大功率半导体激光器阵列的封装技术

半导体激光器阵列的应用已基本覆盖了整个光电子领域，成为当今光电子科学的重要技术。本文介绍了半导体激光器阵列的发展及其应用。着重阐述了半导体激光器阵列的封装技术——热沉材料的选择及其结构优化、热沉与半导体激光器阵列之间的焊接技术、半导体激光器阵列的冷却技术、与光纤的耦合技术等。

大功率半导体激光器二维阵列模块特性分析

根据固体激光器抽运的技术要求，设计了一种具有水冷装置的大功率半导体激光器二维阵列模块，并对半导体激光器热沉和致冷系统的热流进行了分析。在不同占空比下，对该模块进行了测试与分析。该模块的中心波长为810nm，光谱半峰全宽（FWHM）为2．5nm，工作电流为110A（200μs，10％占空比），循环水温为15℃时输出峰值功率为280W。结果表明，该封装结构在占空比小于5％时器件工作特性良好，在10％占空比F也可正常工作。利用该模块可以组合成多种几何结构、功率更高的半导体激光器组件。

体布拉格光栅外腔半导体激光器光谱特性研究

用体布拉格光栅(VBG)作为反馈元件与瓦级半导体激光器(LD)以及快轴准直柱透镜构成一个可以将半导体激光器的工作波长稳定在体布拉格光栅布拉格波长处的外腔激光器。测量了体布拉格光栅外腔激光器的波长稳定性与其工作电流、热汇温度、激光束准直装置等因素的关系。分析了波长稳定效果与半导体激光器增益谱特性、外腔结构参量等因素的关系。研究表明,在相同的工作电流、热汇温度下,当准直柱透镜直径为0.4 mm时的波长稳定效果较好;在此情况下,当热汇温度控制在30 ℃,工作电流从0.5 A增加到1.5 A的测量范围内,以及当工

高功率半导体激光器线阵列的波长锁定技术

高功率半导体激光器光谱随温度和工作电流的变化比较大，光谱线宽比较宽，这些缺点直接限制了其实际应用。因此，高功率半导体激光器波长稳定技术的研究是激光领域的一个重要研究方向。对波长稳定技术进行研究。实验用体布拉格光栅（VBG）作为反馈元件与高功率半导体激光器线阵列，构成可以对其波长进行锁定的外腔激光器。分析了外腔激光器的波长锁定效果与高功率半导体激光器工作电流、冷却温度、工作电流的占空比和“smile”现象等因素的关系。研究结果表明，高功率半导体激光器的工作电流、冷却温度、工作电流的占空比会影响其激射波长，当激射波长与VBG的布拉格波长差值小于3．0nm时，可以得到较好的波长锁定效果，而阵列本身的“smile”现象对其波长锁定的影响不大。

连续工作的体布拉格光栅外腔半导体激光器的温度特性

对体布拉格光栅(VBG)作为波长选择元件的外腔半导体激光器的波长锁定进行了实验研究,报道了连续运转输出功率达43.5 W的半导体激光器阵列的体布拉格光栅波长锁定实验结果,给出了不同热沉温度下的稳定的波长锁定结果,说明采用体布拉格光栅外腔将减小半导体激光器的温控压力。实验中发现,随着注入电流的增大,输出激光功率逐渐增强,锁定的激射波长向长波长方向偏移。在输出功率为34.5 W时,波长红移约0.56 nm。这一移动与实验测量的体布拉格光栅的温度特性相吻合。连续和高占空比运行、高输出功率情况下,在器件的设计和使用时应该考虑这一效应。

适合于小飞机防撞系统的机载小型激光测距仪

报道了一种重量轻、功耗低、适合于小飞机防撞系统应用的小型激光测距仪。系统基于脉冲激光测距原理，采用905nm半导体脉冲激光器、电感升压式偏置高压电源和可编程逻辑器件（PLD），研制出重量不大于100g，功耗不大于625mW，测量范围100m，盲区3．0m，分辨率±1m的机载小型激光测距仪。实验测试结果表明，其各项技术性能指标符合无人驾驶小飞机防撞系统的应用要求。

连续波工作大功率半导体激光器阵列的温度分布

用Ansys软件模拟了大功率半导体激光器阵列的稳态温度分布，并对自行研制的半导体激光器阵列的温度变化进行了测试，结果表明理论计算与实验结果基本吻合。该模拟结果对大功率半导体激光器阵列的封装设计具有现实的指导意义。

Designing a coupler for the intersatellite optical communication system

Coupling a single-mode laser diode with 200 mW to a single-mode fiber (SMF) through an orthonormal aspherical cylindrical lens and a GRIN lens for the intersatellite optical communication system is proposed and demonstrated. We experimentally studied how the coupling efficiency changes with the SMF's position displacement and axial angle variation, and obtained 80 mW output power at the end of the SMF, which shows that the coupling units have satisfied the designed request. (c) 2007 Elsevier GmbH. All rights reserved.

Strong visible up-conversion emissions and thermometric applications of Er3+-Yb3+ codoped Al2O3 prepared by the sol-gel method

The Er3+-Yb3+ codoped Al2O3 has been prepared by the sol-gel method using the aluminium isopropoxide [Al(OC3H7)(3)]-derived Al2O3 sols with addition of the erbium nitrate [Er(NO3)(3) center dot 5H(2)O] and ytterbium nitrate [Yb(NO3)(3) center dot 5H(2)O]. The phase structure, including only two crystalline types of doped Al2O3 phases, theta and gamma, was obtained for the 1 mol% Er3+ and 5 mol% Yb3+ codoped Al2O3 at the sintering temperature of 1,273 K. By a 978 nm semiconductor laser diodes excitation, the visible up-conversion emissions centered at about 523, 545, and 660 nm were obtained. The temperature dependence of the green up-conversion emissions was studied over a wide temperature range of 300-825 K, and the reasonable agreement between the calculated temperature by the fluorescence intensity ratio (FIR) theory and the measured temperature proved that Er3+-Yb3+ codoped Al2O3 plays an important role in the application of high temperature sensor.

Mechanism of polarization pinning in vertical cavity surface emitting lasers using focused ion beam etching

Photoluminescence experiments have identified strain as the origin for polarization pinning in vertical cavity surface emitting lasers post-processed by focused ion beam etching. Theoretical models were applied to deduce the strain in devices. Post-annealing was used to optimize polarization pinning.

Spatial emission control of vertical cavity surface emitting lasers to provide bandwidth gain in multimode fibre links using a simple alignment technique

Etched VCSEL sources are reported which avoid bandwidth collapse in multimode fibre using a simple coupling technique to control the launch. These devices have allowed better than over-filled launch bandwidth for alignment tolerances of ±7 microns.

Ultrashort superradiant pulse generation from a GaN/InGaN heterostructure.

Dicke superradiance from a two-section violet GaN/InGaN semiconductor laser diode is demonstrated for the first time. In the superradiance regime, optical pulses with peak powers in excess of 2.8 W and durations as short as 1.4 ps are generated at repetition rates of up to 10 MHz at the emission wavelength of 408 nm. The properties of superradiant pulse generation from these GaN/InGaN laser diodes are very similar to those reported for infrared AlGaAs/GaAs laser diodes.

Dicke superradiance in GaN quantum wells

We numerically modeled the spatio-temporal dynamics of Dicke superradiance in GaN/InGaN heterostructure quantum wells in a ridge waveguide cavity. Model predictions envisage ultrashort pulses of intensities superior to what can be obtained in mode-locked lasers. ©2010 IEEE.

Superradiance: exploiting quantum phase transition in the real world

Superradiance (SR), or cooperative spontaneous emission, has been predicted by R. Dicke before the invention of the laser. During the last few years one can see a renaissance of both experimental and theoretical studies of the superradiant phase transition in a variety of media, ranging from quantum dots and Bose condensates through to black holes. Until recently, despite of many years of research, SR has been considered as a phenomenon of pure scientific interest without obvious potential applications. However, recent investigations of the femtosecond SR emission generation from semiconductors have opened up some practical opportunities for the exploitation of this quantum optics phenomenon. Here we present a brief review of some features, advantages and potential applications of the SR generation from semiconductor laser structures

Lineshape Analysis of the Beat Signal Between Optical Carrier and Delayed Sidebands

This paper presents the lineshape analysis of the beat signal between the optical carrier and the shifted and delayed side-bands produced by sinusoidal amplitude modulation. It is shown that the beat signal has a typical lineshape with a very narrow delta-peak superposed on a quasi-Lorentzian profile. Theoretical explanation for the appearance of this peak has been given based on optical spectral structure constructed by a large number of optical wave trains. It is predicted that the delta-peak is originated from the beat between the wave trains in the carrier and those in the delayed sidebands when their average coherence length is longer than the delay line. Experiments carried out using different delay lines clearly show that the delta-peak is always located at the modulation frequency and decreases with the increasing delay line. Our analysis explicitly indicates that the linewidth is related to the observation time. It is also suggested that the disappearance of the delta-peak can be used as the criterion of coherence elimination.