NUMERICAL ANALYSIS OF A NOVEL 980nm MICROCAVITY SEMICONDUCTOR OPTICAL AMPLIFIER WITH HIGH GAIN AND LOW NOISE

A novel microcavity semiconductor optical amplifier ( MCSOA) was proposed by incorporating top and bottom distributed Bragg reflectors ( DBRs) into the waveguide structure of conventional traveling-wave semiconductor optical amplifiers(TW-SOAs). The incoming( outgoing) light beam incidented onto (escaped from) the waveguide structure at a oblique angle through two optical windows, where the top DBR was etched away, and anti-reflection coating was deposited. The light beams inside the optical cavity were reflected repeatedly between two DBRs and propagated along waveguide in a zigzag optical path. The performance of the MCSOA was systematically investigated by extensive numerical simulation based on a traveling-wave model by taking into account the comprehensive effects of DBRs on both the amplification of signals and the filtering of spontaneous emission( SE). Our results show that the MCSOA is capable of achieving a fiber-to-fiber gain as high as 40dB and a low noise figure is less than 3.5dB.

Monolithic integration of sampled grating DBR with electroabsorption modulator by combining selective-area-growth MOCVD and quantum-well intermixing

We present the monolithic integration of a sampled-grating distributed Bragg reflector (SC-DBR) laser with a quantum-well electroabsorption modulator (QW-EAM) by combining ultra-low-pressure (55 mbar) selective-area-growth (SAG) metal-organic chemical vapour deposition (MOCVD) and quantum-well intermixing (QWI) for the first time. The QW-EAM and the gain section can be grown simultaneously by using SAG MOCVD technology. Meanwhile, the QWI technology offers an abrupt band-gap change between two functional sections, which reduces internal absorption loss. The experimental results show that the threshold current I-th = 62 mA, and output power reaches 3.6 mW. The wavelength tuning range covers 30 nm, and all the corresponding side mode suppression ratios are over 30 dB. The extinction ratios at available wavelength channels can reach more than 14 dB with bias of -5 V.

Experimental study on a diode-pumped passively mode-locking Nd : GdVO4/SESAM laser

We demonstrate a low-threshold and efficient diode-pumped passively continuous wave (CW) mode-locked Nd:GdVO4 laser with a reflective semiconductor saturable absorber mirror (SESAM). The threshold for the continuous wave was 0.36 W, and it is the lowest threshold for a continuous wave in a passively mode-locked Nd:GdVO4 laser to our knowledge. The maximum average output power of 1.82 W was obtained at a pump power of 6.65 W with a slope efficiency of about 29%. The CW mode-locked pulse duration was measured to be about 10.5 ps with a 116-MHz repetition rate.

Narrow-Linewidth Microwave Generation Using a Self-Injected DBR Laser Diode

A novel technique for generating narrow-linewidth microwave or millimeter-wave signals is proposed. In this scheme, a delayed self-injected distributed Bragg reflector laser diode, which is tuned by a low-frequency square-wave voltage, is used to generate two correlated lightwaves simultaneously. Experiments show that the 10-dB linewidth of generated microwave signals is reduced from 147 MHz to 68 kHz utilizing the proposed self-injection technique.

Design and Fabrication of AlGaN-Based Resonant-Cavity-Enhanced p-i-n UV PDs

AlGaN-based resonant-cavity-enhanced (RCE) p-i-n photodetectors (PDs) for operating at the wavelength of 330 nm were designed and fabricated. A 20.5-pair AlN/Al0.3Ga0.7N distributed Bragg reflector (DBR) was used as the back mirror and a 3-pair AlN/Al0.3Ga0.7N DBR as the front one. In the cavity is a p-GaN/i-GaN/n-Al0.3Ga0.7N structure. The optical absorption of the RCE PD structure is at most 59.8% deduced from reflectance measurement. Selectively enhanced by the cavity effect, a response peak of 0.128 A/W at 330 nm with a half-peak breadth of 5.5 nm was obtained under zero bias. The peak wavelength shifted 15 nm with the incident angle of light increasing from 0 degrees to 60 degrees.

High responsivity resonant-cavity-enhanced InGaAs/GaAs quantum-dot photodetector for wavelength of similar to 1 mu m at room temperature

The characteristics of a resonant cavity-enhanced InGaAs/GaAs quantum-dot n-i-n photodiode with only a bottom distributed Bragg reflector used as the cavity mirror, are reported. To suppress the dark current, an AlAs layer is inserted into the device structure as the blocking layer. It turns out that the structure still possesses the resonant coupling nature, and makes Rabi splitting discernible in the photoluminescence spectra. The measured responsivity spectrum of the photocurrent shows a peak at lambda = 1030 nm, and increases rapidly as the bias voltage increases. A peak responsivity of 0.75 A/W, or equivalently an external quantum efficiency of 90.3%, is obtained at V-bias = -1.4 V.

Blue-violet Lasing of Optically Pumped GaN-Based Vertical Cavity Surface-Emitting Laser With Dielectric Distributed Bragg Reflectors

Optically pumped GaN-based vertical cavity surface-emitting laser (VCSEL) with two Ta2O5/SiO2 dielectric distributed Bragg reflectors (DBRs) was fabricated via a simplifled procedure direct deposition of the top DBR onto the GaN surface exposed after substrate removal and no use of etching and polishing processes. Blue-violet lasing action was observed at a wavelength of 397.3 ran under optical pumping at room temperature with a threshold pumping energy density of about 71.5 mJ/cm(2). The laser action was further confirmed by a narrow emission linewidth of 0.13 nm and a degree of polarization of about 65%. The result suggests that practical blue-violet GaN-bsaed VCSEL can be realized by optimizing the laser lift-off technique for substrate removal.

Electrically Driven InAs Quantum-Dot Single-Photon Sources

Electrically driven single photon source based on single InAs quantum dot (QDs) is demonstrated. The device contains InAs QDs within a planar cavity formed between a bottom AlGaAs/GaAs distributed Bragg reflector (DBR) and a surface GaAs-air interface. The device is characterized by I-V curve and electroluminescence, and a single sharp exciton emission line at 966nm is observed. Hanbury Brown and Twiss (HBT) correlation measurements demonstrate single photon emission with suppression of multiphoton emission to below 45% at 80K

Detailed model and investigation of gain saturation and carrier spatial hole burning for a semiconductor optical amplifier with gain clamping by a vertical laser field

A detailed model for semiconductor linear optical amplifiers (LOAs) with gain clamping by a vertical laser field is presented, which accounts the carrier and photon density distribution in the longitudinal direction as well as the facet reflectivity. The photon iterative method is used in the simulation with output amplified spontaneous emission spectrum in the wide band as iterative variables. The gain saturation behaviors and the noise figure are numerically simulated, and the variation of longitudinal carrier density with the input power is presented which is associated with the ON-OFF state of the vertical lasers. The results show that the LOA can have a gain spectrum clamped in a wide wavelength range and have almost the same value of noise figure as that of conventional semiconductor optical amplifiers (SOAs). Numerical results also show that an LOA can have a noise figure about 2 dB less than that of the SOA gain clamped by a distributed Bragg reflector laser.

Long-wavelength SiGe/Si MQW resonant-cavity-enhanced photodiodes (RCE-PD)

Si1-xGex/Si optoelectronic devices are promising for the monolithic integration with silicon-based microelectronics. SiGe/Si MQW RCE-PD (Resonant-Cavity-Enhanced photodiodes) with different structures were investigated in this work. Design and fabrication of top- and bottom-incident RCE-PD, such as growth of SiGe MQW (Multiple Quantum Wells) on Si and SOI (Si on insulator) wafers, bonding between SiGe epitaxial wafer and SOR (Surface Optical Reflector) consisting Of SiO2/Si DBR (Distributed Bragg Reflector) films on Si, and performances of RCE-PD, were presented. The responsivity of 44mA/W at 1.314 mum and the FWHM of 6nm were obtained at bias of 10V. The highest external quantum efficiency measured in the investigation is 4.2%.

Time dependence of wet oxidized AlGaAs/GaAs distributed Bragg reflectors

The time dependence of wet oxidized AlGaAs/GaAs in a distributed Bragg reflector (DBR) structure has been studied by mean of transmission electron microscopy and Raman spectroscopy. The wet oxidized AlGaAs transforms from an initial amorphous hydroxide phase to the polycrystalline gamma-Al2O3 phase with the extension of oxidation time. The thickness of oxide layers will contract due to the different volume per Al atom in AlGaAs and in the oxides. In the samples oxidized for 10 and 20 min, there are some fissures along the AlGaAs/GaAs interfaces. In the samples oxidized longer, although no such fissures are present along the interfaces, the whole oxidized DBR delaminates from the buffer. (c) 2005 American Vacuum Society.

A Si-based tunable narrow-band flat-top filter with multiple-step-type Fabry-Perot cavity structure

In the optical network, the quick and accurate alignment with wavelength is an important issue during the channel detection. At this point, a filter having flat-top response characteristic is an effective solution. Based on multiple-step-type Fabry-Perot cavity structure, a novel all-Si-based thermooptical tunable flat-top filter with narrow-band has been fabricated, using our patent silicon-on-reflector bonding technology. The device demonstrated a 1-dB flat-top width of 1 nm, 3-dB band of 3 nm, free spectra range of 8 nm, and the tuning range of 4.6 nm was obtained under the applied voltage of 4 V.

Interface of wet oxidized AlGaAs/GaAs distributed Bragg reflectors

The interface of wet oxidized Al0.97Ga0.03As/GaAs in a distributed Bragg reflector (DBR) structure has been studied by means of transmission electron microscopy and Raman spectroscopy. With the extension of oxidation time, the oxide/GaAs interfaces are not abrupt any more. There is an amorphous film near the oxide/GaAs interface, which is Ga2O3 related to the prolonged heating. In the samples oxidized for 10 and 20 min, there are some fissures along the oxidized AlGaAs/GaAs interfaces. In the samples oxidized or in situ annealed for long time, no such fissures are present due to the complete removal of the volatile products.

Diode-end-pumped passively CW mode-locked Nd : YLF laser by the LT-In0.25Ga0.75As absorber

We have demonstrated a self-staring passively continuous-wave mode-locked diode end-pumped Nd:YLF laser with a semiconductor saturable absorber mirror of single-quantum-well (In0.25Ga0.75As) grown by metal-organic chemical-vapor deposition technique at low temperature. The saturable absorber was used as nonlinear absorber and output coupler simultaneously. Stable pulse duration of 3 ps has been achieved at the repetition rate of 98 MHz. The average output power was 530 mW at 1053 nm under the incident pump power of 10 W, corresponding to the peak power of 1.8 kW and pulse energy of 5.4 nJ.

Improved optical heterodyne methods for measuring. frequency responses of photodetectors

An improved optical self-heterodyne method utilizing a distributed Bragg reflector (DBR) tunable laser and an optical fiber ring interferometer is presented in this paper. The interference efficiency can be increased by 7 dB compared with the scheme using the conventional Mach-Zehnder interferometer. The unsteady process that the beating frequency experiences in each tuning period is investigated. According to the measurement results, the wavelength and optical power of the tunable laser will be steady when the square-wave frequency is lower than 300 kHz. It has been shown that when a square-wave voltage is applied to the phase section of the tunable laser, the laser linewidths vary in a wide range, and are much larger than that under dc voltage tuning. The errors caused by the variations in the linewidth of the beat signal and optical power can be eliminated using the proposed calibration procedures, and the measurement accuracy can, therefore, be significantly improved. Experiments show that the frequency responses obtained using our method agree well with the data provided by the manufacturer, and the improved optical self-heterodyne method is as accurate as the intensity noise technique.