Design and testing of an armature-reaction-compensated permanent magnet synchronous generator for island operation

At present, permanent magnet synchronous generators (PMSGs) are of great interest. Since they do not have electrical excitation losses, the highly efficient, lightweight and compact PMSGs equipped with damper windings work perfectly when connected to a network. However, in island operation, the generator (or parallel generators) alone is responsible for the building up of the network and maintaining its voltage and reactive power level. Thus, in island operation, a PMSG faces very tight constraints, which are difficult to meet, because the flux produced by the permanent magnets (PMs) is constant and the voltage of the generator cannot be controlled. Traditional electrically excited synchronous generators (EESGs) can easily meet these constraints, because the field winding current is controllable. The main drawback of the conventional EESG is the relatively high excitation loss. This doctoral thesis presents a study of an alternative solution termed as a hybrid excitation synchronous generator (HESG). HESGs are a special class of electrical machines, where the total rotor current linkage is produced by the simultaneous action of two different excitation sources: the electrical and permanent magnet (PM) excitation. An overview of the existing HESGs is given. Several HESGs are introduced and compared with the conventional EESG from technical and economic points of view. In the study, the armature-reaction-compensated permanent magnet synchronous generator with alternated current linkages (ARC-PMSG with ACL) showed a better performance than the other options. Therefore, this machine type is studied in more detail. An electromagnetic design and a thermal analysis are presented. To verify the operation principle and the electromagnetic design, a down-sized prototype of 69 kVA apparent power was built. The experimental results are demonstrated and compared with the predicted ones. A prerequisite for an ARC-PMSG with ACL is an even number of pole pairs (p = 2, 4, 6, …) in the machine. Naturally, the HESG technology is not limited to even-pole-pair machines. However, the analysis of machines with p = 3, 5, 7, … becomes more complicated, especially if analytical tools are used, and is outside the scope of this thesis. The contribution of this study is to propose a solution where an ARC-PMSG replaces an EESG in electrical power generation while meeting all the requirements set for generators given for instance by ship classification societies, particularly as regards island operation. The maximum power level when applying the technology studied here is mainly limited by the economy of the machine. The larger the machine is, the smaller is the efficiency benefit. However, it seems that machines up to ten megawatts of power could benefit from the technology. However, in low-power applications, for instance in the 500 kW range, the efficiency increase can be significant.

Use of fiber-reinforced composite framework and thermochromic pigment in maxillofacial prostheses

The purpose of this investigation was to evaluate the possibility to enhance certain qualities of facial prostheses. Polymethyl methacrylate is still being used as base mate¬rial or clip carrier material, but it is hard and heavy, and debonding of the silicone from the acrylic base material is a frequent problem. This thesis aims to evaluate the use of fiber-reinforced composite (FRC) as framework material for maxillofacial silicone prostheses. FRC has been used as reinforcement in removable and fixed partial dentures since the 1990s. This material is lightweight and can be fabricated to compress the margins of the prosthesis slightly, to keep it tightly against the skin during jaw movements and facial expressions. Additionally, the use of a thermochromic pigment, colorless in room temperature and red in a cold environment, was studied in order to evaluate the possibility of using this color changing pigment in facial prostheses to mimic the color change of facial skin in cold weather. The tensile bond strength between pre-impregnated, unidirectional FRC and maxillofacial silicone elastomer was studied. Three different bonding agents or primers were compared. Bond strength was improved by one of the primers and by roughening the surface. The effect of a skin compressing glass fiber-reinforced composite framework on facial skin blood flow was studied by using a face mask, constructed with a compression pad corresponding to the outer margin of a glass fiber-reinforced framework beam of a facial prosthesis. The skin blood flow of ten healthy volunteers, aged 23-25 years, was measured during touch, light, and moderate compression of the skin, by using laser Doppler imaging technique. None of the compressions showed any marked effects on local skin blood flow. There were no significant differences between blood flow during compression and at baseline. Maxillofacial silicone elastomer was colored intrinsically with conventional color pigments: a control group containing only conventional pigments was compared to two test groups with 0.2 wt% and 0.6 wt% thermochromic pigment added. The color of the material was measured with a spectrophotometer in room temperature and after storage in a freezer. The color stability of the maxillofacial silicone elastomer colored with thermo¬chromic pigment was evaluated by artificial aging. The color dif¬ference of the L* (lightness) and a* values (redness), comparing color after the samples were stored at room temperature and in a freezer (-19°C), was statistically significant for both 0.2 wt% and 0.6 wt% thermo¬chromic pigment groups. The differences in the b* values (yellowness) were statistically significant for the 0.6 wt% group. Exposure to ultraviolet (UV) radiation led to visually noticeable and statistically signifi¬cant color changes (ΔE) in all color values in both test groups. The specimens containing thermochromic pigment were very sensitive to UV radiation. In conclusion, a framework of fiber-reinforced composite can successfully be bonded to maxillofacial silicone elastomer, and a framework beam, compressing the facial skin, did not remarkably alter the skin blood flow on healthy, young adults. The thermochromic pigment showed color change in maxillofacial silicone elastomer. However, artificial aging showed that it was too sensitive to UV radiation to be used, as such, in maxillofacial prostheses.

Tietojärjestelmäinvestoinnin jälkitarkkailumalli

Tämän työn ensisijaisena tavoitteena oli kehittää tietojärjestelmähankkeiden investointiprosessia luomalla kohdeyritykseen yhtenäinen toimintatapa hankkeiden jälkitarkkailuun. Tavoiteltu muutos koskee järjestelmäinvestointien arviointiperusteita sekä niiden käyttöönoton jälkeistä seurantaa. Jälkitarkkailumalli on rakennettu tasapainotettujen mittaristojen viitekehyksestä mittaamalla onnistumista johdon, loppukäyttäjän sekä projektin näkökulmasta. Työn tuloksena on Excel -sovellus sekä toimintatapa sovelluksen käytölle. Esimerkki-investoinnista kerätyn kokemuksen perusteella malli tukee investointiin liittyvien sidosryhmien sitoutumista yhteisiin tavoitteisiin sekä selkeyttää roolijakoa IT - vetoisen projektiryhmän ja yrityksen liiketoiminnallisen johdon välillä. Lisäksi mallin koettiin tukevan käyttöönotetun järjestelmän tavoitelähtöistä johtamista. Käytön laajentuessa mallilla uskotaan olevan yksittäistenhankkeiden lisäksi positiivinen vaikutus myös yrityksen tietojärjestelmähankkeiden investointiprosessiin.

Uusien energianormien vaikutus pientalojen rakenteisiin ympäristön kannalta

Tehokkaimpia keinoja vähentää rakennusten lämmitysenergian kulutusta ja lämmityksen aiheuttavia hiilidioksidi- ja happamoitavia päästöjä on tiukentaa rakentamismääräysten lämmöneristysvaatimuksia. Hyvin lämmöneristetyissä, tiiveissä ja ilmanvaihdoltaan optimoiduissa taloissa on pienet lämpöhäviöt. Näin ympäristöä kuormittava vaikutus saadaan paljon vähemmäksi kuin nykynormien mukaisissa asuinrakennuksissa. Johtumislämpöhäviö pienenee suoraan eristekerroksia paksuntamalla ja siihen on helpointa vaikuttaa. Mitä suurempiin eristepaksuuksiin mennään sen suuremmaksi tulee konvektion osuus kokonaislämpöhäviöstä. Tulevaisuudessa parempia ratkaisuja haetaan erityisesti konvektiosta ja säteilystä aiheutuvien lämpöhäviöiden pienentämiseksi. Eristeen osastointi ilmanpitävillä, vesihöyryä diffuusisesti läpäisevillä pystysuuntaisilla konvektiokatkoilla vähentää tehokkaasti paksun seinäeristeen kuljettumis-ilmavirtauksia. Katkoina käytetään erilaisia kalvoja ja rakennuspapereita, joilla on pieni emissiviteetti. Katkojen merkitys kasvaa, kun mennään uusien normien mukaisiin eristepaksuuksiin. Lämmöneriste voidaan toteuttaa myös kokoamalla ohuita kalvoja paketiksi, jotka jakavat ilmatilan ja siis eristeelle varatun paksuuden suljettuihin ilmaväleihin. Kun kalvoiksi valitaan pieniemissiviteettisiä pintoja, saadaan säteilylämmönsiirto lähes eliminoiduksi. Tällaisen ilmatilan lämmönjohtumisluku lähestyy paikallaan pysyvän ilman lämmönjohtumislukua, l = 0,025 W/Km, eli tällä rakennesysteemillä on mahdollista toteuttaa ohuempia rakenteita kuin perinteisillä eristeillä. Hygroskooppisen massan käyttö sisäilman kosteutta tasaavana rakenteena voi olla tulevaisuutta. Kehitystyö tuottaa uusia, kosteusteknisesti toimivia sovelluksia. Toisaalta palomääräykset tulevat kehitystyötä vastaan. Hygroskooppinen pintamateriaali on kevyt (pieni tiheys) ja paloteknisesti arka. Suoraa sähkölämmitystä ei voida pitää ympäristöystävällisenä. Sen jalostusketju on pitkä ja monivaiheinen. Millä peruspolttoaineella sähköä tuotetaan, vaikuttaa asiaan luonnollisestikin. Suoraa sähkölämmitystä voidaan suositella vain yksinäisen ihmisen taloudessa lämmitysmuotona taloudellisista syistä. Halvan polttoaineen säästöllä ei voida maksaa suuria laiteinvestointeja. Aurinkoenergian hyvä hyödyntäminen edellyttää hyvää säätöä, joka kytkee lämmityksen pois päältä silloin, kun aurinko lämmittää. Auringon hetkelliset säteilytehot ovat suuria verrattuna rakenteen lämpöhäviöihin ja huonetilojen lämmöntarpeeseen. Ratkaisu aurinkoenergian hetkellisyyteen ja paikallisuuteen on energian siirtäminen lämmöntarpeen mukaan rakennuksen eri osiin ja sen varastoiminen päivätasolla. Kun varastoivasta massasta ei ole suoraa yhteyttä ulos, voidaan kerääjäeristeeltä saatu lämpö käyttää häviöttömästi huonetilojen lämmittämiseen. Vaikka lämmitysenergian käytössä päästään 30 % vähennyksiin uudisrakennusten osalta, ei kokonaisenergian käyttö merkittävästi pienene, jos taloussähkön kulutus pysyy vakiona. Sama pätee myös CO2 -päästöihin. Saavutettava etu lämmitys-energian kulutuksessa voidaan hukata yhä suurenevaksi taloussähkön käytöksi, mikä olisi erityisen huono asia ympäristön kannalta.

Strateginen laskentatoimi strategisen johtamisprosessin tukena. Case: SOK-yhtymän kiinteistötoiminnot

Tämän tutkielman päätavoitteena on tutkia niitä menetelmiä, joilla johdon laskentatoimi tukee strategista johtamista ja selvittää kuinka laskentatointa hyödynnetään strategisessa johtamisprosessissa. Empiirisessä osuudessa analysoidaan SOK-yhtymän kiinteistötoimintojen laskentatoimen ja strategisen johtamisprosessin välistä yhteyttä. Tavoitteena on parantaa tämän tutkimuksen avulla laskentatoimen hyödyntämistä strategisessa johtamisessa. Tutkimusongelman ratkaisemiseksi selvitetään seuraavat aihealueet, niiden selvittämisestä muodostuvat myös tämän tutkimuksen osatavoitteet. Ensimmäisenä osatavoitteena on selvittää doktriiniin perustuen, mistä strategisessa johtamisessa ja johdon strategiaprosessissa on kysymys. Toisena osatavoitteena on tarkastella strategisen laskentatoimen teoriaa ja innovaatioita johdon näkökulmasta. Toisin sanoen, osatavoitteena on siis selvittää, mitä strateginen laskentatoimi on ja millaisia konkreettisia menetelmiä sillä on käytettävissään strategisen johtamisen tukemisessa. Kolmantena osatavoitteena on esitellä tutkielman empiirinen osuus, joka pohjautuu SOK-yhtymän kiinteistötoimintojen strategiseen johtamisprosessiin ja sitä tukevaan johdon laskentatoimeen. Samalla kun tutkitaan johdon toimintoja prosessin eri vaiheissa, esitetään johdon tueksi erilaisia laskennallisia menetelmiä, joista on hyötyä päätöksenteossa ja resurssien suuntaamisessa sekä strategian toteuttamiseen valvonnassa Tässä tutkimuksessa strategista johtamista ja strategista laskentatointa tarkastellaan SOK-yhtymän kiinteistötoimintojen vuoden 2001 tilanteen mukaan osana S-ryhmän ja SOK-yhtymän jatkuvaa strategiaprosessia. Näkökulma tarkastelulle on sekä ylimmän yritysjohdon, että strategisen liiketoimintajohdon.

Managing virtual project teams

The purpose of the Master’s Thesis is to study the best practices to virtual project management from the project manager’ point of view. The best practices are divided according to a five-phase virtual project life cycle model. Each phase include concrete suggestions for actions. Research’s theoretical background is wide because of the broad subject matter. In the theoretical part topics such as virtual working, virtual project management challenges are examined and some concrete actions to tackle these challenges are introduced. Thesis’ approach is constructive, where a known problem is solved piece by piece after creating a pre-understanding of the topic. Existing research work is utilized when creating a model for virtual project team management. The basis of the model comes from various best practices read from literature and from the interviews conducted on experienced virtual project managers in the case organization. As a result the model combines both previous research and the organizations empirical experience. As an output of the thesis a model for virtual project team management is developed, which can be used as a guideline by the virtual project managers in their work. The model includes actions and practices what can be used to overcome the challenges of virtual project management.

Hoitotyön opettajan yhteiskunnallinen toiminta – osa opettajuutta

The social activity of nurse teacher – a part of teacherhood Every nurse teacher must know the current health policy in order to use it in teaching. The conception of the role of health policy in curriculum and the concrete teaching of social activity are quite unclear. The purpose of this study was to describe the social activity of nurse teachers. The data were collected by a structured questionnaire (Paltta 1998) via E-mail. The questionnaire included background factors and nine items for society activities. The respondents were nurse teachers, teachers for emergency nursing, public health nurse and midwifery teachers from all polytechnics in Finland. Response rate was 46 % (n = 342). The data were analysed by using descriptive statistics. The results of this study showed that 36 % of nurse teachers evaluated themselves quite active in society activities and 43 % of them evaluated themselves inactive. 32 % of nurse teachers was member and involved to working in general organisations. 28 % of nurse teachers worked or have been worked in local commission or trustees. Nurse teachers evaluated their knowledge about health policy quite good (mean 3.75, Std 0.99). Their knowledge about education policy was also quite good (mean 3.57, Std 1.04). Nurse teachers updated their knowledge about health policy and education policy by reading professional journals, newspapers, internet and following television and radio. According to results nurse teachers are quite active in society activities even tough almost half of them evaluated themselves quite inactive. Although nurse teachers’ knowledge about health policy was quite good by their opinion, they must update and improve the knowledge. In the future it is important to study how nurse teachers use health policy in their teaching and how nurse students’ participation in society activities can be improved.

Opetuksen kehittäminen Lappeenrannan teknillisen yliopiston tuotantotalouden osastolla - työtä, leipää ja sirkushuveja

Työn tavoitteena oli koota Lappeenrannan teknillisen yliopiston tuotantotalouden osaston opetuksen kehittämisen historiatiedot ja henkilöstön mielipide vuosien 2000–2008 aikana tehdystä kehittämistyöstä organisaation jatkokehittämistä ja viestintää varten. Työn aihepiiri käsittelee organisaation kehittämistä (kehittymistä) yksilön ja organisaation oppimisen näkökulmasta. Historiatiedot on kerätty osaston henkilökunnalta ja saaduista dokumenteista. Henkilöstön palautteen kerääminen kehittämistyöstä toteutettiin laadullisena tutkimuksena suorittamalla 32 henkilökohtaista haastattelua. Tutkimuksen keskeisimmäksi tulokseksi on saatu onnistuneen kehittämisen malli, jossa yksilön ja organisaation kehittymiseen vaikuttavat vahvasti yksilötasolla tarve ja konkreettinen päämäärä. Koko organisaatiossa on lisäksi huomioitava muina osina systematiikka, yhteisöllisyys ja tietämyksen (osaamisen) hallinta.

Den etiske akten : den caritative etikken når pasientens fordringer er av eksistensiell art

The purpose of this thesis is to develop a theory model about some core concepts and phenomena within caritative ethics when patients' demands are existential. There are two research questions, (A) Which realities represent concepts such courage, responsibility, and sacrifice within the caritative ethics. (B) Which phenomena of ethical significance are made current and applicable when patients¿ demands are existential. This study takes as its point of departurecertain chosen theoretical perspectives that discuss some perspectives of the concepts of courage, responsibility, and sacrifice in terms of their significanceto the research questions A. This represents the study¿s theoretical data. The empirical data provide answers to the research question B. In the end, the thesis discusses synthesis of these two accesses of knowledge in order to formulate theses and create a theory model. Løgstrup's contribution and description of the ethical claim helps in understanding and interpreting the links between the substance of the caritative ethic and the concrete reality in the encounter with existential issues. This thesis is a study within the field of Caring Science. The nursing profession provides empirical data and reflects the study topic, by addressing issues of relevance to the application of the knowledge of Caring Sciencein light of the nursing profession's various daily challenges. This study proceeds from the basic assumption: "Caring relationships form the meaningful contextfor caring and derive from the ethos of love, responsibility, and sacrifice, i.e. a caritative ethics" (Eriksson 2001). This study attempts to explore and prove this statement in the light of theoretical and empirical data, in the light ofthe caring scientific perspective which is here linked particularly to the viewof man as a unity of body, mind, and soul, and to the ontological health model. Hermeneutics is the overall perspective for the interpretations proposed in this thesis. Through conversation and hermeneutic observations, I try to understandthe challenges of nursing performance in the encounter with existential issues. This constitutes the empirical data that was gathered on a ward treating cancerpatients. The discussion proceeds sequence by sequence, first by discussing theconditions of the caritative ethics when meeting the existential claims in the light of the concepts of courage, sacrifice, and responsibility. Then a thesis is formulated concerning the caritative ethics in the light of Caring Science. This is the foundation of the creation of the theory model. The resulting theses concern the chosen concepts and phenomena which promote caritative ethics when patients' claims are existential: Freedom is the hallmark of caritative ethics. Freedom is the basic category of caring. When attending to the patient's existential claims, it is of vital importance to secure human relationships as caring interpersonal communions, created by responsible persons who have shown courage and sacrifice. Courage and sacrifice constitute the ethos of caring communities (communions). Courage and sacrifice are then a part of the collective ethos of caring communities, because the patient is confirmed as the unity of body, mind, and soul.

The Process of Greening Cycle as Method of Operative Environmental

The structural change of society from product-based business to service- and further to need-based business has caused the fact that work for environmental issues has spread from conventional factories and environmentally harmful production to concern services and offices as well. Almost every company has an office, so a relatively small environmental burden caused by an individual office grows remarkable already at the state level and globally even more. Motivation to work for environmental issues in an individual office could be challenging even without the fact that wasted environmental impacts bound also wasted costs. Besides cost savings, a concretely greener image of a company has its value in the B2Cas well as in the B2B-field. Consumers and clients are more and more conscious of environmental issues and demand concrete actions instead of speeches, good thoughts and meaningless certifications. Internal work for environmental issues at a strategy level is not sufficient, so operational environmental management is needed for changing old practices. This research is about the effects of operative environmental management on the greening process of an office-based business. The research is outlined to concern the operative work in the office including field sales. Target was to concretely lower the environmental impacts of Lyreco Finland and to find cost savings directly by changing the operative practices in the office and also indirectly by affecting the level of environmental knowledge of the personnel. During the greening process, the aim was also to create concrete arguments for marketing as well. The circle of greening process, which was especially created for this diploma work, was used as a method. The circle divides a year to themes and sections separated by factors of environmental impacts. Separation is based on Brett Wills’ thoughts of seven green wastes (Wills, Brett. The Green Intensions. 2009) and follows it uneasily. The circle aimed at ensuring evolutionary growth of knowledge instead of being revolutionary in the changing process. Committing personnel to the process from its start by asking ideas from them and giving them clear directions was an important part of the research of operative management. Because of working from distance, communication with personnel was operated by frequent training days and weekly greening notes via emails and intranet. Also availability for communication was an important task because of the telecommuting. Research results of this work show that operative environmental management in an officebased business today is mostly management of change. When the strategic environmental friendliness is taken into a concrete level, the most important individual factor is motivating the operating personnel. Research shows that evolutionary change is found being an efficient way to make a change. Also understanding one´s own impact on the environmental burden and on the whole greening process clearly motivates the personnel. Results show that in the operative realization of the greening process, clear directions of new working practices, being as concrete as possible, and committing personnel to follow them make the process more effective. The operative environmental management and the cycle of the greening process decrease the environmental burden and save costs. The concrete results could be used as believable arguments in marketing and therefore exploited in communication with interest groups. Commitment of the management is also one of the key factors of success in the greening process. In this research, changes in the business field by a company trade took the focus of the management away from the greening process and made the process more inefficient by decreasing the amount of training days. The circle of greening process will be used as a tool in the future, as well, and therefore it will help observe environmental impacts of a company and increase sustainable development. Commitment of management to the evolutionary environmental work helps the operating personnel lower environmental impacts, decrease costs and build a concretely greener image.

Varastonhallinnan ja tuotannonsuunnittelun kehittäminen paperitehdasympäristössä

Tämän diplomityön tavoitteena on kehittää erään paperitehtaan käyttöpääoman hallintaa tuotannonsuunnittelun ja varastonhallinnan keinoin. Tuotannonsuunnittelussa tutkitaan syklinpituuden vaikutusta lajinvaihtohylkyyn ja siitä aiheutuvan varastotason nousun hyötyjä ja haittoja. Tehtaan ylijäämätasot määritetään puolen vuoden aikajänteeltä ja pyritään löytämään kehitysehdotuksia niiden minimoimiseksi. Työssä keskitytään lisäksi satamasta palautettuihin rulliin ja haamurulliin. Työn aiheista tehdään nykytila-analyysit, joiden perusteella selvitetään kehityskohteet. Työssä hyödynnetään tehtaan omia tietojärjestelmiä osa-alueiden analysoimisessa. Analysoimisessa käytetään karkeasuunnitelmaa ja erilaisia raportteja varastoihin ja tuotantoon liittyen. Työn tulosten mukaan voidaan todeta, että syklinpituutta ei kannata varasto-ohjautuvalla tuotantomuodolla kasvattaa. Ylijäämiä syntyy paperiteollisuudessa vääjäämättä ja kyseisessä yrityksessä niiden hyödyntämisprosentit ovat varsin korkealla tasolla. Kokonaisuutena tehtaan käyttöpääoman hallinta on varsin hyvällä pohjalla eikä suuria toimintatapamuutoksia ole tarpeen tehdä. Satamapalautusongelman suuruudesta tehtaalla oli erilainen käsitys kuin asia todellisuudessaan oli. Työssä esitetään kehitysehdotuksia, joiden avulla ongelmaa voidaan edelleen pienentää ja saavuttaa konkreettisia säästöjä. Haamurullien määrä osoittautui minimaaliseksi.

Ydinprosessikuvaus johtamisen tukena rakennusalan konsernissa

Tämän diplomityön tärkeimpänä tavoitteena on kuvata kohdekonsernin ydinprosessi asiakasrajapinnasta takuutarkastukseen sekä sitä tukevat prosessit riittävällä tarkkuudella. Lisäksi tavoitteena on laatia kuvaamisen pohjalta yksinkertainen työkalu yksittäisten hankkeiden johtamisen sekä sisäisen koulutuksen tarpeisiin. Tavoitteena on työn kautta edistää konsernin strategisten tavoitteiden saavuttamista. Työ jakautuu teoria- ja empiriaosaan. Teoriaosassa luodaan viitekehys työn empiriaosalle. Se pitää sisällään prosessiajattelun ja prosessijohtamisen käsittelyä sekä prosessien kuvaamisen ja niiden suorituskyvyn mittaamisen teoreettista taustaa. Työn empiria- eli käytännön osassa kuvataan konsernin strategian mukainen ydinprosessi ja määritetään siihen porttimallin mukaiset portit sekä niissä tarkastettavat minimivaatimukset. Lisäksi esitellään ydinprosessia tukevia prosesseja ja laaditaan suorituskykymittaristo sekä käsitellään jatkuvaa parantamista konsernissa käytännössä. Käytännön osan lopussa esitellään kuvauksen pohjalta laadittu työkalu sekä sen tuomat mahdollisuudet. Teoriaosa on luonteeltaan kirjallisuustutkimus, joka muodostuu kirjojen ja artikkelien pohjalta. Empiriaosassa on sekä tapaustutkimuksen että konstruktiivisen tutkimuksen piirteitä ja menetelminä siinä on käytetty haastatteluja, palavereita ja havainnointia. Empiriaosassa on hyödynnetty myös konsernin omaa aineistoa. Keskeisimpiä tuloksia ovat ydinprosessin kuvaus sekä sen pohjalta laadittu konsernin tarpeisiin vastaava konkreettinen työkalu. Lisäksi tuloksena voidaan pitää havaittua prosessiajattelun edistymistä konsernissa. Kohdekonsernin ydinprosessi koostuu kuudesta vaiheesta: 1) asiakastarpeiden selvitys/myynti, 2) tarjous- ja sopimusvaihe, 3) suunnittelu, 4) työmaavaihe, 5) ennakkotarkastus- ja luovutusvaihe ja 6) loppuselvitys- ja takuuvaihe. Ydinprosessin vaiheet muodostuvat määriteltyjen porttien kautta ja ne muodostavat konsernin prosessikartan rungon.

Replacing Copper with New Carbon Nanomaterials in Electrical Machine Windings

Electrical machines have significant improvement potential. Nevertheless, the field is characterized by incremental innovations. Admittedly, steady improvement has been achieved, but no breakthrough development. Radical development in the field would require the introduction of new elements, such that may change the whole electrical machine industry system. Recent technological advancements in nanomaterials have opened up new horizons for the macroscopic application of carbon nanotube (CNT) fibres. With values of 100 MS/m measured on individual CNTs, CNT fibre materials hold promise for conductivities far beyond those of metals. Highly conductive, lightweight and strong CNT yarn is finally within reach; it could replace copper as a potentially better winding material. Although not yet providing low resistivity, the newest CNT yarn offers attractive perspectives for accelerated efficiency improvement of electrical machines. In this article, the potential for using new CNT materials to replace copper in machine windings is introduced. It does so, firstly, by describing the environment for a change that could revolutionize the industry and, secondly, by presenting the breakthrough results of a prototype construction. In the test motor, which is to our knowledge the first in its kind, the presently most electrically conductive carbon nanotube yarn replaces usual copper in the windings.

Facilitating corporate entrepreneurial behavior: A study of corporate entrepreneurial behavior in corporate banking

This study discusses the pronounced importance of corporate entrepreneurial behavior, CEB, facilitation and enablement as a key dimension in the rapidly changing business environment within companies. The research target is a large finance company in Finland, where regulations, compliance and processes restrict and refine extensively business approach. The purpose of this study is to foster the understanding of corporate entrepreneurial behavior and requirements and identify the supporters and inhibitors of facilitation of it. Furthermore, this study examines who should be driving the implementation and offer concrete outcome for the company to get the facilitation started and berth it as part of the organizational culture and values. The theoretical background is constructed from literature related to concept of corporate entrepreneurial behavior, factors supporting and hindering the facilitation based on previous studies and innovation management. Furthermore theoretical framework of middle managers entrepreneurial behavior in facilitation process was researched. Additionally top down and bottom up approach of conversational space building within the organization in order to foster innovation and involving mindset and behavior was in the core literature. The empirical research conducted for the study consists three parts; innovation audit questionnaire, semi-structured interviews and secondary data from previously made research within the case company. Questionnaire and interviews were targeted to eight middle managers within the company, the head of branch regions in corporate segment. The secondary data was collected from over 300 employees in the case company by an external company. Research results were analyzed mainly by themes and source division in adaption with the theoretical framework. The study finds that facilitation of CEB should be a strategic choice and requires strong management support and examples. Behavior should be involved with organizational culture, values, structures and processes. The companies´ willingness to take risks and encourage employees at all levels to participate and be involved by taking ownership and responsibility is in the core. CEB is found to be a key dimension in increasing employee satisfaction and engagement, competitive advantages and economic growth of companies. There is increased interest towards CEB in the case company but there is lack in the mutual consensus of it. CEB is not in the strategy although the mindset and support from management is in place. There is no concrete enablement and space for innovation and CEB although the platform would be receptive. Further research is needed to build shared vision of CEB and how to make it a part of the organizational culture and values in addition to building the conversational space.

Lightweight, liquid-cooled, direct-drive generator for highpower wind turbines: motivation, concept, and performance

Thesis: A liquid-cooled, direct-drive, permanent-magnet, synchronous generator with helical, double-layer, non-overlapping windings formed from a copper conductor with a coaxial internal coolant conduit offers an excellent combination of attributes to reliably provide economic wind power for the coming generation of wind turbines with power ratings between 5 and 20MW. A generator based on the liquid-cooled architecture proposed here will be reliable and cost effective. Its smaller size and mass will reduce build, transport, and installation costs. Summary: Converting wind energy into electricity and transmitting it to an electrical power grid to supply consumers is a relatively new and rapidly developing method of electricity generation. In the most recent decade, the increase in wind energy’s share of overall energy production has been remarkable. Thousands of land-based and offshore wind turbines have been commissioned around the globe, and thousands more are being planned. The technologies have evolved rapidly and are continuing to evolve, and wind turbine sizes and power ratings are continually increasing. Many of the newer wind turbine designs feature drivetrains based on Direct-Drive, Permanent-Magnet, Synchronous Generators (DD-PMSGs). Being low-speed high-torque machines, the diameters of air-cooled DD-PMSGs become very large to generate higher levels of power. The largest direct-drive wind turbine generator in operation today, rated just below 8MW, is 12m in diameter and approximately 220 tonne. To generate higher powers, traditional DD-PMSGs would need to become extraordinarily large. A 15MW air-cooled direct-drive generator would be of colossal size and tremendous mass and no longer economically viable. One alternative to increasing diameter is instead to increase torque density. In a permanent magnet machine, this is best done by increasing the linear current density of the stator windings. However, greater linear current density results in more Joule heating, and the additional heat cannot be removed practically using a traditional air-cooling approach. Direct liquid cooling is more effective, and when applied directly to the stator windings, higher linear current densities can be sustained leading to substantial increases in torque density. The higher torque density, in turn, makes possible significant reductions in DD-PMSG size. Over the past five years, a multidisciplinary team of researchers has applied a holistic approach to explore the application of liquid cooling to permanent-magnet wind turbine generator design. The approach has considered wind energy markets and the economics of wind power, system reliability, electromagnetic behaviors and design, thermal design and performance, mechanical architecture and behaviors, and the performance modeling of installed wind turbines. This dissertation is based on seven publications that chronicle the work. The primary outcomes are the proposal of a novel generator architecture, a multidisciplinary set of analyses to predict the behaviors, and experimentation to demonstrate some of the key principles and validate the analyses. The proposed generator concept is a direct-drive, surface-magnet, synchronous generator with fractional-slot, duplex-helical, double-layer, non-overlapping windings formed from a copper conductor with a coaxial internal coolant conduit to accommodate liquid coolant flow. The novel liquid-cooling architecture is referred to as LC DD-PMSG. The first of the seven publications summarized in this dissertation discusses the technological and economic benefits and limitations of DD-PMSGs as applied to wind energy. The second publication addresses the long-term reliability of the proposed LC DD-PMSG design. Publication 3 examines the machine’s electromagnetic design, and Publication 4 introduces an optimization tool developed to quickly define basic machine parameters. The static and harmonic behaviors of the stator and rotor wheel structures are the subject of Publication 5. And finally, Publications 6 and 7 examine steady-state and transient thermal behaviors. There have been a number of ancillary concrete outcomes associated with the work including the following. X Intellectual Property (IP) for direct liquid cooling of stator windings via an embedded coaxial coolant conduit, IP for a lightweight wheel structure for lowspeed, high-torque electrical machinery, and IP for numerous other details of the LC DD-PMSG design X Analytical demonstrations of the equivalent reliability of the LC DD-PMSG; validated electromagnetic, thermal, structural, and dynamic prediction models; and an analytical demonstration of the superior partial load efficiency and annual energy output of an LC DD-PMSG design X A set of LC DD-PMSG design guidelines and an analytical tool to establish optimal geometries quickly and early on X Proposed 8 MW LC DD-PMSG concepts for both inner and outer rotor configurations Furthermore, three technologies introduced could be relevant across a broader spectrum of applications. 1) The cost optimization methodology developed as part of this work could be further improved to produce a simple tool to establish base geometries for various electromagnetic machine types. 2) The layered sheet-steel element construction technology used for the LC DD-PMSG stator and rotor wheel structures has potential for a wide range of applications. And finally, 3) the direct liquid-cooling technology could be beneficial in higher speed electromotive applications such as vehicular electric drives.