Theoretical analysis of modal gain in p-doped 1.3 mu m InAs/GaAs quantum dot lasers

A theoretical study of modal gain in p-doped 1.3 mu m InAs/GaAs quantum dot (QD) lasers is presented. The expression of modal gain is derived, which includes an effective ratio that describes how many QDs contribute to the modal gain. The calculated results indicate that the modal gain with the effective ratio is much smaller than that without the effective ratio. The calculated maximum modal gain is is a good agreement with the experimental data. Furthermore, QDs with lower height or smaller aspect ratio are beneficial in achieving a larger maximum modal gain that leads to lower threshold current density and higher differential modal gain. (C) 2009 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Effect of noncoherent islands on the optical properties of the 1.3 mu m InAs/GaAs quantum dots during rapid thermal annealing

The effect of thermal annealing of InAs/GaAs quantum dots (QDs) with emission wavelength at 1.3 mu m have been investigated by photoluminescence (PL) and transmission electron microscopy (TEM measurements. There is a dramatic change in the A spectra when the annealing temperature is raised up to 800 degrees C: an accelerated blushifit of the main emission peak of QDs together with an inhomogeneous broadening of the linewidth. The TEM images shows that the lateral size of normal QDs decreases as the annealing temperature is increased, while the noncoherent islands increase their size and densit. A small fraction of the relative large QDs contain dislocations when the annealing temperature increases up to 800 degrees C. The latter leads to the strong decrease of the PL intensity.

1.3 mu m high indium content (42.5%) GaInNAs/GaAs quantum wells grown by molecular beam epitaxy

High structural and optical quality 1.3 mu m GaInNAs/GaAs quantum well (QW) samples with 42.5% indium content were successfully grown by molecular beam epitaxy. The growth of well layers was monitored by reflection high-energy electron diffraction (RHEED). Room temperature photoluminescence (PL) peak intensity of the GaIn0.425NAs/GaAs (6 nm / 20 nm) 3QW is higher than, and the full width at half maximum (FWHM) is comparable to, that of In0.425GaAs/GaAs 3QW, indicating improved optical quality due to strain compensation effects by introducing N to the high indium content InGaAs epilayer. The measured (004) X-ray rocking curve shows clear satellite peaks and Pendellosung fringes, suggesting high film uniformity and smooth interfaces. The cross sectional TEM measurements further reveal that there are no structural defects in such high indium content QWs. (c) 2006 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Large-Signal Performance of 1.3 mu m InAs/GaAs quantum-dot lasers

Submitted by 阎军 (yanj@red.semi.ac.cn) on 2010-06-04T08:15:32Z No. of bitstreams: 1 Large-Signal Performance of 1.3 mu m InAs-GaAs quantum-dot lasers.pdf: 281494 bytes, checksum: 1ebcdfdc887e3a3b279e07b3f655167b (MD5)

高性能1.3 μm InAs/GaAs量子点激光器的研究

Submitted by 阎军 (yanj@red.semi.ac.cn) on 2010-07-12T02:19:08Z No. of bitstreams: 1 博士论文-季海铭.pdf: 11683811 bytes, checksum: 011e82d00d16fcfb62342bd93cacf388 (MD5)

Temperature-dependent modulation characteristics for 1.3 mu m InAs/GaAs quantum dot lasers

Temperature-dependent modulation characteristics of 1.3 mu m InAs/GaAs quantum dot (QD) lasers under small signals have been carefully studied at various bias currents. Based on experimental observations, it is found that the modulation bandwidth significantly increases when excited state (ES) lasing emerges at high temperature. This is attributed to additional photons emitted by ES lasing which contribute to the modulation response. A rate equation model including two discrete electron energy levels and the level of wetting layer has been used to investigate the temperature-dependent dynamic behavior of the QD lasers. Numerical investigations confirm that the significant jump for the small signal modulation response is indeed caused by ES photons. Furthermore, we identify how the electron occupation probabilities of the two discrete energy levels can influence the photon density of different states and finally the modulation rate. Both experiments and numerical analysis show that the modulation bandwidth of QD lasers at high temperature can be increased by injecting more carriers into the ES that has larger electron state degeneracy and faster carrier's relaxation time than the ground state.

High Characteristic Temperature 1.3 mu m InAs/GaAs Quantum-Dot Lasers Grown by Molecular Beam Epitaxy

We report the molecular beam epitaxy growth of 1.3 mu m InAs/GaAs quantum-dot (QD) lasers with high characteristic temperature T-0. The active region of the lasers consists of five-layer InAs QDs with p-type modulation doping. Devices with a stripe width of 4 mu m and a cavity length of 1200 mu m are fabricated and tested in the pulsed regime under different temperatures. It is found that T-0 of the QD lasers is as high as 532K in the temperature range from 10 degrees C to 60 degrees C. In addition, the aging test for the lasers under continuous wave operation at 100 degrees C for 72 h shows almost no degradation, indicating the high crystal quality of the devices.

A 10 Gb/s Directly-Modulated 1.3 mu m InAs/GaAs Quantum-Dot Laser

We demonstrate 10 Gb/s directly-modulated 1.3 mu m InAs quantum-dot (QD) lasers grown on GaAs substrates by molecular beam epitaxy. The active region of the QD lasers consists of five-stacked InAs QD layers. Ridge-waveguide lasers with a ridge width of 4 mu m and a cavity length of 600 mu m are fabricated with standard lithography and wet etching techniques. It is found that the lasers emit at 1293 nm with a very low threshold current of 5 mA at room temperature. Furthermore, clear eye-opening patterns under 10 Gb/s modulation rate at temperatures of up to 50 degrees C are achieved by the QD lasers. The results presented here have important implications for realizing low-cost, low-power-consumption, and high-speed light sources for next-generation communication systems.

Self-heating effect in 1.3 mu m p-doped InAs/GaAs quantum dot vertical cavity surface emitting lasers

The self-heating effect in 1.3 mu m p-doped InAs/GaAs quantum dot (QD) vertical cavity surface emitting lasers (VCSELs) has been investigated using a self-consistent theoretical model. Good agreement is obtained between theoretical analysis and experimental results under pulsed operation. The results show that in p-doped QD VCSELs, the output power is significantly influenced by self-heating. About 60% of output power is limited by self-heating in a device with oxide aperture of 5x6 mu m(2). This value reduces to 55% and 48%, respectively, as the oxide aperture increases to 7x8 and 15x15 mu m(2). The temperature increase in the active region and injection efficiency of the QDs are calculated and discussed based on the different oxide aperture areas and duty cycle.

Self-Heating Effect on the Two-State Lasing Behaviors in 1.3-mu m InAs-GaAs Quantum-Dot Lasers

Experimental and theoretical study of the self-heating effect on the two-state lasing behaviors in 1.3-mu m self-assembled InAs-GaAs quantum dot (QD) lasers is presented. Lasing spectra under different injected currents, light-current (L-I) curves measured in continuous and pulsed regimes as well as a rate-equation model considering the current heating have been employed to analyze the ground-state (GS) and excited-state (ES) lasing processes. We show that the self-heating causes the quenching of the GS lasing and the ES lasing by the increased carrier escape rate and the reduced maximum modal gain of GS and ES.

铬系催化剂聚合1,3-双烯烃的研究

铬系催化剂是合成1,2-聚丁二烯和3,4-聚异戊二烯的一种主要催化剂体系，1,2-聚丁二烯和3,4-聚异戊二烯是制造高性能轮胎的重要原料。本论文研究了以含氮化合物和含磷化合物为配体的铬催化剂合成1,2-聚丁二烯和3,4-聚异戊二烯的反应规律。 1. 以邻菲咯啉为配体的铬催化剂在己烷中50℃下可获得1,2-结构、顺-1,4-结构和反-1,4-结构单元含量分别约为50%、30%和20%，分子量呈双峰分布的聚丁二烯。改变聚合温度，可有效控制聚合物的1,2-结构含量和分子量及分布。催化剂通过预陈化方式，可有效抑制低聚物的生成。 2. 以亚磷酸二烷基酯为配体的铬催化剂是合成1,2-聚丁二烯的高效催化剂，所得聚合物具有高的1,2-结构含量（> 78%）。改变烷基铝和亚磷酸二烷基酯的结构，可以得到高熔点或低熔点间同1,2-聚丁二烯和无规1,2-聚丁二烯。催化剂以现配方式的活性最高。 3. 以磷酸三苯酯为配体的铬催化剂可获得间同1,2-聚丁二烯，而聚合物中含有低聚物。催化剂以现配方式的活性最高。聚合物的熔点，低聚物的含量与磷酸三苯酯的结构有一定的关系。 4. 以邻菲咯啉为配体的铬催化剂在50℃下聚合异戊二烯，具有高的催化活性，可获得3,4-结构含量约67%的高分子量无规3,4-聚异戊二烯。催化剂的组成对聚合物的微观结构无明显影响。改变聚合温度，可有效控制聚合物的3,4-结构含量和分子量及分布。

铁系催化剂聚合1，3-双烯烃的研究

1，2-聚丁二烯和3，4-聚异戊二烯是制造高性能轮胎的原料。本论文研究了以含磷化合物为第三组份的铁催化剂合成1，2-聚丁二烯和3，4-聚异戊二烯的反应规律：1．以二乙基亚磷酸酷为第三组份的铁催化剂可在己烷中，较高温度（50℃）下聚合1，3-丁二烯。通过控制催化剂组份的配比，可制备间同和无规1，2-聚丁二烯。所得间同1，2-聚丁二烯的1，2-结构含量为91％，间规度为90％；所得无规1，2-聚丁二烯的硫化胶具有优异的抗干、湿滑性能。2．以三苯基磷酸酷为第三组份的铁催化剂是合成高间同1，2一聚丁二烯的高效催化剂。所得聚合物具有高的1，2-结构含量（ca.95％），高的间规度（ca.95％）。聚合物的微观结构与催化剂组成等反应因素无关。3．以二烷基亚磷酸醋为第三组份的铁催化剂可在己烷中，较高温度（50℃）下聚合异戊二烯。二烷基亚磷酸醋中烷基影响聚合活性的顺序为乙基一甲基＞正丁基＞异辛基。所得聚异戊二烯的3，4（含1，2）结构含量保持在60％左右，不受反应条件的影响。4．改性甲基铝氧烷（MMAO）活化的铁催化剂聚合异戊二烯，在相当低的MMAO用量下（Al／Fe=20，摩尔比）即有高的催化活性。溶剂影响聚合活性的顺序为甲苯＞环己烷＞己烷＞二氯甲烷。所得聚异戊二烯的3，4（含1，2）结构含量稳定在60％。

p型掺杂1.3 μm InAs/GaAs量子点激光器的最大模式增益特性的研究

对p型掺杂1.3 μm InAs/GaAs量子点激光器的最大模式增益进行了实验和理论分析.实验上,测量了不同腔长激光器阈值电流密度与总损耗的对应关系,拟合出的最大模式增益为17.5 cm~(-1),与相同结构非掺杂量子点激光器的最大模式增益一致.同时理论分析表明,p型掺杂对InAs/GaAs量子点激光器的最大模式增益并无影响,并且最大模式增益的计算结果与实验值相符.具有较小高度或高宽比的量子点能达到更高的最大模式增益,而较高的最大模式增益对p型掺杂1.3 μm InAs/GaAs自组织量子点激光器在光通信系统中的应用具有重要意义.