Implementação em FPGA de um Modem QPSK

Esta dissertação insere-se num conjunto de trabalhos a decorrer no Instituto de Telecomunicações de Aveiro que tem como objetivo o desenvolvimento de um sistema de comunicação para um UAV. Neste sentido, apresenta a implementação e validação de um modem em banda base aberto e flexível implementado em FPGA, baseado em abordagem SDR, com possibilidade de integraçãoo no sistema de comunicação com o UAV. Ao longo desta dissertação implementou-se, utilizando o MATLAB, um modem de modulação adaptável, ao qual foram integrados algoritmos de sincronismo e de correção de fase. Desta forma, foi possível realizar uma análise ao modelo comportamental dos vários constituintes do modem abstraindose dos tempos de atraso do processamento ou da precisão da representação dos dados, e assim simplificar a sua implementação em hardware. Analisado o modelo comportamental do modem desenvolvido em MATLAB realizou-se a sua implementação em hardware para a modulação QPSK. A sua prototipagem foi realizada, com recurso à ferramenta computacional Vivado Design Suite 2014.2, utilizando o kit de desenvolvimento ZedBoard e o frontend AD-FMCOMMS1-EBZ. O correto funcionamento dos módulos implementados em hardware foi posteriormente avaliado através de uma interface entre o MATLAB e a Zed- Board, sendo que, os resultados obtidos no modelo em MATLAB serviram como termo de comparação. Através da utilização desta interface é possível validar parte do modem implementado em FPGA, mantendo o restante processamento a ser realizado em MATLAB, validando assim os módulos em FPGA de uma forma isolada.

Operating infrastructure for an FPGA and ARM system

Advances in FPGA technology and higher processing capabilities requirements have pushed to the emerge of All Programmable Systems-on-Chip, which incorporate a hard designed processing system and a programmable logic that enable the development of specialized computer systems for a wide range of practical applications, including data and signal processing, high performance computing, embedded systems, among many others. To give place to an infrastructure that is capable of using the benefits of such a reconfigurable system, the main goal of the thesis is to implement an infrastructure composed of hardware, software and network resources, that incorporates the necessary services for the operation, management and interface of peripherals, that coompose the basic building blocks for the execution of applications. The project will be developed using a chip from the Zynq-7000 All Programmable Systems-on-Chip family.

Arquitetura híbrida com DSP e FPGA para implementação de controladores de filtros ativos de potência

The presence of non-linear loads at a point in the distribution system may deform voltage waveform due to the consumption of non-sinusoidal currents. The use of active power filters allows significant reduction of the harmonic content in the supply current. However, the processing of digital control structures for these filters may require high performance hardware, particularly for reference currents calculation. This work describes the development of hardware structures with high processing capability for application in active power filters. In this sense, it considers an architecture that allows parallel processing using programmable logic devices. The developed structure uses a hybrid model using a DSP and an FPGA. The DSP is used for the acquisition of current and voltage signals, calculation of fundamental current related controllers and PWM generation. The FPGA is used for intensive signal processing, such as the harmonic compensators. In this way, from the experimental analysis, significant reductions of the processing time are achieved when compared to traditional approaches using only DSP. The experimental results validate the designed structure and these results are compared with other ones from architectures reported in the literature.

Principios del FPGA y aplicaciones en el control de procesos industriales

La presente investigación muestra los pasos sugeridos para introducirse a la creación de sistemas electrónicos programables a través de la tecnología FPGA. Un FPGA es un dispositivo programable de alta capacidad que puede ser utilizado para la creación de sistemas digitales de control y automatización de procesos. La investigación se divide en cuatro capítulos estructurados de la siguiente forma: Capítulo I- Teoría general: Abarca las características básicas de los FPGA en general y las del equipo a utilizar; Capítulo II-Software: Consta de un manual de usuario sobre el software utilizado en la investigación; Capítulo III-Laboratorios: Una serie de laboratorios prácticos; Capítulo IV- Aplicaciones: Metodología y ejemplo

Implementação em FPGA de compensadores de desvios para conversor analógico digital intercalado

This work presents the modeling and FPGA implementation of digital TIADC mismatches compensation systems. The development of the whole work follows a top-down methodology. Following this methodology was developed a two channel TIADC behavior modeling and their respective offset, gain and clock skew mismatches on Simulink. In addition was developed digital mismatch compensation system behavior modeling. For clock skew mismatch compensation fractional delay filters were used, more specifically, the efficient Farrow struct. The definition of wich filter design methodology would be used, and wich Farrow structure, required the study of various design methods presented in literature. The digital compensation systems models were converted to VHDL, for FPGA implementation and validation. These system validation was carried out using the test methodology FPGA In Loop . The results obtained with TIADC mismatch compensators show the high performance gain provided by these structures. Beyond this result, these work illustrates the potential of design, implementation and FPGA test methodologies.

Diseño e implementación en FPGA de un filtro de partículas para aplicaciones biomédicas

La diabetes mellitus tipo 1 (DM1) es una enfermedad crónica caracterizada por la incapacidad del páncreas de producir insulina. Esta hormona regula la absorción de la glucosa del torrente sanguíneo por parte de las células. Debido a la ausencia de insulina en el cuerpo, la glucosa se acumula en el torrente sanguíneo provocando problemas a corto y largo plazo, como por ejemplo deterioro celular. Los pacientes con esta enfermedad necesitan controlar su glucemia (concentración de glucosa en sangre) midiendo la misma de forma regular e inyectándose insulina subcutánea de por vida. Para conocer la glucemia se pueden utilizar Monitores Continuos de Glucosa (MCG), que proporcionan el valor de la glucosa intersticial en un rango entre uno y cinco minutos. Los MCG actuales presentan los siguientes problemas: Por un lado, el sensor que lleva incorporado introduce ruidos asociados a la medición obtenida. Y, por otro lado, el sensor se degrada a lo largo de su vida útil, lo que dificulta la interpretación de los datos obtenidos. La solución propuesta en este trabajo consiste en la utilización de filtros de partículas. Este tipo de filtros consta de cuatro fases: inicialización, predicción, corrección y remuestreo. Son capaces de identificar los estados ocultos del sistema (glucosa en sangre y degeneración del sensor), a partir de medidas indirectas del mismo (como por ejemplo la glucosa intersticial) teniendo en cuenta el ruido de las mediciones del MCG. En este proyecto se va a aplicar un filtro de partículas de cuatro estados (glucosa, velocidad de variación de la glucosa, degeneración del sensor y velocidad de variación de la degeneración del sensor.). En primera instancia, se utilizará la herramienta Matlab para analizar el correcto funcionamiento de este algoritmo frente a los problemas mencionados anteriormente de los MCG. Y, en segundo lugar, se realizará una implementación hardware sobre una FPGA.

Establishing community advisory boards for clinical trial research in Malawi: engendering ethical conduct in research

In this article I deal with extending the ethical principles of research to include communities through the establishment of Community Advisory Boards (CABs). The aim of the project on which this article is based demonstrates the need for protecting communities that participate in research in order to stimulate ethical conduct in research in Malawi. In the article, I provide an overview on the role and functions of CABs. I discuss the establishment of CABs in Malawi and present descriptions of the processes and challenges involved. I conclude by sharing experiences of some of the key lessons learnt from the establishment of CABs.

A Study of the Robustness Against SEUs of Digital Circuits Implemented with FPGA DSPs

In this paper we present an experimental validation of the reliability increase of digital circuits implemented in XilinxTMFPGAs when they are implemented using the DSPs (Digital Signal Processors) that are available in the reconfigurable device. For this purpose, we have used a fault-injection platform developed by our research group, NESSY [1]. The presented experiments demonstrate that the probability of occurrence of a SEU effect is similar both in the circuits implemented with and without using embedded DSPs. However, the former are more efficient in terms of area usage, which leads to a decrease in the probability of a SEU occurrence.

Optical Waveguides and Structures for Short Haul Optical Communication Channels within Printed Circuit Boards

Optical waveguides have shown promising results for use within printed circuit boards. These optical waveguides have higher bandwidth than traditional copper transmission systems and are immune to electromagnetic interference. Design parameters for these optical waveguides are needed to ensure an optimal link budget. Modeling and simulation methods are used to determine the optimal design parameters needed in designing the waveguides. As a result, optical structures necessary for incorporating optical waveguides into printed circuit boards are designed and optimized. Embedded siloxane polymer waveguides are investigated for their use in optical printed circuit boards. This material was chosen because it has low absorption, high temperature stability, and can be deposited using common processing techniques. Two sizes of waveguides are investigated, 50 $unit{mu m}$ multimode and 4 - 9 $unit{mu m}$ single mode waveguides. A beam propagation method is developed for simulating the multimode and single mode waveguide parameters. The attenuation of simulated multimode waveguides are able to match the attenuation of fabricated waveguides with a root mean square error of 0.192 dB. Using the same process as the multimode waveguides, parameters needed to ensure a low link loss are found for single mode waveguides including maximum size, minimum cladding thickness, minimum waveguide separation, and minimum bend radius. To couple light out-of-plane to a transmitter or receiver, a structure such as a vertical interconnect assembly (VIA) is required. For multimode waveguides the optimal placement of a total internal reflection mirror can be found without prior knowledge of the waveguide length. The optimal placement is found to be either 60 µm or 150 µm away from the end of the waveguide depending on which metric a designer wants to optimize the average output power, the output power variance, or the maximum possible power loss. For single mode waveguides a volume grating coupler is designed to couple light from a silicon waveguide to a polymer single mode waveguide. A focusing grating coupler is compared to a perpendicular grating coupler that is focused by a micro-molded lens. The focusing grating coupler had an optical loss of over -14 dB, while the grating coupler with a lens had an optical loss of -6.26 dB.

Direct Write Fabrication of Waveguides and Interconnects for Optical Printed Wiring Boards

Current copper based circuit technology is becoming a limiting factor in high speed data transfer applications as processors are improving at a faster rate than are developments to increase on board data transfer. One solution is to utilize optical waveguide technology to overcome these bandwidth and loss restrictions. The use of this technology virtually eliminates the heat and cross-talk loss seen in copper circuitry, while also operating at a higher bandwidth. Transitioning current fabrication techniques from small scale laboratory environments to large scale manufacturing presents significant challenges. Optical-to-electrical connections and out-of-plane coupling are significant hurdles in the advancement of optical interconnects. The main goals of this research are the development of direct write material deposition and patterning tools for the fabrication of waveguide systems on large substrates, and the development of out-of-plane coupler components compatible with standard fiber optic cabling. Combining these elements with standard printed circuit boards allows for the fabrication of fully functional optical-electrical-printed-wiring-boards (OEPWBs). A direct dispense tool was designed, assembled, and characterized for the repeatable dispensing of blanket waveguide layers over a range of thicknesses (25-225 µm), eliminating waste material and affording the ability to utilize large substrates. This tool was used to directly dispense multimode waveguide cores which required no UV definition or development. These cores had circular cross sections and were comparable in optical performance to lithographically fabricated square waveguides. Laser direct writing is a non-contact process that allows for the dynamic UV patterning of waveguide material on large substrates, eliminating the need for high resolution masks. A laser direct write tool was designed, assembled, and characterized for direct write patterning waveguides that were comparable in quality to those produced using standard lithographic practices (0.047 dB/cm loss for laser written waveguides compared to 0.043 dB/cm for lithographic waveguides). Straight waveguides, and waveguide turns were patterned at multimode and single mode sizes, and the process was characterized and documented. Support structures such as angled reflectors and vertical posts were produced, showing the versatility of the laser direct write tool. Commercially available components were implanted into the optical layer for out-of-plane routing of the optical signals. These devices featured spherical lenses on the input and output sides of a total internal reflection (TIR) mirror, as well as alignment pins compatible with standard MT design. Fully functional OEPWBs were fabricated featuring input and output out-of-plane optical signal routing with total optical losses not exceeding 10 dB. These prototypes survived thermal cycling (-40°C to 85°C) and humidity exposure (95±4% humidity), showing minimal degradation in optical performance. Operational failure occurred after environmental aging life testing at 110°C for 216 hours.

Implémentation sur FPGA de l’algorithme MUSIC sur antenne-réseau expérimentale à 10 GHz

Les techniques des directions d’arrivée (DOA) sont une voie prometteuse pour accroitre la capacité des systèmes et les services de télécommunications en permettant de mieux estimer le canal radio-mobile. Elles permettent aussi de suivre précisément des usagers cellulaires pour orienter les faisceaux d’antennes dans leur direction. S’inscrivant dans ce contexte, ce présent mémoire décrit étape par étape l’implémentation de l’algorithme de haut niveau MUSIC (MUltiple SIgnal Classification) sur une plateforme FPGA afin de déterminer en temps réel l’angle d’arrivée d’une ou des sources incidentes à un réseau d’antennes. Le concept du prototypage rapide des lois de commande (RCP) avec les outils de XilinxTM System generator (XSG) et du MBDK (Model Based Design Kit) de NutaqTM est le concept de développement utilisé. Ce concept se base sur une programmation de code haut niveau à travers des modèles, pour générer automatiquement un code de bas niveau. Une attention particulière est portée sur la méthode choisie pour résoudre le problème de la décomposition en valeurs et vecteurs propres de la matrice complexe de covariance par l’algorithme de Jacobi. L’architecture mise en place implémentant cette dernière dans le FPGA (Field Programmable Gate Array) est détaillée. Par ailleurs, il est prouvé que MUSIC ne peut effectuer une estimation intéressante de la position des sources sans une calibration préalable du réseau d’antennes. Ainsi, la technique de calibration par matrice G utilisée dans ce projet est présentée, en plus de son modèle d’implémentation. Enfin, les résultats expérimentaux du système mis à l’épreuve dans un environnement réel en présence d’une source puis de deux sources fortement corrélées sont illustrés et analysés.

Training and Updating of Education Boards in Indigenous Schools of Rural Areas: Strengthening Local Education Management

Education management in the schools of indigenous rural areas faces a number of difficulties to implement and comply with the guidelines and requirements of the laws related to budgetary management of resources allocated to Education or Administrative Boards. In addition to being located in scattered rural areas, far from the municipal heads and regional offices of the Ministry of Public Education, one of the main obstacles is that all regulations, laws and guidelines are written in Spanish, and there is people, in this indigenous rural communities, who do not speak, write, read or understand this language. This puts them at an enormous disadvantage, which has a direct impact on the indigenous children’s right to education.

Employment of Real-Time/FPGA Architectures for Test and Control of Automotive Engines

Nowadays the production of increasingly complex and electrified vehicles requires the implementation of new control and monitoring systems. This reason, together with the tendency of moving rapidly from the test bench to the vehicle, leads to a landscape that requires the development of embedded hardware and software to face the application effectively and efficiently. The development of application-based software on real-time/FPGA hardware could be a good answer for these challenges: FPGA grants parallel low-level and high-speed calculation/timing, while the Real-Time processor can handle high-level calculation layers, logging and communication functions with determinism. Thanks to the software flexibility and small dimensions, these architectures can find a perfect collocation as engine RCP (Rapid Control Prototyping) units and as smart data logger/analyser, both for test bench and on vehicle application. Efforts have been done for building a base architecture with common functionalities capable of easily hosting application-specific control code. Several case studies originating in this scenario will be shown; dedicated solutions for protype applications have been developed exploiting a real-time/FPGA architecture as ECU (Engine Control Unit) and custom RCP functionalities, such as water injection and testing hydraulic brake control.

Prototipazione FPGA di sottosistemi integrati per power management basati su ISA RISC-V

Fino a 15 anni fa, era possibile aumentare il numero di transistor su un singolo chip e contemporaneamente la sua frequenza di clock mantenendo la densità di potenza costante. Tuttavia dal 2004 non è più possibile mantenere invariata la potenza dissipata per unità d’area a causa di limitazioni fisiche. Al fine di aumentare le performance dei processori e di impedire una diminuzione delle frequenze di clock, i processori moderni integrano on-die dei Power Controller Subsystems (PCS) come risorsa hardware dedicata che implementa complesse strategie di gestione di temperatura e potenza. In questo progetto di tesi viene progettata l'architettura dell'interfaccia di comunicazione di ControlPULP, un PCS basato su ISA RISC-V, per la connessione verso un processore HPC. Tale interfaccia di comunicaione integra il supporto hardware per lo scambio di messaggi secondo la specifica SCMI. L'interfaccia sviluppata viene successivamente validata attraverso simulazione ed emulazione su supporto hardware FPGA. Tale supporto hardware viene inoltre utilizzato per la caratterizzazione dell'utilizzo di risorse dell'architettura progettata. Oltre allo sviluppo dell'interfaccia hardware viene sviluppato e caratterizzato un firmware per la decodifica dei messaggi SCMI conforme ai requisiti di esecuzione su un sistema real-time.

Progettazione e ottimizzazione di un Turbo Encoder parallelo su dispositivo FPGA

In questi anni, c’è stato un grande sviluppo negli standard wireless nel mondo della televisione, della radio e delle comunicazioni mobili. Questo ha portato con sé problemi di compatibilità tra le reti wireless e ha limitato lo sviluppo di nuove funzionalità e servizi. La Software Defined Radio rappresenta una soluzione di flessibilità per affrontare questa serie di problematiche. In un sistema di comunicazione digitale, le informazioni viaggiano su un canale che è soggetto a rumore ed interferenza; perciò, per garantire robustezza e affidabilità alle applicazioni nella comunicazione digitale, i sistemi richiedono l’uso di codici di correzione degli errori, basati su schemi di codifica di canale. Esistono diverse tipologie di codici per la correzione degli errori, tra le quali il turbo codice, utilizzato nei sistemi LTE. Questo lavoro presenta la progettazione e la successiva ottimizzazione di un turbo encoder per sistemi LTE su una scheda FPGA, la quale, a differenza di altri dispositivi, meglio si presta a questo scopo, grazie alla caratteristica di riprogrammabilità. Dapprima viene presentato un turbo encoder sequenziale, il quale viene ottimizzato creandone una versione parallela. I risultati mostrano che l’architettura parallela presenta prestazioni, in termini di throughput, quattro volte migliori di quella sequenziale, a fronte di un lieve aumento dell’uso delle risorse della scheda. Confrontando questo turbo encoder ottimizzato con un progetto presente in letteratura, si nota che l’efficienza d’area risulta maggiore con un fattore circa pari a 3.