Welding of Sheet metal using Modified short arc MIG/MAG welding process

In this research work, the results of an investigation dealing with welding of sheet metals with diverse air gap using FastROOT modified short arc welding method and short circuit MAG welding processes have been presented. Welding runs were made under different conditions and, during each run, the different process parameters were continuously monitored. It was found that maximum welding speed and less HAZ are reached under specific welding conditions with FastROOT method with the emphasis on arc stability. Welding results show that modified short arc exhibits a higher electrode melting coefficient and with virtually spatter free droplet transition. By adjusting the short circuit duration the penetration can be controlled with only a small change in electrode deposition. Furthermore, by mixing pulsed MIG welding with modified arc welding the working envelope of the process is greatly extended allowing thicker material sections to be welded with improved weld bead aesthetics. FastROOT is a modified short arc welding process using mechanized or automated welding process based on dip transfer welding, characterized by controlled material deposition during the short circuit of the wire electrode to the workpiece.

Model-based study of a chemical-looping combustion process

Chemical-looping combustion (CLC) is a novel combustion technology with inherent separation of the greenhouse gas CO2. The technique typically employs a dual fluidized bed system where a metal oxide is used as a solid oxygen carrier that transfers the oxygen from combustion air to the fuel. The oxygen carrier is looping between the air reactor, where it is oxidized by the air, and the fuel reactor, where it is reduced by the fuel. Hence, air is not mixed with the fuel, and outgoing CO2 does not become diluted by the nitrogen, which gives a possibility to collect the CO2 from the flue gases after the water vapor is condensed. CLC is being proposed as a promising and energy efficient carbon capture technology, since it can achieve both an increase in power station efficiency simultaneously with low energy penalty from the carbon capture. The outcome of a comprehensive literature study concerning the current status of CLC development is presented in this thesis. Also, a steady state model of the CLC process, based on the conservation equations of mass and energy, was developed. The model was used to determine the process conditions and to calculate the reactor dimensions of a 100 MWth CLC system with bunsenite (NiO) as oxygen carrier and methane (CH4) as fuel. This study has been made in Oxygen Carriers and Their Industrial Applications research project (2008 – 2011), funded by the Tekes – Functional Material program. I would like to acknowledge Tekes and participating companies for funding and all project partners for good and comfortable cooperation.

Developing A Knowledge Management Process Model for Internal IT Organization, Case: Stora Enso Oyj, Corporate IT

The objectives of this Master’s Thesis were to find out what kind of knowledge management strategy would fit best an IT organization that uses ITIL (Information Technology Infrastructure Library) framework for IT Service Management and to create a knowledge management process model to support chosen strategy. The empirical material for this research was collected through qualitative semi-structured interviews of a case organization Stora Enso Corporate IT. The results of the qualitative interviews indicate that codification knowledge management strategy would fit best for the case organization. The knowledge management process model was created based on earlier studies and a literature of knowledge management. The model was evaluated in the interview research and the results showed that the created process model is realistic, useful, and it responds to a real life phenomenon.

Design and manufacture of a microdistillation column

Aim of this thesis was to design and manufacture a microdistillation column. The literature review part of this thesis covers stainless steels, material processing and basics about engineering design and distillation. The main focus, however, is on the experimental part. Experimental part is divided into five distinct sections: First part is where the device is introduced and separated into three parts. Secondly the device is designed part by part. It consists mostly of detail problem solving, since the first drawings had already been drawn and the critical dimensions decided. Third part is the manufacture, which was not fully completed since the final assembly was left out of this thesis. Fourth part is the test welding for the device, and its analysis. Finally some ideas for further studies are presented. The main goal of this thesis was accomplished. The device only lacks some final assembly but otherwise it is complete. One thing that became clear during the process was how difficult it is to produce small and precise steel parts with conventional manufacturing methods. Internal stresses within steel plates and thermal distortions can easily ruin small steel structures. Designing appropriate welding jigs is an important task for even simple devices. Laser material processing is a promising tool for this kind of steel processing because of the flexibility, good cutting quality and also precise and low heat input when welding. Next step in this project is the final assembly and the actual distillation tests. The tests will be carried out at Helsinki University of Technology.

Games in Education and Process Development

The aim of the thesis is to devise a framework for analyzing simulation games, in particular introductory supply chain simulation games which are used in education and process development. The framework is then applied to three case examples which are introductory supply chain simulation games used at Lappeenranta University of Technology. The theoretical part of the thesis studies simulation games in the context of education and training as well as of process management. Simulation games can be seen as learning processes which comprise of briefing, micro cycle, and debriefing which includes observation and reflection as well as conceptualization. The micro cycle, i.e. the game itself, is defined through elements and characteristics. Both briefing and debriefing ought to support the micro cycle. The whole learning process needs to support learning objectives of the simulation game. Based on the analysis of the case simulation games, suggestions on how to boost the debriefing and promote long term effects of the games are made. In addition, a framework is suggested to be used in designing simulation games and characteristics of introductory supply chain simulation games are defined. They are designed for general purposes, are simple and operated manually, are multifunctional interplays, and last about 2.5 4 hours. Participants co operate during a game run and competition arises between different runs or game sessions.

Treatment of oily wastewater by ultrafiltration: The effect of different operating and solution conditions

In many industries, such as petroleum production, and the petrochemical, metal, food and cosmetics industries, wastewaters containing an emulsion of oil in water are often produced. The emulsions consist of water (up to 90%), oils (mineral, animal, vegetable and synthetic), surfactants and other contaminates. In view of its toxic nature and its deleterious effects on the surrounding environment (soil, water) such wastewater needs to be treated before release into natural water ways. Membrane-based processes have successfully been applied in industrial applications and are considered as possible candidates for the treatment of oily wastewaters. Easy operation, lower cost, and in some cases, the ability to reduce contaminants below existing pollution limits are the main advantages of these systems. The main drawback of membranes is flux decline due tofouling and concentration polarisation. The complexity of oil-containing systems demands complementary studies on issues related to the mitigation of fouling and concentration polarisation in membranebased ultrafiltration. In this thesis the effect of different operating conditions (factors) on ultrafiltration of oily water is studied. Important factors are normally correlated and, therefore, their effect should be studied simultaneously. This work uses a novel approach to study different operating conditions, like pressure, flow velocity, and temperature, and solution properties, like oil concentration (cutting oil, diesel, kerosene), pH, and salt concentration (CaCl2 and NaCl)) in the ultrafiltration of oily water, simultaneously and in a systematic way using an experimental design approach. A hypothesis is developed to describe the interaction between the oil drops, salt and the membrane surface. The optimum conditions for ultrafiltration and the contribution of each factor in the ultrafiltration of oily water are evaluated. It is found that the effect on permeate flux of the various factors studied strongly depended on the type of oil, the type of membrane and the amount of salts. The thesis demonstrates that a system containing oil is very complex, and that fouling and flux decline can be observed even at very low pressures. This means that only the weak form of the critical flux exists for such systems. The cleaning of the fouled membranes and the influence of different parameters (flow velocity, temperature, time, pressure, and chemical concentration (SDS, NaOH)) were evaluated in this study. It was observed that fouling, and consequently cleaning, behaved differently for the studied membranes. Of the membranes studied, the membrane with the lowest propensity for fouling and the most easily cleaned was the regenerated cellulose membrane (C100H). In order to get more information about the interaction between the membrane and the components of the emulsion, a streaming potential study was performed on the membrane. The experiments were carried out at different pH and oil concentration. It was seen that oily water changed the surface charge of the membrane significantly. The surface charge and the streaming potential during different stages of filtration were measured and analysed being a new method for fouling of oil in this thesis. The surface charge varied in different stages of filtration. It was found that the surface charge of a cleaned membrane was not the same as initially; however, the permeability was equal to that of a virgin membrane. The effect of filtration mode was studied by performing the filtration in both cross-flow and deadend mode. The effect of salt on performance was considered in both studies. It was found that salt decreased the permeate flux even at low concentration. To test the effect of hydrophilicity change, the commercial membranes used in this thesis were modified by grafting (PNIPAAm) on their surfaces. A new technique (corona treatment) was used for this modification. The effect of modification on permeate flux and retention was evaluated. The modified membranes changed their pore size around 33oC resulting in different retention and permeability. The obtained results in this thesis can be applied to optimise the operation of a membrane plant under normal or shock conditions or to modify the process such that it becomes more efficient or effective.

Novel Robot Solutions for Carrying out Field Joint Welding and Machining in the Assembly of the Vacuum Vessel of ITER

It is necessary to use highly specialized robots in ITER (International Thermonuclear Experimental Reactor) both in the manufacturing and maintenance of the reactor due to a demanding environment. The sectors of the ITER vacuum vessel (VV) require more stringent tolerances than normally expected for the size of the structure involved. VV consists of nine sectors that are to be welded together. The vacuum vessel has a toroidal chamber structure. The task of the designed robot is to carry the welding apparatus along a path with a stringent tolerance during the assembly operation. In addition to the initial vacuum vessel assembly, after a limited running period, sectors need to be replaced for repair. Mechanisms with closed-loop kinematic chains are used in the design of robots in this work. One version is a purely parallel manipulator and another is a hybrid manipulator where the parallel and serial structures are combined. Traditional industrial robots that generally have the links actuated in series are inherently not very rigid and have poor dynamic performance in high speed and high dynamic loading conditions. Compared with open chain manipulators, parallel manipulators have high stiffness, high accuracy and a high force/torque capacity in a reduced workspace. Parallel manipulators have a mechanical architecture where all of the links are connected to the base and to the end-effector of the robot. The purpose of this thesis is to develop special parallel robots for the assembly, machining and repairing of the VV of the ITER. The process of the assembly and machining of the vacuum vessel needs a special robot. By studying the structure of the vacuum vessel, two novel parallel robots were designed and built; they have six and ten degrees of freedom driven by hydraulic cylinders and electrical servo motors. Kinematic models for the proposed robots were defined and two prototypes built. Experiments for machine cutting and laser welding with the 6-DOF robot were carried out. It was demonstrated that the parallel robots are capable of holding all necessary machining tools and welding end-effectors in all positions accurately and stably inside the vacuum vessel sector. The kinematic models appeared to be complex especially in the case of the 10-DOF robot because of its redundant structure. Multibody dynamics simulations were carried out, ensuring sufficient stiffness during the robot motion. The entire design and testing processes of the robots appeared to be complex tasks due to the high specialization of the manufacturing technology needed in the ITER reactor, while the results demonstrate the applicability of the proposed solutions quite well. The results offer not only devices but also a methodology for the assembly and repair of ITER by means of parallel robots.

Performance Measurement of the Logistics Process

The objective of the thesis was to create a performance measurement system for the logistics process of a company. In addition, one goal was to make suggestions for improvements based on description and analysis of the process and current measures. The logistics process was described in detail, and the objectives for it were derived from the company strategy and goals. Suggestions for performance measurement system and process improvement were made based on current state analysis. As a result of the thesis, three new performance measures were decided to take into use. In addition, several improvements were suggested to the ERP system to make process smoother. Some of the improvements have already been added to the system and the rest will be added in the near future.

Supply chain costs of a small board lot: sheet cutting and logistics

Succeeding in small board lot (0-20 tons) deliveries, is not always prosperous and failures as well as extra costs compared to standard costs arise. Failure deliveries from converting plants to customer locations tie a lot of unwanted and unexpected costs. Extra costs are handled as quality costs and more precise, internal failure costs. These costs revolve from unsuccessful truck payloads, redundant warehousing or unfavorable routing as examples. Quality costs are becoming more and more important factor in company’s financial decision making. Actual, realized truck payload correlates with the extra costs occurring, so filling the truck payload all get-out well is a key to lower the extra costs. Case company in this study is Corporation A, business segment Boards. Boards have outsourced half of their converting in order to gain better customer service via flexibility, lead time reductions and logistics efficiency improvements. Examination period of the study is first two quarters of year 2008 and deliveries examined are from converters to the customer locations. In Corporation A’s case, the total loss in failure deliveries is hundreds of thousands of Euros during the examination period. So, the logistics goal of getting the right product to the right place and right time for the least cost, does not completely realize.

Potentials of process intensification in the Finnish petrochemical industry

This research was motivated by the need to examine the potential application areas of process intensification technologies in Neste Oil Oyj. According to the company’s interest membrane reactor technology was chosen and applicability of this technology in refining industry was investigated. Moreover, Neste Oil suggested a project which is related to the CO2 capture from FCC unit flue gas stream. The flowrate of the flue gas is 180t/h and consist of approximately 14% by volume CO2. Membrane based absorption process (membrane contactor) was chosen as a potential technique to model CO2 capture from fluid catalytic cracking (FCC) unit effluent. In the design of membrane contactor, a mathematical model was developed to describe CO2 absorption from a gas mixture using monoethanole amine (MEA) aqueous solution. According to the results of literature survey, in the hollow fiber contactor for laminar flow conditions approximately 99 % percent of CO2 can be removed by using a 20 cm in length polyvinylidene fluoride (PDVF) membrane. Furthermore, the design of whole process was performed by using PRO/II simulation software and the CO2 removal efficiency of the whole process obtained as 97 %. The technical and economical comparisons among existing MEA absorption processes were performed to determine the advantages and disadvantages of membrane contactor technology.

Koneinvestoinnin suunnittelu valmistavaan teollisuuteen

Tämän diplomityön tavoitteena oli tutustua ohutlevyjen nykyaikaisiin koneellisiin leikkausmenetelmiin ja tutkia niiden soveltuvuutta yrityksen tarpeisiin. Kohdeyrityksessä investoinnin tarve jakautui tuottavuusinvestoinnin, korvausinvestoinnin ja strategisen investoinnin kesken. Tavoitteena oli luoda investointipolku, jonka avulla poissuljettiin menetelmät, jotka eivät soveltuneet yrityksen tuotantoon. Työn kirjallisuusosuudessa tarkastellaan teoriatietoja, jotka liittyvät yleisesti nykyaikaisiin ohutlevyjen leikkausmenetelmiin sekä investointiprojektin suunnitteluun ja toteutuksen teoriaan. Lisäksi käsitellään investointeihin liittyviä kannattavuus- ja kustannuslaskennan perusperiaatteita. Työn empiirisessä osassa selvitettiin yrityksen ohutlevyosien valmistuksen periaatteita nykytila-analyysin avulla. Tämän perusteella määritettiin nykyaikaisista markkinoilla olevista menetelmistä yritykselle soveltuvin. Tutkimuksen perusteella laserleikkaus oli menetelmistä soveltuvin. Perusinvestoinniltaan laser oli vaihtoehtoisista menetelmistä kallein, mutta se soveltui käytettävyyden, tehokkuuden, joustavuuden ja muiden ominaisuuksiensa perusteella parhaiten tuotannon tarpeisiin. Työn merkittävimmät tulokset osoittivat, että investoinnin kannattavuus riippui koneelle saatavasta käyttösuhteesta. Uusien koneiden tehokkuus lyhentäisi tuotannon läpimenoaikoja, mutta ilman riittävää kapasiteetin käyttöastetta kappaleiden omakustannusarvo nousisi. Lopputulokset ja suositukset on esitetty työn lopussa.

Alumiinipainevalujen purseen- ja jäysteenpoiston kehitysmahdollisuudet

Valupurseiden ja jäysteiden poistaminen on osa alumiinipainevalujen tuotantoprosessia. Työssä on tutkittu käytössä olevien ja uusien menetelmien mahdollisuuksia taloudellisempaan tuotantoon. Purseiden ja jäysteiden poistamiseen käytettävien menetelmien lisäksi tutkimuskohteita ja ideoita on haettu muista metallien työstömenetelmistä. Valupurseiden ja jäysteiden määritelmiä, muodostumista ja luokittelua on esitelty laajasti. Menetelmien tutkimus on painottunut valupurseiden poistamiseen ja valun jälkeistä leikkaamista on tutkittu erityisesti sisäpuolisten muotojen työstämiseen käytettyjen pistintyökalujen kautta. Muotin ulostyöntötapin purseen poistaminen on ollut tärkeä asia menetelmien tutkimuksissa. Valupurseiden, leikkaus- ja koneistusjäysteiden poistamiseksi lastuavista työstömenetelmistä tutkittuja ovat koneistaminen koneistuskeskuksella, aventaminen, hiertopuhallus, suihkuhiertäminen, vesisuihkuleikkaus, ultraäänityöstö, harjaus, painehiertäminen, hiominen kohdistetuilla ja kohdistamattomilla menetelmillä. Myös terminen jäysteenpoistomenetelmä (TEM), kemiallinen työstö (ECM) ja laserleikkaus on otettu esiin tutkimuksessa. Työn tuloksena on näkemys tutkittujen menetelmien jatkokehitystarpeesta ja mahdollisuudesta soveltaa niitä sarjatuotantoon.

Pk-yrityksen layout-suunnittelu ohutlevytuoteteollisuudessa

Diplomityössä käsitellään omistajanvaihdon myötä tapahtuvaa yritysten yhdentymistä pkt- sektorilla. Tutkimuksen tarkoituksena oli suunnitella layout uuteen halliin sekä suunnitella muuttoprosessi kokonaisuudessaan. Tutkimuksessa käsiteltiin koneiden siirron lisäksi myös yritysten yhdentymistä ja yritysfuusiota. Ratkaisumalleja haettiin kirjallisuudesta, tuotannon seuraamisesta ja edellisistä muutoista syntyneistä kokemuksista. Työn aikana kartoitettiin yritysten nykytilanne ja etsittiin siellä olevat parantamista vaativat kohdat. Lisäksi selvitettiin yritysten tuotanto layout -suunnittelua varten. Layoutin tekemisen runkona käytettiin Mutherin -layoutkaaviota. Tietojen pohjalta tehtiin kolme erillistä mallia, joista hyötyarvomatriisia hyväksi käyttäen valittiin yksi. Lisäksi yritysten yhdentymisen työkirjan avulla tehtiin lista tarvittavista toimenpiteistä ennen muuttoa sekä muuton jälkeen. Tutkimuksessa käsiteltiin myös yrityksen ohjelmainvestointeja sekä levytyökeskuksen että laserleikkauskoneen nestaukseen. Lisäksi työssä käsiteltiin myös uusia koneinvestointeja ja uutta organisaatiokaaviota.