小湾电站坝基岩体卸荷工程地质力学研究

Dam is the key main works in the construction of water power. The success or failure of the construction of the dam mainly depends on the stability of the dam foundation. The double curvature arch dam-XiaoWan Dam is the highest one among the dams with the same type in the world, and the water thrust acted on it reaches ton, so the rock bearing capacity of dam foundation becomes more important. Because of the high and steep valley-side slope, the large scale of excavation and the complex body type of excavation, it is prominent that the problem of stress release of the rock mass in dam foundation. More great attentions should be paid for the stability and the degraded of rock properties of rock mass induced by the stress release. In this paper, the phenomena of stress release of rock mass in XiaoWan Dam foundation and its mechanisms were analyzed based on the collection of data, the detailed field engineering investigations, measurement of the rock mass and the 2D numerical calculations. The rock mass under the foundation is weak-weathered to intact, the quality of which is good. After excavation of the foundation, the rock mass near the slope surface occurred extend, stretch and stick-slip along original textures till the new fracture surface formed. Then platy structure of the rock mass takes on. The rock mass in the dam foundation occur resilience due to stress release towards free faces with the characteristics of time effect and localized deformation. In-situ measurements show that the rock mass near the surface are degraded. The stress release induced by excavation is a process of the interaction between engineering structures and geologic body. The stress release of rock mass in dam foundation is related to the changed degree of geometrical conditions. The rock near excavation surface failed nearly under uniaxial stresses. The bending-breaking mechanism of plate girder can interpret the failure model of the rock mass with platy structure in dam foundation slope. In essence, the stress release is the change of stress field including the change of directions and magnitudes of stress induced by excavation, which can induce the comedown of the safety margin. In this paper, the inducing conditions of stress release were calculated by numerical analyses. Moreover, from the point of view that the change of stress field, the coefficient of K, i.e. the variable load coefficient was proposed. Then the law of the change of it is interpreted. The distributional characteristics of fracture zone were expressed by the coefficient. The stress release of hard rock has the characteristic of localization. The measuring technique of sound wave can not reflect the small cracks in this kind of rock mass due to stress release. So, the spectral analysis method was proposed. At the same time, the application foreground in engineering of the Stockwell Time-Frequency- Spectrum method was discussed with a view to the limitation of it.

Well-width dependence of in-plane optical anisotropy in (001) GaAs/AlGaAs quantum wells induced by in-plane uniaxial strain and interface asymmetry

The well-width dependence of in-plane optical anisotropy (IPOA) in (001) GaAs/AlxGa1-xAs quantum wells induced by in-plane uniaxial strain and interface asymmetry has been studied comprehensively. Theoretical calculations show that the IPOA induced by in-plane uniaxial strain and interface asymmetry exhibits much different well-width dependence. The strain-induced IPOA is inversely proportional to the energy spacing between heavy- and light-hole subbands, so it increases with the well width. However, the interface-related IPOA is mainly determined by the probability that the heavy- and light-holes appear at the interfaces, so it decreases with the well width. Reflectance difference spectroscopy has been carried out to measure the IPOA of (001) GaAs/AlxGa1-xAs quantum wells with different well widths. Strain- and interface-induced IPOA have been distinguished by using a stress apparatus, and good agreement with the theoretical prediction is obtained. The anisotropic interface potential parameters are also determined. In addition, the energy shift between the interface- and strain-induced 1H1E reflectance difference (RD) structures, and the deviation of the 1L1E RD signal away from the prediction of the calculation model have been discussed.

The Uniaxial Tensile Deformation of Ni Nanowire: Atomic-Scale Computer Simulations

The mechanical deformations of nickel nanowire subjected to uniaxial tensile strain at 300 K are simulated by using molecular dynamics with the quantum corrected Sutten-Chen many-body force field. We have used common neighbor analysis method to investigate the structural evolution of Ni nanowire during the elongation process. For the strain rate of 0.1%/ps, the elastic limit is up to about 11% strain with the yield stress of 8.6 GPa. At the elastic stage, the deformation is carried mainly through the uniform elongation of the distances between the layers (perpendicular to the Z-axis) while the atomic structure remains basically unchanged. With further strain, the slips in the {111} planes start to take place in order to accommodate the applied strain to carry the deformation partially, and subsequently the neck forms. The atomic rearrangements in the neck region result in a zigzag change in the stress-strain curve; the atomic structures beyond the region, however, have no significant changes. With the strain close to the point of the breaking, we observe the formation of a one-atom thick necklace in Ni nanowire. The strain rates have no significant effect on the deformation mechanism, but have some influence on the yield stress, the elastic limit, and the fracture strain of the nanowire.

Revelation of a Functional Dependence of the Sum of Two Uniaxial Strengths/Hardness on Elastic Work/Total Work of Indentation

Dimensional and finite element analyses were used to analyze the relationship between the mechanical properties and instrumented indentation response of materials. Results revealed the existence of a functional dependence of (engineering yield strength sigma(E,y) + engineering tensile strength sigma(E,b))/Oliver & Pharr hardness on the ratio of reversible elastic work to total work obtained from an indentation test. The relationship links up the Oliver & Pharr hardness with the material strengths, although the Oliver & Pharr hardness may deviate from the true hardness when sinking in or piling up occurs. The functional relationship can further be used to estimate the SUM sigma(E,y) + sigma(E,b) according to the data of an instrumented indentation test. The sigma(E,y) + sigma(E,b) value better reflects the strength of a material compared to the hardness value alone. The method was shown to be effective when applied to aluminum alloys. The relationship can further be used to estimate the fatigue limits, which are usually obtained from macroscopic fatigue tests in different modes.

Local stresses and strains in axially cracked cylindrical shells

A perturbation solution is obtained for the local stress-strain fields in an axially cracked cylindrical shell. The tenth-order differential equations are used that take into account the transverse shear deformation. The perturbation of a curvature parameter, λ, is employed, where . The stress intensity factors for finite size cylindrical shells subjected to bending and internal pressure are evaluated. Sufficient accuracy can be obtained without using fine mesh sizes in regions near the crack tip. Also analyzed are the influence of cylinder diameter and shearing stiffness on bulging.

Abnormal ferroelectric response and enhancement of piezoelectricity of PbTiO3 under uniaxial compression

The ferroelectricity of rhombohedral PbTiO3 under uniaxial compression is investigated from first-principles study. Upon compression, the ferroelectricity decreases until a critical stress of -29 GPa and then increases with a further increase of the magnitude of the uniaxial compressive stress. We also find that uniaxial compression could enhance piezoelectricity and that the maximum piezoelectric coefficient d(33) occurs at sigma(33)=-49 GPa, which supports the experimentally observed piezoelectric behavior in rhombohedral Pb(Mg1/3Nb2/3O3)-0.32PbTiO(3) [Q. Wan, C. Chen, and Y. P. Shen, J. Appl. Phys. 98, 024103 (2005)]. Our calculated results show that the Pb, Ti, and O atoms have different contributions to the total polarization with increasing the magnitude of uniaxial compressive stress, and that when -sigma(33)>55 GPa, the Ti atoms no longer have contributions to the polarization, which leads to the changes of ferroelectricity and piezoelectricity. (C) 2008 American Institute of Physics.

Studies of tetragonal PbTiO3 subjected to uniaxial stress along the c-axis

Tetragonal PbTiO3 under uniaxial stress along the c-axis is investigated from first-principles. The structural parameters, polarization, and squares of the lowest optical phonon frequencies for E(1TO) and A(1)(1TO) modes at Gamma show abrupt changes near a stress sigma(c) of 1.04 GPa, which is related to the dramatic change of elastic constant c(33) resulting from the uniaxial stress applied along the c-axis. We also find that the uniaxial compressive stress could enhance the piezoelectric stress coefficients, whereas the uniaxial tensile stress could enhance the piezoelectric strain coefficients. It is also found that when the magnitude of uniaxial compressive stress sigma(33) is greater than 12 GPa, PbTiO3 is transformed to the paraelectric tetragonal phase.

Room-temperature highly anisotropic ferromagnetism and uniaxial spin amplification in (In,Mn)As quantum dots

The hole-mediated ferromagnetism in (In,Mn)As quantum dots is investigated using the k center dot p method and the mean field model. It is found that the (In,Mn)As quantum dot can be ferromagnetic at room temperature when there is one hole in the dot. For the spherical quantum dots, the Curie temperature decreases as the diameter increases, and increases as the effective composition of magnetic ions increases. It is interesting to find that the (In,Mn)As oblate quantum dot has highly anisotropic Zeeman splitting and ferromagnetism due to the spin-orbit coupling effect, which can be used as an uniaxial spin amplifier. (c) 2008 American Institute of Physics.

Circular photogalvanic effect of the two-dimensional electron gas in AlXGa1-XN/GaN heterostructures under uniaxial strain

The circular photogalvanic effect (CPGE) of the two-dimensional electron gas (2DEG) in Al0.25Ga0.75N/GaN heterostructures induced by infrared radiation has been investigated under uniaxial strain. The observed photocurrent consists of the superposition of the CPGE and the linear photogalvanic effect currents, both of which are up to 10(-2) nA. The amplitude of the CPGE current increases linearly with additional strain and is enhanced by 18.6% with a strain of 2.2x10(-3). Based on the experimental results, the contribution of bulk-inversion asymmetry (BIA) and structure-inversion asymmetry (SIA) spin splitting of the 2DEG to the CPGE current in the heterostructures is separated, and the ratio of SIA and BIA terms is estimated to be about 13.2, indicating that the SIA is the dominant mechanism to induce the k-linear spin splitting of the subbands in the triangular quantum well at AlxGa1-xN/GaN heterointerfaces. (C) 2007 American Institute of Physics.

Tunneling magnetoresistance in devices based on epitaxial NiMnSb with uniaxial anisotropy

We demonstrate tunnel magnetoresistance junctions based on a trilayer system consisting of an epitaxial NiMnSb, an aluminum oxide, and a CoFe trilayer. The junctions show a tunneling magnetoresistance of Delta R/R of 8.7% at room temperature which increases to 14.7% at 4.2 K. The layers show a clear separate switching and a small ferromagnetic coupling. A uniaxial in-plane anisotropy in the NiMnSb layer leads to different switching characteristics depending on the direction in which the magnetic field is applied, an effect which can be used for sensor applications. (c) 2006 American Institute of Physics.

Rashba and Dresselhaus spin-orbit coupling in GaN-based heterostructures probed by the circular photogalvanic effect under uniaxial strain

The spin splitting in GaN-based heterostructures has been investigated by means of circular photogalvanic effect experiments under uniaxial strain. The ratios of Rashba and Dresselhaus spin-orbit coupling coefficients (R/D ratios) have been measured in AlxGa1-xN/GaN heterostructures with various Al compositions. It is found that the R/D ratio increases from 4.1 to 19.8 with the Al composition of the AlxGa1-xN barrier varied from 15% to 36%. The Dresselhaus coefficient of bulk GaN is experimentally obtained to be 0.4 eV angstrom(3). The results indicate that the spin splitting in GaN-based heterostructures can be modulated effectively by the polarization-induced electric fields.

Uniaxial anisotropy and novel magnetic behaviors of CoFe2O4 nanoparticles prepared in a magnetic field

CoFe2O4 nanoparticles prepared by chemical coprecipitation method in a magnetic field exhibit novel magnetic properties. The average particle diameter was about 2 nm and larger depending on the post annealing temperature. Magnetization measurements indicate that smaller nanoparticles are superparamagnetic above their respective blocking temperatures. In the blocked state, these nanoparticles exhibit interesting behaviors in the magnetic hysteresis measurements. Constricted, or wasp waisted with extremely narrow waist, hysteresis curves have been observed in the magnetization versus field sweeps. For larger nanoparticles, the room temperature hysteresis is typical of a ferromagnet with an open loop, but the loop closes at lower temperature. The novel magnetic behavior is attributed to the directional order of Co ions and vacancies in CoFe2O4 established during the coprecipitation of the nanoparticles under an applied field.

FEM Simulations and Optimization about Residual Stresses in Coating Structures with Functionally Graded Materials Layer

An elasto-plastic finite element method is developed to predict the residual stresses of thermal spraying coatings with functionally graded material layer. In numerical simulations, temperature sensitivity of various material constants is included and mix

Analysis of strip electric saturation model of crack problem in piezoelectric materials

This paper presents a fully anisotropic analysis of strip electric saturation model proposed by Gao et al. (1997) (Gao, H.J., Zhang, T.Y., Tong, P., 1997. Local and global energy release rates for an electrically yielded crack in a piezoelectric ceramic. J. Mech. Phys. Solids, 45, 491-510) for piezoelectric materials. The relationship between the size of the strip saturation zone ahead of a crack tip and the applied electric displacement field is established. It is revealed that the critical fracture stresses for a crack perpendicular to the poling axis is linearly decreased with the increase of the positive applied electric field and increases linearly with the increase of the negative applied electric field. For a crack parallel to the poring axis, the failure stress is not effected by the parallel applied electric field. In order to analyse the existed experimental results, the stress fields ahead of the tip of an elliptic notch in an infinite piezoelectric solid are calculated. The critical maximum stress criterion is adopted for determining the fracture stresses under different remote electric displacement fields. The present analysis indicates that the crack initiation and propagation from the tip of a sharp elliptic notch could be aided or impeded by an electric displacement field depending on the field direction. The fracture stress predicted by the present analysis is consistent with the experimental data given by Park and Sun (1995) (Park, S., Sun, C.T., 1995. Fracture criteria for piezoelectric materials. J. Am. Ceram. Soc 78, 1475-1480).

Analysis of Wave-Induced Effective Stresses of Seabed

波浪作用下海床的稳定性分析是海洋工程地质评价的重要内容。海床的稳定性可通过计算分析其随时间变化的有效应力场来评估。建议了一个周期载荷作用下土体的本构模型,并用于计算波浪作用下海床的应力与变形。采用Biot固结理论和有限单元法,分析了海床的动态应力场与孔隙水压力场。波浪作用下两种渗透系数时有效应力的动态变化过程结果对比,反映了渗透消散作用对海床有效应力变化的影响。