Do Open Access journals qualify?

Presentation at the Nordic Perspectives on Open Access and Open Science seminar, Helsinki, October 15, 2013

Improving quality at the preanalytical phase of blood sampling : literature review

Julkaisumaa: 158 TW TWN Taiwan

Laser Cutting of Austenitic Stainless Steel with a High Quality Laser Beam

The thin disk and fiber lasers are new solid-state laser technologies that offer a combinationof high beam quality and a wavelength that is easily absorbed by metal surfacesand are expected to challenge the CO2 and Nd:YAG lasers in cutting of metals ofthick sections (thickness greater than 2mm). This thesis studied the potential of the disk and fiber lasers for cutting applications and the benefits of their better beam quality. The literature review covered the principles of the disk laser, high power fiber laser, CO2 laser and Nd:YAG laser as well as the principle of laser cutting. The cutting experiments were made with thedisk, fiber and CO2 lasers using nitrogen as an assist gas. The test material was austenitic stainless steel of sheet thickness 1.3mm, 2.3mm, 4.3mm and 6.2mm for the disk and fiber laser cutting experiments and sheet thickness of 1.3mm, 1.85mm, 4.4mm and 6.4mm for the CO2 laser cutting experiments. The experiments focused on the maximum cutting speeds with appropriate cut quality. Kerf width, cutedge perpendicularity and surface roughness were the cut characteristics used to analyze the cut quality. Attempts were made to draw conclusions on the influence of high beam quality on the cutting speed and cut quality. The cutting speeds were enormous for the disk and fiber laser cutting experiments with the 1.3mm and 2.3mm sheet thickness and the cut quality was good. The disk and fiber laser cutting speeds were lower at 4.3mm and 6.2mm sheet thickness but there was still a considerable percentage increase in cutting speeds compared to the CO2 laser cutting speeds at similar sheet thickness. However, the cut quality for 6.2mm thickness was not very good for the disk and fiber laser cutting experiments but could probably be improved by proper selection of cutting parameters.

New Product Development (NPD) Success Factors: A Review of the Literature

This paper reviews the literature on managerially actionable new product development success factors and summarises the field in a classic managerial framework. Because of the varying quality, breadth and scope of the field, the review only contains post-1980 studies of tangible product development that are of a rigorous scientific standard. Success is interpreted as a commercial success. The field has gained insight into a broad set of factors that vary in scope, abstraction and context. Main areas that contribute to NPD success are top management support exhibited through resource allocation and communicating the strategic importance of NPD in the organisation. The right projects need to be selected for investment at the beginning of the process and should be aligned to the organisation's internal competencies and the external environment. The NPD process should use cross-functional teams and a competent project champions. Marketing research competency is crucial, as an understanding of the market, customers and competitors is repeatedly highlighted. Product launch competency was also consistently shown to be important. In terms of controlling the NPD process, strict project gates are required to maintain control.

Quality and analysis of administration processes in server operations

IT outsourcing refers to the way companies focus on their core competencies and buy the supporting functions from other companies specialized in that area. Service is the total outcome of numerous of activities by employees and other resources to provide solutions to customers' problems. Outsourcing and service business have their unique characteristics. Service Level Agreements quantify the minimum acceptable service to the user. The service quality has to be objectively quantified so that its achievement or non-achievement of it can be monitored. Usually offshoring refers to the transferring of tasks to low-cost nations. Offshoring presents a lot of challenges that require special attention and they need to be assessed thoroughly. IT Infrastructure management refers to installation and basic usability assistance of operating systems, network and server tools and utilities. ITIL defines the industry best practices for organizing IT processes. This thesis did an analysis of server operations service and the customers’ perception of the quality of daily operations. The agreed workflows and processes should be followed better. Service providers’ processes are thoroughly defined but both the customer and the service provider might disobey them. Service provider should review the workflows regarding customer functions. Customer facing functions require persistent skill development, as they communicate the quality to the customer. Service provider needs to provide better organized communication and knowledge exchange methods between the specialists in different geographical locations.

Measuring Cost of Poor Quality in Industrial Electronics

Quality is not only free but it can be a profit maker. Every dollar that is not spent on doing things wrong becomes a dollar right on the bottom line. The main objective of this thesis is to give an answer on how cost of poor quality can be measured theoretically correctly. Different calculation methods for cost of poor quality are presented and discussed in order to give comprehensive picture about measurement process. The second objective is to utilize the knowledge from the literature review and to apply it when creating a method for measuring cost of poor quality in supplier performance rating. Literature review indicates that P-A-F model together with ABC methodology provides a mean for quality cost calculations. These models give an answer what should be measured and how this measurement should be carried out. However, when product or service quality costs are incurred when quality character derivates from target value, then QLF seems to be most appropriate methodology for quality cost calculation. These methodologies were applied when creating a quality cost calculation method for supplier performance ratings.

The Impact of Service Quality and Relationship Quality on Customer Loyalty in Business-to-Business Context

The main objective of this Master’s Thesis was to examine the interrelations of service quality and relationship quality (customer satisfaction, trust and commitment), and find out are they antecedents for customer loyalty in business-to-business context. Literature review revealed some research gaps concerning these focal concepts, which should be studied more closely. The theoretical basis for this research was collected for evaluating a strategic increase of customer’s perceptions of service quality and relationship quality as well as customer loyalty in business-to-business environment, and it was tested empirically in a sample of 164 corporate customers, who responded to the Internet-based survey. The measures, used in the survey, were first assessed by using confirmatory factor analysis (CFA), and then the hypothesized relationships were further verified using structural equation modeling (SEM) in LISREL 8.80. There was found support for a half of the hypothesized construct relations. The results of the research confirm the direct influence of trust and commitment on customer loyalty. Also, service quality turned out to have an indirect impact on customer loyalty through trust. No support, however, was offered for the proposed impact of customer satisfaction on loyalty in this case. The research provides managerially relevant and actionable results that may help service providers execute more specific customer relationship quality strategies that lead to higher customer loyalty.

Coercion, Perceived Care and Quality of Life Among Patients in Psychiatric Hospitals

The goals of the study were to describe patients’ perceptions of care after experiencing seclusion/restraint and their quality of life. The goal was moreover to identify methodological challenges related to studies from the perspective of coerced patients. The study was conducted in three phases between September 2008 and April 2012. In the first phase, the instrument Secluded/ Restrained Patients’ Perception of their Treatment (SR-PPT) was developed and validated in Japan in cooperation with a Finnish research group (n = 56). Additional data were collected over one year from secluded/restrained patients using the instrument (n = 90). In the second phase, data were collected during the discharge process (n = 264). In the third phase, data were collected from electronic databases. Methodological and ethical issues were reviewed (n = 32) using systematic review method. Patients perceived that co-operation with the staff was poor; patients’ opinions were not taken into account, treatment targets collated and treatment methods were seen in different ways. Patients also felt that their concerns were not well enough understood. However, patients received getting nurses’ time. In particular, seclusion/restraint was considered unnecessary. The patients felt that they benefited from the isolation in treating their problems more than they needed it, even if the benefit was seen to be minor. Patients treated on forensic wards rated their treatment and care significantly lower than in general units. During hospitalization secluded/restrained patients evaluated their quality of life, however, better than did non-secluded/restrained patients. However, no conclusion is drawn to the effect that the better quality of life assessment is attributable to the seclusion/restraint because patients’ treatment period after the isolation was long and because of many other factors, as rehabilitation, medication, diagnostic differences, and adaptation. According to the systematic mixed studies review variation between study designs was found to be a methodological challenge. This makes comparison of the results more difficult. A research ethical weakness is conceded as regards descriptions of the ethical review process (44 %) and informed consent (32 %). It can be concluded that patients in psychiatric hospital care and having a voice as an equal expert require special attention to clinical nursing, decision-making and service planning. Patients and their family members will be consulted in plans of preventive and alternative methods for seclusion and restraint. The study supports the theory that in ethical decision-making situations account should be taken of medical indications, in addition to the patients’ preferences, the effect of treatment on quality of life, and this depends on other factors. The connection between treatment decisions and a patient’s quality of life should be evaluated more structurally in practice. Changing treatment culture towards patients’ involvement will support daily life in nursing and service planning taking into account improvements in patients’ quality of life.

Asleep or not asleep? Evaluation of the Quality of Patients’ Sleep in Critical Care Nursing

Sleep is important for the recovery of a critically ill patient, as lack of sleep is known to influence negatively a person’s cardiovascular system, mood, orientation, and metabolic and immune function and thus, it may prolong patients’ intensive care unit (ICU) and hospital stay. Intubated and mechanically ventilated patients suffer from fragmented and light sleep. However, it is not known well how non-intubated patients sleep. The evaluation of the patients’ sleep may be compromised by their fatigue and still position with no indication if they are asleep or not. The purpose of this study was to evaluate ICU patients’ sleep evaluation methods, the quality of non-intubated patients’ sleep, and the sleep evaluations performed by ICU nurses. The aims were to develop recommendations of patients’ sleep evaluation for ICU nurses and to provide a description of the quality of non-intubated patients’ sleep. The literature review of ICU patients’ sleep evaluation methods was extended to the end of 2014. The evaluation of the quality of patients’ sleep was conducted with four data: A) the nurses’ narrative documentations of the quality of patients’ sleep (n=114), B) the nurses’ sleep evaluations (n=21) with a structured observation instrument C) the patients’ self-evaluations (n=114) with the Richards-Campbell Sleep Questionnaire, and D) polysomnographic evaluations of the quality of patients’ sleep (n=21). The correspondence of data A with data C (collected 4–8/2011), and data B with data D (collected 5–8/2009) were analysed. Content analysis was used for the nurses’ documentations and statistical analyses for all the other data. The quality of non-intubated patients’ sleep varied between individuals. In many patients, sleep was light, awakenings were frequent, and the amount of sleep was insufficient as compared to sleep in healthy people. However, some patients were able to sleep well. The patients evaluated the quality of their sleep on average neither high nor low. Sleep depth was evaluated to be the worst and the speed of falling asleep the best aspect of sleep, on a scale 0 (poor sleep) to 100 (good sleep). Nursing care was mostly performed while the patients were awake, and thus the disturbing effect was low. The instruments available for nurses to evaluate the quality of patients’ sleep were limited and measured mainly the quantity of sleep. Nurses’ structured observatory evaluations of the quality of patients’ sleep were correct for approximately two thirds of the cases, and only regarding total sleep time. Nurses’ narrative documentations of the patients’ sleep corresponded with patients’ self-evaluations in just over half of the cases. However, nurses documented several dimensions of sleep that are not included in the present sleep evaluation instruments. They could be classified according to the components of the nursing process: needs assessment, sleep assessment, intervention, and effect of intervention. Valid, more comprehensive sleep evaluation methods for nurses are needed to evaluate, document, improve and study patients’ quality of sleep.

Dynamic Competitor Analysis Model Of Welding Quality Management Software

Tämä diplomityö arvioi hitsauksen laadunhallintaohjelmistomarkkinoiden kilpailijoita. Kilpailukenttä on uusi ja ei ole tarkkaa tietoa siitä minkälaisia kilpailijoita on markkinoilla. Hitsauksen laadunhallintaohjelmisto auttaa yrityksiä takaamaan korkean laadun. Ohjelmisto takaa korkean laadun varmistamalla, että hitsaaja on pätevä, hän noudattaa hitsausohjeita ja annettuja parametreja. Sen lisäksi ohjelmisto kerää kaiken tiedon hitsausprosessista ja luo siitä vaadittavat dokumentit. Diplomityön teoriaosuus muodostuu kirjallisuuskatsauksesta ratkaisuliike-toimintaan, kilpailija-analyysin ja kilpailuvoimien teoriaan sekä hitsauksen laadunhallintaan. Työn empiriaosuus on laadullinen tutkimus, jossa tutkitaan kilpailevia hitsauksen laadunhallintaohjelmistoja ja haastatellaan ohjelmistojen käyttäjiä. Diplomityön tuloksena saadaan uusi kilpailija-analyysimalli hitsauksen laadunhallintaohjelmistoille. Mallin avulla voidaan arvostella ohjelmistot niiden tarjoamien primääri- ja sekundääriominaisuuksien perusteella. Toiseksi tässä diplomityössä analysoidaan nykyinen kilpailijatilanne hyödyntämällä juuri kehitettyä kilpailija-analyysimallia.

Production Quality Analysis of Special Elevator Cars Based on Six Sigma Approach

Project scope is to utilize Six Sigma DMAIC approach and lean principles to improve production quality of the case company. Six Sigma tools and techniques are explored through a literature review and later used in the quality control phase. The focus is set on the Pareto analysis to demonstrate the most evident development areas in the production. Materials that are not delivered to the customer or materials that damaged during transportation comprise the biggest share of all feedbacks. The goal is set to reduce these feedbacks by 50 %. Production observation pointed out that not only material shortages but also over-production is a daily situation. As a result, an initial picking list where the purchased and own production components can be seen, is created, reduction of over- and underproduction and material marking improvement are seen the most competitive options so that the goal can be reached. The picking list development should still continue to make sure that the list can be used not only in the case study but also in the industrial scale. The reduction of material missing category can be evaluated reliably not sooner than in few years because it takes time to gather the needed statistical information.

Development of a New Welding Product Quality Control and Management System Model for China

The Chinese welding industry is growing every year due to rapid development of the Chinese economy. Increasingly, companies around the world are looking to use Chinese enterprises as their cooperation partners. However, the Chinese welding industry also has its weaknesses, such as relatively low quality and weak management. A modern, advanced welding management system appropriate for local socio-economic conditions is required to enable Chinese enterprises to enhance further their business development. The thesis researches the design and implementation of a new welding quality management system for China. This new system is called ‗welding production quality control management model in China‘ (WQMC). Constructed on the basis of analysis of a survey and in-company interviews, the welding management system comprises the following different elements and perspectives: a ‗Localized congenital existing problem resolution strategies‘ (LCEPRS) database, a ‗human factor designed training system‘ (HFDT) training strategy, the theory of modular design, ISO 3834 requirements, total welding management (TWM), and lean manufacturing (LEAN) theory. The methods used in the research are literature review, questionnaires, interviews, and the author‘s model design experiences and observations, i.e. the approach is primarily qualitative and phenomenological. The thesis describes the design and implementation of a HFDT strategy in Chinese welding companies. Such training is an effective way to increase employees‘ awareness of quality and issues associated with quality assurance. The study identified widely existing problems in the Chinese welding industry and constructed a LCEPRS database that can be used in efforts to mitigate and avoid common problems. The work uses the theory of modular design, TWM and LEAN as tools for the implementation of the WQMC system.