Inversion and assimilation methods with applications in geophysical remote sensing

Stratospheric ozone can be measured accurately using a limb scatter remote sensing technique at the UV-visible spectral region of solar light. The advantages of this technique includes a good vertical resolution and a good daytime coverage of the measurements. In addition to ozone, UV-visible limb scatter measurements contain information about NO2, NO3, OClO, BrO and aerosols. There are currently several satellite instruments continuously scanning the atmosphere and measuring the UVvisible region of the spectrum, e.g., the Optical Spectrograph and Infrared Imager System (OSIRIS) launched on the Odin satellite in February 2001, and the Scanning Imaging Absorption SpectroMeter for Atmospheric CartograpHY (SCIAMACHY) launched on Envisat in March 2002. Envisat also carries the Global Ozone Monitoring by Occultation of Stars (GOMOS) instrument, which also measures limb-scattered sunlight under bright limb occultation conditions. These conditions occur during daytime occultation measurements. The global coverage of the satellite measurements is far better than any other ozone measurement technique, but still the measurements are sparse in the spatial domain. Measurements are also repeated relatively rarely over a certain area, and the composition of the Earth’s atmosphere changes dynamically. Assimilation methods are therefore needed in order to combine the information of the measurements with the atmospheric model. In recent years, the focus of assimilation algorithm research has turned towards filtering methods. The traditional Extended Kalman filter (EKF) method takes into account not only the uncertainty of the measurements, but also the uncertainty of the evolution model of the system. However, the computational cost of full blown EKF increases rapidly as the number of the model parameters increases. Therefore the EKF method cannot be applied directly to the stratospheric ozone assimilation problem. The work in this thesis is devoted to the development of inversion methods for satellite instruments and the development of assimilation methods used with atmospheric models.

Otimização da análise isotópica de UF6 utilizando-se a técnica de espectrometria de massas por quadrupolo

A procedure for determining of the isotope ratio 235U/238U in UF6 samples was established using a quadrupole mass spectrometer with ionization by electron impact. The following items were optimized in the spectrometer: the parameters in the ion source that provided the most intense peak, with good shape, for the most abundant isotope; the resolution that reduced the non linear effects and the number of analytical cycles that reduced the uncertainty in the results. The measurement process was characterized with respect to the effects of mass discrimination, linearity and memory effect.

Validação da metodologia da avaliação de incerteza em curvas de calibração melhor ajustadas por polinômios de segundo grau

The most widespread literature for the evaluation of uncertainty - GUM and Eurachem - does not describe explicitly how to deal with uncertainty of the concentration coming from non-linear calibration curves. This work had the objective of describing and validating a methodology, as recommended by the recent GUM Supplement approach, to evaluate the uncertainty through polynomial models of the second order. In the uncertainty determination of the concentration of benzatone (C) by chromatography, it is observed that the uncertainty of measurement between the methodology proposed and Monte Carlo Simulation, does not diverge by more than 0.0005 unit, thus validating the model proposed for one significant digit.

Validação e estimativa da incerteza de método para análise de licopeno e β-caroteno em polpa de tomate por cromatografia líquida de alta eficiência

A method to quantify lycopene and β-carotene in freeze dried tomato pulp by high performance liquid chromatography (HLPC) was validated according to the criteria of selectivity, sensitivity, precision and accuracy, and uncertainty estimation of measurement was determined with data obtained in the validation. The validated method presented is selective in terms of analysis, and it had a good precision and accuracy. Detection limit for lycopene and β-carotene was 4.2 and 0.23 mg 100 g-1, respectively. The estimation of expanded uncertainty (K = 2) for lycopene was 104 ± 21 mg 100 g-1 and for β-carotene was 6.4 ± 1.5 mg 100 g-1.

Organic and total mercury determination in sediments by cold vapor atomic absorption spectrometry: methodology validation and uncertainty measurements

The purpose of the present study was to validate a method for organic Hg determination in sediment. The procedure for organic Hg was adapted from literature, where the organomercurial compounds were extracted with dichloromethane in acid medium and subsequent destruction of organic compounds by bromine chloride. Total Hg was performed according to 3051A USEPA methodology. Mercury quantification for both methodologies was then performed by CVAAS. Methodology validation was verified by analyzing certified reference materials for total Hg and methylmercury. The uncertainties for both methodologies were calculated. The quantification limit of 3.3 µg kg-1 was found for organic Hg by CVAAS.

Measurement and Improvement of Wet Paper Web Strength

Various strength properties of paper are measured to tell how well it resists breaks in a paper machine or in printing presses. The most often measured properties are dry tensile strength and dry tear strength. However, in many situations where paper breaks, it is not dry. For example, in web breaks after the wet pressing the dry matter content can be around 45%. Thus, wet-web strength is often a more critical paper property than dry strength. Both wet and dry strength properties of the samples were measured with a L&W tensile tester. Originally this device was not designed for the measurement of the wet web tensile strength, thus a new procedure to handle the wet samples was developed. The method was tested with Pine Kraft (never dried). The effect of different strength additives on the wet-web and dry paper tensile strength was studied. The polymers used in this experiment were aqueous solution of a cationic polyamidoamine-epichlorohydrin resin (PAE), cationic hydrophilised polyisocyanate and cationic polyvinylamine (PVAm). From all three used chemicals only Cationic PAE considerably increased the wet web strength. However it was noticed that at constant solids content all chemicals decreased the wet web tensile strength. So, since all chemicals enhanced solid content it can be concluded that they work as drainage aids, not as wet web strength additives. From all chemicals only PVAm increased the dry strength and two other chemicals even decreased the strength. As chemicals were used in strong diluted forms and were injected into the pulp slurry, not on the surface of the papersheets, changes in samples densities did not happen. Also it has to be noted that all these chemicals are mainly used to improve the wet strength after the drying of the web.

Performance Measurement of the Logistics Process

The objective of the thesis was to create a performance measurement system for the logistics process of a company. In addition, one goal was to make suggestions for improvements based on description and analysis of the process and current measures. The logistics process was described in detail, and the objectives for it were derived from the company strategy and goals. Suggestions for performance measurement system and process improvement were made based on current state analysis. As a result of the thesis, three new performance measures were decided to take into use. In addition, several improvements were suggested to the ERP system to make process smoother. Some of the improvements have already been added to the system and the rest will be added in the near future.

Harmonized performance measurement system for basic industry's service centers

The objective of this study is to create measurement system that is capable to measure performance in basic industry’s service centers. First it is examined what is performance and how it can be measured. The study also introduces commonly known measurement frameworks. After theory the study investigates how companies in the field of basic industry measure their operations in practise. The investigation is done examining three case examples and by analyzing survey results from basic industry companies. On the survey results focus is on what meters and measurement systems companies use. It is also viewed what measurement problems companies have faced. In the applied part of the study harmonized performance measurement system is created. The framework of the measurement system is introduced and measurement system for the target company is created. The target company felt that the harmonized performance measurement system has good potential and continues to develop it further.

Creating a Performance Measurement System for Accounting Services of Large Paper Company

The main objective of this research is creating a performance measurement system for accounting services of a large paper industry company. In this thesis there are compared different performance measurement system and then selected two systems, which are presented and compared more detailed. Performance Prism system is the used framework in this research. Performance Prism using success maps to determining objectives. Model‟s target areas are divided into five groups: stakeholder satisfaction, stakeholder contribution, strategy, processes and capabilities. The measurement system creation began by identifying stakeholders and defining their objectives. Based on the objectives are created success map. Measures are created based on the objectives and success map. Then is defined needed data for measures. In the final measurement system, there are total just over 40 measures. Each measure is defined specific target level and ownership. Number of measures is fairly large, but this is the first version of the measurement system, so the amount is acceptable.

Mittaukset kostean höyryn turbiineille

Diplomityön tavoitteena oli selvittää Loviisan ydinvoimalaitoksen höyryturbiinin suoritus-kyvyn mittaamiseen käytettävissä olevia menetelmiä ja mittausjärjestelmiä. Tavoitteena oli selvittää mitkä tekijät aiheuttavat mittauksiin mittausvirheitä ja tutkia turbiineiden nykyisten mittalaitteiden epävarmuudet. Tässä diplomityössä selvitettiin millaisia standardinmukaisia testejä sekä muita varteenotettavia testejä turbiinin suorituskyvyn määrittämiseen on käytetty ja millaisia mittauksia ne vaativat. Lisäksi tutkittiin eri lähteistä millaisia mittalaitteita ja mittausjärjestelmiä voidaan käyttää turbiinin toiminnan mittauksiin. Soveltuvista mittausmenetelmistä esitettiin toimintaperiaatteet ja teoria. Kunnonvalvontaa varten esiteltiin värähtelyiden ja vääntö-momentin mittaamisen periaatteet. Epävarmuuksia arvioitiin mittalaitteiden teoreettisen epävarmuuden ja laitesijoittelun pohjalta. Työssä havaittiin, että suorituskyvyn arvioimiseksi on olemassa useita standardeja, mutta niiden mukaisiin mittauksiin tarvittaisiin nykyistä enemmän mittaustuloksia. Tarkkoja sekä luotettavia mittaustuloksia on haasteellista saada kaksifaasivirtauksesta. Mittalaitevalinnoilla ja mittalaitteiden määrää lisäämällä voidaan mittausten epävarmuutta pienentää. Loviisan ydinvoimalaitokselle ehdotettiin muutamia mittausjärjestelmiä turbiinin suoritus-kyvyn määrittämiseksi. Erityisesti turbiinin sisäiset olosuhteet tulisi määrittää nykyistä tarkemmin. Vääntömomentin mittaaminen olisi hyvä kunnonvalvonnan työkalu.

Sales performance measurement and steering in a multinational company

The objective of the study is to find out how sales performance should be measured and how should sales be steered in a multinational company. The beginning of the study concentrates on the literature regarding sales, performance measurement, sales performance measurement, and sales steering. The empirical part of the study is a case study, in which the information was acquired from interviews with the key personnel of the company. The results of the interviews and the revealed problems were analyzed, and comparison for possible solutions was performed. When measuring sales performance, it is important to discover the specific needs and objectives for such a system. Specific needs should be highlighted in the design of the system. The system should be versatile and the structure of the system should be in line with the organizational structure. The role of the sales performance measurement system was seen to be important in helping sales steering. However, the importance of personal management and especially conversations were seen as really critical issue in the steering. Sales performance measurement could be based on the following perspectives: financial, market, customer, people, and future. That way the sales department could react to the environmental changes more rapidly.