Competitor comparison: variable speed drives in pumping applications

As the world’s energy demand is increasing, a durable solution to control it is to improve the energy efficiency of the processes. It has been estimated that pumping applications have a significant potential for energy savings trough equipment or control system changes. For many pumping application the use of a variable speed drive as a process control element is the most energy efficient solution. The main target of this study is to examine the energy efficiency of a drive system that moves the pump. In a larger scale the purpose of this study is to examine how the different manufacturers’ variable speed drives are functioning as a control device of a pumping process. The idea is to compare the drives from a normal pump user’s point of view. The things that are mattering for the pump user are the efficiency gained in the process and the easiness of the use of the VSD. So some thought is given also on valuating the user-friendliness of the VSDs. The VSDs are compared to each other also on the basis of their life cycle energy costs in different kind of pumping cases. The comparison is made between ACS800 from ABB, VLT AQUA Drive from Danfoss, NX-drive from Vacon and Micromaster 430 from Siemens. The efficiencies are measured in power electronics laboratory in the Lappeenranta University of Technology with a system that consists of a variable speed drive, an induction motor with dc-machine, two power analyzers and a torque transducer. The efficiencies are measured as a function of a load at different frequencies. According to measurement results the differences between the measured system efficiencies on the actual working area of pumping are on average few percent units. When examining efficiencies at the whole range of different loads and frequencies, the differences get bigger. At low frequencies and loads the differences between the most efficient and the least efficient systems are at the most about ten percent units. At the most of the tested points ABB’s drive seem to have slightly better efficiencies than the other drives.

Kymenlaaksolaisten kuljetusyritysten taloudellisen suorituskyvyn kehitys vuosina 1997-2007

Tämän Pro gradu -tutkielman tarkoituksena on tutustua suomalaiseen kuljetustoimialaan erityisesti liiketoiminnallisesta näkökulmasta ja tarkastella suurimpien kymenlaaksolaisten kuljetusyritysten taloudellisen suorituskyvyn sekä muun talouden kehitystä vuosien 1997–2007 aikana. Lisäksi tässä tutkimuksessa pyritään löytämään selittäviä strategisia tekijöitä kymenlaaksolaisyritysten taloudelliselle menestykselle. Kymenlaakson alueen kuljetusyritysten taloudellisen suorituskyvyn osatekijät pysyttelevät koko Suomen kuljetusyritysten lukujen tavoin tutkimuksen tarkastelujakson ajan keskimäärin tyydyttävällä tasolla. Kannattavuuden ja vakavaraisuuden osalta kymenlaaksolaisyritykset näyttävät menestyvän hieman muuta Suomea paremmin, mutta toisaalta yritysten maksukykyisyys jää muita alemmaksi. Tutkimusjakson selkein kehitys kuljetusyrityksillä liittyy sekä huomattavaan toimintakustannusten että liiketoiminnan koon kasvuun. Tutkimuksen kuljetusyrityksistä erityisesti pienimmät ja perinteikkäät, ainoastaan kuljetuspalveluiden tarjontaan keskittyneet toimijat vaikuttavat menestyvän taloudellisesti muita yrityksiä paremmin. Tutkimusyritysten joukossa esiintyy kuitenkin paljon vaihtelua ja mukaan mahtuu niin menestyjiä kuin heikompiakin toimijoita.

Photoelectric Measurements and Modeling of Bacteriorhodopsin

Recent technology has provided us with new information about the internal structures and properties of biomolecules. This has lead to the design of applications based on underlying biological processes. Applications proposed for biomolecules are, for example, the future computers and different types of sensors. One potential biomolecule to be incorporated in the applications is bacteriorhodopsin. Bacteriorhodopsin is a light-sensitive biomolecule, which works in a similar way as the light sensitive cells of the human eye. Bacteriorhodopsin reacts to light by undergoing a complicated series of chemical and thermal transitions. During these transitions, a proton translocation occurs inside the molecule. It is possible to measure the photovoltage caused by the proton translocations when a vast number of molecules is immobilized in a thin film. Also the changes in the light absorption of the film can be measured. This work aimed to develop the electronics needed for the voltage measurements of the bacteriorhodopsin-based optoelectronic sensors. The development of the electronics aimed to get more accurate information about the structure and functionality of these sensors. The sensors used in this work contain a thick film of bacteriorhodopsin immobilized in polyvinylalcohol. This film is placed between two transparent electrodes. The result of this work is an instrumentation amplifier which can be placed in a small space very close to the sensor. By using this amplifier, the original photovoltage can be measured in more detail. The response measured using this amplifier revealed two different components, which could not be distinguished earlier. Another result of this work is the model for the photoelectric response in dry polymer films.

Optimization of short term power trading between Russia, Finland and Baltic countries

Russian and Baltic electricity markets are in the process of reformation and development on the way for competitive and transparent market. Nordic market also undergoes some changes on the way to market integration. Old structure and practices have been expired whereas new laws and rules come into force. The master thesis describes structure and functioning of wholesale electricity markets, cross-border connections between different countries. Additionally methods of cross-border trading using different methods of capacity allocation are disclosed. The main goal of present thesis is to study current situation at different electricity markets and observe changes coming into force as well as the capacity and electricity balances forecast in order to optimize short term power trading between countries and estimate the possible profit for the company.

Paperboard cup with a window

Packaging has to fulfill a lot of demands and the main purpose is to be able to protect the foodstuff packed inside. Typically requirements set on packaging materials reflect the consumer needs. Based on the consumer studies the importance of product visibility is considered as an important property among consumers. However, making the package more transparent the actual shelf life of the product might be reduced. It might have an effect on sensitive foods which contain ingredients vulnerable to light and start to deteriorate more rapidly. The aim for this Masters of Science Thesis was to develop a paperboard cup with a plastic window where different kind of fatty/dry foodstuffs could be stored. The main target was to be able to create an instruction manual how this kind of cup with a window had to be produced without decreasing air tightness and other barrier properties of cupboard material used as a base board. The focus in this work was on designing a shape of the window and finding critical limits for the size, shape and location of the window in the final paperboard cup. Windows were made by cutting holes with different sizes and shapes to different places in the cup blank by using a model cutter. For the windows one plastic film type was selected due to its low oxygen and water vapour transmission properties. The window film was attached to the cup blank by using hot bar and laser seaming methods. Cup manufacturing was done at Stora Enso InnoCentre, Imatra. As a result critical limits for the place, size and shape of the window could be found. The sealing method had a significant effect on the tightness of the cups. Windows didn’t decrease the grip stiffness of the cup. The cup itself gave better light protection than the plastic film used in the windows. The bigger the window, the less the cup could protect the possible foodstuff. Bursting strength was lower in the windows compared to the cup material itself. From environmental point of view DSD licence fees have to be paid due to the amount of used plastic.When using bigger windows the ratio of plastic to fibres increase. This would raise the DSD fee. However, the amount of material is overall reduced which lowers the fee.

Methods for assessing the sustainability of integrated municipal waste management and

The general striving to bring down the number of municipal landfills and to increase the reuse and recycling of waste-derived materials across the EU supports the debates concerning the feasibility and rationality of waste management systems. Substantial decrease in the volume and mass of landfill-disposed waste flows can be achieved by directing suitable waste fractions to energy recovery. Global fossil energy supplies are becoming more and more valuable and expensive energy sources for the mankind, and efforts to save fossil fuels have been made. Waste-derived fuels offer one potential partial solution to two different problems. First, waste that cannot be feasibly re-used or recycled is utilized in the energy conversion process according to EU’s Waste Hierarchy. Second, fossil fuels can be saved for other purposes than energy, mainly as transport fuels. This thesis presents the principles of assessing the most sustainable system solution for an integrated municipal waste management and energy system. The assessment process includes: · formation of a SISMan (Simple Integrated System Management) model of an integrated system including mass, energy and financial flows, and · formation of a MEFLO (Mass, Energy, Financial, Legislational, Other decisionsupport data) decision matrix according to the selected decision criteria, including essential and optional decision criteria. The methods are described and theoretical examples of the utilization of the methods are presented in the thesis. The assessment process involves the selection of different system alternatives (process alternatives for treatment of different waste fractions) and comparison between the alternatives. The first of the two novelty values of the utilization of the presented methods is the perspective selected for the formation of the SISMan model. Normally waste management and energy systems are operated separately according to the targets and principles set for each system. In the thesis the waste management and energy supply systems are considered as one larger integrated system with one primary target of serving the customers, i.e. citizens, as efficiently as possible in the spirit of sustainable development, including the following requirements: · reasonable overall costs, including waste management costs and energy costs; · minimum environmental burdens caused by the integrated waste management and energy system, taking into account the requirement above; and · social acceptance of the selected waste treatment and energy production methods. The integrated waste management and energy system is described by forming a SISMan model including three different flows of the system: energy, mass and financial flows. By defining the three types of flows for an integrated system, the selected factor results needed in the decision-making process of the selection of waste management treatment processes for different waste fractions can be calculated. The model and its results form a transparent description of the integrated system under discussion. The MEFLO decision matrix has been formed from the results of the SISMan model, combined with additional data, including e.g. environmental restrictions and regional aspects. System alternatives which do not meet the requirements set by legislation can be deleted from the comparisons before any closer numerical considerations. The second novelty value of this thesis is the three-level ranking method for combining the factor results of the MEFLO decision matrix. As a result of the MEFLO decision matrix, a transparent ranking of different system alternatives, including selection of treatment processes for different waste fractions, is achieved. SISMan and MEFLO are methods meant to be utilized in municipal decision-making processes concerning waste management and energy supply as simple, transparent and easyto- understand tools. The methods can be utilized in the assessment of existing systems, and particularly in the planning processes of future regional integrated systems. The principles of SISMan and MEFLO can be utilized also in other environments, where synergies of integrating two (or more) systems can be obtained. The SISMan flow model and the MEFLO decision matrix can be formed with or without any applicable commercial or free-of-charge tool/software. SISMan and MEFLO are not bound to any libraries or data-bases including process information, such as different emission data libraries utilized in life cycle assessments.

Implementation and Integration of New Baggage Logistic Centre at HelsinkiVantaa Airport

This thesis deals with improving international airport baggage supply chain management (SCM) by means of information technology and new baggage handling system. This study aims to focus on supply chain visibility in practice and to suggest different ways to improve the supply chain performance through information sharing. The objective is also to define how radio frequency identification (RFID) and enterprise resource planning (ERP) can make processes more transparent. In order to get full benefits from processes, effective business process management and monitoring as well as the key performance indicators must be defined, implemented and visualized through e.g. dashboard views for different roles. As an outcome of the research the need for the use of information technology systems and more advanced technologies, e.g. RFID in the supply chain management is evident. Sophisticated ERP is crucial in boosting SCM business processes and profitability. This would be beneficial for dynamic decision making as well in the airport and airline supply chain management. In the long term, economic aspects support the actions I have suggested in order to make production more flexible in reacting to quick changes.

Etelä-Karjalan sosiaali- ja terveyspiirin kuntakohtaisen kustannuslaskentamallin kehittäminen

Työn tavoitteena oli tutkia Etelä-Karjalan sosiaali- ja terveydenhuollon kuntayhtymän kuntalaskutusta ja rakentaa laskentamalli, jolla kuntakohtaiset kustannukset pystytään laskemaan ja jakamaan. Tutkimusote oli konstruktiivinen. Tiedot kerättiin kuntayhtymän toiminta- ja taloustietojärjestelmistä sekä haastattelemalla organisaation asiantuntijoita. Työn tulokseksi saatu laskentamalli koostuu suoritepohjaisesta, asukaslukupohjaisista ja tarvepainotetuista asukaslukupohjaisista kustannusajureista, joilla kustannukset jaetaan piirin jäsenkunnille. Tällä sekamallilla pystytään toteuttamaan kuntalaskutusta, sillä se täyttää kuntalaskutusmallille asetetut vaatimukset. Työn tulosten perusteella tulo-osuusmalli olisi paras tapa toteuttaa kuntalaskutusta. Yksinkertainen rahoitusmalli mahdollistaa toiminnan vapaamman kehittämisen kuin sekamalli ja on lisäksi selkeämpi ja läpinäkyvämpi. Sekamallissa tulisi painottaa tarvepohjaisia asukaslukuajureita. Tärkeimmät ja suurimpia kustannuksia aiheuttavat alueet kannattaisi tuotteistaa.

Online Ultrasound Measurements of Membrane Compaction

There are several filtration applications in the pulp and paper industry where the capacity and cost-effectiveness of processes are of importance. Ultrafiltration is used to clean process water. Ultrafiltration is a membrane process that separates a certain component or compound from a liquid stream. The pressure difference across the membrane sieves macromolecules smaller than 0.001-0.02 μm through the membrane. When optimizing the filtration process capacity, online information about the conditions of the membrane is needed. Fouling and compaction of the membrane both affect the capacity of the filtration process. In fouling a “cake” layer starts to build on the surface of the membrane. This layer blocks the molecules from sieving through the membrane thereby decreasing the yield of the process. In compaction of the membrane the structure is flattened out because of the high pressure applied. The higher pressure increases the capacity but may damage the structure of the membrane permanently. Information about the compaction is needed to effectively operate the filters. The objective of this study was to develop an accurate system for online monitoring of the condition of the membrane using ultrasound reflectometry. Measurements of ultrafiltration membrane compaction were made successfully utilizing ultrasound. The results were confirmed by permeate flux decline, measurements of compaction with a micrometer, mechanical compaction using a hydraulic piston and a scanning electron microscope (SEM). The scientific contribution of this thesis is to introduce a secondary ultrasound transducer to determine the speed of sound in the fluid used. The speed of sound is highly dependent on the temperature and pressure used in the filters. When the exact speed of sound is obtained by the reference transducer, the effect of temperature and pressure is eliminated. This speed is then used to calculate the distances with a higher accuracy. As the accuracy or the resolution of the ultrasound measurement is increased, the method can be applied to a higher amount of applications especially for processes where fouling layers are thinner because of smaller macromolecules. With the help of the transducer, membrane compaction of 13 μm was measured in the pressure of 5 bars. The results were verified with the permeate flux decline, which indicated that compaction had taken place. The measurements of compaction with a micrometer showed compaction of 23–26 μm. The results are in the same range and confirm the compaction. Mechanical compaction measurements were made using a hydraulic piston, and the result was the same 13 μm as obtained by applying the ultrasound time domain reflectometry (UTDR). A scanning electron microscope (SEM) was used to study the structure of the samples before and after the compaction.

Identifying first graders at risk of reading and writing difficulties : creating a group-based screening tool in kiswahili in Tanzania

Early identification of beginning readers at risk of developing reading and writing difficulties plays an important role in the prevention and provision of appropriate intervention. In Tanzania, as in other countries, there are children in schools who are at risk of developing reading and writing difficulties. Many of these children complete school without being identified and without proper and relevant support. The main language in Tanzania is Kiswahili, a transparent language. Contextually relevant, reliable and valid instruments of identification are needed in Tanzanian schools. This study aimed at the construction and validation of a group-based screening instrument in the Kiswahili language for identifying beginning readers at risk of reading and writing difficulties. In studying the function of the test there was special interest in analyzing the explanatory power of certain contextual factors related to the home and school. Halfway through grade one, 337 children from four purposively selected primary schools in Morogoro municipality were screened with a group test consisting of 7 subscales measuring phonological awareness, word and letter knowledge and spelling. A questionnaire about background factors and the home and school environments related to literacy was also used. The schools were chosen based on performance status (i.e. high, good, average and low performing schools) in order to include variation. For validation, 64 children were chosen from the original sample to take an individual test measuring nonsense word reading, word reading, actual text reading, one-minute reading and writing. School marks from grade one and a follow-up test half way through grade two were also used for validation. The correlations between the results from the group test and the three measures used for validation were very high (.83-.95). Content validity of the group test was established by using items drawn from authorized text books for reading in grade one. Construct validity was analyzed through item analysis and principal component analysis. The difficulty level of most items in both the group test and the follow-up test was good. The items also discriminated well. Principal component analysis revealed one powerful latent dimension (initial literacy factor), accounting for 93% of the variance. This implies that it could be possible to use any set of the subtests of the group test for screening and prediction. The K-Means cluster analysis revealed four clusters: at-risk children, strugglers, readers and good readers. The main concern in this study was with the groups of at-risk children (24%) and strugglers (22%), who need the most assistance. The predictive validity of the group test was analyzed by correlating the measures from the two school years and by cross tabulating grade one and grade two clusters. All the correlations were positive and very high, and 94% of the at-risk children in grade two were already identified in the group test in grade one. The explanatory power of some of the home and school factors was very strong. The number of books at home accounted for 38% of the variance in reading and writing ability measured by the group test. Parents´ reading ability and the support children received at home for schoolwork were also influential factors. Among the studied school factors school attendance had the strongest explanatory power, accounting for 21% of the variance in reading and writing ability. Having been in nursery school was also of importance. Based on the findings in the study a short version of the group test was created. It is suggested for use in the screening processes in grade one aiming at identifying children at risk of reading and writing difficulties in the Tanzanian context. Suggestions for further research as well as for actions for improving the literacy skills of Tanzanian children are presented.

Novel force control methods in a teleoperation system of a hydraulic slider

The objective of the this research project is to develop a novel force control scheme for the teleoperation of a hydraulically driven manipulator, and to implement an ideal transparent mapping between human and machine interaction, and machine and task environment interaction. This master‘s thesis provides a preparatory study for the present research project. The research is limited into a single degree of freedom hydraulic slider with 6-DOF Phantom haptic device. The key contribution of the thesis is to set up the experimental rig including electromechanical haptic device, hydraulic servo and 6-DOF force sensor. The slider is firstly tested as a position servo by using previously developed intelligent switching control algorithm. Subsequently the teleoperated system is set up and the preliminary experiments are carried out. In addition to development of the single DOF experimental set up, methods such as passivity control in teleoperation are reviewed. The thesis also contains review of modeling of the servo slider in particular reference to the servo valve. Markov Chain Monte Carlo method is utilized in developing the robustness of the model in presence of noise.

Tavaran toimitusasiakirjojen sähköistäminen

Tutkielman tavoitteena on selvittää sähköisten tavaran toimitusasiakirjojen käytön vaikutukset hankinta- ja logistiikkapalveluita tarjoavan yrityksen toimitusketjun loppupään toimintoihin. Lisäksi työssä rakennetaan konstruktiivisen tutkimusmenetelmän viitekehyksen mukainen toimintamalli yrityksen käyttöä varten. Toimintamallin avulla tarkastellaan kohdeyrityksen mahdollisuutta parantaa toimitusketjun läpinäkyvyyttä, tehostaa sidosryhmien välistä tiedonsiirtoa ja vähentää virheitä ja manuaalista työtä nykyisissä prosesseissa. Työn keskeisin sisältö rakentuu kohdeyrityksen käyttämille kuljetusyrityksille tehdyn kuljetusliikekyselyn, tarkkaan kuvatun nykytilan sekä käytännön ongelmaan rakennetun konstruktion ympärille. Kuljetusliikekyselyn avulla saadaan käyttökelpoinen kuva kuljetusyritysten nykytilasta sekä tulevaisuuden suunnitelmista sähköisiin tavaran toimitusasiakirjoihin liittyen. Nykytilan kuvauksella nostetaan esiin prosesseja ja toimintoja joiden toimintaan voidaan oleellisesti vaikuttaa informaatioteknologian sekä prosessimuutosten avulla. Konstruktion rakentamisessa pääpaino on suunnattu läpinäkyvän ja tehokkaan toimitusketjun aikaansaamisessa. Tutkielman konstruktiota, sähköisten tavaran toimitusasiakirjojen toimintamallia, tarkastellaan yrityksen liiketoiminnan näkökulmasta peilaamalla oletettuja parannuksia aikaisempaan teoriapohjaan. Lisäksi toimintamallin soveltumista reaalimaailman ongelman ratkaisuun arvioidaan diplomityön ohjausryhmästä koostuvan johtajapaneelin tekemällä SWOT-analyysillä sekä heikolla markkinatestillä. Sidosryhmien välisen toiminnan tehostumista arvioidaan kvalitatiivisin menetelmin

Ion selective electrodes for determination of low and ultra low concentrations of lead (II) in natural waters

Att övervaka förekomsten av giftiga komponenter i naturliga vattendrag är nödvändigt för människans välmående. Eftersom halten av föroreningar i naturens ekosystem bör hållas möjligast låg, pågår en ständig jakt efter kemiska analysmetoder med allt lägre detektionsgränser. I dagens läge görs miljöanalyser med dyr och sofistikerad instrumentering som kräver mycket underhåll. Jonselektiva elektroder har flera goda egenskaper som t.ex. bärbarhet, låg energiförbrukning, och dessutom är de relativt kostnadseffektiva. Att använda jonselektiva elektroder vid miljöanalyser är möjligt om deras känslighetsområde kan utvidgas genom att sänka deras detektionsgränser. För att sänka detektionsgränsen för Pb(II)-selektiva elektroder undersöktes olika typer av jonselektiva membran som baserades på polyakrylat-kopolymerer, PVC och PbS/Ag2S. Fast-fas elektroder med membran av PbS/Ag2S är i allmänhet enklare och mer robusta än konventionella elektroder vid spårämnesanalys av joniska föroreningar. Fast-fas elektrodernas detektionsgräns sänktes i detta arbete med en nyutvecklad galvanostatisk polariseringsmetod och de kunde sedan framgångsrikt användas för kvantitativa bestämningar av bly(II)-halter i miljöprov som hade samlats in i den finska skärgården nära tidigare industriområden. Analysresultaten som erhölls med jonselektiva elektroder bekräftades med andra analytiska metoder. Att sänka detektionsgränsen m.hj.a. den nyutvecklade polariseringsmetoden möjliggör bestämning av låga och ultra-låga blyhalter som inte kunde nås med klassisk potentiometri. Den verkliga fördelen med att använda dessa blyselektiva elektroder är möjligheten att utföra mätningar i obehandlade miljöprov trots närvaron av fasta partiklar vilket inte är möjligt att göra med andra analysmetoder. Jag väntar mig att den nyutvecklade polariseringsmetoden kommer att sätta en trend i spårämnesanalys med jonselektiva elektroder.

Accuracy Analysis of Frequency Converter Estimates in Diagnostic Applications

Transportation of fluids is one of the most common and energy intensive processes in the industrial and HVAC sectors. Pumping systems are frequently subject to engineering malpractice when dimensioned, which can lead to poor operational efficiency. Moreover, pump monitoring requires dedicated measuring equipment, which imply costly investments. Inefficient pump operation and improper maintenance can increase energy costs substantially and even lead to pump failure. A centrifugal pump is commonly driven by an induction motor. Driving the induction motor with a frequency converter can diminish energy consumption in pump drives and provide better control of a process. In addition, induction machine signals can also be estimated by modern frequency converters, dispensing with the use of sensors. If the estimates are accurate enough, a pump can be modelled and integrated into the frequency converter control scheme. This can open the possibility of joint motor and pump monitoring and diagnostics, thereby allowing the detection of reliability-reducing operating states that can lead to additional maintenance costs. The goal of this work is to study the accuracy of rotational speed, torque and shaft power estimates calculated by a frequency converter. Laboratory tests were performed in order to observe estimate behaviour in both steady-state and transient operation. An induction machine driven by a vector-controlled frequency converter, coupled with another induction machine acting as load was used in the tests. The estimated quantities were obtained through the frequency converter’s Trend Recorder software. A high-precision, HBM T12 torque-speed transducer was used to measure the actual values of the aforementioned variables. The effect of the flux optimization energy saving feature on the estimate quality was also studied. A processing function was developed in MATLAB for comparison of the obtained data. The obtained results confirm the suitability of this particular converter to provide accurate enough estimates for pumping applications.

Automated Purchase to Pay Process Value Modeling and Comparative Process Speeds

The importance of efficient supply chain management has increased due to globalization and the blurring of organizational boundaries. Various supply chain management technologies have been identified to drive organizational profitability and financial performance. Organizations have historically been concentrating heavily on the flow of goods and services, while less attention has been dedicated to the flow of money. While supply chains are becoming more transparent and automated, new opportunities for financial supply chain management have emerged through information technology solutions and comprehensive financial supply chain management strategies. This research concentrates on the end part of the purchasing process which is the handling of invoices. Efficient invoice processing can have an impact on organizations working capital management and thus provide companies with better readiness to face the challenges related to cash management. Leveraging a process mining solution the aim of this research was to examine the automated invoice handling process of four different organizations. The invoice data was collected from each organizations invoice processing system. The sample included all the invoices organizations had processed during the year 2012. The main objective was to find out whether e-invoices are faster to process in an automated invoice processing solution than scanned invoices (post entry into invoice processing solution). Other objectives included looking into the longest lead times between process steps and the impact of manual process steps on cycle time. Processing of invoices from maverick purchases was also examined. Based on the results of the research and previous literature on the subject, suggestions for improving the process were proposed. The results of the research indicate that scanned invoices were processed faster than e-invoices. This is mostly due to the more complex processing of e-invoices. It should be noted however that the manual tasks related to turning a paper invoice into electronic format through scanning are ignored in this research. The transitions with the longest lead times in the invoice handling process included both pre-automated steps as well as manual steps performed by humans. When the most common manual steps were examined in more detail, it was clear that these steps had a prolonging impact on the process. Regarding invoices from maverick purchases the evidence shows that these invoices were slower to process than invoices from purchases conducted through e-procurement systems and from preferred suppliers. Suggestions on how to improve the process included: increasing invoice matching, reducing of manual steps and leveraging of different value added services such as invoice validation service, mobile solutions and supply chain financing services. For companies that have already reaped all the process efficiencies the next step is to engage in collaborative financial supply chain management strategies that can benefit the whole supply chain.