Influence of indium-tin-oxide thin-film quality on reverse leakage current of indium-tin-oxide/n-GaN Schottky contacts

Indium-tin-oxide (ITO)/n-GaN Schottky contacts were prepared by e-beam evaporation at 200 degrees C under various partial pressures of oxygen. X-ray photoemission spectroscopy and positron beam measurements were employed to obtain chemical and structural information of the deposited ITO films. The results indicated that the observed variation in the reverse leakage current of the Schottky contact and the optical transmittance of the ITO films were strongly dependent on the quality of the ITO film. The high concentration of point defects at the ITO-GaN interface is suggested to be responsible for the large observed leakage current of the ITO/n-GaN Schottky contacts. (c) 2006 American Institute of Physics.

Electron resonant tunneling through InAs/GaAs quantum dots embedded in a Schottky diode with an AlAs insertion layer

Molecular beam epitaxy was employed to manufacture self-assembled InAs/GaAs quantum dot Schottky resonant tunneling diodes. By virtue of a thin AlAs insertion barrier, the thermal current was effectively reduced and electron resonant tunneling through quantum dots under both forward and reverse biased conditions was observed at relatively high temperature of 77 K. The ground states of quantum dots were found to be at similar to 0.19 eV below the conduction band of GaAs matrix. The theoretical computations were in conformity with experimental data. (c) 2006 The Electrochemical Society.

Thermal annealing behaviour of Pt on n-GaN Schottky contacts

The structural evolution and temperature dependence of the Schottky barrier heights of Pt contacts on n-GaN epilayer at various annealing temperatures were investigated extensively by Rutherford backscattering spectrometry, x-ray diffraction measurements, Auger electron spectroscopy, scanning electron microscopy and current-voltage measurements. The temperature dependence of the Schottky barrier heights may be attributed to changes of surface morphology of Pt films on the surface and variation of nonstoichiometric defects at the interface vicinity. Experimental results indicated the degradation of Pt contacts on n-GaN above 600 degreesC.

Study on the reverse characteristics of Ti/6H-SiC Schottky contacts

The reverse I(V) measurement and analytic calculation of the electron transport across a Ti/6H-SiC Schottky barrier are presented. Based on the consideration of the barrier fluctuations and the barrier height shift caused by image charge and the applied voltage drop across Ti/SiC interfical layer, a comprehensive analytical model for the reverse tunneling current is developed using a WKB calculation of the tunneling probability through a reverse biased Schottky barrier. This model takes into account the main reverse conduction mechanism, such as field emission, thermionic field emission and thermionic emission. The fact that the simulated results are in good agreement with the experimental data indicates that the barrier height shift and barrier fluctuation can lead to reverse current densities orders of magnitude higher than that obtained from a simple theory. It is shown that the field and thermionic field emission processes, in which carries can tunnel through the barrier but cannot surmount it with insufficient thermal energy, dominate the reverse characteristics of a SiC Schottky contacts in a normal working condition.

Thermal annealing behaviour of Ni/Au on n-GaN Schottky contacts

The Schottky behaviour of Ni/Au contact on n-GaN was investigated under various annealing conditions by current-voltage (I-V) measurements. A non-linear fitting method was used to extract the contact parameters from the I-V characteristic curves. Experimental results indicate that high quality Schottky contact with a barrier height and ideality factor of 0.86 +/- 0.02 eV and 1.19 +/- 0.02 eV, respectively, can be obtained under 5 min annealing at 600degreesC in N-2 ambience.

Characterization of deep levels in Pt-GaN Schottky diodes deposited on intermediate-temperature buffer layers

Gallium nitride (GaN)-based Schottky junctions were fabricated by RF-plasma-assisted molecular beam epitaxy (MBE). The GaN epitaxial layers were deposited on novel double buffer layers that consist of a conventional low-temperature buffer layer (LTBL) grown at 500 degreesC and an intermediate-temperature buffer layer (ITBL) deposited at 690 degreesC. Low-frequency excess noise and deep level transient Fourier spectroscopy (DLTFS) were measured from the devices. The results demonstrate a significant reduction in the density of deep levels in the devices fabricated with the GaN films grown with an ITBL. Compared to the control sample, which was grown with just a conventional LTBL, a three-order-of-magnitude reduction in the deep levels 0.4 eV below the conduction band minimum (Ec) is observed in the bulk of the thin films using DLTFS measurements.

Hydrogen sensors based on Pt-AlGaN/GaN back-to-back Schottky diode

In this paper, platinum (Pt) with a thickness of 45 nm was sputtered on the surface of AlGaN/GaN heterostructure to form the Schottky contact and the back-to-back Schottky diodes were characterized for H-2 sensing at room temperature. Both the forward and reverse current of the devices increased with exposure to H-2 gas, which was attributed to Schottky barrier height reduction caused by hydrogen absorption in the catalytic metals. A shift of 0.7 V at 297 K was obtained at a fixed forward current of 0.1 mA after switching from N-2 to 40% H-2 in N-2. The sensor's responses under different concentrations from 2500 ppm H-2 to 40% H-2 in N-2 at 297 K were investigated. Time response of the sensor at a fixed bias of 1 V was given. Finally, the decrease of the Schottky barrier height and the sensitivity of the sensor were calculated. (C) 2008 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hydrogen sensors based on Pt-AlGN/AIN/GaN Schottky diode - art. no. 68291R

Pt/AlGaN/AlN/GaN Schottky diodes have been fabricated and characterized for H-2 sensing. Platinum (Pt) with a thickness of 20nm was evaporated on the sample to form the Schottky contact. The ohmic contact, formed by evaporated Ti/Al/Ni/Au metals, was subsequently annealed by a rapid thermal treatment at 860 degrees C for 30 s in N-2 ambience. Both the forward and reverse current of the device increased greatly when exposed to H-2 gas. The sensor's responses under different hydrogen concentrations from 500ppm to 10% H-2 in N-2 at 300K were investigated. A shift of 0.45V at 297K is obtained at a fixed forward current for switching from N-2 to 10% H-2 in N-2. Time response of the sensor at a fixed bias of 0.5 V was also measured. The turn-on response of the device was rapid, while the recovery of the sensor at N-2 atmosphere was rather slow. But it recovered quickly when the device was exposed to the air. The decrease in the barrier height of the diode was calculated to be about 160meV upon introduction of 10% H-2 into the ambient. The sensitivity of the sensor is also calculated. Some thermodynamics analyses have been done according to the Langmuir isotherm equation.

CONTROLLING OF SCHOTTKY-BARRIER HEIGHTS FOR AU/N-GAAS AND TI/N-GAAS WITH HYDROGEN INTRODUCED AFTER METAL-DEPOSITION BY BIAS ANNEALING

Up to now, in most of the research work done on the effect of hydrogen on a Schottky barrier, the hydrogen was introduced into the semiconductor before metal deposition. This letter reports that hydrogen can be effectively introduced into the Schottky barriers (SBs) of Au/n-GaAs and Ti/n-GaAs by plasma hydrogen treatment (PHT) after metal deposition on [100] oriented n-GaAs substrates. The Schottky barrier height (SBH) of a SB containing hydrogen shows the zero/reverse bias annealing (ZBA/RBA) effect. ZBA makes the SBH decrease and RBA makes it increase. The variations in the SBHs are reversible. In order to obtain obvious ZBA/RBA effects, selection of the temperature for plasma hydrogen treatment is important, and it is indicated that 100-degrees-C for Au/n-GaAs and 150-degrees-C for Ti/n-GaAs are suitable temperatures. It is concluded from the analysis of experimental results that only the hydrogen located at or near the metal-semiconductor interface, rather than the hydrogen in the bulk of either the semiconductor or the metal, is responsible for the ZBA/RBA effect on SBH.

Influence of the semi-insulating GaAs Schottky pad on the Schottky barrier in the active layer

The influence of the sidegate voltage on the Schottky barrier in the ion-implanted active layer via the Schottky pad on the semi-insulating GaAs substrate was observed, and the mechanism for such an influence was proposed. (C) 1996 American Institute of Physics.

Sidegating effect on Schottky contact in ion-implanted GaAs

The sidegating effect on the Schottky barrier in ion-implanted GaAs was investigated with capacitance-voltage profiling at various negative substrate voltages. It was demonstrated that the negative substrate voltage modulates the Schottky depletion region width as well as the space charge region at the substrate-active channel interface. (C) 1995 American Institute of Physics.

SiC Schottky结反向特性的研究

对Ti/6H-SiC Schottky结的反向特性进行了测试和理论分析,提出了一种综合的包括SiC Schottky结主要反向漏电流产生机理的反向隧穿电流模型,该模型考虑了Schottky势垒不均匀性、Ti/SiC界面层电压降和镜像力对SiC Schottky结反向特性的影响,模拟结果和测量值的相符说明了以上所考虑因素是引起SiC Schottky结反向漏电流高于常规计算值的主要原因.分析结果表明在一般工作条件下SiC Schottky结的反向特性主要是由场发射和热电子场发射电流决定的.

6H—SiC Schottky二极管的正向特性

提出了一种考虑Schottky结势垒不均匀性和界面层作用的SiC Schottky二极管(SBD)正向特性模型，势垒的不均匀性来自于SiC外延层上的各种缺陷，而界面层上的压降会使正向Schottky结的有效势垒增高．该模型能够对不同温度下SiC Schottky结正向特性很好地进行模拟，模拟结果和测量数据相符．它更适用于考虑器件温度变化的场合，从机理上说明了理想因子、有效势垒和温度的关系．

Low-frequency noise properties of GaN Schottky barriers deposited on intermediate temperature buffer layers

Metal-semiconductor-metal (MSM) structures were fabricated by RF-plasma-assisted MBE using different buffer layer structures. One type of buffer structure consists of an AlN high-temperature buffer layer (HTBL) and a GaN intermediate temperature buffer layer (ITBL), another buffer structure consists of just a single A IN HTBL. Systematic measurements in the flicker noise and deep level transient Fourier spectroscopy (DLTFS) measurements were used to characterize the defect properties in the films. Both the noise and DLTFS measurements indicate improved properties for devices fabricated with the use of ITBL and is attributed to the relaxation of residue strain in the epitaxial layer during growth process. (C) 2003 Elsevier Ltd. All rights reserved.