Kompressoriyksiköiden mekaaninen kunnonhallinta

Kunnossapidon kuluista suurimman osan aiheuttavat koneiden ennakoimattomat rikkoutumiset ja niiden tuomat tuotannonpysäytykset. Kunnossapidon suunnitelmallisuutta ja vikojen ennustettavuutta pyritään parantamaan erilaisin kunnonvalvonnallisin keinoin. Havaitsemalla alkava vikaantuminen ajoissa ja seuraamalla sen kehittymistä luodaan mahdollisuus korjaustoimenpiteiden ja -ajankohdan hallittuun suunnitteluun ja tätä kautta kustannussäästöihin. Tässä työssä on tutkittu kompressoriyksiköiden (kaasuturbiini ja keskipakokompressori) ja niiden apulaitteiden kunnossapidon menetelmiä, niiden hyödynnettävyyttä sekä mahdollisuuksia kehittää mekaanista kunnonhallintaa. Työssä päädyttiin johtopäätökseen, että käytettävien menetelmien hyödynnettävyydessä on kehitettävää. Kunnonvalvonnan ohjeistuksia tarkennettiin vastaamaan tämän päivän tavoitteita. Todettiin myös, että värähtelynvalvontaan perustuva kunnonvalvontajärjestelmä soveltuu hyvin kompressoriyksiköiden kunnonvalvonnan järjestelmäksi. Värähtelynvalvontaan perustuva kunnonvalvontajärjestelmä luo mahdollisuuden turvallisen käyttöajan ennustamiseen. Kunnonvalvonnan kehittämisen ja käyttövarmuuden parantamisen kannalta jatkotutkimuksen tekeminen kompressoriyksiköiden mekaanistenlaitteiden turvallisen käyttöajan ennustamiseksi on perusteltua.

Optimizing the supply chain strategy of a multi-unit Finnish nursery company

Abstract

The Effectiveness of Currency Hedging Strategies. Case: Imatra Boards Business Unit of Stora Enso Corp.

Tutkimus tarkastelee vaihtoehtoisia termiinisuojaustrategioita metsäteollisuuden alan tulosyksikössä. Jälkitestauksen tarkoituksena on arvioida vaihtoehtoisten strategioiden tuloksellisuutta suojata case-yrityksen kassavirtoja seuraavan kolmen arviointikriteerin avulla: yksittäisten vieraan valuutan määräisten kassavirtojen vaihtelu; koko vieraan valuutan määräisen kassavirran vaihtelu; suojausvoitot ja -tappiot. Tutkimuksen teoreettinen viitekehys tarkastelee yrityksen päätöksentekoa, valuuttariskien suojausprosessia sekä esittelee yrityksen vaihtoehtoisia suojausstrategioita. Tutkimuksen empiirinen aineisto pohjautuu case- yrityksen historiallisiin myyntilukuihin ja on kerätty yrityksen tietojärjestelmästä. Muu tutkimuksessa käytetty dataon kerätty eri tietokannoista. Tutkimuksen tulokset osoittavat, että suojaaminen vähentää kassavirtojen vaihtelua. Suojaamisen taloudelliset tulokset ovat kuitenkin erittäin riippuvaisia valitusta suojausstrategiasta, joka voi johtaa merkittäviin suojausvoittoihin, mutta yhtä hyvin myos merkittäviin tappioihin. Johdon näkemykset ja riskitoleranssi määrittelevät mitä strategiaa yrityksessä tullaan viime kädessä noudattamaan.

Experimental and Numerical Analysis of Different Volutes in a Centrifugal Compressor

In a centrifugal compressor the flow around the diffuser is collected and led to the pipe system by a spiral-shaped volute. In this study a single-stage centrifugal compressor with three different volutes is investigated. The compressorwas first equipped with the original volute, the cross-section of which was a combination of a rectangle and semi-circle. Next a new volute with a fully circular cross-section was designed and manufactured. Finally, the circular volute wasmodified by rounding the tongue and smoothing the tongue area. The overall performance of the compressor as well as the static pressure distribution after the impeller and on the volute surface were measured. The flow entering the volute was measured using a three-hole Cobra-probe, and flow visualisations were carriedout in the exit cone of the volute. In addition, the radial force acting on theimpeller was measured using magnetic bearings. The complete compressor with thecircular volute (inlet pipe, full impeller, diffuser, volute and outlet pipe) was also modelled using computational fluid dynamics (CFD). A fully 3-D viscous flow was solved using a Navier-Stokes solver, Finflo, developed at Helsinki University of Technology. Chien's k-e model was used to take account of the turbulence. The differences observed in the performance of the different volutes were quite small. The biggest differences were at low speeds and high volume flows,i.e. when the flow entered the volute most radially. In this operating regime the efficiency of the compressor with the modified circular volute was about two percentage points higher than with the other volutes. Also, according to the Cobra-probe measurements and flow visualisations, the modified circular volute performed better than the other volutes in this operating area. The circumferential static pressure distribution in the volute showed increases at low flow, constant distribution at the design flow and decrease at high flow. The non-uniform static pressure distribution of the volute was transmitted backwards across the vaneless diffuser and observed at the impeller exit. At low volume flow a strong two-wave pattern developed into the static pressure distribution at the impeller exit due to the response of the impeller to the non-uniformity of pressure. The radial force of the impeller was the greatest at the choke limit, the smallest atthe design flow, and moderate at low flow. At low flow the force increase was quite mild, whereas the increase at high flow was rapid. Thus, the non-uniformityof pressure and the force related to it are strong especially at high flow. Theforce caused by the modified circular volute was weaker at choke and more symmetric as a function of the volume flow than the force caused by the other volutes.

RF Field Immunity of a Network Terminating Unit at Over One Gigaherz Frequencies

Työssä tutkitaan telepäätelaitteen yli gigahertsin taajuisen säteilevän RF kentän sietoisuutta. Mittauksissa testattava laite on Tellabs Oy:n valmistaman CTU modeemin tuotekehitysversio. Teoriaosassa käydään läpi sähkömagneettisten aaltojen teoriaa, sekä säteilevän RF kentän aiheuttamien sähkömagneettiset häiriöiden syntymekanismeja. Myös säteilevien häiriöiden EMC mittauksiin tarvittavien mittalaitteiden tärkeimmät ominaisuudet esitellään, sekä pohditaan yli gigahertsin taajuuksille sopivien EMC mittalaitteiden vaatimuksia. EMC standardit eivät tällä hetkellä aseta vaatimuksia telelaitteiden RF kentän sietoisuudelle yli gigahertsin taajuudella. Tämän vuoksi työssä käsitellään myös todennäköisimpiä häiriölähteitä tällä taajuusalueella. Mittauksissa tutkittiin CTU:n RF kentän sietoisuutta taajuusalueella l - 4.2 GHz. Mittaukset suoritettiin sekä radiokaiuttomassa kammiossa että GTEM solussa. Myös metallisten lisäsuojien vaikutusta CTU:n kentänsietoisuuteen tutkittiin GTEM solussa.

Suurnopeuskompressorin tekninen markkinoilletuonti

Diplomityössä tarkastellaan suurnopeuskompressorin kehityspolkua suurnopeusteknologian lähtökohdista prototyypiksi ja edelleen teolliseksi tuotteeksi. Työssä tarkastelun kohteena on sähköteholtaan 20….250 kW oleva, suurnopeussähkökoneella ja öljyttömillä magneettilaakereilla varustettu keskipainekompressori. Tyypillisesti kompressorin painesuhde on 1,2 … 2,4. Ko. kompressorin käyttökohteina on tarkasteltu mm. pienen kunnallisen jätevedenpuhdistamon käsittelyaltaiden ilmastusta, suuren kaupungin vastaavan puhdistuslaitoksen ilmastuskäyttöä ja teollista käyttöä lasivillatehtaan ns. linkokompressorina. Suurnopeuskompressori soveltuu hyvin rinnankytkentään ns. ryhmäohjaimen avulla, jolloin rinnan voi olla kytkettynä jopa 16 kompressoria, joiden päällä oloa optimoidaan säätöteknisesti niin, että koko laitos on kuin yksi kompressori. Työssä tarkastellaan myös kompressorin em. sovellutuksista yli kahdeksan vuoden ajalta kaupallista kohteista saatuja käyttökokemuksia. Pääsäätöisesti voi sanoa, että jokaisessa uudessa sovellutuksessa ilmenee uusia reunaehtoja ja järjestelmäkohtaisia vaatimuksia, jotka täytyy huomioida kompressorin säädössä ja ominaisparametreissa.

The performance and the characteristic field of a centrifugal compressor

Tässä työssä tarkastellaan radiaalikompressorin puristusprosessiin liittyvä peruslaskenta. Ilmankosteuden vaikutukset laskentaan huomioidaan ja kompressorin tunnuskenttä esitellään tässä työssä. Esimerkkinä lasketaan pisteitä kompressorin tunnuskentästä.

Development of tender information process by business intelligence in a global company unit

The purpose of this Thesis was to study what is the present situation of Business Intelligence of the company unit. This means how efficiently unit uses possibilities of modern information management systems. The aim was to resolve how operative informa-tion management of unit’s tender process could be improved by modern information technology applications. This makes it possible that tender processes could be faster and more efficiency. At the beginning it was essential to acquaint oneself with written literature of Business Intelligence. Based on Business Intelligence theory is was relatively easy but challenging to search and discern how tender business could be improved by methods of Busi-ness Intelligence. The empirical phase of this study was executed as qualitative research method. This phase includes theme and natural interviews on the company. Problems and challenges of tender process were clarified in a part an empirical phase. Group of challenges were founded when studying information management of company unit. Based on theory and interviews, group of improvements were listed which company could possible do in the future when developing its operative processes.

Developing an Improved System for Allocating Support Unit Costs to Business Units

The objective of this study is to develop an improved support unit cost allocation system for a medium-sized technology company, and to examine which options for overhead cost accounting exist. The study begins with presenting the terminology and methods associated with overhead cost accounting and responsibility accounting. Also the most common challenges and resulting benefits of overhead cost allocation system development are brought up. As one research method two case studies were conducted for benchmarking purposes. These external cases are compared with the principal company’s cost allocation system and reflected against the theoretical background. In the empirical section interviews were used as the primary source of information alongside self studying principal company’s old cost allocation method. Interviews revealed the main weaknesses of the old system and proposals for a new one, which were utilized in setting targets for developing the new system. As a result of the development process an improved support unit cost allocation system was realized for year 2009. The new system is able to handle support unit costs in more detail enhancing the transparency and fairness of resulting cost allocations. Parts of support unit costs are now seen as business units’ own costs rather than group-level overhead. Also recommendations for further development are made after analyzing how well the targets were reached.

Performance Improvement of Centrifugal Compressor Stage with Pinched Geometry or Vaned Diffuser

Centrifugal compressors are widely used for example in refrigeration processes, the oil and gas industry, superchargers, and waste water treatment. In this work, five different vaneless diffusers and six different vaned diffusers are investigated numerically. The vaneless diffusers vary only by their diffuser width, so that four of the geometries have pinch implemented to them. Pinch means a decrease in the diffuser width. Four of the vaned diffusers have the same vane turning angle and a different number of vanes, and two have different vane turning angles. The flow solver used to solve the flow fields is Finflo, which is a Navier-Stokes solver. All the cases are modeled with the Chien's k – έ- turbulence model, and selected cases are modeled also with the k – ώ-SST turbulence model. All five vaneless diffusers and three vaned diffusers are investigated also experimentally. For each construction, the compressor operating map is measured according to relevant standards. In addition to this, the flow fields before and after the diffuser are measured with static and total pressure, flow angle and total temperature measurements. When comparing the computational results to the measured results, it is evident that the k – ώ-SST turbulence model predicts the flow fields better. The simulation results indicate that it is possible to improve the efficiency with the pinch, and according to the numerical results, the two best geometries are the ones with most pinch at the shroud. These geometries have approximately 4 percentage points higher efficiency than the unpinched vaneless diffusers. The hub pinch does not seem to have any major benefits. In general, the pinches make the flow fields before and after the diffuser more uniform. The pinch also seems to improve the impeller efficiency. This is down to two reasons. The major reason is that the pinch decreases the size of slow flow and possible backflow region located near the shroud after the impeller. Secondly, the pinches decrease the flow velocity in the tip clearance, leading to a smaller tip leakage flow and therefore slightly better impeller efficiency. Also some of the vaned diffusers improve the efficiency, the increment being 1...3 percentage points, when compared to the vaneless unpinched geometry. The measurement results confirm that the pinch is beneficial to the performance of the compressor. The flow fields are more uniform with the pinched cases, and the slow flow regions are smaller. The peak efficiency is approximately 2 percentage points and the design point efficiency approximately 4 percentage points higher with the pinched geometries than with the un- pinched geometry. According to the measurements, the two best geometries are the ones with the most pinch at the shroud, the case with the pinch only at the shroud being slightly better of the two. The vaned diffusers also have better efficiency than the vaneless unpinched geometries. However, the pinched cases have even better efficiencies. The vaned diffusers narrow the operating range considerably, whilst the pinch has no significant effect on the operating range.

Structural development of the harvester head saw unit

The main goal of the thesis was to further develop harvester head saw device to the Finnish forest machine manufacturer. The work was done from the basis of the manufacturer´s current production model and the earlier study from this same subject called: “Development of chain saw for harvester” Tero Kaatrasalo, 2004. The work was focused to improving the serviceability and reliability of the saw device, but design also included adding few beforehand determined new features into the saw unit. This was done to give some added value for the end customer. The work includes analysis of the earlier saw devices and ideations of the improvements for the structure.

The intrinsic mechanisms of softwood fiber damage in brown stock fiber line unit operations Lappeenranta 2010

The effects of pulp processing on softwood fiber properties strongly influence the properties of wet and dry paper webs. Pulp strength delivery studies have provided observations that much of the strength potential of long fibered pulp is lost during brown stock fiber line operations where the pulp is merely washed and transferred to the subsequent processing stages. The objective of this work was to study the intrinsic mechanisms which maycause fiber damage in the different unit operations of modern softwood brown stock processing. The work was conducted by studying the effects of industrial machinery on pulp properties with some actions of unit operations simulated in laboratory scale devices under controlled conditions. An optical imaging system was created and used to study the orientation of fibers in the internal flows during pulp fluidization in mixers and the passage of fibers through the screen openings during screening. The qualitative changes in fibers were evaluated with existing and standardized techniques. The results showed that each process stage has its characteristic effects on fiber properties: Pulp washing and mat formation in displacement washers introduced fiber deformations especially if the fibers entering the stage were intact, but it did not decrease the pulp strength properties. However, storage chests and pulp transfer after displacement washers contributed to strength deterioration. Pulp screening proved to be quite gentle, having the potential of slightly evening out fiber deformations from very deformed pulps and vice versa inflicting a marginal increase in the deformation indices if the fibers were previously intact. Pulp mixing in fluidizing industrial mixers did not have detrimental effects on pulp strength and had the potential of slightly evening out the deformations, provided that the intensity of fluidization was high enough to allow fiber orientation with the flow and that the time of mixing was short. The chemical and mechanical actions of oxygen delignification had two distinct effects on pulp properties: chemical treatment clearly reduced pulp strength with and without mechanical treatment, and the mechanical actions of process machinery introduced more conformability to pulp fibers, but did not clearly contribute to a further decrease in pulp strength. The chemical composition of fibers entering the oxygen stage was also found to affect the susceptibility of fibers to damage during oxygen delignification. Fibers with the smallest content of xylan were found to be more prone to irreversibledeformations accompanied with a lower tensile strength of the pulp. Fibers poor in glucomannan exhibited a lower fiber strength while wet after oxygen delignification as compared to the reference pulp. Pulps with the smallest lignin content on the other hand exhibited improved strength properties as compared to the references.

Estimation of existing cable systems in generator-busbar unit and choice the optimal solution for its modernization

The aim of this master’s thesis is to develop an algorithm to calculate the cable network for heat and power station CHGRES. This algorithm includes important aspect which has an influence on the cable network reliability. Moreover, according to developed algorithm, the optimal solution for modernization cable system from economical and technical point of view was obtained. The conditions of existing cable lines show that replacement is necessary. Otherwise, the fault situation would happen. In this case company would loss not only money but also its prestige. As a solution, XLPE single core cables are more profitable than other types of cable considered in this work. Moreover, it is presented the dependence of value of short circuit current on number of 10/110 kV transformers connected in parallel between main grid and considered 10 kV busbar and how it affects on final decision. Furthermore, the losses of company in power (capacity) market due to fault situation are presented. These losses are commensurable with investment to replace existing cable system.

Integration of the Food Waste Disposer Unit to the Existing Sewage System

Among the numerous approaches to food waste treatment, the food waste disposers method (FWDs), as a newcomer, has become slowly accepted by the general public owing to the worries about its impact on the existing sewage system. This paper aims to justify the role of FWDs in the process of urbanization in order to better prepare a city to take good care of the construction of its infrastructure and the solid waste treatment. Both the literatures and the case study help to confirm that FWDs has no negative effects on the wastewater treatment plant and it is also environmental friendly by reducing the greenhouse gas emissions. In the case study, the Lappeenranta waste water treatment plant has been selected in order to figure out the possible changes to a WWTP following the integration of FWDs: the observation shows only minor changes take place in a WWTP, in case of 25% application, like BOD up 7%, TSS up 6% and wastewater flowrate up 6%, an additional sludge production of 200 tons per year and the extra yield of methane up to 10000m3 per year; however, when the utilization rate of FWD is over 75%, BOD, TSS, and wastewater flowrate will experience more significant changes, thus exerting much pressure on the existing WWTP. FWDs can only be used in residential areas or cities equipped with consummate drainage network within the service sphere of WWTP, therefore, the relevant authority or government department should regulate the installation frequency of FWDs, while promoting the accessory application of FWDs. In the meanwhile, WWTP should improve their treatment process in order to expand their capacity for sludge treatment so as to stay in line with the future development of urban waste management.

Insulation System in an Integrated Motor Compressor

A high-speed and high-voltage solid-rotor induction machine provides beneficial features for natural gas compressor technology. The mechanical robustness of the machine enables its use in an integrated motor-compressor. The technology uses a centrifugal compressor, which is mounted on the same shaft with the high-speed electrical machine driving it. No gearbox is needed as the speed is determined by the frequency converter. The cooling is provided by the process gas, which flows through the motor and is capable of transferring the heat away from the motor. The technology has been used in the compressors in the natural gas supply chain in the central Europe. New areas of application include natural gas compressors working at the wellheads of the subsea gas reservoir. A key challenge for the design of such a motor is the resistance of the stator insulation to the raw natural gas from the well. The gas contains water and heavy hydrocarbon compounds and it is far harsher than the sales gas in the natural gas supply network. The objective of this doctoral thesis is to discuss the resistance of the insulation to the raw natural gas and the phenomena degrading the insulation. The presence of partial discharges is analyzed in this doctoral dissertation. The breakdown voltage of the gas is measured as a function of pressure and gap distance. The partial discharge activity is measured on small samples representing the windings of the machine. The electrical field behavior is also modeled by finite element methods. Based on the measurements it has been concluded that the discharges are expected to disappear at gas pressures above 4 – 5 bar. The disappearance of discharges is caused by the breakdown strength of the gas, which increases as the pressure increases. Based on the finite element analysis, the physical length of a discharge seen in the PD measurements at atmospheric pressure was approximated to be 40 – 120 m. The chemical aging of the insulation when exposed to raw natural gas is discussed based on a vast set of experimental tests with the gas mixture representing the real gas mixture at the wellhead. The mixture was created by mixing dry hydrocarbon gas, heavy hydrocarbon compounds, monoethylene glycol, and water. The mixture was chosen to be more aggressive by increasing the amount of liquid substances. Furthermore, the temperature and pressure were increased, which resulted in accelerated test conditions. The time required to detect severe degradation was thus decreased. The test program included a comparison of materials, an analysis of the e ects of di erent compounds in the gas mixture, namely water and heavy hydrocarbons, on the aging, an analysis of the e ects of temperature and exposure duration, and also an analysis on the e ect of sudden pressure changes on the degradation of the insulating materials. It was found in the tests that an insulation consisting of mica, glass, and epoxy resin can tolerate the raw natural gas, but it experiences some degradation. The key material in the composite insulation is the resin, which largely defines the performance of the insulation system. The degradation of the insulation is mostly determined by the amount of gas mixture di used into it. The di usion was seen to follow Fick’s second law, but the coe cients were not accurately defined. The di usion was not sensitive to temperature, but it was dependent upon the thermodynamic state of the gas mixture, in other words, the amounts of liquid components in the gas. The weight increase observed was mostly related to heavy hydrocarbon compounds, which act as plasticizers in the epoxy resin. The di usion of these compounds is determined by the crosslink density of the resin. Water causes slight changes in the chemical structure, but these changes do not significantly contribute to the aging phenomena. Sudden changes in pressure can lead to severe damages in the insulation, because the motion of the di used gas is able to create internal cracks in the insulation. Therefore, the di usion only reduces the mechanical strength of the insulation, but the ultimate breakdown can potentially be caused by a sudden drop in the pressure of the process gas.