Influence of silvicultural regime on wood structure characteristics and mechanical properties of clear wood in Pinus sylvestris

Abstract

Spray coating technique asa surface treatment for woodcontaining paper grades

The objective of this work was to introduce the emerging non-contacting spray coating process and compare it to the existing coating techniques. Particular emphasis was given to the details of the spraying process of paper coating colour and the base paper requirements set by the new coating method. Spraying technology itself is nothing new, but the atomisation process of paper coating colour is quite unknown to the paper industry. The differences between the rheology of painting and coating colours make it very difficult to utilise the existing information from spray painting research. Based on the trials, some basic conclusion can be made:The results of this study suggest that the Brookfield viscosity of spray coating colour should be as low as possible, presently a 50 mPas level is regarded as an optimum. For the paper quality and coater runnability, the solids level should be as high as possible. However, the graininess of coated paper surface and the nozzle wear limits the maximum solids level to 60 % at the moment. Most likelydue to the low solids and low viscosity of the coating colour the low shear Brookfield viscosity correlates very well with the paper and spray fan qualities. High shear viscosity is also important, but yet less significant than the low shear viscosity. Droplet size should be minimized and besides keeping the brrokfield viscosity low that can be helped by using a surfactant or dispersing agent in the coating colour formula. Increasing the spraying pressure in the nozzle can also reduce the droplet size. The small droplet size also improves the coating coverage, since there is hardly any levelling taking place after the impact with the base paper. Because of the lack of shear forces after the application, the pigment particles do not orientate along the paper surface. Therefore the study indicates that based on the present know-how, no quality improvements can be obtained by the use of platy type of pigments. The other disadvantage of them is the rapid deterioration of the nozzle lifetime. Further research in both coating colour rheology and nozzle design may change this in the future, but so far only round shape pigments, like typically calcium carbonate is, can be used with spray coating. The low water retention characteristics of spray coating, enhanced by the low solids and low viscosity, challenge the base paper absorption properties.Filler level has to be low not to increase the number of small pores, which have a great influence on the absorption properties of the base paper. Hydrophobic sizing reduces this absorption and prevents binder migration efficiently. High surface roughness and especially poor formation of the base paper deteriorate thespray coated paper properties. However, pre-calendering of the base paper does not contribute anything to the finished paper quality, at least at the coating colour solids level below 60 %. When targeting a standard offset LWC grade, spraycoating produces similar quality to film coating, but yet blade coating being on a slightly better level. However, because of the savings in both investment and production costs, spray coating may have an excellent future ahead. The porousnature of the spray coated surface offers an optimum substrate for the coldset printing industry to utilise the potential of high quality papers in their business.

Structural and optical properties of InAs/GaAs quantum structures

The goal of the thesis was to study fundamental structural and optical properties of InAs islands and In(Ga)As quantum rings. The research was carried out at the Department of Micro and Nanosciences of Helsinki University of Technology. A good surface quality can be essential for the potential applications in optoelectronic devices. For such device applications it is usually necessary to control size, density and arrangement of the islands. In order to study the dependence of the structural properties of the islands and the quantum rings on growth conditions, atomic force microscope was used. Obtained results reveal that the size and the density of the In(Ga)As quantum rings strongly depend on the growth temperature, the annealing time and the thickness of the partial capping layer. From obtained results it is possible to conclude that to get round shape islands and high density one has to use growth temperature of 500 ̊C. In the case of formation of In(Ga)As quantum rings the effect of mobility anisotropy is observed that so the shape of the rings is not symmetric. To exclude this effect it is preferable to use a higher annealing temperature of 570 ̊C. Optical properties were characterized by PL spectroscopy. PL emission was observed from buried InAs quantum dots and In(Ga)As quantum rings grown with different annealing time and temperature and covered with a various thickness of the partial capping layer.

Validation of plant dynamic model by online and laboratory measurements – a tool to predict online COD loads out of production of mechanical printing papers

COD discharges out of processes have increased in line with elevating brightness demands for mechanical pulp and papers. The share of lignin-like substances in COD discharges is on average 75%. In this thesis, a plant dynamic model was created and validated as a means to predict COD loading and discharges out of a mill. The assays were carried out in one paper mill integrate producing mechanical printing papers. The objective in the modeling of plant dynamics was to predict day averages of COD load and discharges out of mills. This means that online data, like 1) the level of large storage towers of pulp and white water 2) pulp dosages, 3) production rates and 4) internal white water flows and discharges were used to create transients into the balances of solids and white water, referred to as “plant dynamics”. A conversion coefficient was verified between TOC and COD. The conversion coefficient was used for predicting the flows from TOC to COD to the waste water treatment plant. The COD load was modeled with similar uncertainty as in reference TOC sampling. The water balance of waste water treatment was validated by the reference concentration of COD. The difference of COD predictions against references was within the same deviation of TOC-predictions. The modeled yield losses and retention values of TOC in pulping and bleaching processes and the modeled fixing of colloidal TOC to solids between the pulping plant and the aeration basin in the waste water treatment plant were similar to references presented in literature. The valid water balances of the waste water treatment plant and the reduction model of lignin-like substances produced a valid prediction of COD discharges out of the mill. A 30% increase in the release of lignin-like substances in the form of production problems was observed in pulping and bleaching processes. The same increase was observed in COD discharges out of waste water treatment. In the prediction of annual COD discharge, it was noticed that the reduction of lignin has a wide deviation from year to year and from one mill to another. This made it difficult to compare the parameters of COD discharges validated in plant dynamic simulation with another mill producing mechanical printing papers. However, a trend of moving from unbleached towards high-brightness TMP in COD discharges was valid.

Structural studies on enzymes of biotechnological and biomedical interest

Structural studies of proteins aim at elucidating the atomic details of molecular interactions in biological processes of living organisms. These studies are particularly important in understanding structure, function and evolution of proteins and in defining their roles in complex biological settings. Furthermore, structural studies can be used for the development of novel properties in biomolecules of environmental, industrial and medical importance. X-ray crystallography is an invaluable tool to obtain accurate and precise information about the structure of proteins at the atomic level. Glutathione transferases (GSTs) are amongst the most versatile enzymes in nature. They are able to catalyze a wide variety of conjugation reactions between glutathione (GSH) and non-polar components containing an electrophilic carbon, nitrogen or sulphur atom. Plant GSTs from the Tau class (a poorly characterized class) play an important role in the detoxification of xenobiotics and stress tolerance. Structural studies were performed on a Tau class fluorodifen-inducible glutathione transferase from Glycine max (GmGSTU4-4) complexed with GSH (2.7 Å) and a product analogue Nb-GSH (1.7 Å). The three-dimensional structure of the GmGSTU4-4-GSH complex revealed that GSH binds in different conformations in the two subunits of the dimer: in an ionized form in one subunit and a non-ionized form in the second subunit. Only the ionized form of the substrate may lead to the formation of a catalytically competent complex. Structural comparison between the GSH and Nb-GSH bound complexes revealed significant differences with respect to the hydrogen-bonding, electrostatic interaction pattern, the upper part of -helix H4 and the C-terminus of the enzyme. These differences indicate an intrasubunit modulation between the G-and Hsites suggesting an induced-fit mechanism of xenobiotic substrate binding. A novel binding site on the surface of the enzyme was also revealed. Bacterial type-II L-asparaginases are used in the treatment of haematopoietic diseases such as acute lymphoblastic leukaemia (ALL) and lymphomas due to their ability to catalyze the conversion of L-asparagine to L-aspartate and ammonia. Escherichia coli and Erwinia chrysanthemi asparaginases are employed for the treatment of ALL for over 30 years. However, serious side-effects affecting the liver and pancreas have been observed due to the intrinsic glutaminase activity of the administered enzymes. Structural studies on Helicobacter pylori L-asparaginase (HpA) were carried out in an effort to discover novel L-asparaginases with potential chemotherapeutic utility in ALL treatment. Detailed analysis of the active site geometry revealed structurally significant differences between HpA and other Lasparaginases that may be important for the biological activities of the enzyme and could be further exploited in protein engineering efforts.

Combining Productivity and Renewal in a Production Organization: a Case Study on Organizational Ambidexterity

This case study examined how productivity and renewal are combined in a production organization operating in process industry through the antecedents of organizational ambidexterity; structure, culture, and management. The empirical material consisted of semi-structured interviews, observations and case organization documents. The findings suggest that the case organization structurally separates exploitation and exploration to separate units. However, it was found that the units focusing on exploration also devote resources to exploitation. External networks, such as customers, suppliers, and other factories seemed to play a role in the exploration activities, as well as in learning activities, which were connected to renewal. Productivity was seen as a natural part of a production organization and pursued at manufacturing units. Process management techniques appeared to be spread across the organization and having positive impact on exploitation and negative impact on exploration. The managerial culture and management’s capability to communicate goals, vision and strategy was found to be unsatisfactory. This thesis contributes to the new research paradigm of organizational ambidexterity by providing unique results on how the antecedents of organizational ambidexterity are accomplished in a production organization. Furthermore, the thesis extends the previous research of organizational renewal capability by connecting it to the ambidexterity theory.

Solids removal in pyrolysis

Pyrolysis is a process for turning biomass into liquid fuel. The process consists of heating the biomass in inert conditions and quenching the resulting vapors into oil. The oil has many potential uses, such as heating fuel in peak heating plants. In order to broaden the application base and improve the quality of the oil, solids removal has to be addressed. The solids may also increase the probability of plugging in downstream equipment. The purpose of this research was to gain an understanding of the formation of solids in the pyrolysis process and to assess options for reducing the solid content of the oil. From literature it is known that the solids can be removed either by hot vapor filtration, liquid treatment or multiple cyclones. Hot vapor filtration decreases yield, but improves the stability of the oil while simultaneously removing solids and ash. Liquid treatment techniques are good for removing large particles but involve losses of pyrolysis liquid. Cyclones are a traditional robust technique used regularly in pyrolysis. In the experimental part of this thesis, a 2 MWfuel pyrolysis setup with 2 cyclones in series was operated and monitored. Solid and liquid samples were collected from various parts of the process for further examination. Sampling and sample treatment techniques were developed. The chemical properties of the pyrolysis char were also analyzed and assessed as a function of reactor temperature and fluidizing velocity. By measuring the particle size distributions it was noticed that there were much smaller particles collected from the second cyclone than fed into pyrolysis. The solids in the pyrolysis oil were even smaller. This was most likely caused by attrition and shrinkage. Due to better separation efficiency of the cyclones in large particles, excess attrition should be avoided.

Aqueous-phase reforming of renewables for selective hydrogen production in the presence of supported platinum catalysts

The evolution of our society is impossible without a constant progress in life-important areas such as chemical engineering and technology. Innovation, creativity and technology are three main components driving the progress of chemistry further towards a sustainable society. Biomass, being an attractive renewable feedstock for production of fine chemicals, energy-rich materials and even transportation fuels, captures progressively new positions in the area of chemical technology. Knowledge of heterogeneous catalysis and chemical technology applied to transformation of biomass-derived substances will open doors for a sustainable economy and facilitates the discovery of novel environmentally-benign processes which probably will replace existing technologies in the era of biorefinary. Aqueous-phase reforming (APR) is regarded as a promising technology for production of hydrogen and liquids fuels from biomass-derived substances such as C3-C6 polyols. In the present work, aqueous-phase reforming of glycerol, xylitol and sorbitol was investigated in the presence of supported Pt catalysts. The catalysts were deposited on different support materials, including Al2O3, TiO2 and carbons. Catalytic measurements were performed in a laboratory-scale continuous fixedbed reactor. An advanced analytical approach was developed in order to identify reaction products and reaction intermediates in the APR of polyols. The influence of the substrate structure on the product formation and selectivity in the APR reaction was also investigated, showing that the yields of the desired products varied depending on the substrate chain length. Additionally, the influence of bioethanol additive in the APR of glycerol and sorbitol was studied. A reaction network was advanced explaining the formation of products and key intermediates. The structure sensitivity in the aqueous-phase reforming reaction was demonstrated using a series of platinum catalysts supported on carbon with different Pt cluster sizes in the continuous fixed-bed reactor. Furthermore, a correlation between texture physico-chemical properties of the catalysts and catalytic data was established. The effect of the second metal (Re, Cu) addition to Pt catalysts was investigated in the APR of xylitol showing a superior hydrocarbon formation on PtRe bimetallic catalysts compared to monometallic Pt. On the basis of the experimental data obtained, mathematical modeling of the reaction kinetics was performed. The developed model was proven to successfully describe experimental data on APR of sorbitol with good accuracy.

Bio and chemocatalysis for stereo and regioselective one-pot reaction applications

The development of cost efficient, selective and sustainable chemical processes for production of chiral building blocks is of great importance in synthetic and industrial organic chemistry. One way to reach these objectives is to carry out several reactions steps in one vessel at one time. Furthermore, when this kind of one-pot multi step reactions are catalyzed by heterogeneous chemo- and bio-catalysts, which can be separated from the reaction products by filtration, practical access to chiral small molecules for further utilization can be obtained. The initial reactions studied in this thesis are the two step dynamic kinetic resolution of rac-2-hydroxy-1-indanone and the regioselective hydrogenation of 1,2-indanedione. These reactions are then combined in a new heterogeneously catalyzed one-pot reaction sequence enabling simple recovery of the catalysts by filtration, facilitating simple reaction product isolation. Conclusively, the readily available 1,2-indanedione is by the presented one-pot sequence, utilizing heterogeneous enzyme and transition metal based catalysts, transferred with high regio- and stereoselectivity to a useful chiral vicinal hydroxyl ketone structure. Additional and complementary investigation of homogeneous half-sandwich ruthenium complexes for catalyzing the epimerization of chiral secondary alcohols of five natural products containing additional non-functionalized stereocenters was conducted. In principle, this kind of epimerization reactions of single stereocenters could be utilized for converting inexpensive starting materials, containing other stereogenic centers, into diastereomeric mixtures from which more valuable compounds can be isolated by traditional isolation techniques.

Mikrokanavareaktorin käyttö reaktorina eksotermisissä reaktioissa

Tämän työn kirjallisuusosassa on tarkasteltumikrokanavareaktoria teknisestä näkökulmasta. Kirjallisuusosassa käydään läpi mikrokanavareaktorin rakennetta, valmistajia sekä valmistusmenetelmiä. Toisena näkökulmana kirjallisuusosassa tarkastellaan mikrokanavareaktorin soveltuvuutta eksotermisiin reaktioihin. Eksotermisista reaktioista tarkasteluun valittiin FIscher-Tropsch synteesi, jota tarkastellaan tässä työssä tarkemmin. Lopuksi kirjallisuusosassa käsitellään mikrokanavareaktoritekniikkalla saavutettavia etuja sekä mikrokanavareaktoritekniikkaan liittyviä ongelmia. Soveltavassa osassa tarkasteltiin mikrokanavareaktorin soveltuvuutta Fischer-Tropsch synteesiin käyttäen apuna Aspen+ simulointiohjelmaa. Aspen+ simulointiohjelman avulla nähtiin mikrokanavareaktorin koon vaikutus Fischer-Tropsh synteesiin. Lisäksi soveltavassa osassa suunniteltiin simulointituloksiin sekä kirjallisuudesta saatuihin tietoihin perustuva teollisuuden mittakaavaan soveltuva mikrokanavareaktori. Lopuksi työssä pohdittiin mikrokanavareaktoritekniikkaa kirjallisuus sekä sekä soveltavan osan perusteella.

Paineellisten reaktoreiden projektitoimituksen optimointi

Diplomityössä tavoitteena on saada selvitys, jonka avulla yritys löytää toimitusprojekteistaan parannusta ja huomiota vaativat osa-alueet projektimuotoisten toimitusten kustannusrakennetta ja optimointia tarkastelemalla. Näin yritys voi tulevaisuudessa kehittää projektitoimituksen osa-alueita niin että se voi vastata asiakkaiden asettamiin vaatimuksiin sekä haasteisiin entistä nopeammin ja tarkemmin. Tutkimuksen lähtökohtana ovat projektiajattelu sekä siihen liittyvän toimitusketjun prosessit, joiden avulla lähestytään tutkimuksen ongelmaa ja selvitetään koko toimitusprojektin kehitystä vaativat alueet. Tutkimuksessa vaaditut tiedot saavutettiin vapaamuotoisten haastattelujen, yrityksen dokumentteja tutkimalla sekä yhteistyökumppanien avulla. Projektitoimituksen kokonaisvaltainen kehitys vaatii yhteistyötä ja huomiota toimitusketjun jokaisessa osa-alueessa aina raaka-ainelähteiltä loppukäyttäjälle asti. Näin voidaan saavuttaa tietojen avoimuus ja täsmällisyys, jotta päästään parhaaseen lopputulokseen projektitoimituksen osalta. Erityisesti kustannusrakenteen jakauma tuleehuomioida tulevaisuudessa tarkasti tehtäessä projektitoimitukseen liittyviä ratkaisuja. Esivalmistusasteen tarkastelu asetettiin työn alussa yhdeksi tärkeimmäksi tutkimuskohteeksi. Tarkastelussa havaittiin, että valmistusasteen valinnalla voidaan vaikuttaa lähes puoleen reaktorin kustannusrakenteen mukaisista kustannuksista kuten työ-, kuljetus- ja asennuskustannukseen. Myös materiaalikustannukset ovat suuressa roolissa reaktorinkustannusrakenteessa, joten tähän tulee kiinnittää myös huomiota. Muita tutkittavia tekijöitä, jotka pääasiassa vaikuttivat materiaali- ja asennuskustannuksiin työssä olivat paineastiastandardin ja paineluokan sekä valmistuspaikan valinta. Lisäksi huomioitiin toteutuneiden toimitusten eroavaisuuksia teoreettisiin ratkaisuihin ja etsittiin näistä mahdollisia kehitys- ja kustannussäästökohteita.

Prosessinostureita valmistavan liiketoimintayksikön arvoverkoston kustannusrakenne

Työn tarkoituksena on tutkia prosessinosturiliiketoiminnan rajatun arvoketjun ja - verkoston kustannuksia. Tavoitteena on selvittää valittujen vaihtoehtoisten valmistuspaikkojen toimintojen pohjalta yleinen arvoketju kustannuskertymineen. Lisäksi tavoitteena on kehittää taulukkolaskentaohjelmistoon perustuva laskentamalli tai perustyökalu kustannusten kasautumisen arviointiin. Edelleen pyrkimyksenä on löytää rakennetusta mallin avulla kehitys- ja jatkotoimenpiteiden kohteita. Työssä perehdytään aluksi arvoketju -viitekehykseen ja niihin seikkoihin joista se muodostuu kirjallisuudesta löytyvän tiedon pohjalta. Arvoketjuajattelu on yksinkertaisimmillaan yrityksen toimintojen tarkastelua kilpailukyvyn ja -edun näkökulmasta. Liiketoiminnan kehittyminen verkostomaiseksi vaatii kuitenkin laajemman ¿ arvoverkosto - tarkastelunäkökulman. Toisaalta liiketoiminnan pidemmän aikavälin kilpailukyvyn suunnittelu edellyttää syvällisempää arvoketjujen ja toimintojen tarkastelua ja hallintaa, jolloin tarvitaan kehittyneempiä laskentatoimen menetelmiä ja kustannuslaskentajärjestelmiä. Tutkimuksen empiirisessä osiossa arvoketjuajattelua ja arvoverkostoviitekehystä sekä kustannuslaskentamenetelmiä sovelletaan käytännön tapauksiin. Tulokset osoittavat tutkimukseen valittujen neljän valmistuspaikan kustannuskertymän ja -rakenteen. Kustannuskertymältään alhaisimmaksi osoittautui tuotantolaitos Saudi-Arabiassa, kunloppuasiakkaan sijainti on Qatarissa. Puolalainen tehdas osoittautui puolestaankilpailukykyisimmäksi, kun nosturin toimitusosoite on Italian pohjoisosaan. Tulosten perusteella kustannusrakenteiden suurimmat kustannuserät ovat kuljetus-, teräsrakenteen valmistus- ja suunnittelutoiminnot.

Henkilöstöraportointi - tunnuslukujen valinta ja seuraaminen henkilöstöstrategian toteuttamisessa, case: UPM-Kymmene Oyj, Voikkaa

Tutkimusalueena on henkilöstöraportointi ja henkilöstötilinpäätöksen tekeminen. Tavoitteena on selvittää henkilöstöraportoinnin tekemisestä saatava taloudellinen hyöty yritykselle. Teoriaosuudessa olen käyttänyt deskriptiivistä tutkimusmenetelmää ja empiriaosuudessa normatiivista. Empiriaosuus on rajattu UPM-Kymmene Oyj:n Voikkaan paperitehtaaseen. Case-organisaatiolle valitaan henkilöstötunnusluvut ja kehitetään sille sopiva henkilöstötunnuslukujen seurannan malli. Tunnusluvut ovat työkaluna analysoitaessa henkilöstön tämän hetkistä rakennetta, laatua ja työhyvinvointia. Pitkän aikavälin tuloksen tekemisessä henkilöstön osaamisella, työkyvyllä ja työmotivaatiolla on suuri merkitys. Osaamisen kehittymistä ja työhyvinvointia on seurattava kyselyillä. Brändilupausten, kuten esim. laadun ja osaamisen kehittämisen seurannassa voidaan myös hyödyntää henkilöstöraportoinnin tuottamia tunnuslukuja. Henkilöstöraportointi tuottaa informaatiota eri sidosryhmille: omistajat, sijoittajat, henkilöstö, asiakkaat, pankit, analyytikot ja toimittajat.

Kuitujen kiharuuteen vaikuttavia tekijöitä sulfaattiselluloosan valmistuksessa

Diplomityön tarkoituksena oli selvittää kuitujen kihartuvuuden profiili koivu- ja havusellulinjalla prosessivaiheiden suhteen. Profiilin perusteella pyrittiin selvittämään kuitulinjojen prosessista kuitujen kiharuuteen voimakkaimmin vaikuttavia tekijöitä. Työn kirjallisuusosassa käsiteltiin kuitujen ominaisuuksia sekä teollisen sellun valmistusprosessin kuituihin aiheuttamia kuituvaurioita ja niiden mahdollisia syitä. Lisäksi käytiin läpi kuituvaurioiden analysointimenetelmiä ja kuituvaurioiden kanssa korreloivia sellun laatuarvoja. Työn kokeellinen osa suoritettiin kuitulinjojen normaalin tuotannon ohessa. Kokeellisen osan massanäytteitä otettiin varsin moninaisista tuotantotilanteista mahdollisimman kattavan kiharuusprofiilin aikaansaamiseksi. Koivusellulinjalla vuokeittimen tuotantotaso vaikutti suuresti valmistettavan sellun ominaisuuksiin. Kuituvaurioiden syntyyn voimakkaimmin vaikuttavaksi tekijäksi osoittautui keittimen pohja-alueen, puskun ja massan pesuvaiheen sakeus. Tämän alueen sakeus muuttui tuotantotason mukaan, tuotantotason kasvun myötä alueen sakeus laski. Sakeuden lasku vähensi kuitujen kiharuutta sekä massan venymää ja paransi vetojäykkyyttä. Tuotantotason kasvu paransi myös keittimestä otettujen massanäytteiden vetojäykkyyspotentiaalia. Havusellulinjalla käytetyn Lo-Solids –keittomallin ja konventionaalisen keittomallin kesken esiintyi varsin merkittäviä laadullisia eroja. Lo-Solids –keittomallilla keitetyt sellukuidut kihartuivat konventionaalisella keittomallilla keitettyjä sellukuituja enemmän. Lo-Solids –keittomallilla keitetyn sellun vetojäykkyys oli konventionaalisella mallilla keitetyn sellun vetojäykkyyttä heikompi.

Hitsauksen laadunvarmistus teräsrakentamisessa

Suomessa on tapahtunut 2000-luvulla neljä kappaletta ns. suuronnettomuuden vaaratilanteiksi luokiteltavaa teräsrakenteiden vaurioitumisesta aiheutunutta onnettomuutta, joista yksi johti ihmishengen menetykseen. Onnettomuuden syynä oli huonolaatuisten pienahitsien pettäminen kuormituksen alaisena, joka puolestaan oli seurausta puutteellisesta hitsauksen laadunvarmistuksesta. Teräsrakenteiden valmistus ja hitsaus eivät ole yhtä tarkan viranomaisvalvonnan alaista kuten esimerkiksi painelaitteiden valmistus, vaikka teräsrakenteiden vaurioitumisesta aiheutuvat riskit ovat erittäin merkittäviä. Työn tavoitteena oli tutustua onnettomuustapauksiin, teräsrakenteista annettuihin viranomaismääräyksiin sekä ohjeisiin ja esittää laadunvarmistustoimenpiteitä, joiden avulla voidaan varmistua hitsaustyön riittävästä laadusta teräsrakentamisessa. Näitä laadunvarmistustoimenpiteitä ovat mm. hitsaushenkilöstön pätevöinti, hitsausohjeiden käyttäminen, ainetta rikkomattomat tarkastukset ja rakennesuunnitelmien tarkastukset. Toisena tavoitteena oli kartoittaa rakenteiden valmistajien ja pääurakoitsijoiden nykyistä tilannetta laadunvarmistuksen osalta sekä selvittää kiinnostusta kolmannen osapuolen tarjoamiin laadunvarmistuspalveluihin. Kyselyiden perusteella laadunvarmistuspalveluille on olemassa kysyntää tietyin kustannuksiin liittyvin varauksin. Palveluista eniten kiinnostusta herättivät ainetta rikkomattomat tarkastukset ja rakennesuunnitelmien tarkastukset.