Analog performance of double gate SOI transistors

Double gate fully depleted silicon-on-insulator (DGSOI) is recognized as a possible solution when the physical gate length L-G reduces to 25nm for the 65nm node on the ITRS CMOS roadmap. In this paper, scaling guidelines are introduced to optimally design a nanoscale DGSOI. For this reason, the sensitivity of gain, f(T) and f(max) to each of the key geometric and technological parameters of the DGSOI are assessed and quantified using MixedMode simulation. The impact of the parasitic resistance and capacitance on analog device performance is systematically analysed. By comparing analog performance with a single gate (SG), it has been found that intrinsic gain in DGSOI is 4 times higher but its fT was found to be comparable to that of SGSOI at different regions of transistor operation. However, the extracted fmax in SG SOI was higher (similar to 40%) compared to DGSOI due to its lower capacitance.

The design and performance of a 2.5-GHz telecommand link for wireless biomedical monitoring

This paper details the implementation and operational performance of a minimum-power 2.45-GHz pulse receiver and a companion on-off keyed transmitter for use in a semi-active duplex RF biomedical transponder. A 50-Ohm microstrip stub-matched zero-bias diode detector forms the heart of a body-worn receiver that has a CMOS baseband amplifier consuming 20 microamps from +3 V and achieves a tangential sensitivity of -53 dBm. The base transmitter generates 0.5 W of peak RF output power into 50 Ohms. Both linear and right-hand circularly polarized Tx-Rx antenna sets were employed in system reliability trials carried out in a hospital Coronary Care Unit, For transmitting antenna heights between 0.3 and 2.2 m above floor level, transponder interrogations were 95% reliable within the 67-m-sq area of the ward, falling to an average of 46 % in the surrounding rooms and corridors. Overall, the circular antenna set gave the higher reliability and lower propagation power decay index.

Subpixel interpolation architecture for multistandard video motion estimation

A new reconfigurable subpixel interpolation architecture for multistandard (e.g., MPEG-2, MPEG-4, H.264, and AVS) video motion estimation (ME) is presented. This exploits the mixed use of parallel and serial-input FIR filters to achieve high throughput rate and efficient silicon utilization. Silicon design studies show that this can be implemented using 34.8 × 10 3 gates with area and performance that compares very favorably with specific fixed solutions, e.g., for the H.264 standard alone. This can support SDTV and HDTV applications when implemented in 0.18 µm CMOS technology, with further performance enhancements achievable at 0.13 µm and below. © 2009 IEEE.

Online CORDIC algorithm and VLSI architecture for implementing QR-array processors

A novel most significant digit first CORDIC architecture is presented that is suitable for the VLSI design of systolic array processor cells for performing QR decomposition. This is based on an on-line CORDIC algorithm with a constant scale factor and a latency independent of the wordlength. This has been derived through the extension of previously published CORDIC algorithms. It is shown that simplifying the calculation of convergence bounds also greatly simplifies the derivation of suitable VLSI architectures. Design studies, based on a 0.35-µ CMOS standard cell process, indicate that 20 such QR processor cells operating at rates suitable for radar beamfoming can be readily accommodated on a single chip.

Low-cost digital signature architecture suitable for radio frequency identification tags

Continuing achievements in hardware technology are bringing ubiquitous computing closer to reality. The notion of a connected, interactive and autonomous environment is common to all sensor networks, biosystems and radio frequency identification (RFID) devices, and the emergence of significant deployments and sophisticated applications can be expected. However, as more information is collected and transmitted, security issues will become vital for such a fully connected environment. In this study the authors consider adding security features to low-cost devices such as RFID tags. In particular, the authors consider the implementation of a digital signature architecture that can be used for device authentication, to prevent tag cloning, and for data authentication to prevent transmission forgery. The scheme is built around the signature variant of the cryptoGPS identification scheme and the SHA-1 hash function. When implemented on 130 nm CMOS the full design uses 7494 gates and consumes 4.72 mu W of power, making it smaller and more power efficient than previous low-cost digital signature designs. The study also presents a low-cost SHA-1 hardware architecture which is the smallest standardised hash function design to date.

Design of quantum-dot cellular automata circuits using cut-set retiming

As a potential alternative to CMOS technology, QCA provides an interesting paradigm in both communication and computation. However, QCAs unique four-phase clocking scheme and timing constraints present serious timing issues for interconnection and feedback. In this work, a cut-set retiming design procedure is proposed to resolve these QCA timing issues. The proposed design procedure can accommodate QCAs unique characteristics by performing delay-transfer and time-scaling to reallocate the existing delays so as to achieve efficient clocking zone assignment. Cut-set retiming makes it possible to effectively design relatively complex QCA circuits that include feedback. It utilizes the similar characteristics of synchronization, deep pipelines and local interconnections common to both QCA and systolic architectures. As a case study, a systolic Montgomery modular multiplier is designed to illustrate the procedure. Furthermore, a nonsystolic architecture, an S27 benchmark circuit, is designed and compared with previous designs. The comparison shows that the cut-set retiming method achieves a more efficient design, with a reduction of 22%, 44%, and 46% in terms of cell count, area, and latency, respectively.

QCA Systolic array design

Quantum-dot Cellular Automata (QCA) technology is a promising potential alternative to CMOS technology. To explore the characteristics of QCA and suitable design methodologies, digital circuit design approaches have been investigated. Due to the inherent wire delay in QCA, pipelined architectures appear to be a particularly suitable design technique. Also, because of the pipeline nature of QCA technology, it is not suitable for complicated control system design. Systolic arrays take advantage of pipelining, parallelism and simple local control. Therefore, an investigation into these architectures in QCA technology is provided in this paper. Two case studies, (a matrix multiplier and a Galois Field multiplier) are designed and analyzed based on both multilayer and coplanar crossings. The performance of these two types of interconnections are compared and it is found that even though coplanar crossings are currently more practical, they tend to occupy a larger design area and incur slightly more delay. A general semi-conductor QCA systolic array design methodology is also proposed. It is found that by applying a systolic array structure in QCA design, significant benefits can be achieved particularly with large systolic arrays, even more so than when applied in CMOS-based technology.

Image processing chip for small object detection

A new, front-end image processing chip is presented for real-time small object detection. It has been implemented using a 0.6 µ, 3.3 V CMOS technology and operates on 10-bit input data at 54 megasamples per second. It occupies an area of 12.9 mm×13.6 mm (including pads), dissipates 1.5 W, has 92 I/O pins and is to be housed in a 160-pin ceramic quarter flat-pack. It performs both one- and two-dimensional FIR filtering and a multilayer perceptron (MLP) neural network function using a reconfigurable array of 21 multiplication-accumulation cells which corresponds to a window size of 7×3. The chip can cope with images of 2047 pixels per line and can be cascaded to cope with larger window sizes. The chip performs two billion fixed point multiplications and additions per second.

64-point Fourier transform chip for digital television applications

A 64-point Fourier transform chip is described that performs a forward or inverse, 64-point Fourier transform on complex two's complement data supplied at a rate of 13.5MHz and can operate at clock rates of up to 40MHz, under worst-case conditions. It uses a 0.6µm double-level metal CMOS technology, contains 535k transistors and uses an internal 3.3V power supply. It has an area of 7.8×8mm, dissipates 0.9W, has 48 pins and is housed in a 84 pin PLCC plastic package. The chip is based on a FFT architecture developed from first principles through a detailed investigation of the structure of the relevant DFT matrix and through mapping repetitive blocks within this matrix onto a regular silicon structure.

A VLSI architecture for multiplication, division and square root

A high-performance VLSI architecture to perform combined multiply-accumulate, divide, and square root operations is proposed. The circuit is highly regular, requires only minimal control, and can be reconfigured for every cycle. The execution time for each operation is the same. The combination of redundancy and pipelining results in a throughput independent of the wordsize of the array. With current CMOS technology, throughput rates in excess of 80 million operations per second are achievable.

A 64-point fourier transform chip for video motion compensation using phase correlation

Details of a new low power fast Fourier transform (FFT) processor for use in digital television applications are presented. This has been fabricated using a 0.6-µm CMOS technology and can perform a 64 point complex forward or inverse FFT on real-time video at up to 18 Megasamples per second. It comprises 0.5 million transistors in a die area of 7.8 × 8 mm and dissipates 1 W. The chip design is based on a novel VLSI architecture which has been derived from a first principles factorization of the discrete Fourier transform (DFT) matrix and tailored to a direct silicon implementation.

VLSI module for high-performance multiply, square root and divide

A high-performance VLSI architecture to perform multiply-accumulate, division and square root operations is proposed. The circuit is highly regular, requires only minimal control and can be pipelined right down to the bit level. The system can also be reconfigured on every cycle to perform any one of these operations. The gate count per row has been estimated at (27n+70) gate equivalents where n is the divisor wordlength. The throughput rate, which equals the clock speed, is the same for each operation and is independent of the wordlength. This is achieved through the combination of pipelining and redundant arithmetic. With a 1.0 µm CMOS technology and extensive pipelining, throughput rates in excess of 70 million operations per second are expected.

JPEG encoder system-on-a-chip demonstrator

The design of a System-on-a-Chip (SoC) demonstrator for a baseline JPEG encoder core is presented. This combines a highly optimized Discrete Cosine Transform (DCT) and quantization unit with an entropy coder which has been realized using off-the-shelf synthesizable IP cores (Run-length coder, Huffman coder and data packer). When synthesized in a 0.35 µm CMOS process, the core can operate at speeds up to 100 MHz and contains 50 k gates plus 11.5 kbits of RAM. This is approximately 20% less than similar JPEG encoder designs reported in literature. When targeted at FPGA the core can operate up to 30 MHz and is capable of compressing 9-bit full-frame color input data at NTSC or PAL rates.

Discrete cosine transform generator for VLSI synthesis

A generator for the automated design of Discrete Cosine Transform (DCT) cores is presented. This can be used to rapidly create silicon circuits from a high level specification. These compare very favourably with existing designs. The DCT cores produced are scaleable in terms of point size as well as input/output and coefficient wordlengths. This provides a high degree of flexibility. An example, 8-point 1D DCT design, produced occupies less than 0.92 mm when implemented in a 0.35µ double level metal CMOS technology. This can be clocked at a rate of 100MHz.