Production of Biofuels by Fischer Tropsch Synthesis

Production of biofuel via biomass gasification followed by Fischer Tropsch synthesis is of considerable interest because of the high quality of fuels produced which do not contain sulphur and are free of carbon dioxide. The purpose of this Master’s thesis is to study feasibility production of biofuels integrated with Fischer Tropsch process using Aspen Plus simulation. The simulation results were used to size process equipment and carry out an economic evaluation. The results show that lowering the reactor temperature from 1000 oC - 850 oC and raising the water gas shift temperature from 500 oC - 600 oC can improve overall gas efficiency, which in turn leads to better production of ultra clean syngas for the Fischer Tropsch synthetic reactor. Similarly, the Fischer Tropsch offgas is converted into a gas turbine for power production, and finally biodiesel is produced as fuels for transportation.

Genetic transformation of Eucalyptus camaldulensis by agrobalistic method

Eucalyptus stands in the setting of worldwide forestry due to its adaptability, rapid growth, production of high-quality and low cost of wood pulp fibers. The eucalyptus convetional breeding is impaired mainlly by the long life cycle making the genetic transformation systems an important tool for this purpose. However, this system requires in vitro eficient protocols for plant induction, regeneration and seletion, that allow to obtain transgenic plants from the transformed cell groups. The aim of this work was to evaluate the callus formation and to optimize the leaves and callus genetic transformation protocol by using the Agrobacterium tumefaciens system. Concerning callus formation, two different culture media were evaluated: MS medium supplemented with auxin, cytokinin (M1) and the MS medium with reduced nitrogen concentration and supplemented with auxin, cytokinin coconut water (M2). To establish the leave genetic transformation, those were exposed to agrobiolistics technique (gene gun), to tissue injury, and A. tumesfasciens EHA 105 contening the vetor pCambia 3301 (35S::GUS::NOS), for gene transference and to establish the callus transformation thoses were exposed only to A. tumefasciens. For both experiments, the influence of different infection periods was evaluated. The M2 medium provided the best values for callus sizea and fresh and dry weight. The leaves genetic transformation using the agrobiolistics technique was effective, the gus gene transient expression could be observed. No significant differences were obtained in the infection periods (4, 6 and 8 minutes). The callus genetic transformation with A. tumefaciens also promotend the gus gene transient expression on the callus co-cultiveted for 15 e 30 minutes. The transformed callus was transfered to a regeneration and selection medium and transformed plants were obtained.

Studies in offset ink setting

The offset printing process is complex and involves the meeting of two essentially complex materials, printing ink and paper, upon which the final product is formed. It can therefore be expected that a multitude of chemical and physical interactions and mechanisms take place at the ink-paper interface. Interactions between ink and paper are of interest to both the papermakers and ink producers, as they wish to achieve better quality in the final product. The objective of this work is to clarify the combined influence of paper coating structure, printing ink and fountain solution on ink setting and the problems related to ink setting. A further aim is to identify the mechanisms that influence ink setting problems, and to be able to counteract them by changing properties of the coating layer or by changing the properties of the ink. The work carried out for this thesis included use of many techniques ranging from standard paper and printability tests to advanced optical techniques for detection of ink filaments during ink levelling. Modern imaging methods were applied for assessment of ink filament remain sizes and distribution of ink components inside pigment coating layers. Gravimetric filtration method and assessment of print rub using Ink-Surface-Interaction-Tester (ISIT) were utilized to study the influence of ink properties on ink setting. The chemical interactions were observed with the help of modified thin layer chromatography and contact angle measurements using both conventional and high speed imaging. The results of the papers in this thesis link the press operational parameters to filament sizes and show the influence of these parameters to filament size distribution. The relative importance between the press operation parameters was shown to vary. The size distribution of filaments is important in predicting the ink setting behaviour, which was highlighted by the dynamic gloss and ink setting studies. Prediction of ink setting behaviour was also further improved by use of separate permeability factors for different ink types in connection to filtration equations. The roles of ink components were studied in connection to ink absorption and mechanism of print rub. Total solids content and ratio of linseed oil to mineral oil were found to determine the degree of print rub on coated papers. Wax addition improved print rub resistance, but would not decrease print rub as much as lowering the total solids content in the ink. Linseed oil was shown to absorb into pigment coating pores by mechanism of adsorption to pore walls, which highlights the need for sufficient pore surface area for improved chromatographic separation of ink components. These results should help press operators, suppliers of printing presses, papermakers and suppliers to papermakers, to better understand the material and operating conditions of the press as it relates to various print quality issues. Even though paper is in competition with electronic media, high quality printed products are still in demand. The results should provide useful information for this segment of the industry.

Strategisten muutosohjelmien tehostaminen IT-yrityksessä tietojohtamisen keinoilla

Tutkimusten mukaan suurin osa strategisista muutoshankkeista epäonnistuu. Tässä diplomityössä selvitettiin syitä epäonnistumisiin sekä kartoitettiin mahdollisuuksia tehostaa muutosjohtamista tietojohtamisen keinoilla. Lisäksi työssä laadittiin muutosjohtamisen kehittämissuositukset yhdelle tutkimuksen kohteena olleelle IT-yritykselle. Tietojohtamisen kannalta muutosjohtamista tarkasteltiin erityisesti seuraavista neljästä näkökulmasta: 1) muutostarpeiden havainnointi, 2) muutoksiin suhtautuminen, 3) luottamus ja hiljainen tieto sekä 4) muutosviestintä. Empiriaosuudessa koottiin muutosjohtamisen kokemuksia kolmesta Suomessa toimivasta IT-yrityksestä. Lisänäkemystä aiheeseen haettiin kolmelta kokeneelta muutosjohtamisen asiantuntijalta. Muutosten onnistumista vaarantavat lukuisat eri tekijät. Liiketoiminnan kauan jatkunut menestys saattaa rajoittaa muutostarpeiden havaitsemista ajoissa. Luutuneet käsitykset, luottamuksen puute ja päättäjien liian vallitsevat henkilökohtaiset näkemykset estävät uusien ideoiden esiin nousemista. Muutosjohtaminen vaatii päivittäisestä johtamisesta poikkeavia erityisosaamisia. Lisäksi henkilöstön muutosvastarinta ja muutosprosessin haasteellisuus nostavat epäonnistumisen todennäköisyyttä. Tämän tutkimuksen mukaan tietojohtamisen keinoilla on mahdollisuus tehostaa muutosjohtamista. Organisaation hiljaisen tiedon saattaminen yhteiseen käyttöön edistää sekä muutostarpeiden tunnistamista että muutoshankkeiden läpivientiä. Muutosjohtamiskoulutuksella ja tiedon tehokkaalla jakamisella parannetaan henkilöstön muutosvalmiuksia ja pienennetään muutosvastarintaa. Yhtenäisellä muutosprosessilla tehostetaan muutosten läpivientiä. Muutosmyönteisen organisaatiokulttuurin luomisella on keskeinen rooli muutosvalmiuksien kehittämisessä. Muutosvision luomisella sekä laadukkaalla ja muutosviestinnällä luodaan turvallisuuden tunnetta ja varmistetaan huomion pysyminen muutoksen tavoitteiden kannalta oikeissa asioissa.

Production of a product similar to gelatin from chicken feet collagen

Chicken feet can be used as an alternative source of collagen for the development of new products. In this sense, the aim of this study was the production of a product similar to gelatin from collagen extracted from chicken feet and the evaluation of sensory quality. The products were produced in two distinct flavors, with grape flavor called GU and pineapple flavor called GA. Subsequently, we compared these formulations with gelatin of a trademark established in the market. We used in the verification of sensory acceptability of products a hedonic scale of 9 points and the availability of consuming the product by 30 untrained tasters. According to the results, all formulations showed good levels of acceptability, indicating the collagen from chicken feet as an alternative source of high quality in the production of gelatin.

Soursop seedlings: biomasses and biometric relations in different farming environments and substrates – Part II

ABSTRACT The quality of seedling is critical to obtain vigorous plants in the field. The present study aimed to assess biomasses and biometric relations of soursop seedlings. We used different substrates in protected environments. The experiment was performed at the Universidade Estadual do Mato Grosso do Sul (UFMS) (State University of Mato Grosso do Sul). Five farming environments were developed in greenhouses: one covered with low-density polyethylene film (LDPE), another with with polyethylene and heat-reflective cloth under film under 50% shading in aluminized color, monofilament cloth under 50% shading in black, thermo-reflective cloth under 50% shading in aluminized color, and an environment covered with bacuri coconut straw. Substrates were made of manure, humus, cassava branches and vermiculite at different proportions. Each of them varying from 25%, 33.3%, 50% and 75% in mixture combination. Each environment was considered an experiment. A completely randomized design was adopted and later a joint analysis of them. Agricultural greenhouse covered with LDPE and thermo-reflective cloths under 50% of shading, proportionated seedlings with greater biomass. Substrates containing manure are the most suitable for soursop seedlings. High percentages of earthworm humus produce low quality soursop seedlings. Soursop seedlings had a Dickson’s quality index around 0.335. The greenhouse covered only with LDPE film did not produce high quality seedlings.

Ammattikorkeakoulu innovatiivisena oppimisyhteisönä

Ammattikorkeakoulut ovat osa suomalaista innovaatiojärjestelmää. Niiden tärkeimpiä tuotteita ovat laadukkaat tutkinnot, joilla tuotetaan Suomen kilpailukyvyn kannalta olennaista osaavaa työvoimaa. Koulutusinnovaatioiden avulla ammattikorkeakoulut voivat parantaa opetuksen ja oppimisen laatua ja edistää opiskelijoiden parempaa osaamista. Tässä tutkimuksessa tarkasteltiin Kymenlaakson ammattikorkeakoulua innovatiivisena oppimisyhteisönä Hokkasen (2001) hahmotteleman innovatiivisen oppimisyhteisön profiilitekijöiden mukaisesti. Tutkimuksen tavoitteena oli selvittää, millainen innovatiivinen oppimisyhteisö KyAMK:ssa toteutuu opettajien kokemana, ja miten innovatiivisen oppimisyhteisön piirteitä voitaisiin edistää mainitussa organisaatiossa. Aineisto kerättiin haastattelemalla kymmentä KyAMK:n Tekniikan ja liikenteen toimialan opettajaa. Tulokset osoittivat Kymenlaakson ammattikorkeakoulun johdon sallivan innovatiiviset koulutuksen kehittämiseen tähtäävät toimet, mutta johto ei proaktiivisesti ohjannut ja kannustanut niihin. Ammattikorkeakouluopettajien pedagogisen autonomian todettiin olevan suurta. Tästä huolimatta kaivattiin yhteisöllisyyteen tukevia toimintamalleja, joiden avulla organisaatiossa oleva monialaisen työyhteisön innovaatiopotentiaali voitaisiin valjastaa opetuksen kehittämiseen ja organisaatiolta puuttuvan toiminnan kokonaiskuvan ja -ymmärryksen kehittämiseen. Osana yhteisöllisyyden kehittämistä aineistosta nousi esiin kehittämisehdotuksena pitkäjänteisemmän verkostoitumisen toteuttaminen niin organisaation sisällä kuin ulkopuolisten sidosryhmien kanssa.

Business Intelligencen hyödyntäminen autoalan liiketoiminnassa

Tämän pro gradu -tutkielman tavoitteena on selvittää, miten Business Intelligencea voidaan hyödyntää autoalan liiketoiminnassa Suomessa. Työssä tutkitaan erityisesti autoalan tietotarpeita, tietolähteitä, tiedon analysointia sekä tiedon hyödynnettävyyttä liiketoiminnan ohjaamisessa ja päätöksenteossa. Työn tutkimusstrategiana käytettiin tapaustutkimusta, jonka kohderyhmänä oli viisi suomalaista autoalan suuryritystä. Tutkimuksen empiirinen aineisto hankittiin haastattelemalla yritysten Business Intelligence -toiminnoista vastaavia henkilöitä. Tutkimuksen tulosten perusteella Business Intelligence merkitsi yrityksille ensisijaisesti toiminnanohjausta ja sen seurantaa, sekä korkealaatuisen tiedon tuottamista päätöksentekoa varten. Keskeisiksi tietotarpeiksi luokiteltiin asiakkaisiin, ajoneuvoihin, sisäisiin prosesseihin, liiketoimintatapahtumiin, kilpailijoihin, toimialaan ja asiakastyytyväisyyteen liittyvät tiedot. Tutkimuksen tulosten perusteella tiedon hankinnassa tulee huomioida sekä sisäisen liiketoimintatiedon analyyttinen hyödyntäminen että systemaattinen tiedon hankinta myös ulkoisista lähteistä. Yritykset kokivat Business Intelligence -toimintojen parantaneen tiedon laatua, tehostaneen toiminnanohjausta sekä mahdollistaneen yhteneväisen liiketoiminnan johtamisen organisaation eri tasoilla.

Palveluliiketoimintamallin kehittäminen teolliselle laitetoimittajalle

Tässä tutkimuksessa käsitellään teollisuuden palveluliiketoimintaa. Yritykset ovat perinteisesti saavuttaneet kilpailuetua markkinoilla tuottamalla teknisesti innovatiivisia koneita ja laitteita, mutta viime vuosien aikana yritykset ovat havainneet tarpeen myös palveluliiketoiminnan kehitykselle. Kohdeyrityksenä on teollisuudelle korkealuokkaisia mittalaitteita kehittävä ja valmistava yritys. Tutkimuksen tarkoituksena oli kehittää uusi innovatiivinen vuokraukseen perustuva palveluliiketoimintamalli perinteisen hankinnan sijaan. Olennaisena osana uuteen palveluliiketoimintamalliin liittyi myös tuotteen elinkaarikustannusten selvittäminen ja laskeminen. Toisena tutkimuksen kohteena oli selvittää semi-kvalitatiivisen kyselytutkimuksen avulla, miten yrityksen asiakkaat ja henkilökunta näkevät palveluiden tuottamisen nykytilan ja mitä haasteita palveluliiketoimintaan siirtyminen aiheuttaa organisaatiolle. Työn teoriaosuudessa käsiteltiin palveluliiketoimintaa eri näkökulmista, palvelun laadun muodostumista sekä uuden liiketoimintamallin kehittämistä Osterwalderin Canvas mallin avulla. Lisäksi käsiteltiin elin-kaarilaskennan soveltamista palveluliiketoiminnassa sekä eri investointimalleja teollisiin palveluihin. Kyselytutkimuksen tulosten perusteella asiakkaiden ja yrityksen henkilökunnan näkemykset erosivat palvelun laadun ja prosessien nykytilasta. Asiakkaat arvostivat palvelut paremmalle tasolle kuin henkilökunta. Tulosten perusteella yrityksen olisi kohdennettava resursseja sisäisten prosessien parantamiseen ja kehitettävä organisaatiota enemmän palveluorientoituneeksi. Tuotteen elinkaarikustannukset onnistuttiin selvittämään hyvin ja niiden avulla pystyttiin luomaan sekä yritykselle kannattava että asiakkaille houkutteleva palveluliiketoimintamalli, jonka avulla yrityksen on mahdollista palvella asiakkaitaan entistä paremmin.

Software Development Process Modeling. Developers Perspective to Contemporary Modeling Techniques

Formal software development processes and well-defined development methodologies are nowadays seen as the definite way to produce high-quality software within time-limits and budgets. The variety of such high-level methodologies is huge ranging from rigorous process frameworks like CMMI and RUP to more lightweight agile methodologies. The need for managing this variety and the fact that practically every software development organization has its own unique set of development processes and methods have created a profession of software process engineers. Different kinds of informal and formal software process modeling languages are essential tools for process engineers. These are used to define processes in a way which allows easy management of processes, for example process dissemination, process tailoring and process enactment. The process modeling languages are usually used as a tool for process engineering where the main focus is on the processes themselves. This dissertation has a different emphasis. The dissertation analyses modern software development process modeling from the software developers’ point of view. The goal of the dissertation is to investigate whether the software process modeling and the software process models aid software developers in their day-to-day work and what are the main mechanisms for this. The focus of the work is on the Software Process Engineering Metamodel (SPEM) framework which is currently one of the most influential process modeling notations in software engineering. The research theme is elaborated through six scientific articles which represent the dissertation research done with process modeling during an approximately five year period. The research follows the classical engineering research discipline where the current situation is analyzed, a potentially better solution is developed and finally its implications are analyzed. The research applies a variety of different research techniques ranging from literature surveys to qualitative studies done amongst software practitioners. The key finding of the dissertation is that software process modeling notations and techniques are usually developed in process engineering terms. As a consequence the connection between the process models and actual development work is loose. In addition, the modeling standards like SPEM are partially incomplete when it comes to pragmatic process modeling needs, like light-weight modeling and combining pre-defined process components. This leads to a situation, where the full potential of process modeling techniques for aiding the daily development activities can not be achieved. Despite these difficulties the dissertation shows that it is possible to use modeling standards like SPEM to aid software developers in their work. The dissertation presents a light-weight modeling technique, which software development teams can use to quickly analyze their work practices in a more objective manner. The dissertation also shows how process modeling can be used to more easily compare different software development situations and to analyze their differences in a systematic way. Models also help to share this knowledge with others. A qualitative study done amongst Finnish software practitioners verifies the conclusions of other studies in the dissertation. Although processes and development methodologies are seen as an essential part of software development, the process modeling techniques are rarely used during the daily development work. However, the potential of these techniques intrigues the practitioners. As a conclusion the dissertation shows that process modeling techniques, most commonly used as tools for process engineers, can also be used as tools for organizing the daily software development work. This work presents theoretical solutions for bringing the process modeling closer to the ground-level software development activities. These theories are proven feasible by presenting several case studies where the modeling techniques are used e.g. to find differences in the work methods of the members of a software team and to share the process knowledge to a wider audience.

Electrocoagulation in the treatment of industrial waters and wastewaters

Chemical coagulation is commonly used in raw water and wastewater treatment plants for the destabilisation of pollutants so that they can be removed in the subsequent separation processes. The most commonly used coagulation chemicals are aluminium and iron metal salts. Electrocoagulation technology has also been proposed for the treatment of raw waters and wastewaters. With this technology, metal cations are produced on the electrodes via electrolysis and these cations form various hydroxides in the water depending on the water pH. In addition to this main reaction, several side reactions, such as hydrogen bubble formation and the reduction of metals on cathodes, also take place in the cell. In this research, the applications of electrocoagulation were investigated in raw water treatment and wastewater applications. The surface water used in this research contained high concentrations of natural organic matter (NOM). The effect of the main parameters – current density, initial pH, electric charge per volume, temperature and electrolysis cell construction – on NOM removal were investigated. In the wastewater treatment studies, the removal of malodorous sulphides and toxic compounds from the wastewaters and debarking effluents were studied. Also, the main parameters of the treatment, such as initial pH and current density, were investigated. Aluminium electrodes were selected for the raw water treatment, whereas wastewaters and debarking effluent were treated with iron electrodes. According to results of this study, aluminium is more suitable electrode material for electrocoagulation applications because it produces Al(III) species. Metal ions and hydroxides produced by iron electrodes are less effective in the destabilisation of pollutants because iron electrodes produce more soluble and less charged Fe(II) species. However, Fe(II) can be effective in some special applications, such as sulphide removal. The resulting metal concentration is the main parameter affecting destabilisation of pollutants. Current density, treatment time, temperature and electrolysis cell construction affect the dissolution of electrodes and hence also the removal of pollutants. However, it seems that these parameters have minimal significance in the destabilization of the pollutants besides this effect (in the studied range of parameters). Initial pH and final pH have an effect on the dissolution of electrodes, but they also define what aluminium or iron species are formed in the solution and have an effect on the ζ-potential of all charged species in the solution. According to the results of this study, destabilisation mechanisms of pollutants by electrocoagulation and chemical coagulation are similar. Optimum DOC removal and low residual aluminium can be obtained simultaneously with electrocoagulation, which may be a significant benefit of electrocoagulation in surface water treatment compared to chemical coagulation. Surface water treatment with electrocoagulation can produce high quality water, which could be used as potable water or fresh water for industrial applications. In wastewater treatment applications, electrocoagulation can be used to precipitate malodorous sulphides to prevent their release into air. Technology seems to be able to remove some toxic pollutants from wastewater and could be used as pretreatment prior to treatment at a biological wastewater treatment plant. However, a thorough economic and ecological comparison of chemical coagulation and electrocoagulation is recommended, because these methods seem to be similar in pollutant destabilisation mechanisms, metal consumption and removal efficiency in most applications.

Is there a role for pyloric exclusion after severe duodenal trauma?

Duodenal trauma is an infrequent injury, but linked to high morbidity and mortality. Surgical management of duodenal injuries is dictated by: patient's hemodynamic status, injury severity, time of diagnosis, and presence of concomitant injuries. Even though most cases can be treated with primary repair, some experts advocate adjuvant procedures. Pyloric exclusion (PE) has emerged as an ancillary method to protect suture repair in more complex injuries. However, the effectiveness of this procedure is debatable. The "Evidence Based Telemedicine - Trauma & Acute Care Surgery" (EBT-TACS) Journal Club performed a critical appraisal of the literature and selected three relevant publications on the indications for PE in duodenal trauma. The first study retrospectively compared 14 cases of duodenal injuries greater than grade II treated by PE, with 15 cases repaired primarily, all of which penetrating. Results showed that PE did not improve outcome. The second study, also retrospective, compared primary repair (34 cases) with PE (16 cases) in blunt and penetrating grade > II duodenal injuries. The authors concluded that PE was not necessary in all cases. The third was a literature review on the management of challenging duodenal traumas. The author of that study concluded that PE is indicated for anastomotic leak management after gastrojejunostomies. In conclusion, the choice of the surgical procedure to treat duodenal injuries should be individualized. Moreover, there is insufficient high quality scientific evidence to support the abandonment of PE in severe duodenal injuries with extensive tissue loss.

Aggression and its Management in Adolescent Forensic Psychiatric Care

The overall goal of this study was to explore and identify good aggression management methods and on that basis to produce recommendations for aggression management in the adolescent forensic setting. The study was conducted in three phases. In Phase I, staff’s (n = 58) perception of adolescent aggressive behaviour and methods to manage it was examined. In Phase II, staff’s (n = 30) perception of treatment settings and treatment interventions available were studied. In Phase III, the effectiveness of an aggression management programme was evaluated. The data were collected during the period 2004-2007. Participants perceived adolescent aggressive behaviour in a similar way and described aggressive behaviour as being a comprehensible phenomenon. Management methods used to control aggressive situations were alike, although the practical solutions varied between the study units, especially regarding coercive methods. Staff members proposed more time and better opportunities to discuss and evaluate the aggression situation in order to improve the methods used. The treatment settings were similar in studied forensic units and interventions were primarily focused on psychological aspects, including management of aggressive behavior. A comprehensive aggression management programme proved to be effective in decreasing incidents of violence. The use of coercive methods in aggression situations decreased and injuries to the staff became less frequent. If staff members intend to apply high quality management methods in aggression situations they have to share a consistent understanding of aggressive behaviour and need to be aware of the various methods available. In addition, they should learn more about assessment methods in order to improve aggression management. International comparison of aggression, methods for managing it and service provision creates a starting point for developing equal care provision and realization within and between European countries.

Viitearkkitehtuuri Windows-sovelluksen käyttöliittymän modernisoimiseksi web-sovellukseksi

IT-järjestelmillä on tärkeä rooli organisaation liiketoiminnassa. Koska organisaation liiketoimintavaatimukset ja strategia muuttuvat ympäröivän maailman mukaan, täytyy järjestelmän arkkitehtuurin sopeutua vallitsevaan tilanteeseen sekä mahdollisiin muutoksiin lyhyellä ja pitkällä aikavälillä. Modernin web-sovelluksen arkkitehtuuri sopeutuu organisaation liiketoiminnan haasteisiin. Erityisesti hallinnolliseksi ongelmaksi organisaatiossa muodostuvat Windows-sovellukset, koska niiden ylläpito sitoo henkilöresursseja ja niiden käyttökonteksti on rajallinen. Tästä syystä organisaatiot ovat käyneet etsimään ratkaisuja kuinka korvata Windows-sovellukset web-sovelluksilla. Kustannustehokas ratkaisu on modernisoida Windows-sovelluksen käyttöliittymä web-sovellukseksi. Tämän diplomityön tavoitteena oli laatia Logica Suomi Oy yritykselle viitearkkitehtuuri Win-dows-sovelluksen käyttöliittymän modernisoimiseksi web-sovellukseksi. Työ suoritettiin Proof of Concept projektissa, jossa modernisointiin Logican pääkäyttäjäsovellus. Työn tarkoituksena oli tunnistaa laajalti käytetyt arkkitehtuurimallit ja menetelmät jotka mahdollistavat modernisoinnin toteutuksen. Lisäksi tarkoitus oli tunnistaa menetelmät ja ohjelmistot jotka mahdollistavat kustannustehokkaan ja laadukkaan web-sovelluksen kehittämisen ja toteuttamisen. Työn osatavoitteena oli laatia modernisoitavan pääkäyttäjäsovelluksen kokonaisarkkitehtuuri. Työn tuloksena saatiin viitearkkitehtuuri jota voidaan käyttää ja hyödyntää ohjelmistokehitysprojekteissa, asiakkaan dokumentaatiossa, myynnissä ja markkinoinnissa. Viitearkkitehtuurissa on esitelty modernit web-teknologiat joilla on mahdollista toteuttaa web-sovellus jonka käyttökokemus vastaa Windows-sovellusta. Lisäksi tuloksena saatiin pääkäyttäjäsovelluksen kokonaisarkkitehtuuri, jonka tärkeimpiä tuloksia ovat modernisoinnin tavoitetila ja sovellusarkkitehtuuri. Tärkeimpiä jatkotoimenpiteitä ovat viitearkkitehtuuriin pohjautuvan modernisointiviitekehyksen laadinta sekä modernisointiprojektin arviointiin käytettävien mittareiden määrittely, suunnittelu ja toteutus. Relevanttien mittareiden avulla voidaan todeta, vastaako modernisoitu sovellus organisaation liiketoimintavaatimuksia ja strategiaa.

Liquid transportation and distribution during (re)wetting : impact on coated papers in printing

In many industrial applications, such as the printing and coatings industry, wetting of porous materials by liquids includes not only imbibition and permeation into the bulk but also surface spreading and evaporation. By understanding these phenomena, valuable information can be obtained for improved process control, runnability and printability, in which liquid penetration and subsequent drying play important quality and economic roles. Knowledge of the position of the wetting front and the distribution/degree of pore filling within the structure is crucial in describing the transport phenomena involved. Although exemplifying paper as a porous medium in this work, the generalisation to dynamic liquid transfer onto a surface, including permeation and imbibition into porous media, is of importance to many industrial and naturally occurring environmental processes. This thesis explains the phenomena in the field of heatset web offset printing but the content and the analyses are applicable in many other printing methods and also other technologies where water/moisture monitoring is crucial in order to have a stable process and achieve high quality end products. The use of near-infrared technology to study the water and moisture response of porous pigmented structures is presented. The use of sensitive surface chemical and structural analysis, as well as the internal structure investigation of a porous structure, to inspect liquid wetting and distribution, complements the information obtained by spectroscopic techniques. Strong emphasis has been put on the scale of measurement, to filter irrelevant information and to understand the relationship between interactions involved. The near-infrared spectroscopic technique, presented here, samples directly the changes in signal absorbance and its variation in the process at multiple locations in a print production line. The in-line non-contact measurements are facilitated by using several diffuse reflectance probes, giving the absolute water/moisture content from a defined position in the dynamic process in real-time. The nearinfrared measurement data illustrate the changes in moisture content as the paper is passing through the printing nips and dryer, respectively, and the analysis of the mechanisms involved highlight the roles of the contacting surfaces and the relative liquid carrier properties of both non-image and printed image areas. The thesis includes laboratory studies on wetting of porous media in the form of coated paper and compressed pigment tablets by mono-, dual-, and multi-component liquids, and paper water/moisture content analysis in both offline and online conditions, thus also enabling direct sampling of temporal water/moisture profiles from multiple locations. One main focus in this thesis was to establish a measurement system which is able to monitor rapid changes in moisture content of paper. The study suggests that near-infrared diffuse reflectance spectroscopy can be used as a moisture sensitive system and to provide accurate online qualitative indicators, but, also, when accurately calibrated, can provide quantification of water/moisture levels, its distribution and dynamic liquid transfer. Due to the high sensitivity, samples can be measured with excellent reproducibility and good signal to noise ratio. Another focus of this thesis was on the evolution of the moisture content, i.e. changes in moisture content referred to (re)wetting, and liquid distribution during printing of coated paper. The study confirmed different wetting phases together with the factors affecting each phase both for a single droplet and a liquid film applied on a porous substrate. For a single droplet, initial capillary driven imbibition is followed by equilibrium pore filling and liquid retreat by evaporation. In the case of a liquid film applied on paper, the controlling factors defining the transportation were concluded to be the applied liquid volume in relation to surface roughness, capillarity and permeability of the coating giving the liquid uptake capacity. The printing trials confirmed moisture gradients in the printed sheet depending on process parameters such as speed, fountain solution dosage and drying conditions as well as the printed layout itself. Uneven moisture distribution in the printed sheet was identified to be one of the sources for waving appearance and the magnitude of waving was influenced by the drying conditions.