Structural and optical characterization of Zn1-xCdxO thin films deposited by dc reactive magnetron sputtering

Zn1-xCdxO crystal thin films with different compositions were prepared on silicon and sapphire substrates by the dc reactive magnetron sputtering technique. X-ray diffraction measurements show that the Zn1-xCdxO films are of completely (002)-preferred orientation for x less than or equal to 0.6. For x = 0.8, the Elm is a mixture of ZnO hexagonal wurtzite crystals and CdO cubic crystals. For pure CdO, it is highly (200) preferential-oriented. Photoluminescence spectrum measurement shows that the Zn1-xCdxO (x = 0.2) thin film has a redshift of 0.14 eV from that of ZnO reported previously.

Photoluminescence of nanocrystalline SiC films prepared by rf magnetron sputtering

Amorphous Sic films are deposited on Si (111) substrates by rf magnetron sputtering and then annealed at 1200 degreesC for different times by a dc self-heating method in a vacuum annealing system. The crystallization of the amorphous Sic is determined by Raman scattering at room temperature and X-ray diffraction. The experimental result indicates that the Sic nanocrystals have formed in the films. The topography of the as-annealed films is characterized by atomic force microscopy. Measurements of photoluminescence of the as-annealed films show blue or violet light emission from the nanocrystalline Sic films and photoluminescence peak shifts to short wavelength side as the annealing time decreases.

Sputtering of ZnO buffer layer on Si for GaN blue light emitting materials

The preparation of high quality ZnO/Si substrates for the growth of GaN blue light emitting materials is considered. ZnO thin films have been deposited on Si(100) and Si(lll) substrates by conventional magnetron sputtering. Morphology, crystallinity and c-axis preferred orientation of ZnO thin films have been investigated by transmitting electron microscopy (TEM), X-ray diffraction (XRD) and X-ray rocking curve (XRC). It is proved that the ZnO thin films have perfect structure. The full-width-at-half-maximum (FWHM) of the ZnO(002) XRC of these films is about 1 degrees, while the minimum is 0.353 degrees. This result is better than the minimum FWHM (about 2 degrees) reported by other research groups. Moreover, comparison and discussion are given on film structure of ZnO/Si(100) and ZnO/Si(lll).

p-type co-doping study of GaN by photoluminescence

Photoluminescence measurements were performed on p-type co-doping effects of C, As, and Mg in GaN. The dopants were incorporated into GaN by ion implantation performed at 77 K. We find that the 3.42 eV luminescence line is sensitive to hole concentration, and propose that after cartful calibration the 3.42 eV line may be used as a probe to measure hole concentration in GaN. Simply doping one kind of accepters will not result in holes, while co-doping can substantially improve p-type doping efficiency. As + C and As + Mg co-doping induce an acceptor level of 180 meV above the valence band. Mg + C co-doping is the most promising method for p-type doping, the related acceptor level is determined to be as shallow as 130 meV. The improvement of the doping efficiency by co-doping is probably due to the decrease of the acceptor ionization energy. (C) 1999 Elsevier Science B.V. All rights reserved.

Fabrication of Nano-structured VOx Film by Low Temperature Ion Beam Sputtering and Reductive Annealing

VOx thin films have been fabricated by low temperature ion beam sputtering and post reductive annealing process. Semiconductor-metal phase transition is observed for the film annealed at 400 degrees C for 2 hours. The film also shows a polycrystal structure with grain size from 50nm to 150nm. The VOx thin films fabricated by this process have a TCR up to -2.7% at room temperature. Our results indicate a promising fabrication method of the nano-structured VOx film with relatively high TCR and semiconductor-metal phase transition.

The difference of Si doping efficiency in GaN and AlGaN in GaN-based HBT structure

An AlGaN/GaN HBT structure was grown by low-pressure metalorganic chemical vapor deposition (MOCVD) on sapphire substrate. From the high-resolution x-ray diffraction and transmission electron microscopy (TEM) measurements, it was indicated that the structure is of good quality and the AlGaN/GaN interfaces are abrupt and smooth. In order to obtain the values of Si doping and electronic concentrations in the AlGaN emitter and GaN emitter cap layers, Secondary Ion Mass Spectroscopy (SIMS) and electrochemical CV measurements were carried out. The results showed that though the flow rate of silane (SiH4) in growing the AlGaN emitter was about a quarter of that in growing GaN emitter cap and subcollector layer, the Si sputtering yield in GaN cap layer was much smaller than that in the AlGaN emitter layer. The electronic concentration in GaN was about half of that in the AlGaN emitter layer. It is proposed that the Si, Al co-doping in growing the AlGaN emitter layer greatly enhances the Si dopant efficiency in the AlGaN alloy. (c) 2006 WILEY-VCH Verlag GmbH & Co KGaA, Weinheim.

Structural and magnetic properties of GaN:Sm:Eu films fabricated by co-implantation method

Diluted-magnetic GaN:Sm:Eu films have been fabricated by co-implantation of Sm and Eu ions into c-plane (0001) GaN films and a subsequent annealing process. The structural, morphological and magnetic characteristics of the samples have been investigated by means of high-resolution X-ray diffraction (HRXRD), atomic force microscopy (AFM), and superconducting quantum interference device (SQUID). The XRD and AFM analyses show that the annealing process can effectively recover the crystalline degradation caused by implantation. Compared with GaN:Sm films, more defects have been introduced into GaN:Sm:Eu films due to the Eu implantation process. According to the SQUID analysis, GaN:Sm:Eu films exhibit clear room-temperature ferromagnetism. Moreover, GaN:Sm:Eu films show a lower saturation magnetization (Ms) than GaN:Sm films.

Web Services Workflows—Composition, Co-Ordination, and Transactions in Service-Oriented Computing

Web services can be seen as a newly emerging research area for Service-oriented Computing and their implementation in Service-oriented Architectures. Web services are self-contained, self-describing modular applications or components providing services. Web services may be dynamically aggregated, composed, and enacted as Web services Workflows. This requires frameworks and interaction protocols for their co-ordination and transaction support. In a Service-oriented Computing setting, transactions are more complex, involve multiple parties (roles), span many organizations, and may be long-running, consisting of a highly decentralized service partner and performed by autonomous entities. A Service-oriented Transaction Model has to provide comprehensive support for long-running propositions including negotiations, conversations, commitments, contracts, tracking, payments, and exception handling. Current transaction models and mechanisms including their protocols and primitives do not sufficiently cater for quality-aware and long running transactions comprising loosely-coupled (federated) service partners and resources. Web services transactions require co-ordination behavior provided by a traditional transaction mechanism to control the operations and outcome of an application. Furthermore, Web services transactions require the capability to handle the co-ordination of processing outcomes or results from multiple services in a more flexible manner. This requires more relaxed forms of transactions—those that do not strictly have to abide by the ACID properties—such as loosely-coupled collaboration and workflows. Furthermore, there is a need to group Web services into applications that require some form of correlation, but do not necessarily require transactional behavior. The purpose of this paper is to provide a state-of-the-art review and overview of some proposed standards surrounding Web services composition, co-ordination, and transaction. In particular the Business Process Execution Language for Web services (BPEL4WS), its co-ordination, and transaction frameworks (WS-Co-ordination and WS-Transaction) are discussed.

co-creativepen toolkit: a pen-based 3d toolkit for children cooperatly designing virtual environment

Co-CreativePen Toolkit is a pen-based 3D toolkit for children cooperatly designing virtual environment. This toolkit is used to construct different applications involved with distributedpen-based 3D interaction. In this toolkit,sketch method is encapsulated as kinds of interaction techniques. Children can use pen to construct 3D and IBR objects, to navigate in the virtual world, to select and manipulate virtual objects, and to communicate with other children. Children can use pen to select other children in the virtual world, and use pen to write message to children selected The distributed architecture of Co-CreativePen Toolkit is based on the CORBA. A common scene graph is managed in the server with several copies of this graph are managed in every client.Every changes of the scene graph in client will cause the change in the server and other client.