Utilization of a Time Domain Simulator in the Technical and Economic Analysis of a Wind Turbine Electric Drive Train

The amount of installed wind power has been growing exponentially during the past ten years. As wind turbines have become a significant source of electrical energy, the interactions between the turbines and the electric power network need to be studied more thoroughly than before. Especially, the behavior of the turbines in fault situations is of prime importance; simply disconnecting all wind turbines from the network during a voltage drop is no longer acceptable, since this would contribute to a total network collapse. These requirements have been a contributor to the increased role of simulations in the study and design of the electric drive train of a wind turbine. When planning a wind power investment, the selection of the site and the turbine are crucial for the economic feasibility of the installation. Economic feasibility, on the other hand, is the factor that determines whether or not investment in wind power will continue, contributing to green electricity production and reduction of emissions. In the selection of the installation site and the turbine (siting and site matching), the properties of the electric drive train of the planned turbine have so far been generally not been taken into account. Additionally, although the loss minimization of some of the individual components of the drive train has been studied, the drive train as a whole has received less attention. Furthermore, as a wind turbine will typically operate at a power level lower than the nominal most of the time, efficiency analysis in the nominal operating point is not sufficient. This doctoral dissertation attempts to combine the two aforementioned areas of interest by studying the applicability of time domain simulations in the analysis of the economicfeasibility of a wind turbine. The utilization of a general-purpose time domain simulator, otherwise applied to the study of network interactions and control systems, in the economic analysis of the wind energy conversion system is studied. The main benefits of the simulation-based method over traditional methods based on analytic calculation of losses include the ability to reuse and recombine existing models, the ability to analyze interactions between the components and subsystems in the electric drive train (something which is impossible when considering different subsystems as independent blocks, as is commonly done in theanalytical calculation of efficiencies), the ability to analyze in a rather straightforward manner the effect of selections other than physical components, for example control algorithms, and the ability to verify assumptions of the effects of a particular design change on the efficiency of the whole system. Based on the work, it can be concluded that differences between two configurations can be seen in the economic performance with only minor modifications to the simulation models used in the network interaction and control method study. This eliminates the need ofdeveloping analytic expressions for losses and enables the study of the system as a whole instead of modeling it as series connection of independent blocks with no lossinterdependencies. Three example cases (site matching, component selection, control principle selection) are provided to illustrate the usage of the approach and analyze its performance.

Utilization of Incident Reporting in The Finnish Maritime Industry

Marine traffic is expected to increase rapidly in the future, both in the Baltic Sea and in the Gulf of Finland. As the number of vessels in the area increases, so does the risk of serious marine accidents. To help prevent such accidents in the future, the International Maritime Organization (IMO) has put forth the International Safety Management Code (the ISM Code), which aims to improve the safety of the vessels. The second work package of the Development of maritime safety culture (METKU) project investigates the effects of the ISM Code and potential areas of improvement in maritime safety. The first phase in the work package used a literature review to determine how maritime safety culture could be improved. Continuous improvement, management commitment and personnel empowerment and motivation were found to be essential. In the second phase, shipping companies and administrators were interviewed. It was discovered that especially incident reporting based on continuous improvement was felt to be lacking. This third phase aims to take a closer look at incident reporting and suggest improvements based on the findings. Both the IMO and national legislation encourage shipping companies in incident reporting, and on the national level a shared incident reporting system (ForeSea) is being pushed forward. The objective of this research project was to find out the IMO’s attitude towards incident reporting, to establish a theoretical framework of reference in incident reporting, and to observe how reporting is actually being employed on the seas. Existing incident reporting systems were also researched. The study was carried out using a literature review and the results previously gathered in interviews. The results of phase two were elaborated further for themes relating to incident reporting. According to the findings of this research, the theoretical background of incident reporting dates back to the early 20th century. Although some theories are widely accepted, some have also received criticism. The lack of a concise, shared terminology poses major difficulties in maritime incident reporting and in determining its efficiency. A central finding is the fact that existing incident reporting focuses mostly on information flow away from the ship, whereas the backward information flow is much less planned and monitored. In incident reporting, both nationally and internationally, stakeholders are plenty. The information produced by these parties is scattered, however, and thus not very usable. Based on this research, the centralizing of this information should be made a priority. Traditionally, the success of incident reporting has been determined statistically, from the number of reported incidents. Yet existing reporting systems have not been designed with such statistical analysis in mind, so different methodologies might yield a more comprehensive view. The previous findings of seafarers and management (including shipping companies and administration) having differing views on safety work and safety management were backed up by the results of this study. Seafarers find seamanship and storytelling important, while management wants a more systematic and broad approach on safety matters. The research project was carried out by the Centre for Maritime Studies of the University of Turku, in the Kotka unit (Maritime Logistics Research), with coordination by the Kotka Maritime Research Centre. The major financiers of the project were the European Union and the city of Kotka. The financing authority was the Regional Council of Päijät-Häme. Partners in the project were the shipping companies Finnlines Oyj, Kristina Cruises Oy, Meriaura Oy and VG-Shipping Oy, and the ports of Helsinki, Kotka and Hamina. The partners provided both funding for the project and information for the research.

Success of service-intensive manufacturing firms - resource-based view

The main objective of this study is to examine the relationships between resources, competitive advantage and firm success. The study focuses, on one hand, on the financial performance of service-intensive manufac-turing firms against competitors with a lower service intensity and, on the other hand, on the resources as drivers for competitive advantage and success. The purpose of the theoretical part is to link the study in the field of the strategy research. The empirical part of the study is based on the quantitative analyses of the survey data collected from 50 major suppliers of industrial machinery and transportation equipment in Europe and North America. Results indicate that service-intensive manufacturing firms have performed better and their performance has been more stable vis-à-vis their peers. The main resources that differentiate service-intensive manufacturing firms from their non-service intensive competitors are service strategy and service-oriented top management. The analyses on the VRIO resources produced only a limited amount of information and solely service-centred culture appeared to be a rent generating resource.

Utilization of Automatic Meter Reading in the Improvement of a District Heating System

A district heating system comprises production facilities, a distribution network, and heat consumers. The utilization of new energy metering and reading system (AMR) is increasing constantly in district heating systems. This heuristic study shows how the AMR system can be exploited in finding optimization opportunities in district heating system. In this study, the district heating system is mainly considered from the viewpoint of operational optimization. The focus is on the core processes, heat production and distribution. Three objectives were set to this study. The first one was to examine general optimization opportunities in district heating systems. Second, to figure out the benefits of AMR for general optimization opportunities. Finally, to define a methodology for process improvement endeavors. This study shows, through a case study, the usefulness of AMR in specifying current deficiencies in a district heating system. Based on a literature review, the methodology for the improvement of business processes is presented. Additionally, some issues related to future competitiveness of district heating are concerned. As a conclusion, some optimization objectives are considered more desirable than others. Study shows that AMR is useful in the specification of optimization targets in the district heating system. Further steps in optimization process were not examined in detail. That would seem to be interesting topic for further studies.

Utilization of Meat and bone meal for energy production

At the end of the 1990s the stock breeding in the Europe was suffering from the animal disease epidemics such as Bovine spongiform encephalopathy (BSE) and foot –and mouth disease. The European Union (EU) tackled to this problem by tightening the legislation of animal by-products. At this point, rendering and fat producing industries faces new challenges, which they have to cope with in a way of trying to find alternatives to their products (animal fats and meat and bone meal). One of the most promising alternatives to utilize these products was to use them in energy production purposes. The purpose of the Thesis was to examine the utilization possibilities of Meat and bone meal (MBM) for energy production. The first part of the Thesis consists of theory part. The theory part includes evaluation of basic properties of MBM as a fertilizer and as a fuel, legislative evaluation and evaluation of different burning techniques. The second part of the Thesis consists of burning tests in Energy laboratory of LUT with different mixtures of peat and MBM. The purpose of the burning tests was to identify co-firing possibilities of peat and MBM and emission- and ash properties for peat and MBM.

Customer reference marketing and utilization of social media as an integral part of customer references

The objective of this Bachelor's Thesis is to find out the role of social media in the B-to-B marketing environment of the information technology industry and to discover how IT-firms utilize social media as a part of their customer reference marketing. To reach the objectives the concepts of customer reference marketing and social media are determined. Customer reference marketing can be characterized as one of the most practically relevant but academically relatively overlooked ways in which a company can leverage its customers and delivered solutions and use them as references in its marketing activities. We will cover which external and internal functions customer references have, that contribute to the growth and performance of B-to-B firms. We also address the three mechanisms of customer reference marketing which are 'status transfer', 'validation through testimonials' and 'demonstration of experience and prior performance'. The concept of social media stands for social interaction and creation of user-based content which exclusively occurs through Internet. The social media are excellent tools for networking because of the fast and easy access, easy interaction and vast amount of multimedia attributes. The allocation of social media is determined. The case company helps clarify the specific characteristics of social media usage as part of customer-reference-marketing activities. For IT-firms the best channels to utilize social media in their customer reference marketing activities are publishing and distribution services of content and networking services.

Efficient installed base information management and utilization in global after sales service business

This Master´s thesis explores how the a global industrial corporation’s after sales service department should arrange its installed base management practices in order to maintain and utilize the installed base information effectively. Case company has product-related records, such as product’s lifecycle information, service history information and information about product’s performance. Information is collected and organized often case by case, therefore the systematic and effective use of installed base information is difficult also the overview of installed base is missing. The goal of the thesis study was to find out how the case company can improve the installed base maintenance and management practices and improve the installed base information availability and reliability. Installed base information management practices were first examined through the literature. The empirical research was conducted by the interviews and questionnaire survey, targeted to the case company’s service department. The research purpose was to find out the challenges related to case company´s service department’s information management practices. The study also identified the installed base information needs and improvement potential in the availability of information. Based on the empirical research findings, recommendations for improve installed base management practices and information availability were created. Grounding of the recommendations, the case company is suggested the following proposals for action: Service report development, improving the change management process, ensuring the quality of the product documentation in early stages of product life cycle and decision to improve installed base management practices.

Natural regeneration in abandoned fields following intensive agricultural land use in an Atlantic Forest Island, Brazil

The time required to regrowth a forest in degraded areas depends on how the forest is removed and on the type of land use following removal. Natural regeneration was studied in abandoned old fields after intensive agricultural land use in areas originally covered by Brazilian Atlantic Forests of the Anchieta Island, Brazil in order to understand how plant communities reassemble following human disturbances as well as to determine suitable strategies of forest restoration. The fields were classified into three vegetation types according to the dominant plant species in: 1) Miconia albicans (Sw.) Triana (Melastomataceae) fields, 2) Dicranopteris flexuosa (Schrader) Underw. (Gleicheniaceae) thickets, and 3) Gleichenella pectinata (Willd.) Ching. (Gleicheniaceae) thickets. Both composition and structure of natural regeneration were compared among the three dominant vegetation types by establishing randomly three plots of 1 x 3 m in five sites of the island. A gradient in composition and abundance of species in natural regeneration could be observed along vegetation types from Dicranopteris fern thickets to Miconia fields. The gradient did not accurately follow the pattern of spatial distribution of the three dominant vegetation types in the island regarding their proximity of the remnant forests. A complex association of biotic and abiotic factors seems to be affecting the seedling recruitment and establishment in the study plots. The lowest plant regeneration found in Dicranopteris and Gleichenella thickets suggests that the ferns inhibit the recruitment of woody and herbaceous species. Otherwise, we could not distinguish different patterns of tree regeneration among the three vegetation types. Our results showed that forest recovery following severe anthropogenic disturbances is not direct, predictable or even achievable on its own. Appropriated actions and methods such as fern removal, planting ground covers, and enrichment planting with tree species were suggested in order to restore the natural forest regeneration process in the abandoned old fields.

Customer-related skills and capabilities in knowledge-intensive business services

The roles of knowledge and customer involvement form distinct features in providing knowledge-intensive business services. The objective of this study was to investigate the customer-related skills and capabilities of knowledge-intensive business services. The research was carried out as case study, involving two polar cases. The other case represented customized services, and the other standardized services. The research method was qualitative, and included focus group workshops, individual interviews and a survey. The capabilities of business services have been mainly studied on organizational level. This study provides valuable insight into the role of individual skills as a part of capabilities of knowledge-intensive business services. According to this study, the most important capabilities are related to acquiring and integrating of knowledge, resource management, managing the customer’s role as a co-producer of the service, and active and effective communication. The study indicates that the level of tacit knowledge is high in the needed individual skills. Based on the study, the needed capabilities and skills are affected by the level of customization of the service, the demand for customer knowledge, the demand for consultation and the stage of the service providing.

Observations on the Pharmacokinetics and Pharmacodynamics of Dexmedetomidine. Clinical Studies on Healthy Volunteers and Intensive Care Patients

Patients treated in intensive care units require sedation and analgesia. However, sedative drugs also have potential adverse effects, and there is no single ideal sedativeanalgesic drug for these patients. Dexmedetomidine is an apha2-adrenoceptor agonist licenced for sedation of intensive care patients and patients undergoing surgery and other invasive procedures. Several routes of parenteral administration (intravenous, intramuscular, subcutaneous and intranasal) have been utilized. In the present series of studies, the pharmacokinetics and pharmacodynamics of intranasally administered dexmedetomidine as well as the gastrointestinal effects of intravenous dexmedetomidine were determined in healthy volunteers. Pharmacokinetics of dexmedetomidine during long lasting, high-dose infusions were characterized in intensive care patients. The bioavailability of intranasal dexmedetomidine was relatively good (65%), but interindividual variation was large. Dexmedetomidine significantly inhibited gastric emptying and gastrointestinal transit. In intensive care patients, the elimination half-life of dexmedetomidine was somewhat longer than reported for infusions of shorter duration and in less ill patients or healthy volunteers. Dexmedetomidine appeared to have linear pharmacokinetics up to the studied dose rate of 2.5 μg/kg/h. Dexmedetomidine clearance was decreasing with age and its volume of distribution was increased in hypoalbuminaemic patients, resulting in a longer elimination half-life and context-sensitive half-time. Intranasally administered dexmedetomidine was efficacious and well tolerated, making it appropriate for clinical situations requiring light sedation. The clinical significance of the gastrointestinal inhibitory effects of dexmedetomidine should be further evaluated in intensive care patients. The possibility of potentially altered potency and effect duration should be taken into account when administering dexmedetomidine to elderly or hypoalbuminaemic patients.

Potential of utilization of rain water excess for irrigation of green roofs in Mato Grosso, Brasil

The aim of this study was to identify the relation between the evapotranspirometer demand and the supply of water from local rainfall, evaluating the possibility of using water excess for irrigation of Green Roofs in the State of Mato Grosso, in Brazil. The study was done using a series of historical data provided by the National Institute of Meteorology (INMET - Instituto Nacional de Meteorologia) which has official climatological stations in 12 cities and regions of the State. The evapotranspiration values were obtained by the Penman-Monteith method and by the Climatic Water Balance (CWB) by the Thornthwaite and Mather method using Available Water Capacity (AWC) of 12mm. With the CWB the excess and deficit were calculated, which were used for the estimative of the volume and area of a reservoir as a function of a collector area of a roof of 100m² and the volume of supplementary water for irrigation. With the obtained results, it was found that in most investigated regions of the State the use of green roofs is not compromised by the water deficiency. On the other hand, the use of a reservoir to accumulate the rain water excess may be impractical, because it requires a considerable area for installation and also because of the high cost of the land.

Effect of different substrates in aquaponic lettuce production associated with intensive tilapia farming with water recirculation systems

ABSTRACT The integration of fish farming in intensive system and plant production, called "aquaponics" is practiced successfully in countries like the USA, Australia and Europe. In Brazil, this integration has attracted the attention of researchers and producers. In this context, the aim of this study was to evaluate the effect of two substrates (crushed stone number 3, CS III and flexible polyurethane foam, FPF) on the production of aquaponic lettuce, moreover, to show that the residual water from intensive tilapia production provides sufficient qualitative characteristics for competitive production of lettuce without adding commercial fertilizers. The treatment in which FPF was used provided higher concentrations of macro and micronutrients in the shoots, higher production of fresh matter of shoots (95.48 g plant-1) and a larger number of leaves (14.90) relative to CS III. These results were attributed to the lower post-transplanting stress and the higher water retention time provided by the FPF. The residual water from tilapia intensive farming can provide sufficient nutrients for the production of lettuce, making the supplementary fertilization with commercial products unnecessary. Thus, the FPF presents the most suitable conditions to be used as substrate in aquaponics system with recirculation of the residual water from the intensive tilapia farming.

Competence in intensive and critical care nursing - development of a basic assessment scale for graduating nursing students

Intensive and critical care nursing is a speciality in its own right and with its own nature within the nursing profession. This speciality poses its own demands for nursing competencies. Intensive and critical care nursing is focused on severely ill patients and their significant others. The patients are comprehensively cared for, constantly monitored and their vital functions are sustained artificially. The main goal is to win time to cure the cause of the patient’s situation or illness. The purpose of this empirical study was i) to describe and define competence and competence requirements in intensive and critical care nursing, ii) to develop a basic measurement scale for competence assessment in intensive and critical care nursing for graduating nursing students, and iii) to describe and evaluate graduating nursing students’ basic competence in intensive and critical care nursing by seeking the reference basis of self-evaluated basic competence in intensive and critical care nursing from ICU nurses. However, the main focus of this study was on the outcomes of nursing education in this nursing speciality. The study was carried out in different phases: basic exploration of competence (phase 1 and 2), instrumentation of competence (phase 3) and evaluation of competence (phase 4). Phase 1 (n=130) evaluated graduating nursing students’ basic biological and physiological knowledge and skills for working in intensive and critical care with Basic Knowledge Assessment Tool version 5 (BKAT-5, Toth 2012). Phase 2 focused on defining competence in intensive and critical care nursing with the help of literature review (n=45 empirical studies) as well as competence requirements in intensive and critical care nursing with the help of experts (n=45 experts) in a Delphi study. In phase 3 the scale Intensive and Critical Care Nursing Competence Scale (ICCN-CS) was developed and tested twice (pilot test 1: n=18 students and n=12 nurses; pilot test 2: n=56 students and n=54 nurses). Finally, in phase 4, graduating nursing students’ competence was evaluated with ICCN-CS and BKAT version 7 (Toth 2012). In order to develop a valid assessment scale of competence for graduating nursing students and to evaluate and establish the competence of graduating nursing students, empirical data were retrieved at the same time from both graduating nursing students (n=139) and ICU nurses (n=431). Competence can be divided into clinical and general professional competence. It can be defined as a specific knowledge base, skill base, attitude and value base and experience base of nursing and the personal base of an intensive and critical care nurse. Personal base was excluded in this self-evaluation based scale. The ICCN-CS-1 consists of 144 items (6 sum variables). Finally, it became evident that the experience base of competence is not a suitable sum variable in holistic intensive and critical care competence scale for graduating nursing students because of their minor experience in this special nursing area. ICCN-CS-1 is a reliable and tolerably valid scale for use among graduating nursing students and ICU nurses Among students, basic competence of intensive and critical care nursing was self-rated as good by 69%, as excellent by 25% and as moderate by 6%. However, graduating nursing students’ basic biological and physiological knowledge and skills for working in intensive and critical care were poor. The students rated their clinical and professional competence as good, and their knowledge base and skill base as moderate. They gave slightly higher ratings for their knowledge base than skill base. Differences in basic competence emerged between graduating nursing students and ICU nurses. The students’ self-ratings of both their basic competence and clinical and professional competence were significantly lower than the nurses’ ratings. The students’ self-ratings of their knowledge and skill base were also statistically significantly lower than nurses’ ratings. However, both groups reported the same attitude and value base, which was excellent. The strongest factor explaining students’ conception of their competence was their experience of autonomy in nursing. Conclusions: Competence in intensive and critical care nursing is a multidimensional concept. Basic competence in intensive and critical care nursing can be measured with self-evaluation based scale but alongside should be used an objective evaluation method. Graduating nursing students’ basic competence in intensive and critical care nursing is good but their knowledge and skill base are moderate. Especially the biological and physiological knowledge base is poor. Therefore in future in intensive and critical care nursing education should be focused on both strengthening students’ biological and physiological knowledge base and on strengthening their overall skill base. Practical implications are presented for nursing education, practice and administration. In future, research should focus on education methods and contents, mentoring of clinical practice and orientation programmes as well as further development of the scale.

Optimization as a method of search engine marketing

This study is dedicated to search engine marketing (SEM). It aims for developing a business model of SEM firms and to provide explicit research of trustworthy practices of virtual marketing companies. Optimization is a general term that represents a variety of techniques and methods of the web pages promotion. The research addresses optimization as a business activity, and it explains its role for the online marketing. Additionally, it highlights issues of unethical techniques utilization by marketers which created relatively negative attitude to them on the Internet environment. Literature insight combines in the one place both technical and economical scientific findings in order to highlight technological and business attributes incorporated in SEM activities. Empirical data regarding search marketers was collected via e-mail questionnaires. 4 representatives of SEM companies were engaged in this study to accomplish the business model design. Additionally, the fifth respondent was a representative of the search engine portal, who provided insight on relations between search engines and marketers. Obtained information of the respondents was processed qualitatively. Movement of commercial organizations to the online market increases demand on promotional programs. SEM is the largest part of online marketing, and it is a prerogative of search engines portals. However, skilled users, or marketers, are able to implement long-term marketing programs by utilizing web page optimization techniques, key word consultancy or content optimization to increase web site visibility to search engines and, therefore, user’s attention to the customer pages. SEM firms are related to small knowledge-intensive businesses. On the basis of data analysis the business model was constructed. The SEM model includes generalized constructs, although they represent a wider amount of operational aspects. Constructing blocks of the model includes fundamental parts of SEM commercial activity: value creation, customer, infrastructure and financial segments. Also, approaches were provided on company’s differentiation and competitive advantages evaluation. It is assumed that search marketers should apply further attempts to differentiate own business out of the large number of similar service providing companies. Findings indicate that SEM companies are interested in the increasing their trustworthiness and the reputation building. Future of the search marketing is directly depending on search engines development.