Influence of a tilted cavity on quantum-dot optoelectronic active devices

Quantum-dot laser diodes (QD-LDs) with a Fabry-Perot cavity and quantum-dot semiconductor optical amplifiers (QD-SOAs) with 7° tilted cavity were fabricated. The influence of a tilted cavity on optoelectronic active devices was also investigated. For the QD-LD, high performance was observed at room temperature. The threshold current was below 30 mA and the slope efficiency was 0.36 W/A. In contrast, the threshold current of the QD-SOA approached 1000 mA, which indicated that low facet reflectivity was obtained due to the tilted cavity design.A much more inverted carrier population was found in the QD-SOA active region at high operating current, thus offering a large optical gain and preserving the advantages of quantum dots in optical amplification and processing applications. Due to the inhomogeneity and excited state transition of quantum dots, the full width at half maximum of the electroluminescence spectrum of the QD-SOA was 81.6 nm at the injection current of 120 mA, which was ideal for broad bandwidth application in a wavelength division multiplexing system. In addition, there was more than one lasing peak in the lasing spectra of both devices and the separation of these peak positions was 6-8 nm,which is approximately equal to the homogeneous broadening of quantum dots.

MS/RF CMOS工艺兼容的光电探测器模拟与测试

设计了一种新型的与MS/RF CMOS工艺全兼容、带深n阱(DNW)、浅沟槽隔离(STI)的双光电探测器,分析了其工作机理,用器件模拟软件ATLAS对其暗电流、响应电流、光调制频率响应和波长响应进行了模拟.采用TSMC 0.18 μm MS/RF CMOS工艺进行了流片,对芯片进行了暗电流和响应度的测试.模拟和测试结果均表明,该探测器与常规双光电探测器相比,具有较低的暗电流和较高的响应度.

Layout Design and Optimization of RF Spiral Inductors on Silicon Substrate

The effects of key geometrical parameters on the performance of integrated spiral inductors are investigated with the 3D electromagnetic simulator HFSS. While varying geometrical parameters such as the number of turns （N）,the width of the metal traces （W）,the spacing between the traces （S）,and the inner diameter （ID）, changes in the performance of the inductors are analyzed in detail. The reasons for these changes in performance are presented. Simulation results indicate that the performance of an integrated spiral inductor can be improved by optimizing its layout. Some design rules are summarized.

蓝宝石衬底上单晶InAlGaN外延膜的RF-MBE生长

利用射频等离子体辅助分子束外延技术在蓝宝石衬底上外延了晶体质量较好的单晶InAlGaN薄膜．在生长InAlGaN外延层时，获得了外延膜的二维生长，卢瑟福背散射测量结果表明，InAlGaN外延层中In，Al和Ga的组分分别为2％，22％和76％，并且元素的深度分布比较均匀，InAlGaN（0002）三晶X射线衍射摇摆曲线的半高宽为4．8′，通过原子力显微镜观察外延膜表面存在小山丘状的突起和一些小坑，测量得到外延膜表面的均方根粗糙度为2．2nm．利用光电导谱测量InAlGaN的带隙为3．76eV．

Monolithically Integrated Optoelectronic Receivers Implemented in 0. 25μm MS/RF CMOS

A monolithically integrated optoelectronic receiver is presented. A silicon-based photo-diode and receiver circuits are integrated on identical substrates in order to eliminate the parasitics induced by hybrid packaging. Implemented in the present deep sub-micron MS/RF （mixed signal, radio frequency） CMOS,this monolithically OEIC takes advantage of several new features to improve the performance of the photo-diode and eventually the whole OEIC.

MS／RF CMOS工艺兼容的光电探测器

为实现光纤通信系统中的单片光电集成，采用工业标准工艺设计了硅基光电探测器，讨论了光电探测器的机理，提出了五种新的探测器结构，并采用TSMC0．18μmMS／RF CMOS工艺进行了流片．利用半导体测试仪对芯片进行了测试，包括探测器的暗电流、响应度和结电容，并分析了深n阱、浅沟槽隔离等工艺步骤对探测器参数的影响．结果表明，利用标准MS／RF CMOS工艺实现的光电探测器具有良好的特性。

蓝宝石衬底上单晶InN外延膜的RF-MBE生长

采用低温氮化铟(InN)缓冲层，利用射频等离子体辅助分子束外延(RF-MBE)方法在蓝宝石衬底上获得了晶体质量较好的单晶InN外延膜．用光学显微镜观察所外延的InN单晶薄膜，表面无铟滴．InN(0002)双晶X射线衍射摇摆曲线的半高宽为14′；用原子力显微镜测得的表面平均粗糙度为3．3nm；Hall测量表明InN外延膜的室温背景电子浓度为3．3×10^18cm^3，相应的电子迁移率为262cm^2／(V·s)．

RF-MBE Grown AlGaN/GaN HEMT Structure with High Al Content

A Si doped AlGaN/GaN HEMT structure with high Al content (x= 44%) in the barrier layer is grown on sapphire substrate by RF-MBE. The structural and electrical properties of the heterostructure are investigated by the triple axis X-ray diffraction and Van der Pauw-Hall measurement, respectively. The observed prominent Bragg peaks of the GaN and AlGaN and the Hall results show that the structure is of high quality with smooth interface.fabricated and characterized. Better DC characteristics, maximum drain current of 1.0A/mm and extrinsic transconductance of 218mS/mm are obtained when compared with HEMTs fabricated using structures with lower Al mole fraction in the AlGaN barrier layer. The results suggest that the high Al content in the AlGaN barrier layer is promising in improving material electrical properties and device performance.

Dynamics of Cavity Polaritons in a GaAs Quantum-well Semiconductor Microcavity

To provide the dynamics of cavity polariton in semiconductor microcavity containing GaAs quantum-well, the dispersions of the three cavity polaritons have been given by the model of three coupled oscillators, meanwhile the linewidths, group velocities and the mass of the three cavity polaritons have been demonstrated. The results indicated that because of the weight occupied by the photon, heavy hole exciton and light hole extiton in the three cavity ploariton the cavity polaritons exhibited different dynamic behaviors.

Effect of Mesa Size on Thermal Characteristics of Vertical-cavity Surface-emitting Lasers

The effect of mesa size on the thermal characteristics of etched mesa vertical-cavity surfaceemitting lasers(VCSELs) is studied. The numerical results show that the mesa size of the top mirror strongly influences the temperature distribution inside the etched mesa VCSEL. Under a certain driving voltage, with decreasing mesa size, the location of the maximal temperature moves towards the p-contact metal, the temperature in the core region of the active layer rises greatly, and the thermal characteristics of the etched mesa VCSELs will deteriorate.

Fabrication of 1.55μm Si-Based Resonant Cavity Enhanced Photodetectors

A novel bonding method using silicate gel as bonding medium is developed.High reflective SiO2/Si mirrors deposited on silicon substrates by e-beam deposition are bonded to the active layers at a low temperature of 350℃ without any special treatment on bonding surfaces.The reflectivities of the mirrors can be as high as 99.9%.A Si-based narrow band response InGaAs photodetector is successfully fabricated,with a quantum efficiency of 22.6% at the peak wavelength of 1.54μm,and a full width at half maximum of about 27nm.This method has a great potential for industry processes.

Fabrication of SiGe/Si Multi-Quantum Wells Resonant-Cavity-Enhanced Detector

A SiGe/Si multi-quantum wells resonant-cavity-enhanced(RCE) detector with high reflectivity bottom mirror is fabricated by a new method.The bottom mirror is deposited in the hole,which is etched from the backside of the sample by ethylenediamine-pyrocatechol-water(EPW) solution with the buried SiO2 layer in SOI substrate as the etching-stop layer.Reflectivity spectrum indicates that the mirror deposited in the hole has a reflectivity as high as 99% in the range of 1.2～1.5μm.The peak responsivity of the RCE detector at 1.344μm is 1.2mA/W and the full width at half maximum is 12nm.Compared with the conventional p-i-n photodetector,the responsivity of RCE detector is enhanced 8 times.

1.55μm Fabry-Perot Thermo-Optical Tunable Filter with amorphous-Si as Cavity

A 1.55μm Fabry-Perot (F-P) thermo-optical tunable filter is fabricated. The cavity is made of amorphous silicon (a-Si) layer grown by electron-beam evaporation technique. Due to the excellent thermo-optical property of a-Si, the refractive index of the F-P cavity will be changed by heating; the transmittance resonant peak will therefore shift substantially. The measured tuning range is 12nm, FWHM (full-width-at-half-maximum) of the transmission peak is 9nm, and heating efficiency is 0.1K/mW. The large FWHM is mainly due to the non-ideal coating deposition and mirror undulation. Possible improvements to increase the efficiency of heating are suggested.

Measurement of Cavity Loss and Quasi-Fermi-Level Separation for Fabry-Perot Semiconductor Lasers

A fitting process is used to measure the cavity loss and the quasi-Fermi-level separation for Fabry- Perot semiconductor lasers. From the amplified spontaneous emission (ASE) spectrum, the gain spectrum and single-pass ASE obtained by the Cassidy method are applied in the fitting process. For a 1550nm quantum well InGaAsP ridge waveguide laser, the cavity loss of about ～24cm~(-1) is obtained.

RF-MBE生长AlN/GaN超晶格结构二维电子气材料

用射频等离子体辅助分子束外延技术（RF-MBE）在c面蓝宝石衬底上外延了高质量的GaN膜以及AlN/GaN超晶格结构极化感应二维电子气材料。所获得的掺Si的GaN膜室温电子浓度为2.2 * 10~(18)cm~(-3)，相应的电子迁移率为221cm~2/(V·s);1μm厚的GaN外延膜的（0002）X射线衍射摇摆曲线半高宽（FWHM）为7’；极化感应产生的二维电子气室温电子迁移率达到1086cm~2/(V·s)，相应的二维电子气面密度为7.5 * 10~(12)cm~(-2)。