Estudo para a optimização dos sistemas de climatização com vista à obtenção de um edifício com baixas necessidades energéticas em climatização

A presente tese tem como principal objectivo abordar o tema da eficiência energética em edifícios, no que se refere aos sistemas de climatização. O desenvolvimento deste projecto realizou-se em torno dos consumos energéticos dos diferentes sistemas de climatização estudados (e por conseguinte da envolvente do edifício), focando o cumprimento dos requisitos térmico e energéticos das normas vigentes (RCCTE e RSECE) em Portugal, tendo como objectivo identificar os parâmetros com maior impacto e a relação tendencial entre as soluções construtivas e tecnológicas adoptadas, sempre com o horizonte de maximizar a eficiência energética e diminuir a dependência face à energia primária e consequentemente a emissão de gases que provocam o efeito de estufa. É âmbito desta tese comparar diferentes tipos de sistemas de climatização a nível energético e torná-los os mais eficientes possíveis, para que também se possam tornar monetariamente aliciantes e aumentar o rácio entre benefício/custo. Para tal, numa primeira fase foi feito um estudo térmico da envolvente do edifício, tendo sido utilizado um software de simulação energética de edifícios acreditado pela norma ASHRAE 140-2004 para se poder compreender como o edifício se comportava ao longo do ano, e introduzir algumas correcções na respectiva envolvente, para baixar as potências térmicas/eléctricas dos equipamentos do sistema de AVAC. De seguida foram estudados três sistemas possíveis de climatização para o edifício, de modo a identificar o mais eficiente numa base anual, bem como a possibilidade de combinar o uso de fontes de energia renováveis com o intuito de satisfazer ao máximo as necessidades térmicas do edifício e, ainda, de minimizar o consumo de energia de origem não renovável. Por fim, para avaliar as diferentes potencialidades de cada sistema de climatização estudado, fez-se o respectivo estudo à sua viabilidade económica. Nas considerações finais da presente tese é realizado um estudo aos benefícios que uma possível alteração da arquitectura do edifício pode trazer no aumento da iluminação natural do mesmo integrado com um controlo da iluminação artificial necessária para os diferentes espaços climatizados. Os resultados obtidos foram comparados entre si e corrigir a envolvente exterior reduz os consumos energéticos do edifício em cerca de 11%. As medidas correctivas propostas no sistema de climatização base originam uma redução energética igual a 43%. A nível ambiental, é possível a redução do número de emissões de CO2 em cerca de 72.1%.

Simulations of parasitic and intrinsic capacitances related to Multiple-Gate-Field-Effect Transistor architectures

Report for the scientific sojourn carried out at the Université Catholique de Louvain, Belgium, from March until June 2007. In the first part, the impact of important geometrical parameters such as source and drain thickness, fin spacing, spacer width, etc. on the parasitic fringing capacitance component of multiple-gate field-effect transistors (MuGFET) is deeply analyzed using finite element simulations. Several architectures such as single gate, FinFETs (double gate), triple-gate represented by Pi-gate MOSFETs are simulated and compared in terms of channel and fringing capacitances for the same occupied die area. Simulations highlight the great impact of diminishing the spacing between fins for MuGFETs and the trade-off between the reduction of parasitic source and drain resistances and the increase of fringing capacitances when Selective Epitaxial Growth (SEG) technology is introduced. The impact of these technological solutions on the transistor cut-off frequencies is also discussed. The second part deals with the study of the effect of the volume inversion (VI) on the capacitances of undoped Double-Gate (DG) MOSFETs. For that purpose, we present simulation results for the capacitances of undoped DG MOSFETs using an explicit and analytical compact model. It monstrates that the transition from volume inversion regime to dual gate behaviour is well simulated. The model shows an accurate dependence on the silicon layer thickness,consistent withtwo dimensional numerical simulations, for both thin and thick silicon films. Whereas the current drive and transconductance are enhanced in volume inversion regime, our results show thatintrinsic capacitances present higher values as well, which may limit the high speed (delay time) behaviour of DG MOSFETs under volume inversion regime.

Alternativas tecnológicas para la recuperación y valorización del nitrógeno presente en los residuos orgánicos

La conciencia de los problemas asociados a la gestión de los residuos orgánicos y el interés por las oportunidades de su recuperación y valorización han ido tomando importancia en los últimos años, tanto en el campo de las deyecciones ganaderas como en el sector de las aguas residuales. Consecuentemente, las combinaciones tecnológicas que permitan cerrar los ciclos de los nutrientes y la recuperación energética han adquirido mayor importancia en la investigación así como en las nuevas normativas sectoriales. En este contexto se sitúa el trabajo realizado durante el periodo becado (octubre 2010 - noviembre 2011). En una primera etapa de estudio bibliográfico se identificaron i) el aumento de la eficiencia en el uso del nitrógeno en la agricultura y en la ganadería, ii) la reutilización del nitrógeno en los mismos ecosistemas agrícolas y iii) el tratamiento de las deyecciones para redistribuir el nitrógeno a zonas con poca disponibilidad, como las tres direcciones principales hacia las cuales se está focalizando el interés del sector agrícola. Se puso en marcha una planta piloto de stripping y absorción para estudiar la posibilidad de recuperar y valorizar el amoniaco presente en los purines en forma de solución amoniacal para la industria de fertilizantes. Los resultados obtenidos evidenciaron el rol fundamental de las características iníciales del substrato en el rendimiento global del proceso. En particular, elevados contenidos en materia orgánica resultaron en bajas eficiencias y en elevadas contaminaciones del producto obtenido. Finalmente, considerando sus potenciales ventajas tanto en la gestión de los residuos ganaderos como de las aguas residuales y focalizándose en las perdidas de nitrógeno se estudió un sistema descentralizado de separación de orina instalado en un centro de investigación. Los resultados preliminares permitieron caracterizar los principales procesos que ocurren en el sistema e identificar las posibles líneas futuras de investigación.

Sistemes de gestió de continguts en la gestió del coneixement

Since the second half of the 1990s, knowledge management has taken shape and has been firmly consolidated as a new discipline within the realm of organisations. The principal objective of this work is to determine whether content management systems (CMS) can become the most appropriate technological standard for consolidating this field. The article describes and analyses the major functions (publishing and exploitation) of these new systems. It then examines the field of knowledge management ¿what are the different types of knowledge that we can find within an organisational context¿ and then identifies and analyses the operations critical to managing it appropriately. The article concludes by evaluating the extent to which technological solutions provided by CMS can assist in properly implementing these critical operations.

Sistemas de gestión de contenidos en la gestión del conocimiento

Since the second half of the 1990s, knowledge management has taken shape and has been firmly consolidated as a new discipline within the realm of organisations. The principal objective of this work is to determine whether content management systems (CMS) can become the most appropriate technological standard for consolidating this field. The article describes and analyses the major functions (publishing and exploitation) of these new systems. It then examines the field of knowledge management ¿what are the different types of knowledge that we can find within an organisational context¿ and then identifies and analyses the operations critical to managing it appropriately. The article concludes by evaluating the extent to which technological solutions provided by CMS can assist in properly implementing these critical operations.

Mobile ERP in the use of maintenance operations of forest industry

Toiminnanohjausjärjestelmien käyttö on muuttanut metsäteollisuuden kunnossapidon työntekijän toimenkuvaa kunnossapidon perustoiminnoista itseohjautuvampaan tietojen käsittelyyn ja jalostamiseen. Työn tavoitteena oliselvittää mobiilin työtilausjärjestelmän vaikutuksia metsäteollisuuden kunnossapidon kenttätyössä. Mobiilin työtilausjärjestelmän käyttö metsäteollisuuden kunnossapidossa mahdollistaa tärkeän kunnossapitotiedon keräämisen ja tarkentamisen kentällä, jossa se usein on ajanmukaisinta ja tarkinta. Haasteellisinta on oikeanlaisen teknologian löytäminen ja standardoiminen kunnossapidon toimintaympäristöihin. Myös organisaation toimintoprosessien on oltava selkeät ennen kuin prosesseja voidaan tehostaa teknologisin keinoin.

Vanhusten hyvä kotona asuminen: tutkimusta kuntatuottavuudesta, älykodeista ja apuvälinepalveluprosesseista

The purpose of the research was to investigate operational processes related to home care of the elderly as well as use of assistive devices in smart home environments, and operational processes that are generally related to use of assistive devices – from the point of view of productivity improvement. The themes were looked into from the points of view of both the elderly and care personnel. In addition, perspectives of near relatives of the elderly, of the larger service system as well as of companies that provided assistive devices to the smart homes were taken into consideration. In the study of home care processes, 32 customer interviews and 17 employee interviews were carried out. This report contains a summary that is based on a separate report of the home care study. The study of home care was conducted in 2006. The use of technological and mechanical assistive devices and the related operational processes were investigated with the help of the smart home pilot in 2007–2008. The study is described in this report. The smart home pilot was implemented in four different housing service units for elderly people at Lahti, Nastola and Hollola. They were in use during short-term housing periods related to, for instance, end of hospitalisation, holidays of caring relatives and assessment of living and housing conditions. More than 60 different assistive devices and technologies were brought to the smart homes. During the pilot period, experiences of customers and personnel as well as processes related to the use of assistive devices were investigated. The research material consisted of 20 survey questionnaires of personnel and customers, four interviews with customers, five interviews with personnel, feedback survey responses from 14 companies, and other data that were collected, for instance, in orientation events. The research results highlighted the need for tailored services based on an elderly person’s needs and wishes, while taking advantage of innovative and technological solutions. As in the earlier home care study, also assistive device-related operational processes were looked into with the help of concepts of ‘resource focus’, ‘lost motion’ and ‘intermediate landing’. The following were identified as central operational processes in assistive device-related services (regardless of the service provider): (1) acquisition process of technologies and assistive devices as well as of rearrangement and rebuilding works in the home, (2) introduction and orientation process (of the elderly, their relatives and care personnel), (3) information and communication process, and (4) service and monitoring process. In addition, the research focused on design and desirability of assistive devices as well as their costs, such as opportunity costs. The process-based points of view gave new knowledge that may be used in the future to develop service processes and clarify their ownership so that separately managed cross-functional processes could be built with participants from different sectors to operate alongside organisations of elderly care. Development of functionality of assistive device-related services is a societally significant issue.

Yhteistoiminnan ja tiedon jakamisen kehittäminen

Tässä tutkimustyössä on tavoitteena tutkia UPM-Kymmene Wood Oy:n vaneriliiketoimintaorganisaation lähtölogistiikka- ja myyntiosaston tiedon jakamisen ja yhteistoiminnan nykytilaa ja kartoittaa osastojen tiedontarpeita yhteistoimintaan liittyen. Työn tavoitteena on tämän jälkeen antaa kohdeosastoille ehdotuksia toimenpiteistä ja teknologisista ratkaisuista toiminnan parantamiseen. Työssä esitetään aluksi tietoon ja sen jakamiseen liittyviä käsitteitä. Tämän jälkeen tekstissä luodaan katsaus liiketoimintatietoon ja sen hallintaan. Lisäksi tutkimuksessa tarkastellaan tutkimuksen kohteena olevaa organisaatiota ja kohdeosastoja. Haastatteluiden ja havainnoinnin avulla kerätyn tutkimusaineiston perusteella kohdeosastojen välillä vaihdetaan nykytilassa paljon erilaista asiakkaisiin ja markkinoihin liittyvää tietoa. Tiedon jakaminen ja vaihto perustuu kuitenkin nykytilassa hyvin vahvasti säännöllisen yhteistoiminnan sijaan erillisesti ilmaistuihin tietotarpeisiin. Haastatteluiden perusteella kohdeosastoissa on havaittavissa myös parannustarpeita nykyiseen tiedonkulkuun ja tiedon jakamiseen verrattuna. Annetut kehitysehdotukset koskevat yhteistoiminnan muuntamista säännölliseksi ja keskustelevaksi, olemassa olevien tietojen tehokkaammasta jakamisesta ja nykyisten tietohallintajärjestelmien hyödyntämisestä yhteistoiminnassa uusien järjestelmien luomisen sijaan.

Toimittaja-arvioinnin ja toimitusvalvonnan kehittäminen metsäteollisuuden kunnossapitoyrityksessä

Tutkimuksen tavoitteena oli kehittää toimitusvalvontaa ja toimittaja-arviointia metsäteollisuuden kunnossapitoyrityksen toiminnanohjausjärjestelmän sekä toimintatapojen osalta. Tutkimus toteutettiin haastattelemalla yrityksen eri yksiköiden hankintaorganisaatioita sekä valittuja toimittajia ja sidosryhmiä. Tutkimuksessa myös tutustuttiin kohdeyrityksen SAP R/3 -järjestelmän nykyisiin hyödynnettyihin ja hyödyntämättömiin ominaisuuksiin. Työn teoreettinen viitekehys perustui hankintatoiminnan ja kunnossapidon kehityssuuntien sekä soveltuvien teknologisten ratkaisujen tarkasteluun kunnossapitoyrityksen toimintaympäristössä. Tutkimuksessa havaittuja kehitystarpeita arvioitiin järjestelmäasiantuntijoiden ja muodostetun laatukustannusten laskentamallin avulla. Toimittaja-arviointi rajattiin tutkimuksessa koskemaan toimitusvarmuuden ja laatupoikkeamien jatkuvaa, keskitettyä raportoinnin työkalujen hyödyntämistä. Toimitusvalvonnan parantamiseksi arvioitiin kunnossapitotoimintaan ja kunnossapidon hankintoihin soveltuvaa ratkaisua. Kehitysehdotuksia ja suosituksia ilmeni useita ja ne ryhmiteltiin kohdeyrityksen kannalta helposti toteutettaviin tai toimintamalleista johtuviin, kohtalaisia muutoksia vaativiin ja suuria muutoksia vaativiin hankkeisiin.

Phase voltage control and filtering in a converter-fed single-phase customer-end system of the LVDC distribution network

In recent years, the network vulnerability to natural hazards has been noticed. Moreover, operating on the limits of the network transmission capabilities have resulted in major outages during the past decade. One of the reasons for operating on these limits is that the network has become outdated. Therefore, new technical solutions are studied that could provide more reliable and more energy efficient power distributionand also a better profitability for the network owner. It is the development and price of power electronics that have made the DC distribution an attractive alternative again. In this doctoral thesis, one type of a low-voltage DC distribution system is investigated. Morespecifically, it is studied which current technological solutions, used at the customer-end, could provide better power quality for the customer when compared with the current system. To study the effect of a DC network on the customer-end power quality, a bipolar DC network model is derived. The model can also be used to identify the supply parameters when the V/kW ratio is approximately known. Although the model provides knowledge of the average behavior, it is shown that the instantaneous DC voltage ripple should be limited. The guidelines to choose an appropriate capacitance value for the capacitor located at the input DC terminals of the customer-end are given. Also the structure of the customer-end is considered. A comparison between the most common solutions is made based on their cost, energy efficiency, and reliability. In the comparison, special attention is paid to the passive filtering solutions since the filter is considered a crucial element when the lifetime expenses are determined. It is found out that the filter topology most commonly used today, namely the LC filter, does not provide economical advantage over the hybrid filter structure. Finally, some of the typical control system solutions are introduced and their shortcomings are presented. As a solution to the customer-end voltage regulation problem, an observer-based control scheme is proposed. It is shown how different control system structures affect the performance. The performance meeting the requirements is achieved by using only one output measurement, when operating in a rigid network. Similar performance can be achieved in a weak grid by DC voltage measurement. An additional improvement can be achieved when an adaptive gain scheduling-based control is introduced. As a conclusion, the final power quality is determined by a sum of various factors, and the thesis provides the guidelines for designing the system that improves the power quality experienced by the customer.

Eksotermiset kemialliset reaktiot ydinreaktoreissa

Neljännen sukupolven reaktoreissa käytetään uusia teknisiä ratkaisuja ja uudenlaisia materiaaleja, joten myös niiden turvallisuuskriteerien laatimiseen tarvitaan uusia näkökulmia. Tällä hetkellä kehitetäänkin teknologianeutraaleja turvallisuuskriteerejä, joista voitaisiin johtaa jokaiselle uudelle reaktorikonseptille reaktorin erityispiirteet huomioivat teknologiaspesifit turvallisuuskriteerit. Näin pystytään takaamaan turvallisuuden korkea taso kaikissa uusissa reaktoreissa. Eksotermiset eli lämpöä vapauttavat kemialliset reaktiot muodostavat merkittävän uhan ydinvoimalaitosten turvallisuudelle. Tutkimalla nykyisin käytössä olevia turvallisuuskriteerejä sekä kehitteillä olevia teknologianeutraaleja turvallisuuskriteerejä voitiin havaita, että eksotermiset kemialliset reaktiot on niissä huomioitu hyvin, mutta ei kovin systemaattisesti. Tämän tutkielman tavoitteena oli pohtia, kuinka eksotermiset kemialliset reaktiot voitaisiin huomioida systemaattisemmin teknologianeutraaleissa turvallisuuskriteereissä. Johtopäätöksenä on, että epätoivottujen eksotermisten kemiallisten reaktioiden tapahtuminen tulisi ensisijaisesti pyrkiä estämään, mutta jos tällainen reaktio kuitenkin tapahtuu, tulisi sen seurauksia lieventää. Eksotermisten kemiallisten reaktioiden tapahtuminen pystytään estämään, jos eksotermisesti reagoivia aineita ei ole tai ne pystytään pitämään erillään toisistaan, tai jos lämpötilat saadaan pidettyä riittävän alhaisina. Tutkielman toisena tavoitteena oli tarkastella onnettomuusskenaarioita, jotka voisivat johtaa eksotermisiin kemiallisiin reaktioihin erityisesti neljännen sukupolven reaktoreissa. Tätä varten tutkitaan kirjallisuuden avulla joidenkin reaktorimateriaalien kemiallisia ominaisuuksia sekä muutamia neljännen sukupolven reaktoreja. Kirjallisuuden avulla tarkastellaan myös muutamaa sellaista ydinvoimalaitosonnettomuutta, joissa eksotermiset kemialliset reaktiot ovat olleet merkittävässä roolissa.

Situational awareness concept in a multinational collaboration environment : challenges in the information sharing framework

Technological capabilities are built to support different types of collaboration, and this gives the justification to widely observe, how activity environments are influenced by technology. Technology as an enabler can be addressed from different perspectives, other than merely technological. Dynamic, evolving environment is at the same time interesting but also challenging. As a multinational collaboration environment, the maritime surveillance is an good example of time critical and evolving environment, where technological solutions enable new ways of collaboration. Justification for the inspiration to use maritime environment as the baseline for understanding the challenges in creating and maintaining adequate level of situational awareness, derives from the complexity of the collaboration and information sharing environment elements, needed to be taken into account, when analyzing criticalities related to decision making. Situational awareness is an important element supporting decision making, and challenges related to it can also be observed in the maritime environment. This dissertation describes the structures and factors involved in this complex setting, found from the case studies that should be taken into account when trying to understand, how these elements affect the activities. This dissertation focuses on the gray area that is between a life threatening situation and normal everyday activities. From the multinational experimentation series case studies, MNE5 and MNE6 it was possible to observe situations that were not life threatening for the participants themselves, but not also basic every day activities. These case studies provided a unique possibility to see situations, where gaining of situational awareness and decision making are challenged with time critical crisis situations. Unfortunately organizations do not normally take the benefit from the everyday work to prepare themselves for possible emerging crisis situations. This dissertation focuses on creating a conceptual model and a concept that supports organizations – also outside the maritime community – to improve their ability to support gaining of situational awareness from the individual training level, all the way to changes in organizational structures in aiming for better support for decision making from the individual level to the highest decision making level. Quick changes and unpredictability are reality in organizations and organizations do not have the possibility to control all the factors that affect their functioning. Since we cannot be prepared for everything, and predict every crisis, individual activities inside teams and as a part of organizations, need to be supported with guidance, tools and training in order to support acting in challenging situations. In fact the ideology of the conceptual model created, lies especially in the aim of not controlling everything in beforehand, but supporting organizations with concrete procedures to help individuals to react in different, unpredictable situations, instead of focusing on traditional risk prevention and management. Technological capabilities are not automatically solutions for functional challenges; this is why it is justified to broaden the problem area observation from the technological perspective. This dissertation demonstrates that it is possible to support collaboration in a multinational environment with technological solutions, but it requires the recognition of technological limitations and accepting the possible restrictions related to technological innovations. Technology should not be considered value per se, the value of technology should be defined according to the support of activities, including strategic and operational environment evaluation, identification of organizational elements, and taking into account also the social factors and their challenges. Then we are one step closer to providing technological solutions that support the actual activities by taking into account the variables of the activity environment in question. The multidisciplinary view to approach the information sharing and collaboration framework, is derived especially from the complexity of decision making and building of situational awareness, since they are not build or created in vacuity, but in the organizational framework by the people doing it with the technological capabilities, enabled by the organizational structures. Introduced case studies were related to maritime environment, but according to the research results, it is valid to argue, that based on the lessons learned it is possible to create and further develop conceptual model and to create a general concept to support a wider range of organizations in their attempt to gain better level of situational awareness (SA) and to support decision making. To proof the versatile usage of the developed concept, I have introduced the case study findings to the health care environment and reflected the identified elements from the trauma center to the created concept. The main contribution to complete this adventure is the presented situational awareness concept created in the respect to NATO concept structure. This has been done to tackle the challenge of collaboration by focusing on situational awareness in the information sharing context by providing a theoretical ground and understanding, of how these issues should be approached, and how these elements can be generalized and used to support activities in other environments as well. This dissertation research has been a several year evolving process reflecting and affecting presented case studies and this learning experience from the case studies has also affected the goals and research questions of this dissertation. This venture has been written from a retro perspective according to ideology of process modeling and design rationale to present to the reader how this entire journey took place and what where the critical milestones that affected the end result, conceptual model. Support in a challenging information sharing framework can be provided with the right type of combination of tools, procedures and individual effort. This dissertation will provide insights to those with a new approach to war technology for the organizations to gain a better level of awareness and to improve the capabilities in decision making. This dissertation will present, from the war technology starting point, a new approach and possibility for the organizations to create a better level of awareness and support for decision making with the right combination of tools, procedures and individual effort.

Electrical Machine Product Development; Transmission to Lean Approach

The requirements set by the market for electrical machines become increasingly demanding requiring more sophisticated technological solutions. Companies producing electrical ma-chines are challenged to develop machines that provide competitive edge for the customer for example through increased efficiency, reliability or some customer specific special requirement. The objective of this thesis is to derive a proposal for the first steps to transform the electrical machine product development process of a manufacturing company towards lean product development. The current product development process in the company is presented together with the processes of four other companies interviewed for the thesis. On the basis of current processes of the electrical machine industry and the related literature, a generalized electrical machine product development process is derived. The management isms and –tools utilized by the companies are analyzed. Adoption of lean Pull-Event –reviews, Oobeya –management and Knowledge based product development are suggested as the initial steps of implementing lean product development paradigm in the manufacturing company. Proposals for refining the cur-rent product development process and increasing the stakeholder involvement in the development projects are made. Lean product development is finding its way to Finnish electrical machine industry, but the results will be available only after the methods have been implemented and adopted by the companies. There is some enthusiasm about the benefits of lean approach and if executed successfully it will provide competitive edge for the Finnish electrical machine industry.

Analyse des stratégies d’évaluation des technologies des corps policiers canadiens : le cas de l’Identité Judiciaire

Les innovations technologiques pullulent dans le milieu policier depuis quelques années. Devant cette abondance de choix technologiques, et dans une conjoncture de ralentissement économique, la police doit s’assurer de faire une sélection favorisant le meilleur retour sur investissement. L’évaluation des technologies est la meilleure méthode permettant d’atteindre cet objectif. Ce projet de recherche analyse les différentes stratégies d’évaluation des technologies des corps policiers fédéraux et provinciaux du Canada en se basant sur le domaine baromètre de l’identité judiciaire. Cette étude s’appuie sur plusieurs données qualitatives : 1) observation participative à la Sûreté du Québec; 2) entrevues semi-directives (n=11) avec des membres de l’Ontario Provincial Police et de la Gendarmerie Royale du Canada. L’analyse intégrée des données colligées permet de mieux comprendre la dynamique de l’évaluation technologique dans la police. Même si une évolution est perceptible, certaines améliorations pourraient accroître l’efficacité du mini-PTA (Police Technology Assessment) dans un contexte où l’opérationnel et le théorique doivent cohabiter en parfaite harmonie afin de faciliter le travail des utilisateurs. Le mini-PTA est un outil facilitant l’adaptation de l’évaluation des technologies aux réalités régionales, mais ne peut en aucun cas remplacer unilatéralement le PTA fait par les grosses organisations d’évaluation des technologies policières.

Cyberjustice in Brazil : the use of technology to enhance access to justice and procedural celerity

Dans une société mondialisée, où les relations sont intégrées à une vitesse différente avec l'utilisation des technologies de l'information et des communications, l'accès à la justice gagne de nouveaux concepts, mais elle est encore confrontée à de vieux obstacles. La crise mondiale de l'accès à la justice dans le système judiciaire provoque des débats concernant l'égalité en vertu de la loi, la capacité des individus, la connaissance des droits, l'aide juridique, les coûts et les délais. Les deux derniers ont été les facteurs les plus importants du mécontentement des individus avec le système judiciaire. La présente étude a pour objet d'analyser l'incidence de l'utilisation de la technologie dans l’appareil judiciaire, avec l'accent sur la réalité brésilienne, la voie législative et des expériences antérieures dans le développement de logiciels de cyberjustice. La mise en œuvre de ces instruments innovants exige des investissements et de la planification, avec une attention particulière sur l'incidence qu'ils peuvent avoir sur les routines traditionnelles des tribunaux. De nouveaux défis sont sur la voie de ce processus de transformation et doivent être traités avec professionnalisme afin d'éviter l'échec de projets de qualité. En outre, si la technologie peut faire partie des différents aspects de notre quotidien et l'utilisation de modes alternatifs de résolution des conflits en ligne sont considérés comme un succès, pourquoi serait-il difficile de faire ce changement dans la prestation de la justice par le système judiciaire? Des solutions technologiques adoptées dans d'autres pays ne sont pas facilement transférables à un environnement culturel différent, mais il y a toujours la possibilité d'apprendre des expériences des autres et d’éviter de mauvaises voies qui pourraient compromettre la définition globale de l'accès à la justice.