degrees, respectively.

1.3μm GaAs基量子点垂直腔面发射激光器结构设计与分析

结合垂直腔面发射激光器(VCSEL)原理以及量子点增益特点,计算了不同结构VCSEL的腔内损耗和量子点的模式增益.分析了激光器阈值特性以及氧化限制层对光损耗的影响.设计了含氧化限制层的1.3 μm量子点VCSEL结构.

Material Growth and Device Fabrication of GaAs Based 1.3μm GaInNAs Quantum Well Laser Diodes

Material growth and device fabrication of the first 1.3μm quantum well （QW） edge emitting laser diodes in China are reported. Through the optimization of the molecular beam epitaxy （MBE） growth conditions and the tuning of the indium and nitrogen composition of the GalnNAs QWs, the emission wavelengths of the QWs can be tuned to 1.3μm. Ridge geometry waveguide laser diodes are fabricated. The lasing wavelength is 1.3μm under continuous current injection at room temperature with threshold current of 1kA/cm^2 for the laser diode structures with the cleaved facet mirrors. The output light power over 30mW is obtained.

Growth of Space Ordered on GaAs（100） Vicinal 1.3μm InAs Quantum Dots Substrates by MOCVD

Space ordered 1.3μm self-assembled InAs QDs are grown on GaAs（100） vicinal substrates by MOCVD. Photoluminescence measurements show that the dots on vicinal substrates have a much higher PL intensity and a narrower FWHM than those of dots on exact substrates, which indicates better material quality. To obtain 1.3μm emissions of InAs QDs, the role of the so called InGaAs strain cap layer （SCL） and the strain buffer layer （SBL） in the strain relaxation process in quantum dots is studied. While the use of SBL results only in a small change of emission wavelength,SCL can extend the QD＇s emission over 1.3μm due to the effective strain reducing effect of SCL.

In0.2 Ga0.8 As-GaAs复合应力缓冲层上的1.3 μmInAs/GaAs自组织量子点

用光荧光谱和原子力显微镜测试技术系统研究了在2 nm In0.2Ga0.8As和x ML GaAs的复合应力缓冲层上生长的InAs/GaAs自组织量子点的发光特性和表面形貌.采用In0.2Ga0.8As与薄层GaAs复合的应力缓冲层,由于减少了晶格失配度致使量子点密度从约1.7×109 cm-2显著增加到约3.8×109cm-2.同时,复合层也有利于提高量子点中In的组份,使量子点的高宽比增加,促进量子点发光峰红移.对于x=10 ML的样品室温下基态发光峰达到1350 nm.

A 1.3μm Low-Threshold Edge-Emitting Laser with AlInAs-Oxide Confinement Layers

A 1.3μm low-threshold edge-emitting AlGaInAs multiple-quantum-well(MQW) laser with AlInAs-oxide confinement layers is fabricated.The Al-contained waveguide layers upper and low the active layers are oxidized as current-confined layers using wet-oxidation technique.This structure provides excellent current and optical confinement,resulting in 12.9mA of a low continuous wave threshold current and 0.47W/A of a high slope efficiency of per facet at room temperature for a 5-μm-wide current aperture.Compared with the ridge waveguide laser with the same-width ridge,the threshold current of the AlInAs-oxide confinement laser has decreased by 31.7% and the slope efficiency has increased a little.Both low threshold and high slope efficiency indicate that lateral current confinement can be realized by oxidizing AlInAs waveguide layers.The full width of half maximum angles of the Al-InAs-oxide confinement laser are 21.6° for the horizontal and 36.1° for the vertical,which demonstrate the ability of the AlInAs oxide in preventing the optical field from spreading laterally.

Surface Morphology and Photoluminescence of 1.3 μm Wavelength In(Ga)As/GaAs Quantum Dots

Self-organized In_(0.5)Ga_(0.5)As/GaAs quantum island structure emitting at 1. 35 (im at room temperature has been successfully fabricated by molecular beam epitaxy (MBE) via cycled (InAs)_1/( GaAs)_1 monolayer deposition method. Photoluminescence (PL) measurement shows that very narrow PL linewidth of 19.2 meV at 300 K has been reached for the first time, indicating effective suppression of inhomogeneous broadening of optical emission from the In_(0.5)Ga_(0.5)As islands structure. Our results provide important information for optimizing the epitaxial structures of 1.3 μm wavelength quantum dot (QD) devices.

1.3μm Si-Based MOEMS Optical Tunable Filter with a Tuning Range of 90nm

Optical filters capable of single control parameter-based wide tuning are implemented and studied. A prototype surface micromachined 1.3μm Si-based MOEMS (micro-opto-electro-mechanical-systems) tunable filter exhibits a continuous and large tuning range of 90 nm at 50 V tuning voltage. The filter can be integrated with Si-based photodetector in a low-cost component for coarse wavelength division multiplexing systems operating in the 1.3μm band.

1.3微米发光自组织InAs/GaAs量子点的电致发光研究

用优化的MBE参数生长了1.3μm发光的InAs/GaAs量子点材料，并制成发光二极管，对不同温度和有源区长度下样品的电致发光谱进行了细致的研究。观察到两个明显的电致发光峰，分别对应于量子点基态和激发态的辐射复合发光。实验表明，由于能态填充效应的影响，适当增大量子点发光器件有源区长度，更有利于获得基态的光发射。这个结果提供了一种控制和调节InAs/GaAs量子点发光二极管和激光器的工作波长的方法。

巨磁电阻材料La_(2/3)Ca_(1/3)Mn(O_(1-x),F_x)_3的研究

主要采用了X射线衍射、Mossbauer谱、磁测量等方法系统研究了块体巨磁电阻材料La_(2/3)Ca_(1/3)Mn_(1-x)Fe_xO_3在不同铁含量(0≤x≤0.84)时结构、性能、磁性的变化，并给予合理的解释。在0

1.3μm低阈值InGaAsP/InP应变补偿MQW激光器的LP-MOCVD生长

报道了用低压金属有机物化学气相淀积(LP-MOCVD)方法外延生长InGaAsP/InP应变补偿多量子阱结构。用此材料制备的掩埋异质结(BH)条形结构多量子阱激光器具有极低阈值电流4～6mA。20～40℃时特征温度T_0高达67K，室温下外量子效率为0.3mW/mA。

低阈值1.3μm InGaAsP/InP应变补偿多量子阱DFB激光器LP-MOCVD生长

报道了用低压－金属有机化学气相淀积(LP-MOCVD)方法制作1.3μm应变补偿多量子阱结构材料。X射线双晶衍射摇摆曲线可清晰地看到±4级卫星峰和卫星峰间的Pendellosong条纹。整个有源区的平均应变量几乎为零。用掩埋异质结(BH)条形工艺制备的含一级光栅的DFB激光器室温下阈值电流2～4mA,外量子效率0.33mW/mA,线性输出光功率达30mW,边模抑制比(SMSR)大于35dB。20～40℃下的特征温度T_0为67K。

1.3μm InGaAsP/InP应变多量子阱部分增益耦合DFB激光器

在国内首次报道了采用直接刻蚀有源区技术在应变多量子阱有源区结构基础上制作了1.3μm InGaAsP/InP部分增益耦合DFB激光器，器件采用全MOVPE生长，阈值电流10mA,边模抑制比(SMSR)大于35dB,在端面未镀膜情况下器件单纵模成品率较高。