Effect of Mesa Size on Thermal Characteristics of Vertical-cavity Surface-emitting Lasers

The effect of mesa size on the thermal characteristics of etched mesa vertical-cavity surfaceemitting lasers(VCSELs) is studied. The numerical results show that the mesa size of the top mirror strongly influences the temperature distribution inside the etched mesa VCSEL. Under a certain driving voltage, with decreasing mesa size, the location of the maximal temperature moves towards the p-contact metal, the temperature in the core region of the active layer rises greatly, and the thermal characteristics of the etched mesa VCSELs will deteriorate.

Array for 980nm Vertical Cavity Surface Emitting Diodes and Detectors

Both the vertical cavity surface emitting diodes and detectors are fabricated by using the epitaxial wafer with resonant cavity structure. Their characteristics are analyzed. The light emitters have high spectral purity of 4.8nm and high electroluminescence intensity of 0.7mW while injection current is 50mA. A 1*16 array of surface emitting light device is tested on line by probes and then used for module. The light detectors have wavelength selectivity and space selectivity. The required difference in input mirror reflectivity between emitters and detectors can easily be achieved though varying the numbers of top DBR period by etching.

Small Signal Equivalent Circuit Model and Modulation Properties of Vertical Cavity-Surface Emitting Lasers

Small signal equivalent circuit model and modulation properties of vertical cavity-surface emitting lasers (VCSEL's) are presented. The modulation properties both in analytic-equation calculation and in circuit model simulation are studied. The analytic-equation calculation of the modulation properties is calculated by using Mathcad program and the circuit model simulation is simulation is simulated by using Pspice program respectively. The results of calculation and the simulation are in good agreement with each other. Experiment is performed to testify the circuit model.

A Single Mode 980nm InGaAs/GaAs/AlGaAs Large Optical Cavity Quantum Well Laser with Low Vertical Divergence Angle

To achieve high optical power as well as low vertical divergence angle, a new kind of optimized large optical cavity (LOC) structure is applied to a ridge waveguide 980nm InGaAs/GaAs/AlGaAs multi-quantum well laser. The optical power density in the waveguide is successfully reduced. The maximum output power is more than 400mW with a slope efficiency of 0.89W/A and the far-field vertical divergence angle is lowered to 23°.

Ultralow Threshold Red Vertical-Cavity Surface-Emitting Lasers

国家自然科学基金

Polarization switching current of vertical cavity surface-emitting Lasers in an applied electric field

The polarization of vertical-cavity surface-emitting laser (VCSEL) can be controlled by electro-optic birefringence. We calculated the birefringence resulted from external electric field which was imposed on the top DBR of VCSEL by assuming that the two polarization modes were in the same place of the gain spectra in the absence of electric field beginning. By modifying SFM, the affection of the electric field strength on the polarization switching currents between the two polarization modes had been shown.

Small signal equivalent circuit model of vertical cavity surface emitting lasers

Small signal equivalent circuit model of vertical cavity surface emitting lasers (VCSEL's) is given in this paper. The modulation properties of VCSEL are simulated using this model in Pspice program. The simulation results are good agree with experiment data. Experiment is performed to testify the circuit model.

1.5 mu m DFB integrated with vertical tapered spotsize converter fabricated by selective MOVPE

1.5 mu m DFB LD butt-joint integrated with vertical tapered spotsize converter was fabricated by LP-MOVPE. The vertical far field angle (FWHM) was decreased from 34degrees to 10degrees the threshold currents was as low as 19.8mA, the output power was 9.6mw at 100mA without HR coating and the SMSR was 35.8dB. The 1-dBm misalignment tolerance was 3.2 mu m, while the counterpart of the device without SSC was 2.2 mu m.

High efficiency, low vertical divergence angle 980nnn Al-free active region lasers with novel large optical cavity and asymmetrical cladding layers

980nm InGaAs/InGaAsP/AlGaAs strained quantum well lasers,vitta novel large optical cavity and asymmetrical claddings was fabricated bg MOCVD. Very high differential quantum efficiency elf 90% (1.15W/A) and low vertical divergence angle of 24 degrees at long cavity length were obtained for 100 mu m stripe lasers. The differential quantum efficiency is up to 94% (1.20) at cavity length of 500 mu m.

Visible vertical cavity surface emitting laser

We have designed and fabricated the visible vertical-cavity surface-emitting lasers (VCSEL's) by using metalorganic vapor phase epitaxy (MOVPE). We use the 8 lambda optical cavities with 3 quantum wells in AlGaInP/AlGaAs red VCSEL's to reduce the drift leakage current and enhance the model gain in AlGaInP active region. The structure has a p-type stack with 36 DBR pairs on the top and an n-type with 55-1/2 pairs on the bottom. Using micro-area reflectance spectrum, we try to get a better concordance between the center wavelength of DBR and the emitting wavelength of the active region. We used a component graded layer of 0.05 lambda thick (x = 0.5 similar to 0.9) at the p-type DBR AlGaAs/AlAs interface to reduce the resistance of p-type DBR. We use selective oxidation to define the current injection path. Because the oxidation rate of a thick layer is faster than a thinner one, we grown a thick AlAs layer close to the active region. In this way, we got a smaller active region for efficient confinement of injected carriers (the aperture area is 3 x 3 mu m) to reduce the threshold and, at the same time, a bigger conductive area in the DBR layers to reduce the resistance. We employ Zn doping on the p-side of the junction to improve hole injection and control the Zn dopant diffusion to get proper p-i-n junction. At room temperature, pulse operation of the laser has been achieved with the low threshold current of 0.8mA; the wavelength is about 670nm.

The enhancement of spontaneous emission factor in selectively oxidized vertical cavity lasers with double oxide layers

The behaviors of lateral propagating modes in the aperture and the oxidized regions are investigated numerically for selectively oxidized vertical-cavity surface-emitting lasers (VCSELs). The results show that the lateral propagating modes in the oxidized region are greatly affected by the oxide layer due to its low index, the modes are divergence for the VCSELs with sufficient thick double oxide layers. So the coupling between the modes in the aperture and oxidized regions is very weak, and we can expect that the lateral spontaneous emission is greatly affected in this case. Ignoring the contribution of the lateral spontaneous emission, we calculate spontaneous emission factor by counting the total number of the guided modes in selectively oxidized VCSELs with double oxide layers. The results agree very well with the reported measurements and are inversely proportional to the lateral index step.

Transport properties through quantum dot in a vertical electric field

The transport properties through a quantum dot are calculated using the recursion method. The results show that the electric fields can move the conductive peaks along the high- and low-energies. The electric field changes the intensity of conductance slightly. Our theoretical results should be useful for researching and making low-dimensional semiconductor optoelectronic devices. (C) 2002 Elsevier Science B.V. All rights reserved.

Stability improvement of selective oxidation during the fabrication of InGaAs/GaAs vertical cavity surface emitting laser

The effects of the carrier gas flow and water temperature on the oxidation rate for different reaction temperatures were investigated. The optimum conditions for stable oxidation were obtained. Two mechanisms of the oxidation process are revealed. One is the flow-controlling process, which is unstable. The other is the temperature-controlling process, which is stable. The stable region decreases for higher reaction temperatures. The simulation results for the stable oxidation region are also given. With optimum oxidation conditions, the stability and precision of the oxidation can be dramatically improved.

Microphotoluminescence investigation of InAs quantum dot active region in 1.3 mu m vertical cavity surface emitting laser structure

Microphotoluminescence (mu-PL) investigation has been performed at room temperature on InAs quantum dot (QD) vertical cavity surface emitting laser (VCSEL) structure in order to characterize the QD epitaxial structure which was designed for 1.3 mu m wave band emission. Actual and precise QD emission spectra including distinct ground state (GS) and excited state (ES) transition peaks are obtained by an edge-excitation and edge-emission (EEEE) mu-PL configuration. Conventional photoluminescence methods for QD-VCSELs structure analysis are compared and discussed, which indicate the EEEE mu-PL is a useful tool to determine the optical features of the QD active region in an as-grown VCSEL structure. Some experimental results have been compared with simulation results obtained with the aid of the plane-wave admittance method. After adjustment of epitaxial growth according to EEEE mu-PL measurement results, QD-VCSEL structure wafer with QD GS transition wavelength of 1300 nm and lasing wavelength of 1301 nm was obtained.