Microstructure evolution in CLAM steel under low cycle fatigue

In the process of room-temperature low cycle fatigue, the China Low Activation Martensitic steel exhibits at the beginning cyclic hardening and then continuous cyclic softening. The grain size decreased and the martensitic lath transformed to cells/subgrains after the tests. The subgrains increase in size with increasing strain amplitude.

Constitutive modeling, microstructure evolution, and processing map for a nitride-strengthened heat-resistant steel

A constitutive equation was established to describe the deformation behavior of a nitride-strengthened (NS) steel through isothermal compression simulation test. All the parameters in the constitutive equation including the constant and the activation energy were precisely calculated for the NS steel. The result also showed that from the stress-strain curves, there existed two different linear relationships between critical stress and critical strain in the NS steel due to the augmentation of auxiliary softening effect of the dynamic strain-induced transformation. In the calculation of processing maps, with the change of Zener-Hollomon value, three domains of different levels of workability were found, namely excellent workability region with equiaxed-grain microstructure, good workability region with “stripe” microstructure, and the poor workability region with martensitic-ferritic blend microstructure. With the increase of strain, the poor workability region first expanded, then shrank to barely existing, but appeared again at the strain of 0.6.

Microstructure, mechanical properties and fractography of heat-treated manganese steel

A Fe-8.46%Mn-0.24%Nb-0.038%C (wt.%) manganese steel was investigated. The steel has a 100% bcc structure after heat treatment at 850°C for 1.5 h, water quenching or air cooling. Martensite interlocked microstructure consisting of fine martensite plates/needles with different spatial orientations was found. Austenite forms, in small amounts, after a 600°C reheating treatment. Scanning electron microscopy images and energy dispersive spectrometry of the fracture surfaces revealed both ductile and brittle types of failure and precipitates. Deep quenching after the heat treatments does not change the phase composition or the hardness. NbC is formed in the steel, in high number densities. It plays a role in the impact fracture process, by acting as void nucleation sites, facilitating ductile fracture with dimples appearing on the fracture surface.

Microstructure, properties and application of YAl2 intermetallic compound as particle reinforcements

An yttrium aluminum (YAl2) intermetallic compound ingot was prepared in an induction furnace under vacuum. The microstructure of YAl2 ingot was characterized by optical microscopy, scanning electron microscopy, and X-ray diffraction. The load bearing response of YAl2 intermetallic was investigated and compared with SiC ceramic by indentation combined with optical microscopy and scanning electron microscopy. Additionally, the tensile properties of the Mg–Li matrix composites reinforced with ultrafine YAl2 particles fabricated by planet ball milling were tested. The results show that the intermetallic compound ingot in this experiment is composed of a main face-centered-cubic structure YAl2 phase, a small amount of YAl phase, and minor Y and Al-rich phases. YAl2 intermetallic compound has excellent stability and shows better capability in crack resistance than SiC ceramic. The YAl2 intermetallic compound has better deformation compatibility with the Mg–14Li–3Al matrix than SiC reinforcement with the matrix, which leads to the superior resistance to crack for YAl2p/Mg–14Li–3Al composite compared to SiCp/Mg–14Li–3Al composite.

An Exploration of Political Consciousness Amongst Final Year Nursing Students in Northern Ireland

Context and background
Historically nurses perceive politics and nursing as being at odds with the caring image, synonymous with nurses (Salvage, 1985). Furthermore the concept of the ‘politics of nursing’ lacks clear conceptual clarity (Hewison, 1994). This concept ranges across a continuum from political interest to participation or engagement (Rains et al, 2001). It is often argued political interest tends to be equated with knowledge/ involvement in health policy development and nurse education can foster political consciousness, through political socialization (Brown, 1996). But despite the World Health Organization (WHO, 2002) urging this involvement, nurses globally are largely absent from the political and policy making arena. What influences nurse’s political socialization and the development of a political consciousness is not clearly identified or known, although many commentators suggest the undergraduate educational environment, plays an important role (Hanley, 1987, Winter, 1991).     

AIM
The aim of this study was to explore third year nursing student’s perceptions of politics in nursing, in the context of Northern Ireland. A number of hypotheses were tested examining the relationship between age, prior educational attainment and political interest and attitudes.  

Research methodology
A cross sectional research design was used and the data was collected using a short anonymous self-completion web survey (Bryman, 2012). The sample was a convenience sample of one cohort of final year adult nursing students (n154) in one Northern Irish university, with a 42% response rate. Data was analyzed using SPSS.

Key findings and conclusions
The results revealed 55% of students were very/fairly interested in politics, with 6% reporting no interest in politics. 85% of students were registered to vote, but only 48% voted in the 2010 N Ireland Assembly election.   
Recommend inclusion of a unit of study incorporating innovative teaching methods related to politics and health related policy, in the undergraduate nursing programme.       

Trends in material choice for direct restorations by final year students from University College Cork 2004-2009

Traditionally, undergraduate students in University College Cork (UCC) have been taught to use amalgam as the first choice material for direct restoration of posterior cavities. Since 2005 the use of composite resins has replaced amalgam as the first choice material. An audit was conducted of all direct restorations placed by final year students from UCC from 2004 until 2009. Results showed that over a six year period, final year UCC dental undergraduate students placed proportionately more direct composite resin restorations and significantly fewer amalgam restorations. The need for and undergraduate exposure to, provision of amalgam restorations may have to be revisited.

Study on risk assessment and management and prevention of conflicts of interest in the prevention and fight against betting-related match fixing in the EU 28: Final Report

This report concerns the provisions and practices on betting-related match fixing in sports
within the 28 Member States. Carried out in late 2013/early 2014, respondents in each Member
State reported on that state’s gambling-related provisions in respect of football and tennis and
(in each country) a third sport determined on the basis of either its popularity (in terms of
participation or television viewing) or the existence of betting-related “scandals” in that sport
within that particular jurisdiction. Those reports helped the authors to compare the Member
States’ regulatory and self-regulatory frameworks relating to risk assessment and conflict of
interest management, with a view to indicating areas of best practice, identifying particularly
good legislative frameworks and highlighting areas where change was either desirable or
necessary. While some individual Member States have legislation which might provide
templates that others could adapt for their own use, the authors were not convinced that “more
law”, whether at the national or European level, was desirable. Rather, more effective
cooperation among the stakeholders was identified as being more likely to provide tangible
benefits than would new legal frameworks.

Critical evaluation of pulse-echo ultrasonic test method for the determination of setting and mechanical properties of acrylic bone cement: Influence of mixing technique

Currently there is no reliable objective method to quantify the setting properties of acrylic bone cements within an operating theatre environment. Ultrasonic technology can be used to determine the acoustic properties of the polymerising bone cement, which are linked to material properties and provide indications of the physical and chemical changes occurring within the cement. The focus of this study was the critical evaluation of pulse-echo ultrasonic test method in determining the setting and mechanical properties of three different acrylic bone cement when prepared under atmospheric and vacuum mixing conditions. Results indicated that the ultrasonic pulse-echo technique provided a highly reproducible and accurate method of monitoring the polymerisation reaction and indicating the principal setting parameters when compared to ISO 5833 standard, irrespective of the acrylic bone cement or mixing method used. However, applying the same test method to predict the final mechanical properties of acrylic bone cement did not prove a wholly accurate approach. Inhomogeneities within the cement microstructure and specimen geometry were found to have a significant influence on mechanical property predictions. Consideration of all the results suggests that the non-invasive and non-destructive pulse-echo ultrasonic test method is an effective and reliable method for following the full polymerisation reaction of acrylic bone cement in real-time and then determining the setting properties within a surgical theatre environment. However the application of similar technology for predicting the final mechanical properties of acrylic bone cement on a consistent basis may prove difficult.

Optimisation of a two-liquid component pre-filled acrylic bone cement system: A design of experiments approach to optimise cement final properties

The initial composition of acrylic bone cement along with the mixing and delivery technique used can influence its final properties and therefore its clinical success in vivo. The polymerisation of acrylic bone cement is complex with a number of processes happening simultaneously. Acrylic bone cement mixing and delivery systems have undergone several design changes in their advancement, although the cement constituents themselves have remained unchanged since they were first used. This study was conducted to determine the factors that had the greatest effect on the final properties of acrylic bone cement using a pre-filled bone cement mixing and delivery system. A design of experiments (DoE) approach was used to determine the impact of the factors associated with this mixing and delivery method on the final properties of the cement produced. The DoE illustrated that all factors present within this study had a significant impact on the final properties of the cement. An optimum cement composition was hypothesised and tested. This optimum recipe produced cement with final mechanical and thermal properties within the clinical guidelines and stated by ISO 5833 (International Standard Organisation (ISO), International standard 5833: implants for surgery—acrylic resin cements, 2002), however the low setting times observed would not be clinically viable and could result in complications during the surgical technique. As a result further development would be required to improve the setting time of the cement in order for it to be deemed suitable for use in total joint replacement surgery.

Microstructure and dielectric properties of epitaxial BaTiO3 films and BaTiO3/SrTiO3 multilayers

Epitaxial BaTiO3 films and BaTiO3/SrTiO3 multilayers were grown by pulsed laser deposition (PLD) on (001)-oriented Nb-doped SrTiO3 (SrTiO3:Nb) substrates. Measurements of the dielectric properties were performed comparing BaTiO3 films and BaTiO3/SrTiO3 multilayers of different number of individual layers, but equal overall thickness. The dielectric loss saturates for a thickness above 300 nm, and linearly decreases with decreasing film thickness below a thickness of 75 nm, and it is independent on the number of multilayers, pointing to some interface effect. The thickness dependence of the dielectric constant of BaTiO3 films and BaTiO3/SrTiO3 multilayers; exhibits a change in the linear slope at a thickness of 75 nm. This behavior is explained by the change observed in the morphology at a thickness of 75 nm. In order to explain the thickness dependence of the dielectric constant, two approaches are considered in this paper, viz. a "series capacitor" model and a "dead layer" model.