Studies on diamond-like carbon and novel diamond-like carbon polymer hybrid coatings deposited with filtered pulsed arc discharge method

The main obstacle for the application of high quality diamond-like carbon (DLC) coatings has been the lack of adhesion to the substrate as the coating thickness is increased. The aim of this study was to improve the filtered pulsed arc discharge (FPAD) method. With this method it is possible to achieve high DLC coating thicknesses necessary for practical applications. The energy of the carbon ions was measured with an optoelectronic time-of-flight method. An in situ cathode polishing system used for stabilizing the process yield and the carbon ion energies is presented. Simultaneously the quality of the coatings can be controlled. To optimise the quality of the deposition process a simple, fast and inexpensive method using silicon wafers as test substrates was developed. This method was used for evaluating the suitability of a simplified arc-discharge set-up for the deposition of the adhesion layer of DLC coatings. A whole new group of materials discovered by our research group, the diamond-like carbon polymer hybrid (DLC-p-h) coatings, is also presented. The parent polymers used in these novel coatings were polydimethylsiloxane (PDMS) and polytetrafluoroethylene (PTFE). The energy of the plasma ions was found to increase when the anode-cathode distance and the arc voltage were increased. A constant deposition rate for continuous coating runs was obtained with an in situ cathode polishing system. The novel DLC-p-h coatings were found to be water and oil repellent and harder than any polymers. The lowest sliding angle ever measured from a solid surface, 0.15 ± 0.03°, was measured on a DLC-PDMS-h coating. In the FPAD system carbon ions can be accelerated to high energies (≈ 1 keV) necessary for the optimal adhesion (the substrate is broken in the adhesion and quality test) of ultra thick (up to 200 µm) DLC coatings by increasing the anode-cathode distance and using high voltages (up to 4 kV). An excellent adhesion can also be obtained with the simplified arc-discharge device. To maintain high process yield (5µm/h over a surface area of 150 cm2) and to stabilize the carbon ion energies and the high quality (sp3 fraction up to 85%) of the resulting coating, an in situ cathode polishing system must be used. DLC-PDMS-h coating is the superior candidate coating material for anti-soiling applications where also hardness is required.

Original Pirate Material : Translating Justin Somper's Demons of the Ocean

Tutkielma käsittelee suomentamani Vampiraatit: Kirottujen laiva -nuortenromaanin käännösprosessia. Materiaalina on kustantajalle toimittamani näytekäännös, joka käsittää yhden kokonaisen luvun ja lisäksi kirjan tapahtumiin keskeisesti liittyvän runon. Molemmista tarkastellaan sekä lopullisia, julkaistuja versioita että ensimmäisiä raakaversioita. Julkaistut versiot ovat osa varsinaista tutkielmaa, raakaversiot ja lähtötekstit puolestaan on sisällytetty mukaan liitteinä. Tarkastelunäkökulmani on pääosin deskriptiivinen ja kontrastiivinen. Proosa-analyysi jakautuu kahteen osaan. Ensimmäisessä osassa tutkin tapoja, joilla käännökseni vastustaa ns. lisääntyvän standardisoitumisen lakia (the law of growing standardization), jota Gideon Toury on ehdottanut yleispäteväksi käännöslaiksi. Touryn laki ennustaa, että käännökset ovat useimmiten tyylillisesti alkuteoksiaan latteampia. Esimerkkini kuitenkin osoittavat, että kääntäjän on mahdollista valita ratkaisunsa niin, että latistumiselta vältytään, ainakin silloin, kun lähtöteksti on melko suoraviivaista. Proosa-analyysin jälkimmäinen osa keskittyy käännöksen muokkaamiseen. Vertaan siinä näytekäännös-luvun ensimmäistä versiota julkaistuun versioon ja tutkin muun muassa sitä, missä määrin ensimmäinen versio sisältää lähtökielen interferenssiä, ts. missä määrin englannille tyypilliset rakenteet paistavat siitä läpi. Tarkastelun kohteena ovat myös kohdekieliset kömpelyydet ja niiden poistaminen sekä pienet mutta kokonaisuuden kannalta tärkeät tyylilliset muutokset. Esimerkeistä käy selvästi ilmi kääntämisen prosessimainen luonne. Käännösnäytteeseen sisältyneen runon suomentaminen oli oma erillinen kokonaisuutensa. Tässä osiossa vertailen lähtötekstiä, raakaversiota ja julkaistua käännöstä rinnakkain säkeistö säkeistöltä. Tarkastelussa painottuvat edelleen tekstin muokkaaminen ja hiominen. Analyysien taustaksi esittelen lyhyesti alkuteoksen ja sen kirjoittajan Justin Somperin. Kuvailen myös omaa käännösfilosofiaani ja esittelen kaksi siihen voimakkaasti vaikuttanutta suomentajaa.

Principles of Pitch Organization in Béla Bartók's 'Duke Bluebeard's Castle'

The topic of my doctoral thesis is to demonstrate the usefulness of incorporating tonal and modal elements into a pitch-web square analysis of Béla Bartók's (1881-1945) opera, 'A kékszakállú herceg vára' ('Duke Bluebeard's Castle'). My specific goal is to demonstrate that different musical materials, which exist as foreground melodies or long-term key progressions, are unified by the unordered pitch set {0,1,4}, which becomes prominent in different sections of Bartók's opera. In Bluebeard's Castle, the set {0,1,4} is also found as a subset of several tetrachords: {0,1,4,7}, {0,1,4,8}, and {0,3,4,7}. My claim is that {0,1,4} serves to link music materials between themes, between sections, and also between scenes. This study develops an analytical method, drawn from various theoretical perspectives, for conceiving superposed diatonic spaces within a hybrid pitch-space comprised of diatonic and chromatic features. The integrity of diatonic melodic lines is retained, which allows for a non-reductive understanding of diatonic superposition, without appealing to pitch centers or specifying complete diatonic collections. Through combining various theoretical insights of the Hungarian scholar Ernő Lendvai, and the American theorists Elliott Antokoletz, Paul Wilson and Allen Forte, as well as the composer himself, this study gives a detailed analysis of the opera's pitch material in a way that combines, complements, and expands upon the studies of those scholars. The analyzed pitch sets are represented on Aarre Joutsenvirta's note-web square, which adds a new aspect to the field of Bartók analysis. Keywords: Bartók, Duke Bluebeard's Castle (Op. 11), Ernő Lendvai, axis system, Elliott Antokoletz, intervallic cycles, intervallic cells, Allen Forte, set theory, interval classes, interval vectors, Aarre Joutsenvirta, pitch-web square, pitch-web analysis.

Intercultural Learning and Hybridity in the Culture Laboratory

The number of immigrant students in vocational education and training is steadily increasing in Finland. This poses challenges for teachers and schools. This research focuses on emerging questions of intercultural learning in the context of immigrant training, and on a method the Culture Laboratory that was developed in an attempt to respond to the challenges. The main methodological and theoretical framework lies in cultural-historical activity theory, developmental work research, and in the concepts of the intercultural and hybridity. The empirical material consists of videotaped recordings of discussions in the Culture Laboratory. The five main research questions focused on the strengths and limitations of the Culture Laboratory as a tool for intercultural learning, the significance of disturbances in it, the potential of suggestions for intercultural learning, paper as a mediating artifact , and the concept of intercultural space. The findings showed that the Culture Laboratory offered a solid background for developing intercultural learning. The disturbances manifested revealed a multitude of scripts and activities. It was also suggested that the structure of expansive learning could start from externalization instead of internalization. The suggestions the participants made opened up a hybrid learning space for intercultural development, and offered a good springboard for new ideas. Learning in Paperland posed both challenges and opportunities for immigrant students, and different paper trails emerged. Intercultural space in the Culture Laboratory was a developmental zone in which a hybrid process of observing, comparing, and creating took place. Key words: intercultural learning, immigrant training, cultural-historical activity theory, developmental work research,

Onko varhaisen tuen päiväkoti mahdollinen? : Tutkimus varhaiskasvatuksen yhteisöllisestä kehittämisestä

Is the early childhood day care facility possible? The research considering communal development of the early education. In Finland mothers and fathers look after 400 000 pre-school children. Half of these attend day care facilities, in which 50 000 staff are employed. The aim of this research is to develop co-operation practices within the day care centre. This research refines and expands my own interest in and knowledge of day care management and content development. The basis of the research draws upon ethnographic material covering the period 1999–2005. The day care centre chosen as a central informant was the first suburban centre founded in 1963, and it provided a rich local and welfare state research perspective. It became clear that the day care facility’s co-operation practices formed the basis of bringing up children and at the same time produced a new multi-operational and multi-layered community for child participation. Adult day care centre workers bringing up the children as a professional work and solutions defining the conditions for the work are expressed in a child’s upbringing. This obviously has an impact in where as the development of communities. From the human and community scientific point of view, the group of youngest children will take up a future position as key players in communities as essential actors and reformers. The research was carried out as multiphase and multiscientific practical research and iterative data formation. The results verified that the co-operation between parents and day care staff produces important benefits for all the stakeholders. However, the day care staff has difficulties in implementing the benefits. During the research process, it became clear that conceptually day care staff saw the practices as ”very important, but not easily realised in practice”. As a result this demanded further research to address this issue and to extend this to the carefacility’s co-operation practises and their communal and social conditions. The research looks at the carefacility’s co-operation with key stakeholders. At the same time it undertakes an analytical and historical examination of carefacilitys’s with an experimental focus as two day care centres chosen as experimental objects. The results of the research showed that the benefits gained by children were determined by the day care centre’s socio-political structure and the parent’s resources. The research framework categorised early childhood education as generational and gender based structures. As part of the research, the strains endemic to these formations have been examined. The system for bringing up children was created as part of a so called welfare state project by implemented by the Day Care Act in year 1973. The law secured the subjective right for every pre-school child to have access to day care facilities. The law also introduced a labour and sosiopolitical phase and the refinement of the day care facility’s education-care concept. The latest phase that started during the early 1990´s was called the market-based social services strategy. As a result of this phase, state support was limited and the screening function of the law was relaxed. This new strategy resulted in a divisive and bureaucratic social welfare system, that individualised and segregated children and their parents, leaving some families outside the communal and welfare state benefit net. The modern day care centre is a hybrid of different aims. Children spend longer and more irregular time in day care. The families are multicultural and that requires more training for the staff. The work in day care has been enhanced, for example he level of education for the staff has been lowered and productivity has been improved. However, administrative work and different kinds of support and net work functions together with the continuous change have taken over from the work done face to face with children. Staff experiences more pressure as the management and the work load has increased. Consequently the long-term planning and daily implementation of the nuclear task of the day care facility is difficult to control. This will have an effect on both motivation and manageability of the work. Overall quality of the early childhood upbringing has been weakened. The possibilities for the near future were tested in the two day care centres chosen as an experi-ment objects. The analysis of these experiments showed that generative interaction work will benefit everyone: children, parents and employees. The main results of the research are new concepts of an early support day care centre, which can be empirically and theoretically possi-ble for development the near future. Key words: Day care facility’s co-operation practises, early childhood education as generational structure, child’s multi-operational and multi-layered community, multi-subjective operator, generative interaction work, communal composition.

Drug Analysis without Primary Reference Standards : Application of LC-TOFMS and LC-CLND to Biofluids and Seized Material

Drug Analysis without Primary Reference Standards: Application of LC-TOFMS and LC-CLND to Biofluids and Seized Material Primary reference standards for new drugs, metabolites, designer drugs or rare substances may not be obtainable within a reasonable period of time or their availability may also be hindered by extensive administrative requirements. Standards are usually costly and may have a limited shelf life. Finally, many compounds are not available commercially and sometimes not at all. A new approach within forensic and clinical drug analysis involves substance identification based on accurate mass measurement by liquid chromatography coupled with time-of-flight mass spectrometry (LC-TOFMS) and quantification by LC coupled with chemiluminescence nitrogen detection (LC-CLND) possessing equimolar response to nitrogen. Formula-based identification relies on the fact that the accurate mass of an ion from a chemical compound corresponds to the elemental composition of that compound. Single-calibrant nitrogen based quantification is feasible with a nitrogen-specific detector since approximately 90% of drugs contain nitrogen. A method was developed for toxicological drug screening in 1 ml urine samples by LC-TOFMS. A large target database of exact monoisotopic masses was constructed, representing the elemental formulae of reference drugs and their metabolites. Identification was based on matching the sample component s measured parameters with those in the database, including accurate mass and retention time, if available. In addition, an algorithm for isotopic pattern match (SigmaFit) was applied. Differences in ion abundance in urine extracts did not affect the mass accuracy or the SigmaFit values. For routine screening practice, a mass tolerance of 10 ppm and a SigmaFit tolerance of 0.03 were established. Seized street drug samples were analysed instantly by LC-TOFMS and LC-CLND, using a dilute and shoot approach. In the quantitative analysis of amphetamine, heroin and cocaine findings, the mean relative difference between the results of LC-CLND and the reference methods was only 11%. In blood specimens, liquid-liquid extraction recoveries for basic lipophilic drugs were first established and the validity of the generic extraction recovery-corrected single-calibrant LC-CLND was then verified with proficiency test samples. The mean accuracy was 24% and 17% for plasma and whole blood samples, respectively, all results falling within the confidence range of the reference concentrations. Further, metabolic ratios for the opioid drug tramadol were determined in a pharmacogenetic study setting. Extraction recovery estimation, based on model compounds with similar physicochemical characteristics, produced clinically feasible results without reference standards.

Multiplication of hybrid aspen (Populus tremula L. x P. tremuloides Michx.) from cuttings

The primary aim of the present study was to find an efficient and simple method of vegetative propagation for producing large numbers of hybrid aspen (Populus tremuloides L. x P. tremula Michx.) plants for forest plantations. The key objectives were to investigate the main physiological factors that affect the ability of cuttings to regenerate and to determine whether these factors could be manipulated by different growth conditions. In addition, clonal variation in traits related to propagation success was examined. According to our results, with the stem cutting method, depending on the clone, it is possible to obtain only 1−8 plants from one stock plant per year. With the root cutting method the corresponding values for two-year-old stock plants are 81−207 plants. The difference in number of cuttings between one- and two-year-old stock plants is so pronounced that it is economically feasible to grow stock plants for two years. There is no reason to use much older stock plants as a source of cuttings, as it has been observed that rooting ability diminishes as root diameter increases. Clonal variation is the most important individual factor in propagation of hybrid aspen. The fact that the efficiently sprouted clones also rooted best facilitates the selection of clones for large-scale propagation. In practice, root cuttings taken from all parts of the root system of hybrid aspen were capable of producing new shoots and roots. However, for efficient rooting it is important to use roots smaller than one centimeter in diameter. Both rooting and sprouting, as well as sprouting rate, were increased by high soil temperature; in our studies the highest temperature tested (30ºC) was the best. Light accelerated the sprouting of root cuttings, but they rooted best in dark conditions. Rooting is essential because without roots the sprouted cutting cannot survive long. For aspen the criteria for clone selection are primarily fiber qualities and growth rate, but ability to regenerate efficiently is also essential. For large-scale propagation it is very important to find clones from which many cuttings per stock plant can be obtained. In light of production costs, however, it is even more important that the regeneration ability of the produced cuttings be high.

TlBr raw material purification, crystal growth, annealing, detector fabrication and characterisation for gamma-ray detector applications

The research reported in this thesis dealt with single crystals of thallium bromide grown for gamma-ray detector applications. The crystals were used to fabricate room temperature gamma-ray detectors. Routinely produced TlBr detectors often are poor quality. Therefore, this study concentrated on developing the manufacturing processes for TlBr detectors and methods of characterisation that can be used for optimisation of TlBr purity and crystal quality. The processes under concern were TlBr raw material purification, crystal growth, annealing and detector fabrication. The study focused on single crystals of TlBr grown from material purified by a hydrothermal recrystallisation method. In addition, hydrothermal conditions for synthesis, recrystallisation, crystal growth and annealing of TlBr crystals were examined. The final manufacturing process presented in this thesis deals with TlBr material purified by the Bridgman method. Then, material is hydrothermally recrystallised in pure water. A travelling molten zone (TMZ) method is used for additional purification of the recrystallised product and then for the final crystal growth. Subsequent processing is similar to that described in the literature. In this thesis, literature on improving quality of TlBr material/crystal and detector performance is reviewed. Aging aspects as well as the influence of different factors (temperature, time, electrode material and so on) on detector stability are considered and examined. The results of the process development are summarised and discussed. This thesis shows the considerable improvement in the charge carrier properties of a detector due to additional purification by hydrothermal recrystallisation. As an example, a thick (4 mm) TlBr detector produced by the process was fabricated and found to operate successfully in gamma-ray detection, confirming the validity of the proposed purification and technological steps. However, for the complete improvement of detector performance, further developments in crystal growth are required. The detector manufacturing process was optimized by characterisation of material and crystals using methods such as X-ray diffraction (XRD), polarisation microscopy, high-resolution inductively coupled plasma mass (HR-ICPM), Fourier transform infrared (FTIR), ultraviolet and visual (UV-Vis) spectroscopy, field emission scanning electron microscope (FESEM) and energy-dispersive X-ray spectroscopy (EDS), current-voltage (I-V) and capacity voltage (CV) characterisation, and photoconductivity, as well direct detector examination.

Phylogeography and hybrid swarms: history of brackish water bivalve diversity in North European marginal seas

This study addressed the large-scale molecular zoogeography in two brackish water bivalve molluscs, Macoma balthica and Cerastoderma glaucum, and genetic signatures of the postglacial colonization of Northern Europe by them. The traditional view poses that M. balthica in the Baltic, White and Barents seas (i.e. marginal seas) represent direct postglacial descendants of the adjacent Northeast Atlantic populations, but this has recently been challenged by observations of close genetic affinities between these marginal populations and those of the Northeast Pacific. The primary aim of the thesis was to verify, quantify and characterize the Pacific genetic contribution across North European populations of M. balthica and to resolve the phylogeographic histories of the two bivalve taxa in range-wide studies using information from mitochondrial DNA (mtDNA) and nuclear allozyme polymorphisms. The presence of recent Pacific genetic influence in M. balthica of the Baltic, White and Barents seas, along with an Atlantic element, was confirmed by mtDNA sequence data. On a broader temporal and geographical scale, altogether four independent trans-Arctic invasions of Macoma from the Pacific since the Miocene seem to have been involved in generating the current North Atlantic lineage diversity. The latest trans-Arctic invasion that affected the current Baltic, White and Barents Sea populations probably took place in the early post-glacial. The nuclear genetic compositions of these marginal sea populations are intermediate between those of pure Pacific and Atlantic subspecies. In the marginal sea populations of mixed ancestry (Barents, White and Northern Baltic seas), the Pacific and Atlantic components are now randomly associated in the genomes of individual clams, which indicates both pervasive historical interbreeding between the previously long-isolated lineages (subspecies), and current isolation of these populations from the adjacent pure Atlantic populations. These mixed populations can be characterized as self-supporting hybrid swarms, and they arguably represent the most extensive marine animal hybrid swarms so far documented. Each of the three swarms still has a distinct genetic composition, and the relative Pacific contributions vary from 30 to 90 % in local populations. This diversity highlights the potential of introgressive hybridization to rapidly give rise to new evolutionarily and ecologically significant units in the marine realm. In the south of the Danish straits and in the Southern Baltic Sea, a broad genetic transition zone links the pure North Sea subspecies M. balthica rubra to the inner Baltic hybrid swarm, which has about 60 % of Pacific contribution in its genome. This transition zone has no regular smooth clinal structure, but its populations show strong genotypic disequilibria typical of a hybrid zone maintained by the interplay of selection and gene flow by dispersing pelagic larvae. The structure of the genetic transition is partly in line with features of Baltic water circulation and salinity stratification, with greater penetration of Atlantic genes on the Baltic south coast and in deeper water populations. In all, the scenarios of historical isolation and secondary contact that arise from the phylogeographic studies of both Macoma and Cerastoderma shed light to the more general but enigmatic patterns seen in marine phylogeography, where deep genetic breaks are often seen in species with high dispersal potential.

Randomised Evaluation of New Technologies within the Population‐Based Cervical Cancer Screening Programme in Finland: Cross‐Sectional Performance and Validity

A randomised and population-based screening design with new technologies has been applied to the organised cervical cancer screening programme in Finland. In this experiment the women invited to routine five-yearly screening are individually randomised to be screened with automation-assisted cytology, human papillomavirus (HPV) test or conventional cytology. By using the randomised design, the ultimate aim is to assess and compare the long-term outcomes of the different screening regimens. The primary aim of the current study was to evaluate, based on the material collected during the implementation phase of the Finnish randomised screening experiment, the cross-sectional performance and validity of automation-assisted cytology (Papnet system) and primary HPV DNA testing (Hybrid Capture II assay for 13 oncogenic HPV types) within service screening, in comparison to conventional cytology. The parameters of interest were test positivity rate, histological detection rate, relative sensitivity, relative specificity and positive predictive value. Also, the effect of variation in performance by screening laboratory on age-adjusted cervical cancer incidence was assessed. Based on the cross-sectional results, almost no differences were observed in the performance of conventional and automation-assisted screening. Instead, primary HPV screening found 58% (95% confidence interval 19-109%) more cervical lesions than conventional screening. However, this was mainly due to overrepresentation of mild- and moderate-grade lesions and, thus, is likely to result in overtreatment since a great deal of these lesions would never progress to invasive cancer. Primary screening with an HPV DNA test alone caused substantial loss in specificity in comparison to cytological screening. With the use of cytology triage test, the specificity of HPV screening improved close to the level of conventional cytology. The specificity of primary HPV screening was also increased by increasing the test positivity cutoff from the level recommended for clinical use, but the increase was more modest than the one gained with the use of cytology triage. The performance of the cervical cancer screening programme varied widely between the screening laboratories, but the variation in overall programme effectiveness between respective populations was more marginal from the very beginning of the organised screening activity. Thus, conclusive interpretations on the quality or success of screening should not be based on performance parameters only. In the evaluation of cervical cancer screening the outcome should be selected as closely as possible to the true measure of programme effectiveness, which is the number of invasive cervical cancers and subsequent deaths prevented in the target population. The evaluation of benefits and adverse effects of each new suggested screening technology should be performed before the technology becomes an accepted routine in the existing screening programme. At best, the evaluation is performed randomised, within the population and screening programme in question, which makes the results directly applicable to routine use.

Evaluation of the Biocompatibility of Poly (ortho ester), Copolymer of ε-caprolactone/D,L-lactide and the Composite of Copolymer of ε-caprolactone/D,L-lactide and Tricalciumphosphate as Bone Filling Material

The purpose of this series of studies was to evaluate the biocompatibility of poly (ortho) ester (POE), copolymer of ε-caprolactone and D,L-lactide [P (ε-CL/DL-LA)] and the composite of P(ε-CL/DL-LA) and tricalciumphosphate (TCP) as bone filling material in bone defects. Tissue reactions and resorption times of two solid POE-implants (POE 140 and POE 46) with different methods of sterilization (gamma- and ethylene oxide sterilization), P(ε-CL/DL-LA)(40/60 w/w) in paste form and 50/50 w/w composite of 40/60 w/w P(ε-CL/DL-LA) and TCP and 27/73 w/w composite of 60/40 w/w P(ε-CL/DL-LA) and TCP were examined in experimental animals. The follow-up times were from one week to 52 weeks. The bone samples were evaluated histologically and the soft tissue samples histologically, immunohistochemically and electronmicroscopically. The results showed that the resorption time of gamma sterilized POE 140 was eight weeks and ethylene oxide sterilized POE 140 13 weeks in bone. The resorption time of POE 46 was more than 24 weeks. The gamma sterilized rods started to erode from the surface faster than ethylene oxide sterilized rods for both POEs. Inflammation in bone was from slight to moderate with POE 140 and moderate with POE 46. No highly fluorescent layer of tenascin or fibronectin was found in the soft tissue. Bone healing at the sites of implantation was slower than at control sites with the copolymer in small bone defects. The resorption time for the copolymer was over one year. Inflammation in bone was mostly moderate. Bone healing at the sites of implantation was also slower than at the control sites with the composite in small and large mandibular bone defects. Bone formation had ceased at both sites by the end of follow-up in large mandibular bone defects. The ultrastructure of the connective tissue was normal during the period of observation. It can be concluded that the method of sterilization influenced the resorption time of both POEs. Gamma sterilized POE 140 could have been suitable material for filling small bone defects, whereas the degradation times of solid EO-sterilized POE 140 and POE 46 were too slow to be considered as bone filling material. Solid material is difficult to contour, which can be considered as a disadvantage. The composites were excellent to handle, but the degradation time of the polymer and the composites were too slow. Therefore, the copolymer and the composite can not be recommended as bone filling material.