Extractants to assess zinc phytoavailability in mineral fertilizer and industrial by-products

Efficient analytical methods for the quantification of plant-available Zn contained in mineral fertilizers and industrial by-products are fundamental for the control and marketing of these inputs. In this sense, there are some doubts on the part of the scientific community as well as of the fertilizer production sector, whether the extractor requested by the government (Normative Instruction No. 28, called 2nd extractor), which is citric acid 2 % (2 % CA) (Brasil, 2007b), is effective in predicting the plant availability of Zn via mineral fertilizers and about the agronomic significance of the required minimal solubility of 60 % compared to the total content (HCl) (Brasil, 2007a). The purpose of this study was to evaluate the alternative extractors DTPA, EDTA, neutral ammonium citrate (NAC), buffer solution pH 6.0, 10 % HCl, 10 % sulfuric acid, 1 % acetic acid, water, and hot water to quantify the contents of Zn available for maize and compare them with indices of agronomic efficiency of fertilizers and industrial by-products when applied to dystrophic Clayey Red Latosol and Dystrophic Alic Red Yellow Latosol with medium texture. The rate of Zn applied to the soil was 5 mg kg-1, using the sources zinc sulfate, commercial granular zinc, ash and galvanic sludge, ash and two brass slags. Most Zn was extracted from the sources by DTPA, 10 % HCl, NAC, 1% acetic acid, and 10 % sulfuric acid. Recovery by the extractors 2 % CA, EDTA, water, and hot water was low. The agronomic efficiency index was found to be high when using galvanic sludge (238 %) and commercial granular zinc (142 %) and lower with brass slag I and II (67 and 27 %, respectively). The sources galvanizing ash and brass ash showed solubility lower than 60 % in 2 % CA, despite agronomic efficiency indices of 78 and 125 %, respectively. The low agronomic efficiency index of industrial by-products such as brass slag I and galvanizing ash can be compensated by higher doses, provided there is no restriction, as well as for all other sources, in terms of contaminant levels of arsenic, cadmium, chromium, lead, and mercury as required by law (Normative Instruction No 27/2006). The implementation of 2nd extractor 2 % CA and the requirement of minimum solubility for industrial by-products could restrict the use of alternative sources as potential Zn sources for plants.

PHYTOAVAILABILITY OF COPPER IN INDUSTRIAL BY-PRODUCTS AND MINERAL FERTILIZERS

Alternative copper (Cu) sources could be used in fertilizer production, although the bioavailability of copper in these materials is unknown. The objective of this study was to evaluate the extractants neutral ammonium citrate (NAC), 2 % citric acid, 1 % acetic acid, 10 % HCl, 10 % H2SO4, buffer solution pH 6.0, DTPA, EDTA, water, and hot water in the quantification of available Cu content in several sources, relating them to the relative agronomic efficiency (RAE) of wheat grown in a clayey Latossolo Vermelho eutrófico (Oxisol) and Neossolo Quartzarênico (Typic Quartzipsamment). Copper was applied at the rate of 1.5 mg kg-1 as scrap slag, brass slag, Cu ore, granulated copper, and copper sulfate. The extractants 10 % HCl, 10 % H2SO4, and NAC extracted higher Cu concentrations. The RAE values of brass slag and Cu ore were similar to or higher than those of Cu sulfate and granulated Cu. Solubility in the 2nd NAC extractant, officially required for mineral fertilizers with Cu, was lower than 60 % for the scrap slag, Cu ore, and granulated copper sources. This fact indicates that adoption of the NAC extractant may be ineffective for industrial by-products, although no extractant was more efficient in predicting Cu availability for wheat fertilized with the Cu sources tested.

Learning in Product Development Projects - Responding to challenges in global industrial company

Verkostoitunut kansainvälinen tuotekehitys on tärkeä osa menestystä nykypäivän muuttuvassa yritysmaailmassa. Toimintojen tehostamiseksi myös projektitoiminnot on sopeutettava kansainväliseen toimintaympäristöön. Kilpailukyvyn säilyttämiseksi projektitoimintoja on lisäksi jatkuvasti tehostettava. Yhtenäkeinona nähdään projektioppiminen, jota voidaan edistää monin eri tavoin. Tässätyössä keskitytään projektitiedonhallinnan kehittämisen tuomiin oppimismahdollisuuksiin. Kirjallisuudessa kerrotaan, että projektitiedon jakaminen ja sen hyödyntäminen seuraavissa projekteissa on eräs projektioppimisen edellytyksistä. Tämäon otettu keskeiseksi näkökulmaksi tässä tutkimuksessa. Lisäksi tutkimusalueen rajaamiseksi työ tarkastelee erityisesti projektioppimista kansainvälisten tuotekehitysprojektien välillä. Työn tavoitteena on esitellä keskeisiä projektioppimisen haasteita ja etsiä konkreettinen ratkaisu vastaamaan näihin haasteisiin. Tuotekehitystoiminnot ja kansainvälinen hajautettu projektiorganisaatio kohtaavat lisäksi erityisiä haasteita, kuten tiedon hajautuneisuus, projektihenkilöstön vaihtuvuus, tiedon luottamuksellisuus ja maantieteelliset haasteet (esim. aikavyöhykkeet ja toimipisteen sijainti). Nämä erityishaasteet on otettu huomioon ratkaisua etsittäessä. Haasteisiin päädyttiin vastaamaan tietotekniikkapohjaisella ratkaisulla, joka suunniteltiin erityisesti huomioiden esimerkkiorganisaation tarpeet ja haasteet. Työssä tarkastellaan suunnitellun ratkaisun vaikutusta projektioppimiseen ja kuinka se vastaa havaittuihin haasteisiin. Tuloksissa huomattiin, että projektioppimista tapahtui, vaikka oppimista oli vaikea suoranaisesti huomata tutkimusorganisaation jäsenten keskuudessa. Projektioppimista voidaan kuitenkin sanoa tapahtuvan, jos projektitieto on helposti koko projektiryhmän saatavilla ja se on hyvin järjesteltyä. Muun muassa nämä ehdot täyttyivät. Projektioppiminen nähdään yleisesti haastavana kehitysalueena esimerkkiorganisaatiossa. Suuri osa tietämyksestä on niin sanottua hiljaistatietoa, jota on hankala tai mahdoton saattaa kirjalliseen muotoon. Näin olleen tiedon siirtäminen jää suurelta osin henkilökohtaisen vuorovaikutuksen varaan. Siitä huolimatta projektioppimista on mahdollista kehittää erilaisin toimintamallein ja menetelmin. Kehitys vaatii kuitenkin resursseja, pitkäjänteisyyttä ja aikaa. Monet muutokset voivat vaatia myös organisaatiokulttuurin muutoksen ja vaikuttamista organisaation jäseniin. Motivaatio, positiiviset mielikuvat ja selkeät strategiset tavoitteet luovat vakaan pohjan projektioppimisen kehittämiselle.

Comprehensive Study of Crystal Growth from Solution

Crystal growth is an essential phase in crystallization kinetics. The rate of crystal growth provides significant information for the design and control of crystallization processes; nevertheless, obtaining accurate growth rate data is still challenging due to a number of factors that prevail in crystal growth. In industrial crystallization, crystals are generally grown from multi-componentand multi-particle solutions under complicated hydrodynamic conditions; thus, it is crucial to increase the general understanding of the growth kinetics in these systems. The aim of this work is to develop a model of the crystal growth rate from solution. An extensive literature review of crystal growth focuses on themodelling of growth kinetics and thermodynamics, and new measuring techniques that have been introduced in the field of crystallization. The growth of a singlecrystal is investigated in binary and ternary systems. The binary system consists of potassium dihydrogen phosphate (KDP, crystallizing solute) and water (solvent), and the ternary system includes KDP, water and an organic admixture. The studied admixtures, urea, ethanol and 1-propanol, are employed at relatively highconcentrations (of up to 5.0 molal). The influence of the admixtures on the solution thermodynamics is studied using the Pitzer activity coefficient model. Theprediction method of the ternary solubility in the studied systems is introduced and verified. The growth rate of the KDP (101) face in the studied systems aremeasured in the growth cell as a function of supersaturation, the admixture concentration, the solution velocity over a crystal and temperature. In addition, the surface morphology of the KDP (101) face is studied using ex situ atomic force microscopy (AFM). The crystal growth rate in the ternary systems is modelled on the basis of the two-step growth model that contains the Maxwell-Stefan (MS) equations and a surface-reaction model. This model is used together with measuredcrystal growth rate data to develop a new method for the evaluation of the model parameters. The validation of the model is justified with experiments. The crystal growth rate in an imperfectly mixed suspension crystallizer is investigatedusing computational fluid dynamics (CFD). A solid-liquid suspension flow that includes multi-sized particles is described by the multi-fluid model as well as by a standard k-epsilon turbulence model and an interface momentum transfer model. The local crystal growth rate is determined from calculated flow information in a diffusion-controlled crystal growth regime. The calculated results are evaluated experimentally.

On reduced games and the lexmax solution

For a family of reduced games satisfying a monotonicity property, we introduced the reduced equal split-off set, an extension of the equal split-off set (Branzei et. al, 2006), and study its relation with the core. Regardless of the reduction operation we consider, the intersection between both sets is either empty or a singleton containing the lexmax solution (Arin et al., 2008). We also provide a procedure for computing the lexmax solution for a class of games that includes games with large core (Sharkey, 1982). [JEL Classification: C71]

Railway Wagon Market Analysis and New Multi-Purpose Wagon Solution for Freight Transports - Finnish Manufacturing Perspective

Rautateillä käytettävät tavaravaunut ovat vanhenemassa hyvin nopeasti; tämä koskee niin Venäjää, Suomea, Ruotsia kuin laajemminkin Eurooppaa. Venäjällä ja Euroopassa on käytössä runsaasti vaunuja, jotka ovat jo ylittäneet niille suositeltavan käyttöiän. Silti niitä käytetään kuljetuksissa, kun näitä korvaavia uusia vaunuja ei ole tarpeeksi saatavilla. Uusimmat vaunut ovat yleensä vaunuja vuokraavien yritysten tai uusien rautatieoperaattorien hankkimia - tämä koskee erityisesti Venäjää, jossa vaunuvuokraus on noussut erittäin suosituksi vaihtoehdoksi. Ennusteissa kerrotaan vaunupulan kasvavan ainakin vuoteen 2010 saakka. Jos rautateiden suosio rahtikuljetusmuotona kasvaa, niin voimistuva vaunukysyntä jatkuu huomattavan paljon pidemmän aikaa. Euroopan ja Venäjän vaunukannan tilanne näkyy myös sitä palvelevan konepajateollisuuden ongelmina - yleisesti ottaen alan eurooppalaiset yritykset ovat heikosti kannattavia ja niiden liikevaihto ei juuri kasva, venäläiset ja ukrainalaiset yritykset ovat olleet samassa tilanteessa, joskin aivan viime vuosina tilanne on osassa kääntynyt paremmaksi. Kun näiden maanosien yritysten liikevaihtoa, voittoa ja omistaja-arvoa verrataan yhdysvaltalaisiin kilpailijoihin, huomataan että jälkimmäisten suoriutuminen on huomattavan paljon parempaa, ja näillä yrityksillä on myös kyky maksaa osinkoja omistajilleen. Tutkimuksen tarkoituksena oli kehittää uuden tyyppinen kuljetusvaunu Suomen, Venäjän sekä mahdollisesti myös Kiinan väliseen liikenteeseen. Vaunutyypin tarkoituksena olisi kyetä toimimaan monikäyttöisenä, niin raaka-aineiden kuin konttienkin kuljetuksessa, tasapainottaen kuljetusmuotojen aiheuttamaa kuljetuspaino-ongelmaa. Kehitystyön pohjana käytimme yli 1000 venäläisen vaunutyypin tietokantaa, josta valitsimme Data Envelopment Analysis -menetelmällä soveliaimmat vaunut kontinkuljetukseen (lähemmin tarkastelimme n. 40 vaunutyyppiä), jättäen mahdollisimman vähän tyhjää tilaa junaan, mutta silti kyeten kantamaan valitun konttilastin. Kun kantokykyongelmia venäläisissä vaunuissa ei useinkaan ole, on vertailu tehtävissä tavarajunan pituuden ja kokonaispainon perusteella. Simuloituamme yhdistettyihin kuljetuksiin soveliasta vaunutyyppiä käytännössä löytyvässä kuljetusverkostossa (esim. raakapuuta Suomeen tai Kiinaan ja kontteja takaisin Venäjän suuntaan), huomasimme lyhemmän vaunupituuden sisältävän kustannusetua, erityisesti raakaainekuljetuksissa, mutta myös rajanylityspaikkojen mahdollisesti vähentyessä. Lyhempi vaunutyyppi on myös joustavampi erilaisten konttipituuksien suhteen (40 jalan kontin käyttö on yleistynyt viime vuosina). Työn lopuksi ehdotamme uuden vaunutyypin tuotantotavaksi verkostomaista lähestymistapaa, jossa osa vaunusta tehtäisiin Suomessa ja osa Venäjällä ja/tai Ukrainassa. Vaunutyypin tulisi olla rekisteröity Venäjälle, sillä silloin sitä voi käyttää Suomen ja Venäjän, kuten myös soveltuvin osin Venäjän ja Kiinan välisessä liikenteessä.

Clean development mechanism and joint implementation in China and Russia as related to industrial energy projects

Being highly discussed the problem of climate change and global warming has been keeping importance for several of decades. As a response to the world’s need in solution for climate change disasters, the United Nations Framework Convention on Climate Change was adopted in 1992 and supplemented with the Kyoto protocol in 1997. This work is aimed to give better understanding of the Convention, Kyoto Protocol with its mechanisms and their function, related to energy projects in such case countries, as Russia and China, in order to assist evaluation of projects cost-effectiveness. It provides basic information about the Convention and the Protocol with their regulations, overview of present situation and future post-Kyoto forecasts, while the most attention is concentrated on the clean development mechanism and joint implementation step-by-step project cycles and specific regulations in given countries. The current study disclosed that CDM and JI project cycles are resulting in a complicated process. By the moment it requires step-by-step following of a number of methodologies, spending time and finance to particular project development. Uncertainties about post-Kyoto period bring additional risk to the projects and complicate any business decision concerning Kyoto Protocol.

Developing a new service business model for an industrial supplier

Project business companies are moving towards solution offering in order to avoid discontinuity of project business and to gain other advantages. An option to implement solution business could be BOOT (Build-Own-Operate-Transfer) business model where a company is given the responsibilities to design, finance, build, own, operate and maintain for example production facilities of a client. The contract is made for 10-30 years, the client pays the solution during this period of time and after contract termination the facilities are transferred to the ownership of the client. The purpose of this study was to provide knowledge about BOOT business model for the company in question and its employees and to create a settlement of the advantages, disadvantages and risks of it. Furthermore, one of the main objectives was to create a description of the network needed to run a BOOT project. The objectives were met through a literature study and an explorative case study with appropriate interviews. Based on this study, the company should be able to evaluate the applicability of BOOT business model to their business environment better.

Technological solution for the automatic replacement of the catalytic filaments in HWCVD

The degradation of the catalytic filaments is the main factor limiting the industrial implementation of the hot wire chemical vapor deposition (HWCVD) technique. Up to now, no solution has been found to protect the catalytic filaments used in HWCVD without compromising their catalytic activity. Probably, the definitive solution relies on the automatic replacement of the catalytic filaments. In this work, the results of the validation tests of a new apparatus for the automatic replacement of the catalytic filaments are reported. The functionalities of the different parts have been validated using a 0.2 mm diameter tungsten filament under uc-Si:H deposition conditions.

Environmental policy instruments concerning industrial end-use energy efficiency

Energy efficiency and saving energy are the main question marks when thinking of reducing carbon dioxide emissions or cutting costs. The objective of thesis is to evaluate policy instruments concerning end-use energy efficiency of heavy industry in European Union. These policy instruments may be divided in various ways, but in this thesis the division is to administrative, financial, informative and voluntary instruments. Administrative instruments introduced in this thesis are Directive on Integrated Pollution Prevention and Control, Directive on Energy End-use Efficiency and Energy Services, and Climate and Energy Package. Financial means include energy and emission taxation, EU Emission Trading Scheme and diverse support systems. Informative instruments consist of horizontal BAT Reference Document for Energy Efficiency, as well as substantial EU documents including Green Paper on Energy Efficiency, Action Plan for Energy Efficiency and An Energy Policy for Europe. And finally, voluntary instruments include environmental managements systems like ISO 14001 and EMAS, energy auditing and benchmarking. The efficiency of different policy instruments vary quite a lot. Informative instruments lack the commitment from industry and are thus almost ineffective, contrary to EU Emission Trading Scheme, which is said to be the solution to climate problems. The efficiency of administrative means can be placed between those mentioned and voluntary instruments are still quite fresh to be examined fruitfully. However, each instrument has their potential and challenges. Cases from corporate world strengthen the results from theoretical part. Cases were written mainly on the basis of interviews. The interviewees praised the energy efficiency contract of Finnish industry, but the EU ETS takes the leading role of policy instruments. However, for industry the reductions do not come easily.

Treatment of oily wastewater by ultrafiltration: The effect of different operating and solution conditions

In many industries, such as petroleum production, and the petrochemical, metal, food and cosmetics industries, wastewaters containing an emulsion of oil in water are often produced. The emulsions consist of water (up to 90%), oils (mineral, animal, vegetable and synthetic), surfactants and other contaminates. In view of its toxic nature and its deleterious effects on the surrounding environment (soil, water) such wastewater needs to be treated before release into natural water ways. Membrane-based processes have successfully been applied in industrial applications and are considered as possible candidates for the treatment of oily wastewaters. Easy operation, lower cost, and in some cases, the ability to reduce contaminants below existing pollution limits are the main advantages of these systems. The main drawback of membranes is flux decline due tofouling and concentration polarisation. The complexity of oil-containing systems demands complementary studies on issues related to the mitigation of fouling and concentration polarisation in membranebased ultrafiltration. In this thesis the effect of different operating conditions (factors) on ultrafiltration of oily water is studied. Important factors are normally correlated and, therefore, their effect should be studied simultaneously. This work uses a novel approach to study different operating conditions, like pressure, flow velocity, and temperature, and solution properties, like oil concentration (cutting oil, diesel, kerosene), pH, and salt concentration (CaCl2 and NaCl)) in the ultrafiltration of oily water, simultaneously and in a systematic way using an experimental design approach. A hypothesis is developed to describe the interaction between the oil drops, salt and the membrane surface. The optimum conditions for ultrafiltration and the contribution of each factor in the ultrafiltration of oily water are evaluated. It is found that the effect on permeate flux of the various factors studied strongly depended on the type of oil, the type of membrane and the amount of salts. The thesis demonstrates that a system containing oil is very complex, and that fouling and flux decline can be observed even at very low pressures. This means that only the weak form of the critical flux exists for such systems. The cleaning of the fouled membranes and the influence of different parameters (flow velocity, temperature, time, pressure, and chemical concentration (SDS, NaOH)) were evaluated in this study. It was observed that fouling, and consequently cleaning, behaved differently for the studied membranes. Of the membranes studied, the membrane with the lowest propensity for fouling and the most easily cleaned was the regenerated cellulose membrane (C100H). In order to get more information about the interaction between the membrane and the components of the emulsion, a streaming potential study was performed on the membrane. The experiments were carried out at different pH and oil concentration. It was seen that oily water changed the surface charge of the membrane significantly. The surface charge and the streaming potential during different stages of filtration were measured and analysed being a new method for fouling of oil in this thesis. The surface charge varied in different stages of filtration. It was found that the surface charge of a cleaned membrane was not the same as initially; however, the permeability was equal to that of a virgin membrane. The effect of filtration mode was studied by performing the filtration in both cross-flow and deadend mode. The effect of salt on performance was considered in both studies. It was found that salt decreased the permeate flux even at low concentration. To test the effect of hydrophilicity change, the commercial membranes used in this thesis were modified by grafting (PNIPAAm) on their surfaces. A new technique (corona treatment) was used for this modification. The effect of modification on permeate flux and retention was evaluated. The modified membranes changed their pore size around 33oC resulting in different retention and permeability. The obtained results in this thesis can be applied to optimise the operation of a membrane plant under normal or shock conditions or to modify the process such that it becomes more efficient or effective.

Data Consistency by a Metadata Management Solution

This thesis consists of three main theoretical themes: quality of data, success of information systems, and metadata in data warehousing. Loosely defined, metadata is descriptive data about data, and, in this thesis, master data means reference data about customers, products etc. The objective of the thesis is to contribute to an implementation of a metadata management solution for an industrial enterprise. The metadata system incorporates a repository, integration, delivery and access tools, as well as semantic rules and procedures for master data maintenance. It targets to improve maintenance processes and quality of hierarchical master data in the case company’s informational systems. That should bring benefits to whole organization in improved information quality, especially in cross-system data consistency, and in more efficient and effective data management processes. As the result of this thesis, the requirements for the metadata management solution in case were compiled, and the success of the new information system and the implementation project was evaluated.

Sorption kinetics and intrapaticulate diffusivity of As(III) bioremediation from aqueous solution, using modified and unmodified coconut fiber

The pollution and toxicity problems posed by arsenic in the environment have long been established. Hence, the removal and recovery remedies have been sought, bearing in mind the efficiency, cost effectiveness and environmental friendliness of the methods employed. The sorption kinetics and intraparticulate diffusivity of As (III) bioremediation from aqueous solution using modified and unmodified coconut fiber was investigated. The amount adsorbed increased as time increased, reaching equilibrium at about 60 minutes. The kinetic studies showed that the sorption rates could be described by both pseudo-first order and pseudo-second order process with the later showing a better fit with a value of rate constant of 1.16 x 10-4 min-1 for the three adsorbent types. The mechanism of sorption was found to be particle diffusion controlled. The diffusion and boundary layer effects were also investigation. Therefore, the results show that coconut fiber, both modified and unmodified is an efficient sorbent for the removal of As (III) from industrial effluents with particle diffusion as the predominant mechanism.

Integration in project business : mechanisms for integrating customers and the project network during the life-cycle of industrial projects

This thesis focuses on integration in project business, i.e. how projectbased companies organize their product and process structures when they deliver industrial solutions to their customers. The customers that invest in these solutions run their businesses in different geographical, political and economical environments, which should be acknowledged by the supplier when providing solutions comprising of larger and more complex scopes than previously supplied to these customers. This means that the suppliers are increasing their supply range by taking over some of the activities in the value chain that have traditionally been handled by the customer. In order to be able to provide the functioning solutions, including more engineering hours, technical equipment and a wider project network, a change is needed in the mindset in order to be able to carry out and take the required responsibility that these new approaches bring. For the supplier it is important to be able to integrate technical products, systems and services, but the supplier also needs to have the capabilities to integrate the cross-functional organizations and departments in the project network, the knowledge and information between and within these organizations and departments, along with inputs from the customer into the product and process structures during the lifecycle of the project under development. Hence, the main objective of this thesis is to explore the challenges of integration that industrial projects meet, and based on that, to suggest a concept of how to manage integration in project business by making use of integration mechanisms. Integration is considered the essential process for accomplishing an industrial project, whereas the accomplishment of the industrial project is considered to be the result of the integration. The thesis consists of an extended summary and four papers, that are based on three studies in which integration mechanisms for value creation in industrial project networks and the management of integration in project business have been explored. The research is based on an inductive approach where in particular the design, commissioning and operations functions of industrial projects have been studied, addressing entire project life-cycles. The studies have been conducted in the shipbuilding and power generation industries where the scopes of supply consist of stand-alone equipment, equipment and engineering, and turnkey solutions. These industrial solutions include demanding efforts in engineering and organization. Addressing the calls for more studies on the evolving value chains of integrated solutions, mechanisms for inter- and intra-organizational integration and subsequent value creation in project networks have been explored. The research results in thirteen integration mechanisms and a typology for integration is proposed. Managing integration consists of integrating the project network (the supplier and the sub-suppliers) and the customer (the customer’s business purpose, operations environment and the end-user) into the project by making use of integration mechanisms. The findings bring new insight into research on industrial project business by proposing integration of technology and engineering related elements with elements related to customer oriented business performance in contemporary project environments. Thirteen mechanisms for combining products and the processes needed to deliver projects are described and categorized according to the impact that they have on the management of knowledge and information. These mechanisms directly relate to the performance of the supplier, and consequently to the functioning of the solution that the project provides. This thesis offers ways to promote integration of knowledge and information during the lifecycle of industrial projects, enhancing the development towards innovative solutions in project business.

Electrocoagulation in the treatment of industrial waters and wastewaters

Chemical coagulation is commonly used in raw water and wastewater treatment plants for the destabilisation of pollutants so that they can be removed in the subsequent separation processes. The most commonly used coagulation chemicals are aluminium and iron metal salts. Electrocoagulation technology has also been proposed for the treatment of raw waters and wastewaters. With this technology, metal cations are produced on the electrodes via electrolysis and these cations form various hydroxides in the water depending on the water pH. In addition to this main reaction, several side reactions, such as hydrogen bubble formation and the reduction of metals on cathodes, also take place in the cell. In this research, the applications of electrocoagulation were investigated in raw water treatment and wastewater applications. The surface water used in this research contained high concentrations of natural organic matter (NOM). The effect of the main parameters – current density, initial pH, electric charge per volume, temperature and electrolysis cell construction – on NOM removal were investigated. In the wastewater treatment studies, the removal of malodorous sulphides and toxic compounds from the wastewaters and debarking effluents were studied. Also, the main parameters of the treatment, such as initial pH and current density, were investigated. Aluminium electrodes were selected for the raw water treatment, whereas wastewaters and debarking effluent were treated with iron electrodes. According to results of this study, aluminium is more suitable electrode material for electrocoagulation applications because it produces Al(III) species. Metal ions and hydroxides produced by iron electrodes are less effective in the destabilisation of pollutants because iron electrodes produce more soluble and less charged Fe(II) species. However, Fe(II) can be effective in some special applications, such as sulphide removal. The resulting metal concentration is the main parameter affecting destabilisation of pollutants. Current density, treatment time, temperature and electrolysis cell construction affect the dissolution of electrodes and hence also the removal of pollutants. However, it seems that these parameters have minimal significance in the destabilization of the pollutants besides this effect (in the studied range of parameters). Initial pH and final pH have an effect on the dissolution of electrodes, but they also define what aluminium or iron species are formed in the solution and have an effect on the ζ-potential of all charged species in the solution. According to the results of this study, destabilisation mechanisms of pollutants by electrocoagulation and chemical coagulation are similar. Optimum DOC removal and low residual aluminium can be obtained simultaneously with electrocoagulation, which may be a significant benefit of electrocoagulation in surface water treatment compared to chemical coagulation. Surface water treatment with electrocoagulation can produce high quality water, which could be used as potable water or fresh water for industrial applications. In wastewater treatment applications, electrocoagulation can be used to precipitate malodorous sulphides to prevent their release into air. Technology seems to be able to remove some toxic pollutants from wastewater and could be used as pretreatment prior to treatment at a biological wastewater treatment plant. However, a thorough economic and ecological comparison of chemical coagulation and electrocoagulation is recommended, because these methods seem to be similar in pollutant destabilisation mechanisms, metal consumption and removal efficiency in most applications.