993 resultados para Linear chain
Resumo:
In the energy management of the isolated operation of small power system, the economic scheduling of the generation units is a crucial problem. Applying right timing can maximize the performance of the supply. The optimal operation of a wind turbine, a solar unit, a fuel cell and a storage battery is searched by a mixed-integer linear programming implemented in General Algebraic Modeling Systems (GAMS). A Virtual Power Producer (VPP) can optimal operate the generation units, assured the good functioning of equipment, including the maintenance, operation cost and the generation measurement and control. A central control at system allows a VPP to manage the optimal generation and their load control. The application of methodology to a real case study in Budapest Tech, demonstrates the effectiveness of this method to solve the optimal isolated dispatch of the DC micro-grid renewable energy park. The problem has been converged in 0.09 s and 30 iterations.
Resumo:
Electricity market players operating in a liberalized environment requires access to an adequate decision support tool, allowing them to consider all the business opportunities and take strategic decisions. Ancillary services represent a good negotiation opportunity that must be considered by market players. For this, decision support tools must include ancillary market simulation. This paper proposes two different methods (Linear Programming and Genetic Algorithm approaches) for ancillary services dispatch. The methodologies are implemented in MASCEM, a multi-agent based electricity market simulator. A test case concerning the dispatch of Regulation Down, Regulation Up, Spinning Reserve and Non-Spinning Reserve services is included in this paper.
Resumo:
RESUMO: Introdução – A Radioterapia (RT) é uma abordagem terapêutica para tratamento de neoplasia de mama. Contudo, diferentes técnicas de irradiação (TI) podem ser usadas. Objetivos – Comparar 4 TI, considerando a irradiação dos volumes alvo (PTV) e dos órgãos de risco (OAR). Metodologia – Selecionaram-se 7 pacientes com indicação para RT de mama esquerda. Sobre tomografia computorizada foram feitos os contornos do PTV e dos OAR. Foram calculadas 4 planimetrias/paciente para as TI: conformacional externa (EBRT), intensidade modulada com 2 (IMRT2) e 5 campos (IMRT5) e arco dinâmico (DART). Resultados – Histogramas de dose volume foram comparados para todas as TI usando o software de análise estatística, IBM SPSS v20. Com IMRT5 e DART, os OAR recebem mais doses baixas. No entanto, IMRT5 apresenta melhores índices de conformidade e homogeneidade para o PTV. Conclusões – IMRT5 apresenta o melhor índice de conformidade; EBRT e IMRT2 apresentam melhores resultados que DART. Há d.e.s entre as TI, sobretudo em doses mais baixas nos OAR.
Resumo:
OBJETIVO: Identificar os determinantes da desnutrição energético-protéica que ocasionam déficits ponderal e de crescimento linear em crianças. MÉTODOS: Estudo transversal envolvendo 1.041 crianças (menores de dois anos de idade) de 10 municípios do Estado da Bahia, de 1999 a 2000. Utilizou-se a técnica de regressão logística e estratégia da abordagem hierárquica para identificar os fatores associados ao estado antropométrico. RESULTADOS: O modelo final para déficit no crescimento linear revelou como determinante básico: a posse de dois ou menos equipamentos domésticos (OR=2,9; IC 95%: 1,74-4,90) e no nível subjacente, a ausência de consulta pré-natal (OR=2,7; IC 95%: 1,47-4,97); entre os determinantes imediatos o baixo peso ao nascer (<2.500 g) (OR=3,6; IC 95%: 1,72-7,70) e relato de hospitalização nos 12 meses anteriores à entrevista (OR=2,4; IC 95%: 1,42-4,10). Fatores determinantes no déficit ponderal nos níveis básico, subjacente e imediato foram, respectivamente: a renda mensal per capita inferior a ¼ do salário-mínimo (OR=3,4; IC 95%: 1,41-8,16), a ausência de pré-natal (OR=2,1; IC 95%: 1,03-4,35), e o baixo peso ao nascer (OR=4,8; IC 95%: 2,00-11,48). CONCLUSÕES: Os déficits ponderal e linear das crianças foram explicados pela intermediação entre as precárias condições materiais de vida e o restrito acesso ao cuidado com a saúde e a carga de morbidade. Intervenções que melhorem as condições de vida e ampliem o acesso às ações do serviço de saúde são estratégias que caminham na busca da eqüidade em saúde e nutrição na infância.
Resumo:
OBJETIVO: Estratégias metodológicas vêm sendo desenvolvidas para minimizar o efeito do erro de medida da dieta. O objetivo do estudo foi descrever a aplicação de uma estratégia para correção da informação dietética pelo erro de medida. MÉTODOS: Foram obtidos dados de consumo alimentar pela aplicação do Questionário de Freqüência Alimentar a 79 adolescentes do Município de São Paulo em 1999. Os dados dietéticos obtidos foram corrigidos por meio de regressão linear, após o ajuste pela energia usando-se o método dos resíduos. O método de referência utilizado foi o recordatório de 24 horas, aplicado em três momentos distintos. RESULTADOS: Os valores corrigidos aproximaram-se dos valores de referência. O fator de correção lambda foi de 0,89 para energia. Para os macronutrientes, os fatores foram de 0,41; 0,22 e 0,20, para carboidratos, lipídios e proteínas, respectivamente. CONCLUSÕES: As médias e desvios-padrão dos valores corrigidos denotam que houve uma correção do erro de medida. Apesar disso, debate-se o desempenho desses métodos, que são notoriamente imperfeitos quando seus pressupostos teóricos não são atendidos, o que é comum nos estudos da dieta que usam instrumentos de medida baseados no relato dos indivíduos.
Resumo:
A 9.9 kb DNA fragment from the right arm of chromosome VII of Saccharomyces cerevisiae has been sequenced and analysed. The sequence contains four open reading frames (ORFs) longer than 100 amino acids. One gene, PFK1, has already been cloned and sequenced and the other one is the probable yeast gene coding for the beta-subunit of the succinyl-CoA synthetase. The two remaining ORFs share homology with the deduced amino acid sequence (and their physical arrangement is similar to that) of the YHR161c and YHR162w ORFs from chromosome VIII.
Resumo:
A 17.6 kb DNA fragment from the right arm of chromosome VII of Saccharomyces cerevisiae has been sequenced and analysed. The sequence contains twelve open reading frames (ORFs) longer than 100 amino acids. Three genes had already been cloned and sequenced: CCT, ADE3 and TR-I. Two ORFs are similar to other yeast genes: G7722 with the YAL023 (PMT2) and PMT1 genes, encoding two integral membrane proteins, and G7727 with the first half of the genes encoding elongation factors 1gamma, TEF3 and TEF4. Two other ORFs, G7742 and G7744, are most probably yeast orthologues of the human and Paracoccus denitrificans electron-transferring flavoproteins (beta chain) and of the Escherichia coli phosphoserine phosphohydrolase. The five remaining identified ORFs do not show detectable homology with other protein sequences deposited in data banks. The sequence has been deposited in the EMBL data library under Accession Number Z49133.
Resumo:
Dissertação de Mestrado em Ciências Económicas e Empresariais.
Resumo:
Background: The effect of the intake of polynsaturated long chain fatty acids (LCPUFAs) during pregnancy on fetal body composition has been assessed by studies using mostly neonatal anthropometry. Their results have been inconsistent, probably because neonatal anthropometry has several validity limitations. Air displacement plethismography (ADP) is a recently validated non-invasive method for assessing body composition in neonates. Objective: To determine the effect of the intake of LCPUFAs during pregnancy on the body composition of term neonates, measured by ADP. Methods: Cross-sectional study of a convenience sample of healthy full-term neonates and their mothers. The diet during pregnancy was assessed using a validated semi-quantitative food frequency questionnaire; Food Processor Plus® was used to convert food intake into nutritional values. Body composition was estimated by anthropometry and measured by ADP using Pea Pod™ Life Measurements Inc (fat mass - FM, fat-free mass and %FM) within the first 72h after birth. Univariate and multivariate analysis (linear regression model) were performed. Results: 54 mother-neonate pairs were included. Multivariate analysis adjusted to the maternal body mass index shows positive association between LCPUFAs intake and neonatal mid-arm circumference (= 0,610, p = 0,019) and negative association between n-6:n-3 ratio intake and neonatal %FM (= -2,744, p=0,066). Conclusion: To the best of our knowledge, this is the first study on this subject using ADP and showing a negative association between LCPUFAs n-6:n-3 ratio intake in pregnancy and neonatal %FM. This preliminary finding requires confirmation increasing the study power with a greater sample and performing interventional studies.
Resumo:
As indústrias de componentes e acessórios automóveis são um elo fundamental no processo produtivo da indústria automóvel. Neste leque industrial encontra-se a Preh Portugal, Lda, como empresa fornecedora de componentes electrónicos, mais concretamente, painéis de controlo de climatização. Os painéis fornecidos pela Preh aos seus clientes encontram-se sujeitos a rigorosos testes de qualidade e funcionalidade. Neste sentido o teste funcional das teclas surge, relacionando o curso da tecla em função de uma força actuante. Esta relação está comprometida com uma curva característica padrão para o tipo de tecla. Para além destes compromissos, também é necessário que a tecla feche e abra o seu contacto eléctrico. Esta tese foca-se no desenvolvimento do teste de teclas, apresentando uma alteração ao sistema actual com a introdução de um sistema embebido, no intuito de flexibilizar o sistema de teste e reduzindo custos. O sistema embebido pretende dar capacidade de processamento ao teste e, desta forma, substituir o actual computador como elemento de processamento. A solução implementada consistiu numa mudança estrutural, através da inclusão do sistema embebido entre o computador e o sistema de deslocamento. Passando o foco central do processo de teste a residir no sistema embebido, este tem de estabelecer comunicações com os restantes elementos intervenientes no teste. Estabelece comunicações série RS-232 com o sistema de deslocamento (leitura do curso e força na tecla), Ethernet com o computador (comandos, parâmetros e resultados) e CAN com o painel de controlo de climatização (fecho/abertura do contacto eléctrico). A concretização deste projecto resultou numa nova estrutura e aplicação, a qual é facilmente integrada na linha de produção com as vantagens de ser menos onerosa e mais flexível, conforme o pretendido.
Resumo:
OBJETIVO: Compreender diferentes lógicas de autonomia presentes nos conflitos entre prescrições cirúrgicas e expectativas de pacientes com diagnóstico de câncer. PROCEDIMENTOS METODOLÓGICOS: Estudo qualitativo, no qual foram realizadas 11 entrevistas semi-estruturadas com cirurgiões oncológicos especializados em tumores de cabeça e pescoço da cidade do Rio de Janeiro, RJ, entre 2000 e 2005. Os participantes foram selecionados por chain sampling e a interrupção do trabalho de campo obedeceu ao critério de saturação. Utilizando-se a técnica de análise de discurso, buscou-se identificar as premissas estruturantes do conceito de autonomia, que comporiam uma dialética discursiva no contexto dos pacientes que relutam em se submeter a cirurgias consideradas mutiladoras. ANÁLISE DOS RESULTADOS: Inicialmente, os cirurgiões exibiram assertivas padronizadas, centradas em conceitos deontológicos de autonomia. À medida que narravam suas experiências, foram observados auto-questionamentos que expunham contradições quanto ao conceito cotidiano de "ressecabilidade informada". Neste ponto os discursos padronizados se deixam permear por auto-questionamentos sobre a necessidade de um retorno ao equilíbrio existencial prejudicado pelo câncer. CONCLUSÕES: As narrativas expressaram demandas por uma "autonomia de equilíbrios" na forma de um semi-projeto não idealizável aprioristicamente, embora dependente de interações com o outro. Os resultados indicam a necessidade de reflexão perante o conceito de autonomia como premissa linear, categórica e individual que, embora superficialmente elaborada, têm governado as ações cotidianas.
Resumo:
In basaltic dykes the magnetic lineation K1 (maximum magnetic susceptibility axis) is generally taken to indicate the flow direction during solidification of the magma. This assumption was tested in Tertiary basaltic dykes from Greenland displaying independent evidence of subhorizontal flow. The digital processing of microphotographs from thin sections cut in (K1, K2) planes yields the preferred linear orientation of plagioclase, which apparently marks the magma flow lineation. In up to 60% of cases, the angular separation between K1 and the assumed flow direction is greater than 45degrees. This suggests that the uncorroborated use of magnetic lineations in dykes is risky. A simple geometrical method is proposed to infer the flow vector from AMS in dykes based solely on magnetic foliations.
Resumo:
Chpater in Book Proceedings with Peer Review Second Iberian Conference, IbPRIA 2005, Estoril, Portugal, June 7-9, 2005, Proceedings, Part II
Resumo:
The authors extend their earlier work on the stability of a reacting binary polymer blend with respect to demixing [D. J. Read, Macromolecules 31, 899 (1998); P. I. C. Teixeira , Macromolecules 33, 387 (2000)] to the case where one of the polymers is rod-like and may order nematically. As before, the authors combine the random phase approximation for the free energy with a Markov chain model for the chemistry to obtain the spinodal as a function of the relevant degrees of reaction. These are then calculated by assuming a simple second-order chemical kinetics. Results are presented, for linear systems, which illustrate the effects of varying the proportion of coils and rods, their relative sizes, and the strength of the nematic interaction between the rods. (c) 2007 American Institute of Physics.
Resumo:
We use a simple model of associating fluids which consists of spherical particles having a hard-core repulsion, complemented by three short-ranged attractive sites on the surface (sticky spots). Two of the spots are of type A and one is of type B; the bonding interactions between each pair of spots have strengths epsilon(AA), epsilon(BB), and epsilon(AB). The theory is applied over the whole range of bonding strengths and the results are interpreted in terms of the equilibrium cluster structures of the phases. In addition to our numerical results, we derive asymptotic expansions for the free energy in the limits for which there is no liquid-vapor critical point: linear chains (epsilon(AA)not equal 0, epsilon(AB)=epsilon(BB)=0), hyperbranched polymers (epsilon(AB)not equal 0, epsilon(AA)=epsilon(BB)=0), and dimers (epsilon(BB)not equal 0, epsilon(AA)=epsilon(AB)=0). These expansions also allow us to calculate the structure of the critical fluid by perturbing around the above limits, yielding three different types of condensation: of linear chains (AA clusters connected by a few AB or BB bonds); of hyperbranched polymers (AB clusters connected by AA bonds); or of dimers (BB clusters connected by AA bonds). Interestingly, there is no critical point when epsilon(AA) vanishes despite the fact that AA bonds alone cannot drive condensation.