Magnetic properties of selected 3d- and 4f-systems on alpha-Al 2 O 3 substrates

In this work the growth and the magnetic properties of the transition metals molybdenum, niobium, and iron and of the highly-magnetostrictive C15 Laves phases of the RFe2 compounds (R: Rare earth metals: here Tb, Dy, and Tb{0.3}Dy{0.7} deposited on alpha-Al2O3 (sapphire) substrates are analyzed. Next to (11-20) (a-plane) oriented sapphire substrates mainly (10-10) (m-plane) oriented substrates were used. These show a pronounced facetting after high temperature annealing in air. Atomic force microscopy (AFM) measurements reveal a dependence of the height, width, and angle of the facets with the annealing temperature. The observed deviations of the facet angles with respect to the theoretical values of the sapphire (10-1-2) and (10-11) surfaces are explained by cross section high resolution transmission electron microscopy (HR-TEM) measurements. These show the plain formation of the (10-11) surface while the second, energy reduced (10-1-2) facet has a curved shape given by atomic steps of (10-1-2) layers and is formed completely solely at the facet ridges and valleys. Thin films of Mo and Nb, respectively, deposited by means of molecular beam epitaxy (MBE) reveal a non-twinned, (211)-oriented epitaxial growth as well on non-faceted as on faceted sapphire m-plane, as was shown by X-Ray and TEM evaluations. In the case of faceted sapphire the two bcc crystals overgrow the facets homogeneously. Here, the bcc (111) surface is nearly parallel to the sapphire (10-11) facet and the Mo/Nb (100) surface is nearly parallel to the sapphire (10-1-2) surface. (211)-oriented Nb templates on sapphire m-plane can be used for the non-twinned, (211)-oriented growth of RFe2 films by means of MBE. Again, the quality of the RFe2 films grown on faceted sapphire is almost equal to films on the non-faceted substrate. For comparison thin RFe2 films of the established (110) and (111) orientation were prepared. Magnetic and magnetoelastic measurements performed in a self designed setup reveal a high quality of the samples. No difference between samples with undulated and flat morphology can be observed. In addition to the preparation of covering, undulating thin films on faceted sapphire m-plane nanoscopic structures of Nb and Fe were prepared by shallow incidence MBE. The formation of the nanostructures can be explained by a shadowing of the atomic beam due to the facets in addition to de-wetting effects of the metals on the heated sapphire surface. Accordingly, the nanostructures form at the facet ridges and overgrow them. The morphology of the structures can be varied by deposition conditions as was shown for Fe. The shape of the structures vary from pearl-necklet strung spherical nanodots with a diameter of a few 10 nm to oval nanodots of a few 100 nm length to continuous nanowires. Magnetization measurements reveal uniaxial magnetic anisotropy with the easy axis of magnetization parallel to the facet ridges. The shape of the hysteresis is depending on the morphology of the structures. The magnetization reversal processes of the spherical and oval nanodots were simulated by micromagnetic modelling and can be explained by the formation of magnetic vortices.

Weiterentwicklung einer Produktionsanlage und der Speicherungs- bzw. Transportkonzepte für hochpolarisiertes 3He

Der Bedarf an hyperpolarisiertem 3He in Medizin und physikalischer Grundlagenforschung ist in den letzten ca. 10-15 Jahren sowohl in Bezug auf die zu Verfügung stehende Menge, als auch auf den benötigten Grad der Kernspinpolarisation stetig gestiegen. Gleichzeitig mußten Lösungen für die polarisationserhaltende Speicherung und den Transport gefunden werden, die je nach Anwendung anzupassen waren. Als Ergebnis kann mit dieser Arbeit ein in sich geschlossenes Gesamtkonzept vorgestellt werden, daß sowohl die entsprechenden Mengen für klinische Anwendungen, als auch höchste Polarisation für physikalische Grundlagenfor-schung zur Verfügung stellen kann. Verschiedene unabhängige Polarimetriemethoden zeigten in sich konsistente Ergebnisse und konnten, neben ihrer eigenen Weiterentwicklung, zu einer verläßlichen Charakterisierung des neuen Systems und auch der Transportzellen und –boxen eingesetzt werden. Die Polarisation wird mittels „Metastabilem Optischen Pumpen“ bei einem Druck von 1 mbar erzeugt. Dabei werden ohne Gasfluß Werte von P = 84% erreicht. Im Flußbetrieb sinkt die erreichbare Polarisation auf P ≈ 77%. Das 3He kann dann weitgehend ohne Polarisationsver-luste auf mehrere bar komprimiert und zu den jeweiligen Experimenten transportiert werden. Durch konsequente Weiterentwicklung der vorgestellten Polarisationseinheit an fast allen Komponenten kann somit jetzt bei einem Fluß von 0,8 barl/h eine Polarisation von Pmax = 77% am Auslaß der Apparatur erreicht werden. Diese skaliert linear mit dem Fluß, sodaß bei 3 barl/h die Polarisation immer noch bei ca. 60% liegt. Dabei waren die im Rahmen dieser Arbeit durchgeführten Verbesserungen an den Lasern, der Optik, der Kompressionseinheit, dem Zwischenspeicher und der Gasreinigung wesentlich für das Erreichen dieser Polarisatio-nen. Neben dem Einsatz eines neuen Faserlasersystems ist die hohe Gasreinheit und die lang-lebige Kompressionseinheit ein Schlüssel für diese Leistungsfähigkeit. Seit Herbst 2001 er-zeugte das System bereits über 2000 barl hochpolarisiertes 3He und ermöglichte damit zahl-reiche interdisziplinäre Experimente und Untersuchungen. Durch Verbesserungen an als Prototypen bereits vorhandenen Transportboxen und durch weitgehende Unterdrückung der Wandrelaxation in den Transportgefäßen aufgrund neuer Erkenntnisse über deren Ursachen stellen auch polarisationserhaltende Transporte über große Strecken kein Problem mehr dar. In unbeschichteten 1 Liter Kolben aus Aluminosilikatglä-sern werden nun problemlos Speicherzeiten von T1 > 200h erreicht. Im Rahmen des europäi-schen Forschungsprojektes „Polarized Helium to Image the Lung“ wurden während 19 Liefe-rungen 70barl 3He nach Sheffield (UK) und bei 13 Transporten 100 barl nach Kopenhagen (DK) per Flugzeug transportiert. Zusammenfassend konnte gezeigt werden, daß die Problematik der Kernspinpolarisationser-zeugung von 3He, die Speicherung, der Transport und die Verwendung des polarisierten Ga-ses in klinischer Diagnostik und physikalischen Grundlagenexperimenten weitgehend gelöst ist und das Gesamtkonzept die Voraussetzungen für allgemeine Anwendungen auf diesen Gebieten geschaffen hat.

Mathematische Aspekte des Ferromagnetismus im HFz-Hubbardmodell

Mit dem HFz-Hubbardmodell meinen wir das übliche Hubbardmodell für alle Dimensionen mit der Einschränkung auf die Menge der Slaterdeterminanten, wobei allerdings die Spinwellen dieser Slaterdeterminanten nur Bewegung parallel zur z-Richtung haben. Für dieses Modell mit kleiner Füllung ist es uns gelungen zu beweisen, dass der Ferromagnetismus für große, aber endliche Kopplung entsteht.

Computer-Simulationen zur Strukturbildung von einzelnen Polymerketten

In dieser Arbeit wurden die Phasenübergänge einer einzelnen Polymerkette mit Hilfe der Monte Carlo Methode untersucht. Das Bondfluktuationsmodell wurde zur Simulation benutzt, wobei ein attraktives Kastenpotential zwischen allen Monomeren der Polymerkette gewirkt hat. Drei Arten von Bewegungen sind eingeführt worden, um die Polymerkette richtig zu relaxieren. Diese sind die Hüpfbewegung, die Reptationsbewegung und die Pivotbewegung. Um die Volumenausschlußwechselwirkung zu prüfen und um die Anzahl der Nachbarn jedes Monomers zu bestimmen ist ein hierarchischer Suchalgorithmus eingeführt worden. Die Zustandsdichte des Modells ist mittels des Wang-Landau Algorithmus bestimmt worden. Damit sind thermodynamische Größen berechnet worden, um die Phasenübergänge der einzelnen Polymerkette zu studieren. Wir haben zuerst eine freie Polymerkette untersucht. Der Knäuel-Kügelchen Übergang zeigt sich als ein kontinuierlicher Übergang, bei dem der Knäuel zum Kügelchen zusammenfällt. Der Kügelchen-Kügelchen Übergang bei niedrigeren Temperaturen ist ein Phasenübergang der ersten Ordnung, mit einer Koexistenz des flüssigen und festen Kügelchens, das eine kristalline Struktur hat. Im thermodynamischen Limes sind die Übergangstemperaturen identisch. Das entspricht einem Verschwinden der flüssigen Phase. In zwei Dimensionen zeigt das Modell einen kontinuierlichen Knäuel-Kügelchen Übergang mit einer lokal geordneten Struktur. Wir haben ferner einen Polymermushroom, das ist eine verankerte Polymerkette, zwischen zwei repulsiven Wänden im Abstand D untersucht. Das Phasenverhalten der Polymerkette zeigt einen dimensionalen crossover. Sowohl die Verankerung als auch die Beschränkung fördern den Knäuel-Kügelchen Übergang, wobei es eine Symmetriebrechung gibt, da die Ausdehnung der Polymerkette parallel zu den Wänden schneller schrumpft als die senkrecht zu den Wänden. Die Beschränkung hindert den Kügelchen-Kügelchen Übergang, wobei die Verankerung keinen Einfluss zu haben scheint. Die Übergangstemperaturen im thermodynamischen Limes sind wiederum identisch im Rahmen des Fehlers. Die spezifische Wärme des gleichen Modells aber mit einem abstoßendem Kastenpotential zeigt eine Schottky Anomalie, typisch für ein Zwei-Niveau System.

A structural and metamorphic study of the southern Menderes Massif (Western Turkey)

P-T conditions, paragenetic studies and the relation between mineral growth, deformation and - when possible- isograd minerals have been used to describe the type of metamorphism involved within lower units of the southern Menderes Massif of the Anatolide Belt in western Turkey. The study areas mainly consist of Proterozoic orthogneiss and surrounding schists of presumed Paleozoic age. Both units are seen as nappes in the southern study area, the Çine and the Selimiye nappe, on the whole corresponding to Proterozoic orthogneiss and surrounding schists, respectively. The Çine and Selimiye nappes are part of a complex geological structure within the core series of the Menderes Massif. Their emplacement under lower greenschist facies conditions, would result from closure of the northern Neo-Thethys branch during the Eocene. These two nappes are separated by a major tectonic structure, the Selimiye shear zone, which records top-to-the-S shearing under greenschist facies conditions. Amphibolite to upper amphibolite facies metamorphism is widely developed within the metasedimentary rocks of the Çine nappe whereas no metamorphism exceeding lower amphibolite facies has been observed in the Selimiye nappe. In the southern margin of the Çine Massif, around Selimiye and Millas villages, detailed sampling has been undertaken in order to map mineral isograds within the Selimiye nappe and to specify P-T conditions in this area. The data collected in this area reveals a global prograde normal erosion field gradient from south to north and toward the orthogneiss. The mineralogical parageneses and P-T estimates are correlated with Barrovian-type metamorphism. A jump of P-T conditions across the Selimiye shear zone has been identified and estimated c. 2 kbar and 100 °C which evidences the presence of amphibolite facies metasedimentary rocks near the orthogneiss. Metasedimentary rocks from the overlying Selimiye nappe have maximum P-T conditions of c. 4-5 kbar and c. 525 °C near the base of the nappe. Metasedimentary rocks from the Çine nappe underneath the Selimiye shear zone record maximum P-T conditions of about 7 kbar and >550 °C. Kinematic indicators in both nappes consistently show a top-S shear sense. Metamorphic grade in the Selimiye nappe decreases structurally upwards as indicated by mineral isograds defining the garnet-chlorite zone at the base, the chloritoid-biotite zone and the biotite-chlorite zone at the top of the nappe. The mineral isograds in the Selimiye nappe run parallel to the regional SR foliation. 40Ar/39Ar mica ages indicate an Eocene age of metamorphism in the Selimiye nappe and underneath the Çine nappe in this area. Metasedimentary rocks of the Çine nappe 20-30 km north of the Selimiye shear zone record maximum P-T conditions of 8-11 kbar and 600-650 °C. Kinematic indicators show mainly top-N shear sense associated with prograde amphibolite facies metamorphism. An age of about 550 Ma could be indicated for amphibolite facies metamorphism and associated top-N shear in the orthogneiss and metasedimentary rocks of the Çine nappe. However, there is no evidence for polymetamorphism in the 6 metasedimentary rocks of the Çine nappe, making tectonic interpretations about late Neoproterozoic to Cambrian and Tertiary metamorphic events speculative. In the western margin of the Çine Massif metamorphic mineral parageneses and pressure– temperature conditions lead to similar conclusion regarding the erosion field gradient, prograde normal toward the orthogneiss. The contact between orthogneiss and surrounding metasedimentary rocks is mylonitic and syn-metamorphism. P-T estimates are those already observed within the Selimiye nappe and correlated with lower amphibolite facies parageneses. Finally additional data in the eastern part and a general paragenetic study within the Menderes Massif lower units, the Çine and the Selimiye nappes, strongly suggest a single Barrovian-type metamorphism predating Eocene emplacement of the high pressure–low temperature Lycean and Cycladic blueschist nappes. Metamorphic mineral parageneses and pressure–temperature conditions do not support the recently proposed model of high pressure–low temperature metamorphic overprinting, which implies burial of the lower units of the Menderes Massif up to depth of 30 km, as a result of closure of the Neo-Tethys. According to the geochronological problem outlined during this thesis, there are two possible schemes: either Barrovian-type metamorphism is Proterozoic in age and part of the sediments from Selimiye nappe (lower amphibolite facies) has to be proterozoic of age too, or Barrovian-type metamorphism in Eocene of age. In the first case the structure observed now in the core series would correspond to simple exhumation of Proterozoic basement. In the latter case a possible correlation with closure of Neo-Tethys (sensu stricto, southern branch) is envisaged.

Generierung und Charakterisierung von rekombinanten Cytomegaloviren mit Punktmutationen in antigenen Peptiden

Die Kontrolle der produktiven Cytomegalovirus- (CMV) Infektion ist von der effizienten Rekonstitution antiviraler CD8 T-Zellen abhängig. Dies führt jedoch nicht zur vollständigen Eliminierung des viralen Genoms aus den Zielorganen, sondern das Virus verbleibt in einem nicht-replikativen Zustand: der Latenz. Es ist bekannt, dass während der Latenz nur ein geringer Anteil latenter mCMV-Genome in der Lunge die Major Immediate Early (MIE) Gene ie1 und ie2 exprimiert, die Latenz aber dennoch bestehen bleibt, weil das differentielle Splicing des primären IE1/3-Transkripts zum Transaktivator-Transkript IE3 nicht erfolgt. Damit war neben der Initiation der IE-Genexpression am MIE-Promotor-Enhancer das IE1/3-Splicing als zweiter molekularer Latenz-Kontrollpunkt identifiziert. Parallel zur Latenz-assoziierten IE1-Genexpression sind in der Lunge aktivierte CD62L-low CD8 T-Zellen mit Spezifität für das immundominante IE1-Peptid 168-YPHFMPTNL-176 angereichert. Dies legte die Hypothese nahe, dass neben der molekularen Kontrolle der Latenz auch eine immunologische Kontrolle, beispielsweise durch IE1-Epitop-spezifische CD8 T-Zellen besteht. Zur Evaluierung dieser Hypothese wurde in der vorliegenden Arbeit mittels BAC-Mutagenese erstmals ein rekombinantes mCMV generiert, in dem das IE1-Peptid durch Punktmutation der C-terminalen MHC-Ankeraminosäure L176A zerstört ist. Dazu musste zunächst die Technik der BAC-Mutagenese herpesviraler Genome (in Anlehnung an die publizierten Arbeiten von Messerle et al., 1997; Borst et al., 1999, 2004; Wagner et al., 1999) in der Arbeitsgruppe etabliert werden. Neben der Funktionsverlust-Mutante (mCMV-IE1-L176A) wurden zur Kontrolle zwei Revertanten (mCMV-IE1-A176L und mCMV-IE1-A176L*) generiert. In letzterer, als Wobble-Revertante bezeichnet, wird wieder die authentische MHC-Ankeraminosäure L eingesetzt, es verbleibt aber ein singulärer Nukleotidaustausch A->T in der Wobble-Position des Codons als Marker zur Unterscheidung zum WT-mCMV zurück. Der immunologische Phänotyp der Funktionsverlust-Mutante, also die funktionelle Auslöschung des antigenen IE1-Peptids im Priming einer CD8 T-Zell-Antwort, entsprach der Erwartung. Entsprechend konnte nach Infektion mit der Funktionsverlust-Mutante keine Reaktivität gegen das IE1-Peptid nachgewiesen werden. In den Revertanten hingegen war die Erkennung des IE1-Peptids wieder hergestellt. Die Ergebnisse dieser Arbeit zeigen weiter, dass die Funktionsverlust-Mutante sowie die Revertanten ohne signifikante Beeinflussung in vitro in permissiven Fibroblasten und in vivo in verschiedenen Geweben replizieren. Wie aktuelle Daten nach Knochenmarktransplantation und Infektion mit der Funktionsverlust-Mutante im Vergleich zu den Revertanten zeigen, ist die Frequenz Latenz-assoziierter IE1-Transkriptionsereignisse bei der Funktionsverlust-Mutante signifikant erhöht. Damit konnte erstmalig der Beweis für eine Kontrolle der Latenz-assoziierten IE1-Genexpression durch IE1-Epitop-spezifische CD8 T-Zellen und damit für eine Präsentation des IE1-Peptids während der Latenz erbracht werden.

Rod-coil copolymer structures

Skalenargumente werden verwendet, um Rod-Coil Copolymere mit fester Zusammensetzung von steifen Stäbchen und flexiblen Ketten zu studieren. In einem selektiven Lösungsmittel, in dem sich nur die Ketten lösen, bildet ein Rod-Coil Multiblock zylinderförmige Micellen aus aggregierten Stäbchen verbunden durch Kettenstücke. Die Stäbchen aggregieren, um Energie zu gewinnen. Dieser Prozeß wird durch den Entropieverlust der flexiblen Ketten ausgeglichen. Das Adsorptionsverhalten von Aggregaten aus parallel aneinandergelagerten, einzelnen Rod-Coil Diblöcken in selektivem Lösungsmittel wird anhand von erweiterten Skalenbetrachtungen diskutiert. Wenn ein solches Aggregat mit den Stäbchen parallel zur Oberfläche adsorbiert, verschieben sich die Stäbchen gegeneinander. Zusätzlich werden die Stabilität der adsorbierten Aggregate und andere mögliche Konfigurationen untersucht. Um einen Rod-Coil Multiblock mit variabler Zusammensetzung zu studieren, wird eine Feldtheorie entwickelt. Jedes Segment kann entweder steif oder flexibel sein. Das System zeigt drei Phasenzustände, offene Kette, amorphe Globule und flüssig-kristalline Globule. Beim Übergang von amorpher zu flüssig-kristalliner Globule steigt der Anteil an steifen Segmenten rapide an. Dieser Übergang wird durch die isotrope Wechselwirkung zwischen den steifen Segmenten und die anisotrope Oberflächenenergie der Globule verursacht.

Modeling of complex chemical reactions and macromolecular orientation phenomena in confined geometries

The cooperative motion algorithm was applied on the molecular simulation of complex chemical reactions and macromolecular orientation phenomena in confined geometries. First, we investigated the case of equilibrium step-growth polymerization in lamellae, pores and droplets. In such systems, confinement was quantified as the area/volume ratio. Results showed that, as confinement increases, polymerization becomes slower and the average molecular weight (MW) at equilibrium decreases. This is caused by the sterical hindrance imposed by the walls since chain growth reactions in their close vicinity have less realization possibilities. For reactions inside droplets at surfaces, contact angles usually increased after polymerization to compensate conformation restrictions imposed by confinement upon growing chains. In a second investigation, we considered monodisperse and chemically inert chains and focused on the effect of confinement on chain orientation. Simulations of thin polymer films showed that chains are preferably oriented parallel to the surface. Orientation increases as MW increases or as film thickness d decreases, in qualitative agreement with experiments with low MW polystyrene. It is demonstrated that the orientation of simulated chains results from a size effect, being a function of the ratio between chain end-to-end distance and d. This study was complemented by experiments with thin films of pi-conjugated polymers like MEH-PPV. Anisotropic refractive index measurements were used to analyze chain orientation. With increasing MW, orientation is enhanced. However, for MEH-PPV, orientation does not depend on d even at thicknesses much larger than the chain contour length. This contradiction with simulations was discussed by considering additional causes for orientation, for instance the appearance of nematic-like ordering in polymer films. In another investigation, we simulated droplet evaporation at soluble surfaces and reproduced the formation of wells surrounded by ringlike deposits at the surface, as observed experimentally. In our simulations, swollen substrate particles migrate to the border of the droplet to minimize the contact between solvent and vacuum, which costs the most energy. Deposit formation in the beginning of evaporation results in pinning of the droplet. When polymer chains at the substrate surface have strong uniaxial orientation, the resulting pattern is no longer similar to a ring but to a pair of half-moons. In a final stage, as an extension for the model developed for polymerization in nanoreactors, we studied the effect of geometrical confinement on a hypothetical oscillating reaction following the mechanism of the so called periodically forced Brusselator. It was shown that a reaction which is chaotic in the bulk may be driven to periodicity by confinement and vice-versa, opening new perspectives for chaos control.

Pratiche del possibile: i Participatory Guarantee Systems e le scelte d'acquisto del consumatore brasiliano

Negli ultimi anni, parallelamente all’espansione del settore biologico, si è assistito a un crescente interesse per i modelli alternativi di garanzia dell’integrità e della genuinità dei prodotti biologici. Gruppi di piccoli agricoltori di tutto il mondo hanno iniziato a sviluppare approcci alternativi per affrontare i problemi connessi alla certificazione di terza parte. Queste pratiche sono note come Sistemi di Garanzia Partecipativa (PGS). Tali modelli: (i) si basano sugli standard di certificazione biologica dell’IFOAM, (ii) riguardano il complesso dei produttori di una comunità rurale, (iii) comportano l’inclusione di una grande varietà di attori e (iv) hanno lo scopo di ridurre al minimo burocrazia e costi semplificando le procedure di verifica e incorporando un elemento di educazione ambientale e sociale sia per i produttori sia per i consumatori. Gli obiettivi di questo lavoro di ricerca: • descrivere il funzionamento dei sistemi di garanzia partecipativa; • indicare i vantaggi della loro adozione nei Paesi in via di sviluppo e non; • illustrare il caso della Rede Ecovida de Agroecologia (Brasile); • offrire uno spunto di riflessione che riguarda il consumatore e la relativa fiducia nel modello PGS. L’impianto teorico fa riferimento alla Teoria delle Convenzioni. Sulla base del quadro teorico è stato costruito un questionario per i consumatori con lo scopo di testare l’appropriatezza delle ipotesi teoriche. I risultati finali riguardano la stima del livello di conoscenza attuale, la fiducia e la volontà d’acquisto dei prodotti PGS da parte dei consumatori nelle aree considerate. Sulla base di questa ricerca sarà possibile adattare ed esportare il modello empirico in altri paesi che presentano economie diverse per cercare di comprendere il potenziale campo di applicazione dei sistemi di garanzia partecipativa.

Sulfur isotope analysis of aerosol particles by NanoSIMS

A new method to measure the sulfur isotopic composition of individual aerosol particles by NanoSIMS has been developed and tested on several standards such as barite (BaSO4), anhydrite (CaSO4), gypsum (CaSO4·2H2O), mascagnite ((NH4)2SO4), epsomite (MgSO4·7H2O), magnesium sulfate (MgSO4·xH2O), thenardite (Na2SO4), boetite (K2SO4) and cysteine (an amino acid). This ion microprobe technique employs a Cs+ primary ion beam and measures negative secondary ions permitting the analysis of sulfur isotope ratios in individual aerosol particles down to 500 nm in size (0.001-0.5 ng of sample material). The grain-to-grain reproducibility of measurements is typically 5‰ (1σ) for micron-sized grains, <5‰ for submicron-sized grains, and <2‰ for polished thin sections and ultra microtome sections which were studied for comparison. The role of chemical omposition (matrix effect) and sample preparation techniques on the instrumental mass fractionation (IMF) of the 34S/32S ratio in the NanoSIMS has been investigated. The IMF varies by ~15‰ between the standards studied here. A good correlation between IMF and ionic radius of the cations in sulfates was observed. This permits to infer IMF corrections even for sulfates for which no isotope standards are available. The new technique allows to identify different types of primary and secondary sulfates based on their chemical composition and to measure their isotopic signature separately. It was applied to marine aerosol samples collected in Mace Head and urban aerosol samples collected in Mainz. It was shown that primary sulfate particles such as sulfate in NaCl or gypsum particles precipitated from ocean water retain the original isotopic signature of their source. The isotopic composition of secondary sulfate depends on the isotopic composition of precursor SO2 and the oxidation pathway. The 34S/32S fractionation with respect to the precursor SO2 is -9‰ for homogeneous oxidation and +16.5‰ for heterogeneous oxidation. This large difference between the isotopic fractionation of both pathways allows identifying the oxidation pathway from which the SO42- in a secondary sulfate particle is derived, by means of its sulfur isotope ratio, provided that the isotopic signature of the precursor SO2 is known. The isotopic composition of the precursor SO2 of secondary sulfates was calculated based on the isotopic composition of particles with known oxidation pathway such as fine mode ammonium sulfate.

Detection of small buried objects: asymptotic factorization and MUSIC

In this work, we consider a simple model problem for the electromagnetic exploration of small perfectly conducting objects buried within the lower halfspace of an unbounded two–layered background medium. In possible applications, such as, e.g., humanitarian demining, the two layers would correspond to air and soil. Moving a set of electric devices parallel to the surface of ground to generate a time–harmonic field, the induced field is measured within the same devices. The goal is to retrieve information about buried scatterers from these data. In mathematical terms, we are concerned with the analysis and numerical solution of the inverse scattering problem to reconstruct the number and the positions of a collection of finitely many small perfectly conducting scatterers buried within the lower halfspace of an unbounded two–layered background medium from near field measurements of time–harmonic electromagnetic waves. For this purpose, we first study the corresponding direct scattering problem in detail and derive an asymptotic expansion of the scattered field as the size of the scatterers tends to zero. Then, we use this expansion to justify a noniterative MUSIC–type reconstruction method for the solution of the inverse scattering problem. We propose a numerical implementation of this reconstruction method and provide a series of numerical experiments.

Noble-metal nanoparticles produced with colloidal lithography: fabrication, optical properties and applications

In this work, metal nanoparticles produced by nanosphere lithography were studied in terms of their optical properties (in connection to their plasmon resonances), their potential application in sensing platforms - for thin layer sensing and bio-recognition events -, and for a particular case (the nanocrescents), for enhanced spectroscopy studies. The general preparation procedures introduced early in 2005 by Shumaker-Parry et al. to produce metallic nanocrescents were extended to give rise to more complex (isolated) structures, and also, by combining colloidal monolayer fabrication and plasma etching techniques, to arrays of them. The fabrication methods presented in this work were extended not only to new shapes or arrangements of particles, but included also a targeted surface tailoring of the substrates and the structures, using different thiol and silane compounds as linkers for further attachment of, i.e. polyelectrolyte layers, which allow for a controlled tailoring of their nanoenvironment. The optical properties of the nanocrescents were studied with conventional transmission spectroscopy; a simple multipole model was adapted to explain their behaviour qualitatively. In terms of applications, the results on thin film sensing using these particles show that the crescents present an interesting mode-dependent sensitivity and spatial extension. Parallel to this, the penetrations depths were modeled with two simplified schemes, obtaining good agreement with theory. The multiple modes of the particles with their characteristic decay lengths and sensitivities represent a major improvement for particle-sensing platforms compared to previous single resonance systems. The nanocrescents were also used to alter the emission properties of fluorophores placed close to them. In this work, green emitting dyes were placed at controlled distances from the structures and excited using a pulsed laser emitting in the near infrared. The fluorescence signal obtained in this manner should be connected to a two-photon processes triggered by these structures; obtaining first insight into plasmon-mediated enhancement phenomena. An even simpler and faster approach to produce plasmonic structures than that for the crescents was tested. Metallic nanodiscs and nanoellipses were produced by means of nanosphere lithography, extending a procedure reported in the literature to new shapes and optical properties. The optical properties of these particles were characterized by extinction spectroscopy and compared to results from the literature. Their major advantage is that they present a polarization-dependent response, like the nanocrescents, but are much simpler to fabricate, and the resonances can be tailored in the visible with relative ease. The sensing capabilities of the metallic nanodiscs were explored in the same manner as for the nanocrescents, meaning their response to thin layers and to bio-recognition events on their surface. The sensitivity of these nanostructures to thin films proved to be lower than that of the crescents, though in the same order of magnitude. Experimental information about the near field extension for the Au nanodiscs of different sizes was also extracted from these measurements. Further resonance-tailoring approaches based on electrochemical deposition of metals on the nanodiscs were explored, as a means of modifying plasmon resonances by changing surface properties of the nanoparticles. First results on these experiments would indicate that the deposition of Ag on Au on a submonolayer coverage level can lead to important blue-shifts in the resonances, which would open a simple way to tailor resonances by changing material properties in a local manner.

A sampling method for detecting buried objects using electromagnetic scattering

We consider a simple (but fully three-dimensional) mathematical model for the electromagnetic exploration of buried, perfect electrically conducting objects within the soil underground. Moving an electric device parallel to the ground at constant height in order to generate a magnetic field, we measure the induced magnetic field within the device, and factor the underlying mathematics into a product of three operations which correspond to the primary excitation, some kind of reflection on the surface of the buried object(s) and the corresponding secondary excitation, respectively. Using this factorization we are able to give a justification of the so-called sampling method from inverse scattering theory for this particular set-up.

Host immune response in immunodeficient mice against infection with Cryptosporidium parvum

Immunantwort von immundefizienten Mäusen gegenüber Infektionen mit Cryptosporidium parvum. Cryptosporidium parvum ist ein intrazellulärer, protozoischer Krankheitserreger, der im immunkompromittierten Wirt zu lebensbedrohender Enteritis führen kann. CD4+ T-Zellen und Interferon (IFN)-γ spielen wesentliche Rollen bei der Wirtsimmunantwort gegen die Infektion. Dennoch sind die Effektormechanismen, die zur Resistenz führen nur wenig verstanden. In dieser Studie wurde die Immunantwort von IFN-γ- und Interleukin (IL)-12-Defektmäusen parallel zu Wildtypmäusen analysiert. Die Ergebnisse identifizierten IFN-γ als Schlüsselzytokin bei der natürlichen und erworbenen Immunität während der Erst- und Folgeinfektion mit C. parvum. Tumornekrosefaktor (TNF)-α ist möglicherweise ein Induktor der frühen IFN-γ-Antwort in IL-12 Knockout-Mäusen. Weiterhin tragen offenbar sowohl Th1- als auch Th2-Zytokine zur Überwindung der Primärinfektion bei, die ersten mehr als die letztgenannten. Zytokingene waren am Ort der Infektion (Ileum) dramatisch verändert, nicht aber in den lokalen Lymphknoten und der Milz. Nach Folgeinfektion ergab sich in Abwesenheit von IFN-γ eine signifikante Erhöhung der Th2-Zytokine IL-5 and IL-13. Die Ergebnisse zeigten weiterhin, dass das Th1-Zytokin IL-18 zur Resistenz gegenüber C. parvum beiträgt, möglicherweise durch verschiedene Immunfunktionen, wie der Regulation von Serum-IFN-γ während der Infektion und/oder der Erhaltung der Homeostase der Th1/Th2-Zytokine durch Regulation der Th2-Zytokine. Weiterhin zeigten diese Untersuchungen den Transfer von Resistenz gegenüber C. parvum von infizierten auf naïve Mäuse mittels stimulierter intraepithelialer Lymphozyten und CD4+ T-Zellen. Diese Ergebnisse weisen auf die Gegenwart von C. parvum-spezifischen CD4+ T-Zellen in anderen lymphatischen Geweben neben der Darmmukosa hin. Eine Stimulation der Spendertiere durch Infektion war notwendig für eine übertragbare schützende Immunität. Dennoch konnte die übertragene Immunität nicht die Infektion der Empfängertiere vollständig verhindern; eine Verdopplung der Spenderzellen führte zu keinem besseren Ergebnis. Weiterhin ergab der Transfer von CD4+ und CD8+ T-Zellen (Pan-T-Zellen) keinen erhöhten Schutz der naiven Empfängertiere als der alleinige Transfer von CD4+ T-Zellen. Dies weist auf die fehlende Bedeutung der CD8+ T-Zellen beim Schutz vor C. parvum-Infektion hin.

Polymer-liquid crystal interface: a molecular dynamics study

Liquid crystals (LCs) are an interesting class of soft condensed matter systems characterized by an unusual combination of fluidity and long-range order, mainly known for their applications in displays (LCDs). However, the interest in LC continues to grow pushed by their application in new technologies in medicine, optical imaging, micro and nano technologies etc. In LCDs uniaxial alignment of LCs is mainly achieved by a rubbing process. During this treatment, the surfaces of polymer coated display substrates are rubbed in one direction by a rotating cylinder covered with a rubbing cloth. Basically, LC alignment involves two possible aligning directions: uniaxial planar (homogeneous) and vertical (homeotropic) to the display substrate. An interesting unresolved question concerning LCs regards the origin of their alignment on rubbed surfaces, and in particular on the polymeric ones used in the display industry. Most studies have shown that LCs on the surface of the rubbed polymer film layer are lying parallel to the rubbing direction. In these systems, micrometric grooves are generated on the film surface along the rubbing direction and also the polymer chains are stretched in this direction. Both the parallel aligned microgrooves and the polymer chains at the film surface may play a role in the LC alignment and it is not easy to quantify the effect of each contribution. The work described in this thesis is an attempt to find new microscopic evidences on the origin of LC alignment on polymeric surfaces through molecular dynamics (MD) simulations, which allow the investigation of the phenomenon with atomic detail. The importance of the arrangement of the polymeric chains in LCs alignment was studied by performing MD simulations of a thin film of a typical nematic LC, 4-cyano-4’-pentylbiphenyl (5CB), in contact with two different polymers: poly(methyl methacrylate)(PMMA) and polystyrene (PS). At least four factors are believed to influence the LC alignment: 1. the interactions of LCs with the backbone vinyl chains; 2. the interactions of LCs with the oriented side groups; 3. the anisotropic interactions of LCs with nanometric grooves; 4. the presence of static surface charges. Here we exclude the effect of microgrooves and of static surface charges from our virtual experiment, by using flat and neutral polymer surfaces, with the aim of isolating the chemical driving factors influencing the alignment of LC phases on polymeric surfaces.