Heteroepitaxial Growth and Heterojunction Characteristics of Voids-Free n-3C-SiC on p-Si(100)

Highly oriented voids-free 3C-SiC heteroepitaxial layers are grown on φ50mm Si (100) substrates by low pressure chemical vapor deposition (LPCVD). The initial stage of carbonization and the surface morphology of carbonization layers of Si(100) are studied using reflection high energy electron diffraction (RHEED) and scanning electron microscopy (SEM). It is shown that the optimized carbonization temperature for the growth of voids-free 3S-SiC on Si (100) substrates is 1100 ℃. The electrical properties of SiC layers are characterized using Van der Pauw method. The I-V, C-V, and the temperature dependence of I-V characteristics in n-3C-SiC-p-Si heterojunctions with AuGeNi and Al electrical pads are investigated. It is shown that the maximum reverse breakdown voltage of the n-3C-SiC-p-Si heterojunction diodes reaches to 220V at room temperature. These results indicate that the SiC/Si heterojunction diode can be used to fabricate the wide bandgap emitter SiC/Si heterojunction bipolar transistors (HBT's).

A Single Mode 980nm InGaAs/GaAs/AlGaAs Large Optical Cavity Quantum Well Laser with Low Vertical Divergence Angle

To achieve high optical power as well as low vertical divergence angle, a new kind of optimized large optical cavity (LOC) structure is applied to a ridge waveguide 980nm InGaAs/GaAs/AlGaAs multi-quantum well laser. The optical power density in the waveguide is successfully reduced. The maximum output power is more than 400mW with a slope efficiency of 0.89W/A and the far-field vertical divergence angle is lowered to 23°.

Optical analysis of AlGaInP laser diodes with real refractive index guided self-aligned structure

Optical modes of AlGaInP laser diodes with real refractive index guided self-aligned (RISA) structure were analyzed theoretically on the basis of two-dimension semivectorial finite-difference methods (SV-FDMs) and the computed simulation results were presented. The eigenvalue and eigenfunction of this two-dimension waveguide were obtained and the dependence of the confinement factor and beam divergence angles in the direction of parallel and perpendicular to the pn junction on the structure parameters such as the number of quantum wells, the Al composition of the cladding layers, the ridge width, the waveguide thickness and the residual thickness of the upper P-cladding layer were investigated. The results can provide optimized structure parameters and help us design and fabricate high performance AlGaInP laser diodes with a low beam aspect ratio required for optical storage applications.

Low power design in 100 MHz embedded SRAM

Low power design method is used in a 100MHz embedded SRAM. The embedded SRAM used in a FFT chip is divided into 16 blocks. Two-level decoders are used and only one block can be selected at one time by tristate control circuits, while other blocks are set stand-by. The SRAM cell has been optimized and the cell area has been minimized at the same time.

MOCVD growth of cubic GaN: Materials and devices

Many impressive progresses have been made recently on the growth of cubic-phase GaN by MBE and MOCVD. In this paper, some of our recent progress will be reviewed, including the growth of high quality cubic InGaN films, InGaN/GaN heterostructure blue and green LEDs. Cubic-phase GaN films were grown on GaAs (100) substrates by MOCVD. Growth conditions were optimized to obtain pure cubic phase GaN films up to a thickness of 4 mum. An anomalous compressive strain was found in the as-grown GaN films in spite of a smaller lattice constant for GaN compared with that of GaAs substrates. The photoluminescence FWHM of high quality InGaN epilayers was less than 100 meV The InGaN/GaN heterostructure blue LED has intense electroluminescence with a FWHM of 20 nm.

Bandpass filter by a stretch and double-exposure technique

We fabricated a bandpass filter based on Moire Bragg grating in fiber with a uniform phase mask We employed a stretch and two-exposure technique, in which the fiber was exposed to UV light from a KrF excimer through a phase mask and then the fiber is stretched and given another exposure at the same region. Due to the stretch, the periods of these two grating are slightly different, and there is a transmission between two reflection peaks at the Bragg wavelength of these two gratings.Applying different stretch can control the bandpass width of the filter. We measured the stretch characterization of a uniform Bragg grating and found the Bragg wavelength of the grating shifts linearly with the stretched length.We theoretically analyzed the grating structure and its reflection spectrum. The filter's characteristics can be optimized by choosing appropriate parameters. We will give a theoretical discussion concerning which parameters and how they affect the filter's operation.

Growth and fabrication of high performance 980nm strained InGaAs quantum well lasers using novel hybrid material system of InGaAsP and AlGaAs

In this paper, we report on the design, growth and fabrication of 980nm strained InGaAs quantum well lasers employing novel material system of Al-free active region and AlGaAs cladding layers. The use of AlGaAs cladding instead of InGaP provides potential advantages in laser structure design, improvement of surface morphology and laser performance. We demonstrate an optimized broad-waveguide structure for obtaining high power 980nm quantum well lasers with low vertical beam divergence. The laser structure was grown by low-pressure metalorganic chemical vapor deposition, which exhibit a high internal quantum efficiency of similar to 90% and a low internal loss of 1.5-2.5 cm(-1). The broad-area and ridge-waveguide laser devices are both fabricated. For 100 mu m wide stripe lasers with cavity length of 800 mu m, a low threshold current of 170mA, a high slope efficiency of 1.0W/A and high output power of more than 3.5W are achieved. The temperature dependences of the threshold current and the emitting spectra demonstrate a very high characteristic temperature coefficient (T-o) of 200-250K and a wavelength shift coefficient of 0.34nm/degrees C. For 4 mu m-width ridge waveguide structure laser devices, a maximum output power of 340mW with GOD-free thermal roll-over characteristics is obtained.

Using photoluminescence as optimization criterion to achieve high-quality InGaAs/AlGaAs pHEMT structure

The single delta -doped InGaAs/AlGaAs pseudomorphic HEMT structure materials were grown by molecular beam epitaxy. The photoluminescence spectra of the materials were studied. There are two peaks in the photoluminescence spectra of the materials, corresponding to two sub energy levels of InGaAs quantum well. The ratio of the two peak's intensity was used as criterion to optimize the layer structures of the materials. The material with optimized layer ;tructures exhibits the 77 It mobility and two-dimensional electron gas density of 16 500 cm(2)/Vs and 2.58 x 10(12) cm(-2) respectively, and the 300 K mobility and two-dimensional electron gas density of 6800 cm(2)/Vs and 2.55 x 10(12) cm(-2) respectively. The pseudomorphic HEMT devices with gate length of 0.2 mum were fabricated using this material. The maximum transconductance of 650 mS/mm and the cut-off frequency of 81 GHz were achieved. (C) 2001 Elsevier Science B.V. All rights reserved.

Intersubband absorption energy shifts in 3-level system for asymmetric quantum well terahertz emitters

Intersubband absorption energy shifts in 3-level system stemming from depolarization and excitonlike effects are investigated. Analytically, the expressions we derive present good explanations to the conventional 2-level results and bare potential transition energy results; and numerical results show that they are more exact than the previous studies to describe the 3-level system depolarization and excitonlike shift (DES) character especially for higher carrier density (more than 8 x 10(11) cm(-2)). One interesting detail we find is that the "large blue" DES becomes "slight redshift" in the low doping limit (less than 1.9 x 10(11) cm(-2)), which may be neglected by the previous studies of intersubband transitions. Temperature character of DES in the step well structure is also numerically studied. Finally the above are applied to calculate asymmetric step quantum well structures. The two main functional aspects of terahertz (THz) emitters are discussed and several basic optimizing conditions are considered. By adjusting the well geometry parameters and material composition systematically, some optimized structures which satisfy all of the six conditions are recommended in tables. These optimizations may provide useful references to the design of 3-level-based optically pumping THz emitters.

中国医疗废物优化处置技术和管理模式研究

本论文在综合分析国内外医疗废物处置技术及其应用管理模式的基础上，结合中国医疗废物管理和处置现状，提出了中国医疗废物处置技术选择及应用模式，并对如何优化现行医疗废物处置技术和管理模式问题进行了系统的研究。主要研究成果包括： 1．中国医疗废物处置技术选择和应用模式研究。该项研究是在系统研究国际组织和国际公约、国内外医疗废物处置技术应用状况和管理模式基础上，结合中国医疗废物的产生、处置技术应用以及环境管理模式的特点和存在的问题，针对焚烧和非焚烧两大技术流派开展的。 2．中国医疗废物处置技术和管理模式优化研究。该研究是结合中国医疗废物处置技术应用和管理现状以及推进采用BAT/BEP的总体要求出发，结合具体案例提出了典型医疗废物处置技术优化所涉及工艺配置、工况参数以及污染控制要求，提出了以生命周期和全过程管理为核心的医疗废物管理理念，并就技术和管理模式优化的评价方法问题，提出了焚烧处置设施的性能评价方法以及非焚烧处理设施处理效果评价方法。 相关研究成果的意义在于可以为我国医疗废物领域相关技术选择、工程建设、设施运行、监督管理以及环境监测/检测方法的研究和应用提供借鉴，为推进医疗废物领域探索和采用BAT/BEP提供了技术支持。

Cubic sinusoidal phase mask: Another choice to extend the depth of field of incoherent imaging system

Wave-front coding is a well known technique used to extend the depth of field of incoherent imaging system. The core of this technique lies in the design of suitable phase masks, among which the most important one is the cubic phase mask suggested by Dowski and Cathey (1995) [1]. In this paper, we propose a new type called cubic sinusoidal phase mask which is generated by combing the cubic one and another component having the sinusoidal form. Numerical evaluations and real experimental results demonstrate that the composite phase mask is superior to the original cubic phase mask with parameters optimized and provides another choice to achieve the goal of depth extension. (C) 2009 Elsevier Ltd. All rights reserved.

Calculation of Hugoniot properties for shocked nitromethane based on the improved Tsien's EOS

We have calculated the Hugoniot properties of shocked nitromethane based on the improved Tsien's equation of state (EOS) that optimized by "exact" numerical molecular dynamic data at high temperatures and pressures. Comparison of the calculated results of the improved Tsien's EOS with the existed experimental data and the direct simulations show that the behavior of the improved Tsien's EOS is very good in many aspects. Because of its simple analytical form, the improved Tsien's EOS can be prospectively used to study the condensed explosive detonation coupling with chemical reaction.

Detection of Copper Ion with Laser-Induced Fluorescence in A Capillary Electrophoresis Microchip

A capillary electrophoresis microchip coupled with a confocal laser-induced fluorescence (LIF) detector was successfully constructed for the analysis of trace amounts of heavy metals in environmental sources. A new fluorescence dye, RBPhOH, synthesized from rhodamine B, was utilized in a glass microchip to selectively determine copper with high sensitivity. A series of factors including running buffer concentration, detection voltage, and sample loading time were optimized for maximum LIF detector response and, hence, method sensitivity.

Surface Initiated Polymerization from Substrates of Low Initiator Density and Its Applications in Biosensors

Surface initiated polymerization (SIP) has become an attractive method for tailoring physical and chemical properties of surfaces for a broad range of applications. Most of those application relied on the merit of a high density coating. In this study we explored a long overlooked field of SIP. SIP from substrates of low initiator density. We combined ellipsometry with AFM to investigate the effect of initiatior density and polymerization time on the morphology of polymer coatings. In addition, we carefully adjusted the nanoscale separation of polymer chains to achieve a balance between nonfouling and immobilization capacities. We further tested the performance of those coating on various biosensors, such as quartz crystal microbalance, surface plasmon resonance, and protein microarrays. The optimized matrices enhanced the performance of those biosensors. This report shall encourage researches to explore new frontiers in SIP that go beyond polymer brushes.

Optimization of evanescent wave imaging for the visualization of protein adsorption layers

We have optimized the settings of evanescent wave imaging for the visualization of a protein adsorption layer. The enhancement of the evanescent wave at the interface brought by the incident angle, the polarized state of light beam as well as a gold layer is considered. In order to improve the image contrast of a protein monolayer in experiments, we have optimized three factors-the incident angle, the polarization of light beam, and the thickness of an introduced thin gold layer with a theoretical simulation.