Entsymaattisen hydrolyysin vaikutuksista mikrokiteisen selluloosan rakenteeseen

Cellulose can be used as a renewable raw material for energy production. The utilization requires degradation of cellulose into glucose, which can be done with the aid of enzymatic hydrolysis. In this thesis, various x-ray methods were used to characterize sub-micrometer changes in microcrystalline cellulose during enzymatic hydrolysis to clarify the process and factors slowering it. The methods included wide-angle x-ray scattering (WAXS), small-angle x-ray scattering (SAXS) and x-ray microtomography. In addition, the samples were studied with transmission electron microscopy (TEM). The studied samples were hydrolyzed by enzymes of the Trichoderma reesei species for 6, 24, and 75 hours, which corresponded to 31 %, 58 %, and 68 % degrees of hydrolysis, respectively. Freeze-dried hydrolysis residues were measured with WAXS, SAXS and microtomography, whereas some of them were re-wetted for the wet SAXS and TEM measurements. The microtomography measurements showed a clear decrease in particle size in scale of tens of micrometers. In all the TEM pictures similar cylindrical and partly ramified structures were observed, independent of the hydrolysis time. The SAXS results were ambiguous and partly imprecise, but showed a change in the structure of wet samples in scale of 10-30 nm. According to the WAXS results, the degrees of crystallinity and the crystal sizes remained the same. The gained results support the assuption, that the cellulosic particles are hydrolyzed mostly on their surface, since the enzymes are unable to penetrate into the nanopores of wet cellulose. The hydrolysis therefore proceeds quickly in easily accessible particles and leaves the unaccesible particles almost untouched. The structural changes observed in the SAXS measurements might correspond to slight loosening of the microfibril aggregates, which was seen only in the wet samples because of their different pore structure.

Properties of Ammonium Nitrate based fertilisers

The text is divided into three parts; Properties, Application and Safety of Ammonium Nitrate (AN) based fertilisers. In Properties, the structures and phase transitions of ammonium and potassium nitrate are reviewed. The consequences of phase transitions affect the proper use of fertilisers. Therefore the products must be stabilised against the volume changes and consequent loss of bulk density and hardness, formation of dust and finally caking of fertilisers. The effect of different stabilisers is discussed. Magnesium nitrate, ammonium sulphate and potassium nitrate are presented as a good compromise. In the Application part, the solid solutions in the systems (K+,NH4+)NO3- and (NH4+,K+)(Cl-,NO3-) are presented based on studies made with DSC and XRD. As there are clear limits for solute content in the solvent lattice, a number of disproportionation transitions exist in these process phases, e.g., N3 (solid solution isomorphous to NH4NO3-III) disproportionates to phases K3 (solid solution isomorphous to KNO3-III) and K2 (solid solution isomorphous to KNO3-II). In the crystallisation experiments, the formation of K3 depends upon temperature and the ratio K/(K+NH4). The formation of phases K3, N3, and K2 was modelled as a function of temperature and the mole ratios. In introducing chlorides, two distinct maxima for K3 were found. Confirmed with commercial potash samples, the variables affecting the reaction of potassium chloride with AN are the particle size, time, temperature, moisture content and amount of organic coating. The phase diagrams obtained by crystallisation studies were compared with a number of commercial fertilisers and, with regard to phase composition, the temperature and moisture content are critical when the formation and stability of solid solutions are considered. The temperature where the AN-based fertiliser is solidified affects the amount of compounds crystallised at that point. In addition, the temperature where the final moisture is evaporated affects the amount and type of solid solution formed at this temperature. The amount of remaining moisture affects the stability of the K3 phase. The K3 phase is dissolved by the moisture and recrystallised into the quantities of K3, which is stable at the temperature where the sample is kept. The remaining moisture should not be free; it should be bound as water in the final product. The temperatures during storage also affect the quantity of K3 phase. As presented in the figures, K3 phase is not stable at temperatu¬res below 30 °C. If the temperature is about 40 °C, the K3 phase can be formed due to the remaining moisture. In the Safety part, self-sustaining decomposition (SSD), oxidising and energetic properties of fertilisers are discussed. Based on the consequence analysis of SSD, early detection of decomposition in warehouses and proper temperature control in the manufacturing process is important. SSD and oxidising properties were found in compositions where K3 exists. It is assumed that potassium nitrate forms a solid matrix in which AN can decompose. The oxidising properties can be affected by the form of the product. Granular products are inherently less oxidising. Finally energetic properties are reviewed. The composition of the fertiliser has an importance based on theoretical calculations supported by experimental studies. Materials such as carbonates and sulphates act as diluents. An excess of ammonium ions acts as a fuel although this is debatable. Based on the experimental work, the physical properties have a major importance over the composition. A high bulk density is of key importance for detonation resistance.

Precipitation-induced runoff and leaching from milled peat mining mires by peat types : a comparative method for estimating the loading of water bodies during peat pruduction

Precipitation-induced runoff and leaching from milled peat mining mires by peat types: a comparative method for estimating the loading of water bodies during peat production. This research project in environmental geology has arisen out of an observed need to be able to predict more accurately the loading of watercourses with detrimental organic substances and nutrients from already existing and planned peat production areas, since the authorities capacity for insisting on such predictions covering the whole duration of peat production in connection with evaluations of environmental impact is at present highly limited. National and international decisions regarding monitoring of the condition of watercourses and their improvement and restoration require more sophisticated evaluation methods in order to be able to forecast watercourse loading and its environmental impacts at the stage of land-use planning and preparations for peat production.The present project thus set out from the premise that it would be possible on the basis of existing mire and peat data properties to construct estimates for the typical loading from production mires over the whole duration of their exploitation. Finland has some 10 million hectares of peatland, accounting for almost a third of its total area. Macroclimatic conditions have varied in the course of the Holocene growth and development of this peatland, and with them the habitats of the peat-forming plants. Temperatures and moisture conditions have played a significant role in determining the dominant species of mire plants growing there at any particular time, the resulting mire types and the accumulation and deposition of plant remains to form the peat. The above climatic, environmental and mire development factors, together with ditching, have contributed, and continue to contribute, to the existence of peat horizons that differ in their physical and chemical properties, leading to differences in material transport between peatlands in a natural state and mires that have been ditched or prepared for forestry and peat production. Watercourse loading from the ditching of mires or their use for peat production can have detrimental effects on river and lake environments and their recreational use, especially where oxygen-consuming organic solids and soluble organic substances and nutrients are concerned. It has not previously been possible, however, to estimate in advance the watercourse loading likely to arise from ditching and peat production on the basis of the characteristics of the peat in a mire, although earlier observations have indicated that watercourse loading from peat production can vary greatly and it has been suggested that differences in peat properties may be of significance in this. Sprinkling is used here in combination with simulations of conditions in a milled peat production area to determine the influence of the physical and chemical properties of milled peats in production mires on surface runoff into the drainage ditches and the concentrations of material in the runoff water. Sprinkling and extraction experiments were carried out on 25 samples of milled Carex (C) and Sphagnum (S) peat of humification grades H 2.5 8.5 with moisture content in the range 23.4 89% on commencement of the first sprinkling, which was followed by a second sprinkling 24 hours later. The water retention capacity of the peat was best, and surface runoff lowest, with Sphagnum and Carex peat samples of humification grades H 2.5 6 in the moisture content class 56 75%. On account of the hydrophobicity of dry peat, runoff increased in a fairly regular manner with drying of the sample from 55% to 24 30%. Runoff from the samples with an original moisture content over 55% increased by 63% in the second round of sprinkling relative to the first, as they had practically reached saturation point on the first occasion, while those with an original moisture content below 55% retained their high runoff in the second round, due to continued hydrophobicity. The well-humified samples (H 6.5 8.5) with a moisture content over 80% showed a low water retention capacity and high runoff in both rounds of sprinkling. Loading of the runoff water with suspended solids, total phosphorus and total nitrogen, and also the chemical oxygen demand (CODMn O2), varied greatly in the sprinkling experiment, depending on the peat type and degree of humification, but concentrations of the same substances in the two sprinklings were closely or moderately closely correlated and these correlations were significant. The concentrations of suspended solids in the runoff water observed in the simulations of a peat production area and the direct surface runoff from it into the drainage ditch system in response to rain (sprinkling intensity 1.27 mm/min) varied c. 60-fold between the degrees of humification in the case of the Carex peats and c. 150-fold for the Sphagnum peats, while chemical oxygen demand varied c. 30-fold and c. 50-fold, respectively, total phosphorus c. 60-fold and c. 66-fold, total nitrogen c. 65-fold and c. 195-fold and ammonium nitrogen c. 90-fold and c. 30-fold. The increases in concentrations in the runoff water were very closely correlated with increases in humification of the peat. The correlations of the concentrations measured in extraction experiments (48 h) with peat type and degree of humification corresponded to those observed in the sprinkler experiments. The resulting figures for the surface runoff from a peat production area into the drainage ditches simulated by means of sprinkling and material concentrations in the runoff water were combined with statistics on the mean extent of daily rainfall (0 67 mm) during the frost-free period of the year (May October) over an observation period of 30 years to yield typical annual loading figures (kg/ha) for suspended solids (SS), chemical oxygen demand of organic matter (CODmn O2), total phosphorus (tot. P) and total nitrogen (tot. N) entering the ditches with respect to milled Carex (C) and Sphagnum (S) peats of humification grades H 2.5 8.5. In order to calculate the loading of drainage ditches from a milled peat production mire with the aid of these annual comparative values (in kg/ha), information is required on the properties of the intended production mire and its peat. Once data are available on the area of the mire, its peat depth, peat types and their degrees of humification, dry matter content, calorific value and corresponding energy content, it is possible to produce mutually comparable estimates for individual mires with respect to the annual loading of the drainage ditch system and the surrounding watercourse for the whole service life of the production area, the duration of this service life, determinations of energy content and the amount of loading per unit of energy generated (kg/MWh). In the 8 mires in the Köyhäjoki basin, Central Ostrobothnia, taken as an example, the loading of suspended solids (SS) in the drainage ditch networks calculated on the basis of the typical values obtained here and existing mire and peat data and expressed per unit of energy generated varied between the mires and horizons in the range 0.9 16.5 kg/MWh. One of the aims of this work was to develop means of making better use of existing mire and peat data and the results of corings and other field investigations. In this respect combination of the typical loading values (kg/ha) obtained here for S, SC, CS and C peats and the various degrees of humification (H 2.5 8.5) with the above mire and peat data by means of a computer program for the acquisition and handling of such data would enable all the information currently available and that deposited in the system in the future to be used for defining watercourse loading estimates for mires and comparing them with the corresponding estimates of energy content. The intention behind this work has been to respond to the challenge facing the energy generation industry to find larger peat production areas that exert less loading on the environment and to that facing the environmental authorities to improve the means available for estimating watercourse loading from peat production and its environmental impacts in advance. The results conform well to the initial hypothesis and to the goals laid down for the research and should enable watercourse loading from existing and planned peat production to be evaluated better in the future and the resulting impacts to be taken into account when planning land use and energy generation. The advance loading information available in this way would be of value in the selection of individual peat production areas, the planning of their exploitation, the introduction of water protection measures and the planning of loading inspections, in order to achieve controlled peat production that pays due attention to environmental considerations.

E. G. Gulinin ekumeeninen työ ja ajattelu

This study explores ecumenical activity of professor and bishop E. G. Gulin (1893 1975). Gulin was one of the key figures in the Finland s Evangelical Lutheran Church during the twentieth century. He was also one of the leading persons who imported ecumenical influences from abroad. However, unlike other churches, the Church of Finland did not recognise his importance. For example, in the 1950s Gulin was seen by the Anglicans as a future archbishop for the Evangelical Lutheran Church of Finland. Gulin s career as an ecumenist can be divided to three parts. Between 1917 and 1929, Gulin learned ecumenical working methods in Finland s World Student Christian Federation. He had a background in the revivalist movement, and his parents supported him in his studies. The Evangelical Lutheran Church did not originally play a major role for Gulin, although he was a member. Between 1930 and 1944, Gulin had more and more responsibility as a leading ecumenist in Finland. He became a member of Finland s ecumenical board, Yleiskirkollinen toimikunta. During the Second World War Gulin tried to solicit assistance for Finland s war effort at theological conferences, where Finnish theologians often discussed cooperation among Christians. A third period started in 1945, when Gulin became the bishop of Tampere. His new status in the Evangelical Lutheran Church placed him in a challenging position in ecumenical questions. He had responsibility for inter-church aid in Finland. He also participated in the World Council of Churches (WCC) assemblies in Evanston in 1954 and in New Delhi in 1961. Gulin s role was quite insignificant in those meetings. Closely related to Gulin s texts about ecumenism is kokemus, experience. Gulin wrote about his ecumenical experience or ekumeeninen kokemus. He believed that it was vital for the churches to appreciate their own experiences, since experience was the basis for further development. Yet Gulin mentioned very little about Christian dogma. The main reason seems to have been that he did not believe that a union between churches could be built on dogma.

Theological Exegesis in the Canonical Context : Brevard S. Childs' Methodology of Biblical Theology

Modern Christian theology has been at pain with the schism between the Bible and theology, and between biblical studies and systematic theology. Brevard Springs Childs is one of biblical scholars who attempt to dismiss this “iron curtain” separating the two disciplines. The present thesis aims at analyzing Childs’ concept of theological exegesis in the canonical context. In the present study I employ the method of systematic analysis. The thesis consists of seven chapters. Introduction is the first chapter. The second chapter attempts to find out the most important elements which exercise influence on Childs’ methodology of biblical theology by sketching his academic development during his career. The third chapter attempts to deal with the crucial question why and how the concept of the canon is so important for Childs’ methodology of biblical theology. In chapter four I analyze why and how Childs is dissatisfied with historical-critical scholarship and I point out the differences and similarities between his canonical approach and historical criticism. The fifth chapter attempts at discussing Childs’ central concepts of theological exegesis by investigating whether a Christocentric approach is an appropriate way of creating a unified biblical theology. In the sixth chapter I present a critical evaluation and methodological reflection of Childs’ theological exegesis in the canonical context. The final chapter sums up the key points of Childs’ methodology of biblical theology. The basic results of this thesis are as follows: First, the fundamental elements of Childs’ theological thinking are rooted in Reformed theological tradition and in modern theological neo-orthodoxy and in its most prominent theologian, Karl Barth. The American Biblical Theological Movement and the controversy between Protestant liberalism and conservatism in the modern American context cultivate his theological sensitivity and position. Second, Childs attempts to dismiss negative influences of the historical-critical method by establishing canon-based theological exegesis leading into confessional biblical theology. Childs employs terminology such as canonical intentionality, the wholeness of the canon, the canon as the most appropriate context for doing a biblical theology, and the continuity of the two Testaments, in order to put into effect his canonical program. Childs demonstrates forcefully the inadequacies of the historical-critical method in creating biblical theology in biblical hermeneutics, doctrinal theology, and pastoral practice. His canonical approach endeavors to establish and create post-critical Christian biblical theology, and works within the traditional framework of faith seeking understanding. Third, Childs’ biblical theology has a double task: descriptive and constructive, the former connects biblical theology with exegesis, the later with dogmatic theology. He attempts to use a comprehensive model, which combines a thematic investigation of the essential theological contents of the Bible with a systematic analysis of the contents of the Christian faith. Childs also attempts to unite Old Testament theology and New Testament theology into one unified biblical theology. Fourth, some problematic points of Childs’ thinking need to be mentioned. For instance, his emphasis on the final form of the text of the biblical canon is highly controversial, yet Childs firmly believes in it, he even regards it as the corner stone of his biblical theology. The relationship between the canon and the doctrine of biblical inspiration is weak. He does not clearly define whether Scripture is God’s word or whether it only “witnesses” to it. Childs’ concepts of “the word of God” and “divine revelation” remain unclear, and their ontological status is ambiguous. Childs’ theological exegesis in the canonical context is a new attempt in the modern history of Christian theology. It expresses his sincere effort to create a path for doing biblical theology. Certainly, it was just a modest beginning of a long process.

Small State Cultures of Consensus : State Traditions and Consensus-Seeking in the Neo-Corporatist and Neutrality Policies in Post-1945 Austria and Finland

Austria and Finland are persistently referred to as the “success stories” of post-1945 European history. Notwithstanding their different points of departure, in the course of the Cold War both countries portrayed themselves as small and neutral border-states in the world dictated by superpower politics. By the 1970s, both countries frequently ranked at the top end in various international classifications regarding economic development and well-being in society. This trend continues today. The study takes under scrutiny the concept of consensus which figures centrally in the two national narratives of post-1945 success. Given that the two domestic contexts as such only share few direct links with one another and are more obviously different than similar in terms of their geographical location, historical experiences and politico-cultural traditions, the analogies and variations in the anatomies of the post-1945 “cultures of consensus” provide an interesting topic for a historical comparative and cross-national examination. The main research question concerns the identification and analysis of the conceptual and procedural convergence points of the concepts of the state and consensus. The thesis is divided into six main chapters. After the introduction, the second chapter presents the theoretical framework in more detail by focusing on the key concepts of the study – the state and consensus. Chapter two also introduces the comparative historical and cross-national research angles. Chapter three grounds the key concepts of the state and consensus in the historical contexts of Austria and Finland by discussing the state, the nation and democracy in a longer term comparative perspective. The fourth and fifth chapter present case studies on the two policy fields, the “pillars”, upon which the post-1945 Austrian and Finnish cultures of consensus are argued to have rested. Chapter four deals with neo-corporatist features in the economic policy making and chapter five discusses the building up of domestic consensus regarding the key concepts of neutrality policies in the 1950s and 1960s. The study concludes that it was not consensus as such but the strikingly intense preoccupation with the theme of domestic consensus that cross-cut, in a curiously analogous manner, the policy-making processes studied. The main challenge for the post-1945 architects of Austrian and Finnish cultures of consensus was to find strategies and concepts for consensus-building which would be compatible with the principles of democracy. Discussed at the level of procedures, the most important finding of the study concerns the triangular mechanism of coordination, consultation and cooperation that set into motion and facilitated a new type of search for consensus in both post-war societies. In this triangle, the agency of the state was central, though in varying ways. The new conceptions concerning a small state’s position in the Cold War world also prompted cross-nationally perceivable willingness to reconsider inherited concepts and procedures of the state and the nation. At the same time, the ways of understanding the role of the state and its relation to society remained profoundly different in Austria and Finland and this basic difference was in many ways reflected in the concepts and procedures deployed in the search for consensus and management of domestic conflicts. For more detailed information, please consult the author.

Essays on Economic Integration and Labour Demand

This dissertation consists of an introductory section and three essays investigating the effects of economic integration on labour demand by using theoretical models and by empirical analysis. The essays adopt an intra-industry trade approach to specify a theoretical framework of estimation for determining the effects of economic integration on employment. In all the essays the empirical aim is to explore the labour demand consequences of European integration. The first essay analyzes how labour-demand elasticities with own price have changed during the process of economic integration. As a theoretical result, intensified trade competition increases labour-demand elasticity, whereas better advantage of economies of scale decreases labour-demand elasticity by decreasing the elasticity of substitution between differentiated products. Furthermore, if integration gives rise to an increase in input-substitutability and/or outsourcing activities, labour demand will become more elastic. Using data from the manufacturing sector from 1975 to 2002, the empirical results provide support for the hypothesis that European integration has contributed to increased elasticities of total labour demand in Finland. The second essay analyzes how economic integration affects the impact of welfare poli-cies on employment. The essay considers the viability of financing the public sector, i.e. public consumption and social security expenses, by general labour taxation in an economy which has become more integrated into international product markets. The theoretical results of the second essay indicate that, as increased trade competition crowds out better economies of scale, it becomes more costly to maintain welfare systems financed by labour taxation. Using data from European countries for the years 1975 to 2004, the empirical results provide inconsistent evidence for the hypothesis that economic integration has contributed to the distortion effects of welfare policies on employment. The third essay analyzes the impact of profit sharing on employment as a way to introduce wage flexibility into the process of economic integration. The results of the essay suggest that, in theory, the effects of economic integration on the impact of profit sharing on employment clearly depend on a trade-off between intensified competition and better advantage of economies of scale. If product market competition increases, the ability of profit sharing to improve employment through economic integration increases with moderated wages. While, the economic integration associating with market power in turn decrease the possibilities of profit sharing with higher wages to improve employment. Using data from the manufacturing sector for the years 1996 to 2004, the empirical results show that profit-sharing has a positive impact on employment during the process of European integration, but can have ambiguous effects on the stability of employment in Finland.

Socialist Realism instead of Formalism : the Formation and Development of the Soviet Music Control System 1932-1950

Whereas it has been widely assumed in the public that the Soviet music policy system had a “top-down” structure of control and command that directly affected musical creativity, in fact my research shows that the relations between the different levels of the music policy system were vague, and the viewpoints of its representatives differed from each other. Because the representatives of the party and government organs controlling operas could not define which kind of music represented Socialist Realism, the system as it developed during the 1930s and 1940s did not function effectively enough in order to create such a centralised control of Soviet music, still less could Soviet operas fulfil the highly ambiguous aesthetics of Socialist Realism. I show that musical discussions developed as bureaucratic ritualistic arenas, where it became more important to reveal the heretical composers, making scapegoats of them, and requiring them to perform self-criticism, than to give directions on how to reach the artistic goals of Socialist Realism. When one opera was found to be unacceptable, this lead to a strengthening of control by the party leadership, which lead to more operas, one after the other, to be revealed as failures. I have studied the control of the composition, staging and reception of the opera case-studies, which remain obscure in the West despite a growing scholarly interest in them, and have created a detailed picture of the foundation and development of the Soviet music control system in 1932-1950. My detailed discussion of such case-studies as Ivan Dzerzhinskii’s The Quiet Don, Dmitrii Shostakovich’s Lady Macbeth of Mtsensk District, Vano Muradeli’s The Great Friendship, Sergei Prokofiev’s Story of a Real Man, Tikhon Khrennikov’s Frol Skobeev and Evgenii Zhukovskii’s From All One’s Heart backs with documentary precision the historically revisionist model of the development of Soviet music. In February 1948, composers belonging to the elite of the Union of Soviet Composers, e.g. Dmitri Shostakovich and Sergei Prokofiev, were accused in a Central Committee Resolution of formalism, as been under the influence of western modernism. Accusations of formalism were connected to the criticism of the conciderable financial, material and social privileges these composers enjoyed in the leadership of the Union. With my new archival findings I give a more detailed picture of the financial background for the 1948 campaign. The independent position of the music funding organization of the Union of Soviet Composers (Muzfond) to decide on its finances was an exceptional phenomenon in the Soviet Union and contradicted the strivings to strengthen the control of Soviet music. The financial audits of the Union of Soviet Composers did not, however, change the elite status of some of its composers, except for maybe a short duration in some cases. At the same time the independence of the significal financial authorities of Soviet theatres was restricted. The cuts in the governmental funding allocated to Soviet theatres contradicted the intensified ideological demands for Soviet operas.

Do Measurement Errors in GDP Announcements Cause Output Fluctuations?

This thesis studies empirically whether measurement errors in aggregate production statistics affect sentiment and future output. Initial announcements of aggregate production are subject to measurement error, because many of the data required to compile the statistics are produced with a lag. This measurement error can be gauged as the difference between the latest revised statistic and its initial announcement. Assuming aggregate production statistics help forecast future aggregate production, these measurement errors are expected to affect macroeconomic forecasts. Assuming agents’ macroeconomic forecasts affect their production choices, these measurement errors should affect future output through sentiment. This thesis is primarily empirical, so the theoretical basis, strategic complementarity, is discussed quite briefly. However, it is a model in which higher aggregate production increases each agent’s incentive to produce. In this circumstance a statistical announcement which suggests aggregate production is high would increase each agent’s incentive to produce, thus resulting in higher aggregate production. In this way the existence of strategic complementarity provides the theoretical basis for output fluctuations caused by measurement mistakes in aggregate production statistics. Previous empirical studies suggest that measurement errors in gross national product affect future aggregate production in the United States. Additionally it has been demonstrated that measurement errors in the Index of Leading Indicators affect forecasts by professional economists as well as future industrial production in the United States. This thesis aims to verify the applicability of these findings to other countries, as well as study the link between measurement errors in gross domestic product and sentiment. This thesis explores the relationship between measurement errors in gross domestic production and sentiment and future output. Professional forecasts and consumer sentiment in the United States and Finland, as well as producer sentiment in Finland, are used as the measures of sentiment. Using statistical techniques it is found that measurement errors in gross domestic product affect forecasts and producer sentiment. The effect on consumer sentiment is ambiguous. The relationship between measurement errors and future output is explored using data from Finland, United States, United Kingdom, New Zealand and Sweden. It is found that measurement errors have affected aggregate production or investment in Finland, United States, United Kingdom and Sweden. Specifically, it was found that overly optimistic statistics announcements are associated with higher output and vice versa.

Molecular Tuning of Rhodopsins for High Visual Sensitivity in Different Light Environments : Variation in Absorbance Spectrum and Opsin Sequence within and between Species

Visual pigments of different animal species must have evolved at some stage to match the prevailing light environments, since all visual functions depend on their ability to absorb available photons and transduce the event into a reliable neural signal. There is a large literature on correlation between the light environment and spectral sensitivity between different fish species. However, little work has been done on evolutionary adaptation between separated populations within species. More generally, little is known about the rate of evolutionary adaptation to changing spectral environments. The objective of this thesis is to illuminate the constraints under which the evolutionary tuning of visual pigments works as evident in: scope, tempo, available molecular routes, and signal/noise trade-offs. Aquatic environments offer Nature s own laboratories for research on visual pigment properties, as naturally occurring light environments offer an enormous range of variation in both spectral composition and intensity. The present thesis focuses on the visual pigments that serve dim-light vision in two groups of model species, teleost fishes and mysid crustaceans. The geographical emphasis is in the brackish Baltic Sea area with its well-known postglacial isolation history and its aquatic fauna of both marine and fresh-water origin. The absorbance spectrum of the (single) dim-light visual pigment were recorded by microspectrophotometry (MSP) in single rods of 26 fish species and single rhabdoms of 8 opossum shrimp populations of the genus Mysis inhabiting marine, brackish or freshwater environments. Additionally, spectral sensitivity was determined from six Mysis populations by electroretinogram (ERG) recording. The rod opsin gene was sequenced in individuals of four allopatric populations of the sand goby (Pomatoschistus minutus). Rod opsins of two other goby species were investigated as outgroups for comparison. Rod absorbance spectra of the Baltic subspecies or populations of the primarily marine species herring (Clupea harengus membras), sand goby (P. minutus), and flounder (Platichthys flesus) were long-wavelength-shifted compared to their marine populations. The spectral shifts are consistent with adaptation for improved quantum catch (QC) as well as improved signal-to-noise ratio (SNR) of vision in the Baltic light environment. Since the chromophore of the pigment was pure A1 in all cases, this has apparently been achieved by evolutionary tuning of the opsin visual pigment. By contrast, no opsin-based differences were evident between lake and sea populations of species of fresh-water origin, which can tune their pigment by varying chromophore ratios. A more detailed analysis of differences in absorbance spectra and opsin sequence between and within populations was conducted using the sand goby as model species. Four allopatric populations from the Baltic Sea (B), Swedish west coast (S), English Channel (E), and Adriatic Sea (A) were examined. Rod absorbance spectra, characterized by the wavelength of maximum absorbance (λmax), differed between populations and correlated with differences in the spectral light transmission of the respective water bodies. The greatest λmax shift as well as the greatest opsin sequence difference was between the Baltic and the Adriatic populations. The significant within-population variation of the Baltic λmax values (506-511 nm) was analyzed on the level of individuals and was shown to correlate well with opsin sequence substitutions. The sequences of individuals with λmax at shorter wavelengths were identical to that of the Swedish population, whereas those with λmax at longer wavelengths additionally had substitution F261F/Y in the sixth transmembrane helix of the protein. This substitution (Y261) was also present in the Baltic common gobies and is known to redshift spectra. The tuning mechanism of the long-wavelength type Baltic sand gobies is assumed to be the co-expression of F261 and Y261 in all rods to produce ≈ 5 nm redshift. The polymorphism of the Baltic sand goby population possibly indicates ambiguous selection pressures in the Baltic Sea. The visual pigments of all lake populations of the opossum shrimp (Mysis relicta) were red-shifted by 25 nm compared with all Baltic Sea populations. This is calculated to confer a significant advantage in both QC and SNR in many humus-rich lakes with reddish water. Since only A2 chromophore was present, the differences obviously reflect evolutionary tuning of the visual protein, the opsin. The changes have occurred within the ca. 9000 years that the lakes have been isolated from the Sea after the most recent glaciation. At present, it seems that the mechanism explaining the spectral differences between lake and sea populations is not an amino acid substitution at any other conventional tuning site, but the mechanism is yet to be found.

Phylogenetics, taxon delimitation and phylogenetic diversity

Throughout the history of Linnean taxonomy, species have been described with varying degrees of justification. Many descriptions have been based on only a few ambiguous morphological characters. Moreover, species have been considered natural, well-defined units whereas higher taxa have been treated as disparate, non-existent creations. In the present thesis a few such cases were studied in detail. Often the species-level descriptions were based on only a few specimens and the variation previously thought to be interspecific was found to be intraspecific. In some cases morphological characters were sufficient to resolve the evolutionary relationships between the taxa, but generally more resolution was gained by the addition of molecular evidence. However, both morphological and molecular data were found to be deceptive in some cases. The DNA sequences of morphologically similar specimens were found to differ distinctly in some cases, whereas in other closely related species the morphology of specimens with identical DNA sequences differed substantially. This study counsels caution when evolutionary relationships are being studied utilizing only one source of evidence or a very limited number of characters (e.g. barcoding). Moreover, it emphasizes the importance of high quality data as well as the utilization of proper methods when making scientific inferences. Properly conducted analyses produce robust results that can be utilized in numerous interesting ways. The present thesis considered two such extensions of systematics. A novel hypothesis on the origin of bioluminescence in Elateriformia beetles is presented, tying it to the development of the clicking mechanism in the ancestors of these animals. An entirely different type of extension of systematics is the proposed high value of the white sand forests in maintaining the diversity of beetles in the Peruvian Amazon. White sand forests are under growing pressure from human activities that lead to deforestation. They were found to harbor an extremely diverse beetle fauna and many taxa were specialists living only in this unique habitat. In comparison to the predominant clay soil forests, considerably more elateroid beetles belonging to all studied taxonomic levels (species, genus, tribus, and subfamily) were collected in white sand forests. This evolutionary diversity is hypothesized to be due to a combination of factors: (1) the forest structure, which favors the fungus-plant interactions important for the elateroid beetles, (2) the old age of the forest type favoring survival of many evolutionary lineages and (3) the widespread distribution and fragmentation of the forests in the Miocene, favoring speciation.

Analyzing changes in macro-level drivers of country-specific emissions : The role of consumption, technology and trade

Industrial ecology is an important field of sustainability science. It can be applied to study environmental problems in a policy relevant manner. Industrial ecology uses ecosystem analogy; it aims at closing the loop of materials and substances and at the same time reducing resource consumption and environmental emissions. Emissions from human activities are related to human interference in material cycles. Carbon (C), nitrogen (N) and phosphorus (P) are essential elements for all living organisms, but in excess have negative environmental impacts, such as climate change (CO2, CH4 N2O), acidification (NOx) and eutrophication (N, P). Several indirect macro-level drivers affect emissions change. Population and affluence (GDP/capita) often act as upward drivers for emissions. Technology, as emissions per service used, and consumption, as economic intensity of use, may act as drivers resulting in a reduction in emissions. In addition, the development of country-specific emissions is affected by international trade. The aim of this study was to analyse changes in emissions as affected by macro-level drivers in different European case studies. ImPACT decomposition analysis (IPAT identity) was applied as a method in papers I III. The macro-level perspective was applied to evaluate CO2 emission reduction targets (paper II) and the sharing of greenhouse gas emission reduction targets (paper IV) in the European Union (EU27) up to the year 2020. Data for the study were mainly gathered from official statistics. In all cases, the results were discussed from an environmental policy perspective. The development of nitrogen oxide (NOx) emissions was analysed in the Finnish energy sector during a long time period, 1950 2003 (paper I). Finnish emissions of NOx began to decrease in the 1980s as the progress in technology in terms of NOx/energy curbed the impact of the growth in affluence and population. Carbon dioxide (CO2) emissions related to energy use during 1993 2004 (paper II) were analysed by country and region within the European Union. Considering energy-based CO2 emissions in the European Union, dematerialization and decarbonisation did occur, but not sufficiently to offset population growth and the rapidly increasing affluence during 1993 2004. The development of nitrogen and phosphorus load from aquaculture in relation to salmonid consumption in Finland during 1980 2007 was examined, including international trade in the analysis (paper III). A regional environmental issue, eutrophication of the Baltic Sea, and a marginal, yet locally important source of nutrients was used as a case. Nutrient emissions from Finnish aquaculture decreased from the 1990s onwards: although population, affluence and salmonid consumption steadily increased, aquaculture technology improved and the relative share of imported salmonids increased. According to the sustainability challenge in industrial ecology, the environmental impact of the growing population size and affluence should be compensated by improvements in technology (emissions/service used) and with dematerialisation. In the studied cases, the emission intensity of energy production could be lowered for NOx by cleaning the exhaust gases. Reorganization of the structure of energy production as well as technological innovations will be essential in lowering the emissions of both CO2 and NOx. Regarding the intensity of energy use, making the combustion of fuels more efficient and reducing energy use are essential. In reducing nutrient emissions from Finnish aquaculture to the Baltic Sea (paper III) through technology, limits of biological and physical properties of cultured fish, among others, will eventually be faced. Regarding consumption, salmonids are preferred to many other protein sources. Regarding trade, increasing the proportion of imports will outsource the impacts. Besides improving technology and dematerialization, other viewpoints may also be needed. Reducing the total amount of nutrients cycling in energy systems and eventually contributing to NOx emissions needs to be emphasized. Considering aquaculture emissions, nutrient cycles can be partly closed through using local fish as feed replacing imported feed. In particular, the reduction of CO2 emissions in the future is a very challenging task when considering the necessary rates of dematerialisation and decarbonisation (paper II). Climate change mitigation may have to focus on other greenhouse gases than CO2 and on the potential role of biomass as a carbon sink, among others. The global population is growing and scaling up the environmental impact. Population issues and growing affluence must be considered when discussing emission reductions. Climate policy has only very recently had an influence on emissions, and strong actions are now called for climate change mitigation. Environmental policies in general must cover all the regions related to production and impacts in order to avoid outsourcing of emissions and leakage effects. The macro-level drivers affecting changes in emissions can be identified with the ImPACT framework. Statistics for generally known macro-indicators are currently relatively well available for different countries, and the method is transparent. In the papers included in this study, a similar method was successfully applied in different types of case studies. Using transparent macro-level figures and a simple top-down approach are also appropriate in evaluating and setting international emission reduction targets, as demonstrated in papers II and IV. The projected rates of population and affluence growth are especially worth consideration in setting targets. However, sensitivities in calculations must be carefully acknowledged. In the basic form of the ImPACT model, the economic intensity of consumption and emission intensity of use are included. In seeking to examine consumption but also international trade in more detail, imports were included in paper III. This example demonstrates well how outsourcing of production influences domestic emissions. Country-specific production-based emissions have often been used in similar decomposition analyses. Nevertheless, trade-related issues must not be ignored.

Mitä hyötyä tehohoidosta? : Tehohoitoa sisältäneiden hoitojaksojen vaikuttavuuden arviointi

Intensive care is to be provided to patients benefiting from it, in an ethical, efficient, effective and cost-effective manner. This implies a long-term qualitative and quantitative analysis of intensive care procedures and related resources. The study population consists of 2709 patients treated in the general intensive care unit (ICU) of Helsinki University Hospital. Study sectors investigate intensive care patients mortality, quality of life (QOL), Quality-Adjusted Life-Years (QALY units) and factors related to severity of illness, length of stay (LOS), patient s age, evaluation period as well as experiences and memories connected with the ICU episode. In addition, the study examines the qualities of two QOL measures, the RAND 36 Item Health Survey 1.0 (RAND-36) and the 5 Item EuroQol-5D (EQ-5D) and assesses the correlation of the test results. Patients treated in 1995 responded to the RAND-36 questionnaire in 1996. All patients, treated from 1995-2000, received a QOL questionnaires in 2001, when 1 7 years had lapsed from the intensive treatment. Response rate was 79.5 %. Main Results 1) Of the patients who died within the first year (n = 1047) 66 % died during the intensive care period or within the following month. The non-survivors were more aged than the surviving patients, had generally a higher than average APACHE II and SOFA score depicting the severity of illness, their ICU LOS was longer and hospital stay shorter than of the surviving patients (p < 0.001). Mortality of patients receiving conservative treatment was higher than of those receiving surgical treatment. Patients replying to the QOL survey in 2001 (n = 1099) had recovered well: 97 % of those lived at home. More than half considered their QOL as good or extremely good, 40 % as satisfactory and 7 % as bad. All QOL indexes of those of working-age were considerably lower (p < 0.001) than comparable figures of the age- and gender-adjusted Finnish population. The 5-year monitoring period made evident that mental recovery was slower than physical recovery. 2) The results of RAND-36 and EQ-5D correlated well (p < 0.01). The RAND-36 profile measure distinguished more clearly between the different categories of QOL and their levels. EQ-5D measured well the patient groups general QOL and the sum index was used to calculate QALY units. 3) QALY units were calculated by multiplying the time the patient survived after ICU stay or expected life-years by the EQ-5D sum index. Aging automatically lowers the number of QALY units. Patients under the age of 65 receiving conservative treatment benefited from treatment to a greater extent measured in QALY units than their peers receiving surgical treatment, but in the age group 65 and over patients with surgical treatment received higher QALY ratings than recipients of conservative treatment. 4) The intensive care experience and QOL ratings were connected. The QOL indices were statistically highest for those recipients with memories of intensive care as a positive experience, albeit their illness requiring intensive care treatment was less serious than average. No statistically significant differences were found in the QOL indices of those with negative memories, no memories or those who did not express the quality of their experiences.

Comparison and integration of MEG and fMRI

MEG directly measures the neuronal events and has greater temporal resolution than fMRI, which has limited temporal resolution mainly due to the larger timescale of the hemodynamic response. On the other hand fMRI has advantages in spatial resolution, while the localization results with MEG can be ambiguous due to the non-uniqueness of the electromagnetic inverse problem. Thus, these methods could provide complementary information and could be used to create both spatially and temporally accurate models of brain function. We investigated the degree of overlap, revealed by the two imaging methods, in areas involved in sensory or motor processing in healthy subjects and neurosurgical patients. Furthermore, we used the spatial information from fMRI to construct a spatiotemporal model of the MEG data in order to investigate the sensorimotor system and to create a spatiotemporal model of its function. We compared the localization results from the MEG and fMRI with invasive electrophysiological cortical mapping. We used a recently introduced method, contextual clustering, for hypothesis testing of fMRI data and assessed the the effect of neighbourhood information use on the reproducibility of fMRI results. Using MEG, we identified the ipsilateral primary sensorimotor cortex (SMI) as a novel source area contributing to the somatosensory evoked fields (SEF) to median nerve stimulation. Using combined MEG and fMRI measurements we found that two separate areas in the lateral fissure may be the generators for the SEF responses from the secondary somatosensory cortex region. The two imaging methods indicated activation in corresponding locations. By using complementary information from MEG and fMRI we established a spatiotemporal model of somatosensory cortical processing. This spatiotemporal model of cerebral activity was in good agreement with results from several studies using invasive electrophysiological measurements and with anatomical studies in monkey and man concerning the connections between somatosensory areas. In neurosurgical patients, the MEG dipole model turned out to be more reliable than fMRI in the identification of the central sulcus. This was due to prominent activation in non-primary areas in fMRI, which in some cases led to erroneous or ambiguous localization of the central sulcus.

Studies on the Cell Wall Structure and on the Mechanical Properties of Norway Spruce

The structure and the mechanical properties of wood of Norway spruce (Picea abies [L.] Karst.) were studied using small samples from Finland and Sweden. X-ray diffraction (XRD) was used to determine the orientation of cellulose microfibrils (microfibril angle, MFA), the dimensions of cellulose crystallites and the average shape of the cell cross-section. X-ray attenuation and x-ray fluorescence measurements were used to study the chemical composition and the trace element content. Tensile testing with in situ XRD was used to characterise the mechanical properties of wood and the deformation of crystalline cellulose within the wood cell walls. Cellulose crystallites were found to be 192 284 Å long and 28.9 33.4 Å wide in chemically untreated wood and they were longer and wider in mature wood than in juvenile wood. The MFA distribution of individual Norway spruce tracheids and larger samples was asymmetric. In individual cell walls, the mean MFA was 19 30 degrees, while the mode of the MFA distribution was 7 21 degrees. Both the mean MFA and the mode of the MFA distribution decreased as a function of the annual ring. Tangential cell walls exhibited smaller mean MFA and mode of the MFA distribution than radial cell walls. Maceration of wood material caused narrowing of the MFA distribution and removed contributions observed at around 90 degrees. In wood of both untreated and fertilised trees, the average shape of the cell cross-section changed from circular via ambiguous to rectangular as the cambial age increased. The average shape of the cell cross-section and the MFA distribution did not change as a result of fertilisation. The mass absorption coefficient for x-rays was higher in wood of fertilised trees than in that of untreated trees and wood of fertilised trees contained more of the elements S, Cl, and K, but a smaller amount of Mn. Cellulose crystallites were longer in wood of fertilised trees than in that of untreated trees. Kraft cooking caused widening and shortening of the cellulose crystallites. Tensile tests parallel to the cells showed that if the mean MFA is initially around 10 degrees or smaller, no systematic changes occur in the MFA distribution due to strain. The role of mean MFA in defining the tensile strength or the modulus of elasticity of wood was not as dominant as that reported earlier. Crystalline cellulose elongated much less than the entire samples. The Poisson ratio νca of crystalline cellulose in Norway spruce wood was shown to be largely dependent on the surroundings of crystalline cellulose in the cell wall, varying between -1.2 and 0.8. The Poisson ratio was negative in kraft cooked wood and positive in chemically untreated wood. In chemically untreated wood, νca was larger in mature wood and in latewood compared to juvenile wood and earlywood.