Phase-locked ring-defect photonic crystal vertical-cavity surface-emitting laser

Phase-locked oxide-confined ring-defect photonic crystal vertical-cavity surface-emitting laser is presented. The coupled-mode theory is employed to illustrate the two supermodes of the device, in-phase and out-of-phase supermode. Experimental results verify the two supermodes by the characteristics of the spectra and the far field patterns. At the lower current, only the out-of-phase supermode is excited, whereas under the higher current, the in-phase supermode also appears at the shorter wavelength range. In addition, the measured spectral separation between the two supermodes agrees well with the theoretical result.

Room temperature operation of photonic-crystal distributed-feedback quantum cascade lasers with single longitudinal and lateral mode performance

We demonstrate room temperature operation of photonic-crystal distributed-feedback quantum cascade lasers emitting at 4.7 mu m. A rectangular photonic crystal lattice perpendicular to the cleaved facet was defined using holographic lithography. The anticrossing of the index- and Bragg-guided dispersions of rectangular lattice forms the band-edge mode with extended mode volume and reduced group velocity. Utilizing this coupling mechanism, single mode operation with a near-diffractive-limited divergence angle of 12 degrees is obtained for 33 mu m wide devices in a temperature range of 85-300 K. The reduced threshold current densities and improved heat dissipation management contribute to the realization of devices' room temperature operation.

Characterization and analysis of two-dimensional GaAs-based photonic crystal nanocavities at room temperature

This paper describes the design and fabrication process of a two-dimensional GaAs-based photonic crystal nanocavity and analyzes the optical characterization of cavity modes at room temperature. Single InAs/InGaAs quantum dots (QDs) layer was embedded in a GaAs waveguide layer grown on an Al0.7Ga0.3As layer and GaAs substrate. The patterning of the structure and the membrane release were achieved by using electron-beam lithography, reaction ion etching, inductively coupled plasma etching and selective wet etching. The micro-luminescence spectrum is recorded from the fabricated nanocavities, and it is found that some high-order cavity modes are clearly observed besides the lowest-order resonant mode is exhibited in spite of much high rate of nonradiative recombination. The variance of resonant modes is also discussed as a function of r/a ratio and will be used in techniques aimed to improve the probability of achieving spectral coupling of a single QD to a cavity mode.

Four-wave mixing self-stability based on photonic crystal fiber and its applications on erbium-doped fiber lasers

The analytic solutions of coupled-mode equations of four-wave mixings (FWMs) are achieved by means of the undepleted approximation and the perturbation method. The self-stability mechanism of the FWM processes is theoretically proved and is applicable to design a new kind of triple-wavelength erbium-doped fiber lasers. The proposed fiber lasers with excellent stability and uniformity are demonstrated by using a flat-near-zero-dispersion high-nonlinear photonic-crystal-fiber. The significant excellence is analyzed in theory and is proved in experiment. Our fiber lasers can stably lase three waves with the power ripple of less than 0.4 dB. (c) 2005 Elsevier B.V. All rights reserved.

Multi-wavelength erbium-doped fibre lasers on assistance of high-nonlinear photonic-crystal fibres

On the basis of self-stability effect of four-wave mixings (FWMs) in high-nonlinear photonic-crystal fibres, a novel multi-wavelength erbium-doped fibre (EDF) laser is proposed and demonstrated experimentally at room temperature. The proposed lasers have the capacity of switching and tuning with excellent uniformity and stability. By means of adjusting the attenuators, the triple-, four-, or five-wavelength EDF lasers can be lasing simultaneously. With the assistance of the FWM self-stability function, the multi-wavelength spectrum is excellently stabilized with uniformity less than 0.9 dB.

Polarization properties of elliptical core non-hexagonal symmetry polymer photonic crystal fibre

In this paper, polarization properties and propagation characteristics of polymer photonic crystal fibres with elliptical core and non-hexagonal symmetry structure are investigated by using the full vectorial plane wave method. The results how that the birefringence of the fibreis induced by asymmetries of both the cladding and the core. Moreover, by adjusting the non-symmetrical ratio factor of cladding eta from 0.4 to 1 in step 0.1, we find the optimized design parameters f the fibre with high birefringence and limited polarization mode dispersion, operating in a single mode regime at an appropriate wavelength range. The range of wavelength approaches the visible and near-infrared which is consistent with the communication windows of polymer optical fibres.

Determination of dispersion and nonlinear coefficients of photonic crystal fibers by degenerated FWM method

使用四波混频测试光子晶体光纤的色散和非线性参数

One-Dimensional InP-Based Photonic Crystal Quantum Cascade Laser Emitting at 5.36μm

An InP-based one-dimensional photonic crystal quantum cascade laser is realized. With photo lithography instead of electron beam lithography and using inductively coupled plasma etching, four-period air-semiconductor couples are defined as Bragg reflectors at one end of the resonator. The spectral measurement at 80K shows the quasi-continuous-wave operation with the wavelength of 5.36μm for a 22μm-wide and 2mm-long epilayer-up bonded device.

An All-E-Beam Lithography Process for the Patterning of 2D Photonic Crystal Waveguide Devices

We present an all-e-beam lithography (EBL) process for the patterning of photonic crystal waveguides.The whole device structures are exposed in two steps. Holes constituting the photonic crystal lattice and defects are first exposed with a small exposure step size (less than 10nm). With the introduction of the additional proximity effect to compensate the original proximity effect, the shape, size, and position of the holes can be well controlled.The second step is the exposure of the access waveguides at a larger step size (about 30nm) to improve the scan speed of the EBL. The influence of write-field stitching error can be alleviated by replacing the original waveguides with tapered waveguides at the joint of adjacent write-fields. It is found experimentally that a higher exposure efficiency is achieved with a larger step size;however,a larger step size requires a higher dose.

Design of Photonic Crystal Semiconductor Optical Amplifier With Polarization Independence

Slow-light effects in photonic crystal (PC) waveguides can enhance light-mater interaction near the photonic band edge, which can be used to design a short cavity length semiconductor optical amplifier (SOA). In this paper, a novel SOA based on slow-light effects in PC waveguides (PCSOA) is presented. To realize the amplification of the optical signal with polarization independence, a PCSOA is designed with a compensated structure. The cascaded structure leads to a balanced amplification to the TE and TM polarized light.

AlGaInP LED with surface structure of two-dimensional photonic crystal

Some progress in the research of GaN based LED with photonic crystal structure has been made recently. Based on the photonic crystal's photonic band gap effect and photon grating diffraction principle, the extraction efficiency of LED with photonic crystal can be improved. In this paper, the restriction on AlGaInP LED's extraction efficiency is analyzed, and the photonic crystal is introduced in to the AlGaInP LED to improve the extraction efficiency. The theoretical analyses and the experiment results show that the output luminous intensity of LED with photonic crystal is improved by 16%, which results from some effect of the GaN based LED with photonic crystal.

Fabrication and luminescence characterization of two-dimensional GaAs-based photonic crystal nanocavities

This paper describes the design and fabrication process of a two-dimensional GaAs-based photonic crystal nanocavity with InAs quantum dots (QDs) emitters and analyzes the optical characteristics of cavity modes at room temperature. The micro-luminescence spectrum recorded from the nanocavities exhibits a narrow optical transition at the lowest order resonance wavelength of about 1137 nm with about 1 nm emission linewidth. In addition, the spectra of photonic crystal nanocavities processed under different etching conditions show that the verticality of air hole sidewall is an important factor determing the luminescence characteristics of photonic crystal nanocaivties. Finally,,the variance of resonant modes is also discussed as a function of r/a ratio and will be used in techniques aimed at improving the probability of achieving spectral coupling of a single QD to a cavity mode.