Palautetta Vasaralle : keskustelua

Kommentti kirja-arvosteluun: Ongelmana suhde aiempaan tutkimukseen / Erkki Vasara. // Historiallinen aikakauskirja. 105 (2007) : 1, s. 105-108

Hajautetun sähköntuotannon verkostovaikutukset

Tässä kandidaatintyössä on käsitelty hajautetun sähköntuotannon verkostovaikutuksia eri näkökulmista. Työssä on esitelty keskeisimmät sähkötekniset vaikutukset jakeluverkkoon ja tarkasteltu vaikutuksia suojauksen, käyttövarmuuden, verkkoliiketoiminnan ja suunnittelun näkökulmasta. Tarkastelu osuuden lopuksi on esitetty yksinkertainen esimerkki pienvoimalan liittämisen vaikutuksista jakeluverkkoon. Työn lopuksi on otettu katsaus tuleviin vaikutuksiin tuotantoyksiköiden lisääntyessä jakeluverkoissa. Hajautettu sähköntuotanto mahdollistaa paikallisten energiavarojen hyödyntämisen sähköntuotantoon jakeluverkon alueella. Tämä tarkoittaa, että siirtoetäisyydet pienenevät, jolloin häviöt saadaan minimoitua. Haittapuolena tällaisessa järjestelmässä on epävarmuus jakeluverkon ja tuotantoyksiköiden käyttäytymisestä eri tilanteissa, kuten myös jännitteen nousu. Suojauksen toimivuus on myös suuri ongelma, koska sen täytyy toimia riippumatta siitä onko voimala verkossa vai ei. Suojauksen toiminta hajautetun tuotannon yhteydessä on epävarmaa ja selvästi tällä hetkellä suurin este järjestelmän laajempaan hyödyntämiseen.

Determination of compression behaviour of coating layer

The strength properties of paper coating layer are very important in converting and printing operations. Too great or low strength of the coating can affect several problems in printing. One of the problems caused by the strength of coating is the cracking at the fold. After printing the paper is folded to final form and the pages are stapled together. In folding the paper coating can crack causing aesthetic damage over printed image or in the worst case the centre sheet can fall off in stapling. When folding the paper other side undergoes tensile stresses and the other side compressive stresses. If the difference between these stresses is too high, the coating can crack on the folding. To better predict and prevent cracking at the fold it is good to know the strength properties of coating layer. It has measured earlier the tensile strength of coating layer but not the compressive strength. In this study it was tried to find some way to measure the compressive strength of the coating layer and investigate how different coatings behave in compression. It was used the short span crush test, which is used to measure the in-plane compressive strength of paperboards, to measure the compressive strength of the coating layer. In this method the free span of the specimen is very small which prevent buckling. It was measured the compressive strength of free coating films as well as coated paper. It was also measured the tensile strength and the Bendtsen air permeance of the coating film. The results showed that the shape of pigment has a great effect to the strength of coating. Platy pigment gave much better strength than round or needle-like pigment. On the other hand calcined kaolin, which is also platy but the particles are aggregated, decreased the strength substantially. The difference in the strength can be explained with packing of the particles which is affecting to the porosity and thus to the strength. The platy kaolin packs up much better than others and creates less porous structure. The results also showed that the binder properties have a great effect to the compressive strength of coating layer. The amount of latex and the glass transition temperature, Tg, affect to the strength. As the amount of latex is increasing, the strength of coating is increasing also. Larger amount of latex is binding the pigment particles better together and decreasing the porosity. Compressive strength was increasing when the Tg was increasing because the hard latex gives a stiffer and less elastic film than soft latex.

Stabilization of the ionic form of weak acid cation exchange resins

Weak acid cation exchange (WAC) resins are used in the chromatographic separation of betaine from vinasse, a by-product of sugar industry. The ionic form of the resin determines the elution time of betaine. When a WAC-resin is in hydrogen form, the retention time of betaine is the longest and betaine elutes as the last component of vi-nasse from the chromatographic column. If the feed solution contains salts and its pH is not acidic enough to keep the resin undissociated, the ionic form of the hydrogen form resin starts to alter. Vinasse contains salts and its pH is around 5, it also contains weak acids. To keep the metal ion content (Na/H ratio) of the resin low enough to ensure successful separation of betaine, acid has to be added to either eluent (water) or vinasse. The aim of the present work was to examine by laboratory experiments which option requires less acid. Also the retention mechanism of betaine was investigated by measuring retention volumes of acetic acid and choline in different Na/H ratios of the resin. It was found that the resulting ionic form of the resin is the same regardless of whether the regeneration acid is added to the eluent or the feed solution (vinasse). Be-sides the salt concentration and the pH of vinasse, also the concentration of weak acids in the feed affects the resulting ionic form of the resin. The more buffering capacity vinasse has, the more acid is required to keep the ionic form of the resin desired. Vinasse was found to be quite strong buffer solution, which means relatively high amounts of acid are required to prevent the Na/H ratio from increasing too much. It is known that the retention volume of betaine decreases significantly, when the Na/H ratio increases. This is assumed to occur, because the amount of hydrogen bonds between the carboxylic groups of betaine and the resin decreases. Same behavior was not found with acetic acid. Choline has the same molecular structure as betaine, but instead of carboxylic group it has hydroxide group. The retention volume of choline increased as the Na/H ratio of the resin increased, because of the ion exchange reaction between choline cation and dissociated carboxylic group of the resin. Since the retention behavior of choline on the resin is opposite to the behavior of be-taine, the strong affinity of betaine towards hydrogen form WAC-resin has to be based on its carboxylic group. It is probable that the quaternary ammonium groups also affect the behavior of the carboxylic groups of betaine, causing them to form hydrogen bonds with the carboxylic groups of the resin.

Museologia

Museologian kokoelma koostuu n. 1700 niteestä museoalan monografioita. Kokoelma sijaitsee Sturenkadulla kirjaston pääkokoelman yhteydessä ja on lainattavissa. Kokoelma sisältää eniten 1990- ja 2000-luvulla julkaistua museoalan tutkimusta, museolaitoksen historiaa, museoiden kokoelmatyöhön ja yleisötoimintaan liittyvää kirjallisuutta, sekä yleistä kulttuuriperinnön säilyttämiseen liittyvää aineistoa. Kotimaisten kielten lisäksi (fin 28%, swe 19%) suuri osa aineistosta on englanninkielistä (eng 33%). Lisäksi kirjastoon hankitaan runsaasti kotimaisia ja ulkomaisia museoalan lehtiä, osa saadaan myös e-versioina.

Automaatiotrukkijärjestelmän soveltuvuus logistiikkakeskuksen keräystoimintoihin

Työn tavoitteena oli selvittää soveltuvatko automaatiotrukit Inexin Espoon logistiikkakeskuksen toimintaympäristöön ja voidaanko niiden avulla saavuttaa kustannussäästöjä. Työn pääpainoalueena olivat kerääminen ja siihen läheisesti liittyvät toiminnot, kuten lähetysyksiköiden siirtäminen keräyksestä lähettämöön. Logistiikkakeskuksen keräystoiminnat ovat nykyisellään hyvällä tasolla. Vuonna 2005 käyttöönotettu puheohjattu keräysjärjestelmä, on tehostanut huomattavasti toimintaa ja vähentänyt keräysvirheitä verrattuna aikaisempaan tarrakeräykseen. Logistiikkakeskuksen toimintamalli on kuitenkin hyvin työvoimaa sitova, koska pääkeräysalueilla ei ole käytössä automaatiota. Tämän johdosta osittaisetkin automatisointimahdollisuudet haluttiin selvittää. Tutkimuksen perusteella keräykseen liittyviä toimintoja olisi mahdollista osittain tehostaa automaatiotrukkijärjestelmällä. Soveltuvien keräystehtävien osuus on kuitenkin melko pieni, joten investoinnin kustannukset nousevat suureksi verrattuna saavutettavaan hyötyyn. Lähetysyksiköiden lähettämöön siirtojen automatisoinnin haasteena on tilanahtaus ja suuri manuaalitrukkiliikenne.

Outsourcing Challenges in Russia

The study focuses on the key factors in outsourcing from the viewpoint of manufacturing companies operating in Russia. The goal has been to give an overview of the different kinds of challenges companies might face in the case of outsourcing. Of particular interest are the possible risks which might originate from the subcontract relationship, as well as managing these risks. The empirical material for this qualitative interview study was collected from three large-scale manufacturing companies operating in food industry in Russia. Two of the interviewed companies were local Russian actors, and one was an international firm. According to the respondents, a big challenge is to find a suitable supplier in the Russian markets. If there are suppliers available, they may often not be capable of operating as outsourcing partners. The most common problems faced with suppliers are unstable quality and arbitrary pricing. Whether the suppliers are capable to offer activities which satisfy the company’s own and the end customers’ requirements, seems to be the biggest concern in the interviewed companies. This quality risk is managed by the strategy of multiple sourcing. Single sourcing is seen as an impossible option. The interviewed companies have no organised risk management with their external suppliers.

Biopolttoaineilla toimiva Stirling-voimalaitos

Stirling-moottori on ns. kuumailma moottori, joka toimii kaasun lämpötilaeron avulla. Kuumailma moottorin erityispiirteitä on laitteen ulkopuolella tapahtuva palaminen, josta lämpö johdetaan moottorille. Yleensä polttoaineena on käytetty vähän likaavaa polttoainetta esim. maakaasua mutta fossiilisten polttoaineiden kallistumisen ja niistä aiheutuvien päästöjen vuoksi niiden korvaaminen biopolttoaineella on tullut ajankohtaiseksi aiheeksi. Biopolttoaineiden likaavuuden takia niillä ei kuitenkaan voida lämmittää Stirling-moottoria suoraan vaan tarvitaan ylimääräinen lämmönsiirrin. Tämä diplomityö suoritettiin Lappeenrannan teknilliselle yliopistolle ja sen tarkoituksena oli tutkia juuri tähän laitteistoon suunnitellun, Stirling-moottorin ja polttokammion välisen lämmönsiirtimen suoritusarvoja ja likaantumista. Lisäksi työssä tutkittiin lämmönsiirtimeltä Stirling-moottorille menevien ilmaputkien lämpöhäviöitä. Työssä tultiin siihen tulokseen, että tämän tyyppinen lämmönsiirrin on suoritusarvoiltaan keskiverto kaasu-kaasu lämmönsiirrintä parempi ja ei likaannu erityisen nopeasti. Lämpöhäviöt olivat toisaalta merkittävämmässä asemassa kuin likaantuminen. Suurista lämpötiloista johtuva eristeiden lämmöneristyskyvyn heikkeneminen tai lämmönsiirtimen vuoto aiheutti merkittäviä lämpöhäviöitä.

Characterisation of pigment particles by scanning electron microscope and image analysis programs

Coating and filler pigments have strong influence to the properties of the paper. Filler content can be even over 30 % and pigment content in coating is about 85-95 weight percent. The physical and chemical properties of the pigments are different and the knowledge of these properties is important for optimising of optical and printing properties of the paper. The size and shape of pigment particles can be measured by different analysers which can be based on sedimentation, laser diffraction, changes in electric field etc. In this master's thesis was researched particle properties especially by scanning electron microscope (SEM) and image analysis programs. Research included nine pigments with different particle size and shape. Pigments were analysed by two image analysis programs (INCA Feature and Poikki), Coulter LS230 (laser diffraction) and SediGraph 5100 (sedimentation). The results were compared to perceive the effect of particle shape to the performance of the analysers. Only image analysis programs gave parameters of the particle shape. One part of research was also the sample preparation for SEM. Individual particles should be separated and distinct in ideal sample. Analysing methods gave different results but results from image analysis programs corresponded even to sedimentation or to laser diffraction depending on the particle shape. Detailed analysis of the particle shape required high magnification in SEM, but measured parameters described very well the shape of the particles. Large particles (ecd~1 µm) could be used also in 3D-modelling which enabled the measurement of the thickness of the particles. Scanning electron microscope and image analysis programs were effective and multifunctional tools for particle analyses. Development and experience will devise the usability of analysing method in routine use.

Quantitative market and sales forecast accuracy analysis

The main objective of this master’s thesis was to quantitatively study the reliability of market and sales forecasts of a certain company by measuring bias, precision and accuracy of these forecasts by comparing forecasts against actual values. Secondly, the differences of bias, precision and accuracy between markets were explained by various macroeconomic variables and market characteristics. Accuracy and precision of the forecasts seems to vary significantly depending on the market that is being forecasted, the variable that is being forecasted, the estimation period, the length of the estimated period, the forecast horizon and the granularity of the data. High inflation, low income level and high year-on-year market volatility seems to be related with higher annual market forecast uncertainty and high year-on-year sales volatility with higher sales forecast uncertainty. When quarterly market size is forecasted, correlation between macroeconomic variables and forecast errors reduces. Uncertainty of the sales forecasts cannot be explained with macroeconomic variables. Longer forecasts are more uncertain, shorter estimated period leads to higher uncertainty, and usually more recent market forecasts are less uncertain. Sales forecasts seem to be more uncertain than market forecasts, because they incorporate both market size and market share risks. When lead time is more than one year, forecast risk seems to grow as a function of root forecast horizon. When lead time is less than year, sequential error terms are typically correlated, and therefore forecast errors are trending or mean-reverting. The bias of forecasts seems to change in cycles, and therefore the future forecasts cannot be systematically adjusted with it. The MASE cannot be used to measure whether the forecast can anticipate year-on-year volatility. Instead, we constructed a new relative accuracy measure to cope with this particular situation.