Electrical characteristics of eddy current position sensor

In the thesis the principle of work of eddy current position sensors and the main cautions that must be taken into account while sensor design process are explained. A way of automated eddy current position sensor electrical characteristics measurement is suggested. A prototype of the eddy current position sensor and its electrical characteristics are investigated. The results obtained by means of the automated measuring system are explained.

DFM(A)- aspects for a microwave waveguide ring resonator design

In this research manufacturability analysis is made for an E-plane waveguide ring resonator. About the electrical characteristics of the waveguide ring resonator is discussed. Possibilities to utilize concurrent engineering method both for designing and making manufacturability analysis for MW- and RF-components are discussed. For helping to establish the necessary guidelines for easy manufacturing and assembly of the waveguide ring resonator a specialised DFM(A)-questionnaire is generated. The questionnaire gives also new information for collaborative designing approach in MW-/RF- engineering. The advantages and disadvantages of the concurrent engineering design method are evaluated in the research.

3D Stripixel Detectors Simulation

Solid-state silicon detectors have replaced conventional ones in almost all recent high-energy physics experiments. Pixel silicon sensors don't have any alternative in the area near the interaction point because of their high resolution and fast operation speed. However, present detectors hardly withstand high radiation doses. Forthcoming upgrade of the LHC in 2014 requires development of a new generation of pixel detectors which will be able to operate under ten times increased luminosity. A planar fabrication technique has some physical limitations; an improvement of the radiation hardness will reduce sensitivity of a detector. In that case a 3D pixel detector seems to be the most promising device which can overcome these difficulties. The objective of this work was to model a structure of the 3D stripixel detector and to simulate electrical characteristics of the device. Silvaco Atlas software has been used for these purposes. The structures of single and double sided dual column detectors with active edges were described using special command language. Simulations of these detectors have shown that electric field inside an active area has more uniform distribution in comparison to the planar structure. A smaller interelectrode space leads to a stronger field and also decreases the collection time. This makes the new type of detectors more radiation resistant. Other discovered advantages are the lower full depletion voltage and increased charge collection efficiency. So the 3D stripixel detectors have demonstrated improved characteristics and will be a suitable replacement for the planar ones.

Simulation of new p-type pixel strip detector with enhanced multiplication effect

This Master’s Thesis is dedicated to the simulation of new p-type pixel strip detector with enhanced multiplication effect. It is done for high-energy physics experiments upgrade such as Super Large Hadron Collider especially for Compact Muon Solenoid particle track silicon detectors. These detectors are used in very harsh radiation environment and should have good radiation hardness. The device engineering technology for developing more radiation hard particle detectors is used for minimizing the radiation degradation. New detector structure with enhanced multiplication effect is proposed in this work. There are studies of electric field and electric charge distribution of conventional and new p-type detector under reverse voltage bias and irradiation. Finally, the dependence of the anode current from the applied cathode reverse voltage bias under irradiation is obtained in this Thesis. For simulation Silvaco Technology Computer Aided Design software was used. Athena was used for creation of doping profiles and device structures and Atlas was used for getting electrical characteristics of the studied devices. The program codes for this software are represented in Appendixes.

Case: Kitaravahvistimen AB-luokan tehovahvistimen päivittäminen D-luokkaan

D-luokan vahvistimien etu perinteisiin A- tai AB-luokan vahvistimiin nähden on niitten korkea hyötysuhde ja pieni koko. Lisäksi ne ovat edullisia ja niihin voidaan asentaa pienemmät jäähdytyslevyt kuin perinteisiin vahvistimiin korkean hyötysuhteen ansiosta. Tässä tutkimuksessa asennetaan Peavey Solo –kitaravahvistimen pääteasteena toimivan AB-luokan päätevahvistimen tilalle tehokkaampi ja uudempaa vahvistinluokkaa edustava D-luokan vahvistin. Tutkimuksessa selvitetään, miten D-luokan vahvistimella toteutettu kytkentä toimii verrattuna alkuperäiseen kytkentään tutkimalla kitaravahvistimelle tyypillisiä sähköisiä ominaisuuksia. Työ toteutetaan mittauksin. Koska työssä olevissa kytkennöissä on jännitteisiä osia, on siinä perehdyttävä sähköturvallisuuteen. D-luokan vahvistin asettaa tietyt sähkötekniset kestävyysvaatimukset kytkennän teholähteelle ja kaiutinelementille, jolloin työssä paneudutaan myös niiden valintaan. D-luokan vahvistimeen päivitetyn kytkennän tuottamat äänenpainetasot olivat valtaosassa mittauksia suuremmat kuin alkuperäisellä kytkennällä. Äänenpainetasojen mittaustilanteissa myös kuormalle syötetyt tehot olivat suuremmat päivitetyllä kytkennällä verrattuna alkuperäiseen. Suurin päivitetyn kytkennän kuorman teho 72,72 W saavutettiin, kun kaiutinelementin yli oli 24,12 V:n jännitteen tehollisarvo ja kuorman teho oli noin 36 kertaa suurempi kuin alkuperäisellä kytkennällä. D-luokan vahvistimen mitatut harmonisen särön arvot ovat huomattavasti pienempiä kuin alkuperäisellä vahvistimella. Muokkaamattoman vahvistimen mitatusta sähköisestä taajuusvasteeesta nähdään, että alkuperäinen vahvistin korostaa tiettyjä taajuuksia, kun D-luokan vahvistimen taajuusvaste on sen sijaan likimain tasainen. Akustinen taajuusvaste ei ole niin tasainen D-luokan vahvistimeen päivitetyllä kytkennällä kuin alkuperäisellä kytkennällä ja sillä on myös kapeampi taajuusalue. Jos päivitetyn kytkennän sointia haluttaisiin parantaa, pitäisi tutkia lisää akustiseen taajuusvasteeseen vaikuttavia asioita.

Electrical Machines' Market in Russia

Venäjän valtion osuus maailmantaloudesta on pieni verrattuna sen maantieteelliseen kokoon, väkilukuun ja luonnonvaroihin. Sitä pidetään kuitenkin yhtenä tulevaisuuden merkittävistä kasvumarkkinoista. Venäjällä on tyypillisesti teollisuutta, joka hyödyntää luonnonvaroja ja tuottaa raaka-aineita sekä kotimaan että ulkomaiden markkinoille. Tällaisia tyypillisiä teollisuudenaloja Venäjällä ovat kaivos- ja metsäteollisuus sekä kemikaalien- kaasun- ja öljyntuotanto. Myös näiden teollisuusalojen tarvitsemien tuotantolaitteiden ja koneiden valmistusta on Venäjällä. Näitä koneita viedään Venäjältä entisiin neuvostovaltioihin ja päinvastoin. Tässä diplomityössä tutkitaan sähkömoottorien markkinapotentiaalia ja kilpailutilannetta Venäjällä. Venäjän osalta perehdytään sen kansantalouden tilaan ja tutkitaan sähkökonemarkkinoiden kokoa segmenteittäin monien erilähteiden avulla. Venäjän arvioidaan olevan erittäin potentiaalinen ja kasvava markkina-alue. Diplomityössä selvitetään ostoprosessia Venäjällä ja sähkökonemarkkinoiden ominaisuuksia kyseisellä alueella.

Applicability of Power-Line Communications to Data Transfer of On-line Condition Monitoring of Electrical Drives

The research of power-line communications has been concentrated on home automation, broadband indoor communications and broadband data transfer in a low voltage distribution network between home andtransformer station. There has not been carried out much research work that is focused on the high frequency characteristics of industrial low voltage distribution networks. The industrial low voltage distribution network may be utilised as a communication channel to data transfer required by the on-line condition monitoring of electric motors. The advantage of using power-line data transfer is that it does not require the installing of new cables. In the first part of this work, the characteristics of industrial low voltage distribution network components and the pilot distribution network are measured and modelled with respect topower-line communications frequencies up to 30 MHz. The distributed inductances, capacitances and attenuation of MCMK type low voltage power cables are measured in the frequency band 100 kHz - 30 MHz and an attenuation formula for the cables is formed based on the measurements. The input impedances of electric motors (15-250 kW) are measured using several signal couplings and measurement based input impedance model for electric motor with a slotted stator is formed. The model is designed for the frequency band 10 kHz - 30 MHz. Next, the effect of DC (direct current) voltage link inverter on power line data transfer is briefly analysed. Finally, a pilot distribution network is formed and signal attenuation in communication channels in the pilot environment is measured. The results are compared with the simulations that are carried out utilising the developed models and measured parameters for cables and motors. In the second part of this work, a narrowband power-line data transfer system is developed for the data transfer ofon-line condition monitoring of electric motors. It is developed using standardintegrated circuits. The system is tested in the pilot environment and the applicability of the system for the data transfer required by the on-line condition monitoring of electric motors is analysed.

The high-speed induction motor: calculating the effects of solid-rotor material on machine characteristics

A method for the analysis of high-speed solid-rotor induction motors in presented. The analysis is based on a new combination of the three dimensional linear method and the transfer matrix method. Both saturation and finite length effects are taken into account. The active region of the solid rotor is divided into saturated and unsaturated parts. The time dependence is assumed to be sinusoidal and phasor quantities are used in the solution. The method is applied to the calculation of smooth solid rotors manufactured of different materials. Six rotor materials are tested: three construction steels, pure iron, a cobaltiron alloy and an aluminium alloy. The results obtained by the method agree fairly well with the measurement quantities.

Compliance of crane electrics with electrical safety standards and codes

Master’s thesis focuses on the questions of crane electrics compliance with electrical safety standards. Overview and short comparison of the world’s effective standards in the field is made in order to understand their demands. Basic concepts of a proper electrical circuit design are presented. Characteristics, construction and operation principles of overcurrent protective devices are studied in details. Electrics of the basic crane is designed according to the assumed customer’s demands, compliance with the requirements of the standards is checked. Solutions to achieve better compliance in some issues are proposed. Accent is made on the National Electrical Code (NEC) and standards by Underwriters Laboratories (UL) latests demands. Requirements of the International Electrotechnical Commission (IEC) are also taken into account.

Relationship between electrical conductivity and water content in peat growth medium

Tiivistelmä: Turvekasvualustan sähkönjohtavuuden ja vesipitoisuuden riippuvuus mitattuna TDR-käsimittarilla

Relationship of breast fillet deboning time to shear force, pH, cooking loss and color in broilers stunned by high electrical current

Selostus: Korkealla virranvoimakkuudella tainnutettujen broilereiden rintafileen irroitushetken vaikutus lihaksen leikkausvoiman vastukseen, pH:hon, keittohävikkiin ja väriin