Coupling coefficients of gain-coupled distributed feedback lasers with absorptive grating

An effective coupling efficient is introduced for gain-coupled distributed feedback lasers with absorptive grating. When radiation and other partial wave coupling effects are considered, the effective coupling coefficient will change significantly. In some cases, it will become real, although both loss and index coupling are presented.

Optical gain in zinc-blende GaN/Ga1-xAlxN strained quantum well laser

Based on the valence subbands of the zinc-blende GaN/Ga0.85Al0.15N strained quantum wells obtained by a 6x6 Hamiltonian (including heavy hole, light hole and spin-orbit splitting band), optical gain and radiative current density are calculated for the strained quantum well laser structures. The compressive strain in the GaN well region strongly depresses the TM mode optical gain and enhances the TE mode optical gain.

A STUDY OF THE COMPOSITION DISTRIBUTION AT THE TI/AL2O3 INTERFACE USING THE MCS(+)-SIMS TECHNIQUE

In this article, the MCs(+)-SIMS technique has been used to characterize Ti/Al2O3 metal/insulator interfaces. Our experiment shows that by detecting MCs(+) secondary ions, the matrix and interface effects are reduced, and good depth profiles have been obtained. The experimental result also shows that with the increase of the annealing temperature (RT, 300 degrees C, 600 degrees C, 850 degrees C), the interface gets broadened gradually, indicating diffusion and reaction take place at the interface, and the interface reaction is enhanced with the increase in annealing temperature. When the temperature increases, the AlCs+ signal forms two plateaus in the Ti layer, indicating Al from the decomposition of Al2O3 diffuses into the Ti layer and exists as two new forms (phases). Also, with the increase of the annealing temperature, oxygen diffuses into the Ti layer gradually, and makes the O signal in the Ti layer increase significantly in the 850 degrees C annealed sample.

5.2 GHz variable-gain amplifier and power amplifier driver for WLAN IEEE 802.11a transmitter front-end

A 5.2 GHz variable-gain amplifier (VGA) and a power amplifier (PA) driver are designed for WLAN IEEE 802.11a monolithic RFIC. The VGA and the PA driver are implemented in a 50 GHz 0.35 μm SiGe BiCMOS technology and occupy 1.12×1.25 mm~2 die area. The VGA with effective temperature compensation is controlled by 5 bits and has a gain range of 34 dB. The PA driver with tuned loads utilizes a differential input, single-ended output topology, and the tuned loads resonate at 5.2 GHz. The maximum overall gain of the VGA and the PA driver is 29 dB with the output third-order intercept point (OIP3) of 11 dBm. The gain drift over the temperature varying from -30 to 85℃ converges within±3 dB. The total current consumption is 45 mA under a 2.85 V power supply.

Gain Switch of an AlGaInP Red Light Semiconductor Laser Diode

We solve the single mode coupled rate equations by computer, simulate the behavior of a gain switch of an AlGalnP red light semiconductor laser diode, and find the characteristic of FWHM of pulses changing with the amplitude of modulation signal, the bias current, and the modulated frequency. On this basis, we conduct experiments. The experiment results accord with the simulations well.

A Broadband Long-Wavelength Superluminescent Diode Based on Graded Composition Bulk InGaAs

A novel unselective regrowth buried heterostructure long-wavelength superluminescent diode （SLD） with a graded composition bulk InGaAs active region is developed by metalorganic vapor phase epitaxy （MOVPE）. At a 150mA injection current, the full width at half maximum of the emission spectrum of the SLD is about 72nm, ranging from 1602 to 1674nm. The emission spectrum is smooth and flat. The ripple of the spectrum is less than 0.3dB at any wavelength from 1550 to 1700nm. An output power of 4.3mW is obtained at a 200mA injection current under continuous-wave operation at room temperature. This device is suitable for the applications of light sources for gas detectors and L-band optical fiber communications.

Theoretical Analysis of Gain and Threshold Current Density for Long Wavelength GaAs-Based Quantum-Dot Lasers

Quantum dot gain spectra based on harmonic oscillator model are calculated including and excluding excitons. The effects of non-equilibrium distributions are considered at low temperatures. The variations of threshold current density in a wide temperature range are analyzed and the negative characteristic temperature and oscillatory characteristic temperature appearing in that temperature range are discussed. Also,the improvement of quantum dot lasers＇ performance is investigated through vertical stacking and p-type doping and the optimal dot density, which corresponds to minimal threshold current density,is calculated.

Fabrication of semiconductor optical amplifiers and a novel gain measuring technique

The design and fabrication of 1550 nm semiconductor optical amplifiers (SOAs) and the characteristics of the fabricated SOA are reported. A novel gain measurement technique based on the integrations of the product of emission spectrum and a phase function over one mode interval is proposed for Fabry-Perot semiconductor lasers.

Structural and optical properties of GaAsSb/GaAs heterostructure quantum wells

The structural and optical properties of MBE-grown GaAsSb/GaAs multiple quantum wells (MQWs) as well as strain-compensated GaAsSb/GaAs/GaAsP MQWs are investigated. The results of double crystal X-ray diffraction and reciprocal space mapping show that when strain-compensated layers are introduced, the interface quality of QW structure is remarkably improved, and the MQW structure containing GaAsSb layers with a high Sb composition can be coherently grown. Due to the influence of inserted GaAsP layers on the energy band and carrier distribution of QWs, the optical properties of GaAsSb/GaAs/GaAsP MQWs display a lot of features mainly characteristic of type-I QWs despite the type-II GaAsSb/GaAs interfaces exist in the structure. (C) 2004 Elsevier B.V. All rights reserved.

Effects of silicon incorporation on composition, structure and electric conductivity of cubic boron nitride thin films

We have achieved in-situ Si incorporation into cubic boron nitride (c-BN) thin films during ion beam assisted deposition. The effects of silicon incorporation on the composition, structure and electric conductivity of c-BN thin films were investigated by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and electrical measurements. The results suggest that the content of the cubic phase remains stable on the whole with the incorporation of Si up to a concentration of 3.3 at.%, and the higher Si concentrations lead to a gradual change from c-BN to hexagonal boron nitride. It is found that the introduced Si atoms only replace B atoms and combine with N atoms to form Si-N bonds, and no evidence of the existence of Si-B bonds is observed. The resistance of the Si-doped c-BN films gradually decreases with increasing Si concentration, and the resistivity of the c-BN film with 3.3 at.% Si is lowered by two orders of magnitude as compared to undoped samples.