High-speed photodetector characterization using tunable laser by optical heterodyne technique - art. no. 60200A

An ultra-wide-band frequency response measurement system for optoelectronic devices has been established using the optical heterodyne method utilizing a tunable laser and a wavelenath-fixed distributed feedback laser. By controlling the laser diode cavity length, the beat frequency is swept from DC to hundreds GHz. An outstanding advantage is that this measurement system does not need any high-speed light modulation source and additional calibration. In this measurement, two types of different O/E receivers have been tested. and 3 dB bandwidths measured by this system were 14.4GHz and 40GHz, respectively. The comparisons between experimental data and that from manufacturer show that this method is accurate and easy to carry out.

Harmonic mode-locked ytterbium-doped fibre ring laser

We demonstrate a harmonic mode-locked ytterbium-doped fibre ring laser, which consists of a polarization-sensitive isolator, two polarization controllers, two 976 nm laser diodes as the pump source and a two-segment ytterbium-doped fibre. Utilizing an additive pulse mode-locked technique based on nonlinear polarization evolution, the ytterbium-doped fibre laser can operate in mode-locked state by adjusting the position of polarization controllers. The cavity fundamental repetition rate is 23.78 MHz. We also observe the second- and third-harmonic mode locking in the normal dispersion region, and their repetition rates are 47.66 MHz and 71.56 MHz, respectively. Over-driving of the saturable absorber in the harmonic mode-locking pulse is analysed and discussed in detail.

Influence of annealed ohmic contact metals on electron mobility of strained AlGaN/GaN heterostructures

The influence of annealed ohmic contact metals on the electron mobility of a two dimensional electron gas (2DEG) is investigated on ungated AlGaN/GaN heterostructures and AlGaN/GaN heterostructure field effect transistors (AlGaN/GaN HFETs). Current-voltage (I-V) characteristics for ungated AlGaN/GaN heterostructures and capacitance-voltage (C-V) characteristics for AlGaN/GaN HFETs are obtained, and the electron mobility for the ungated AlGaN/GaN heterostructure is calculated. It is found that the electron mobility of the 2DEG for the ungated AlGaN/GaN heterostructure is decreased by more than 50% compared with the electron mobility of Hall measurements. We propose that defects are introduced into the AlGaN barrier layer and the strain of the AlGaN barrier layer is changed during the annealing process of the source and drain, causing the decrease in the electron mobility.

High Speed VCSEL-Based Parallel Optical Transmission Modules

Design and fabrication of a parallel optical transmitter are reported. The optimized 12 channel parallel optical transmitter,with each channel＇s data rate up to 3Gbit/s,is designed, assembled, and measured. A top-emitting 850nm vertical cavity surface emitting laser（VCSEL） array is adopted as the light source,and the VCSEL chip is directly wire bonded to a 12 channel driver IC. The outputs of the VCSEL array are directly butt coupled into a 12 channel fiber array. Small form factor pluggable （SFP） packaging technology is used in the module to support hot pluggable in application. The performance results of the module are demonstrated. At an operating current of 8mA, an eye diagram at 3Gbit/s is achieved with an optical output of more than 1mW.

A double wavelength DFB laser with an identical active area for CWDM

A novel distribute feedback (DFB) laser which gave two different wavelengths under two distinct work conditions was fabricated. The laser consists of two Bragg gratings with different periods corresponding to wavelength spacing of 20 nm in an identical active area. When driving current was injected into one of the different sections separately, two different wavelengths at 1542.4 and 1562.5 nm were realized. The side mode suppression ratio (SMSR) of 45 dB or more both for the two Bragg wavelengths were achieved. The fabricating process of the laser was just the same as that of traditional DFB laser diode. This device can be potentially used in coarse wavelength division multiplexer (CWDM) as a promising light source and the technology idea can be used to enlarge the transmission capacity in metro area network (MAN).

Real-time far distance micro-vibration measurement using an external cavity semiconductor laser interferometer with a feedback control system

An external cavity semiconductor laser interferometer used to measure far distance micro-vibration in real time is proposed. In the interferometer, a single longitudinal mode and excellent coherent characteristic grating external cavity semiconductor laser is constructed and acted as a light source and a phase compensator. Its coherent length exceeds 200 meters. The angle between normal and incidence beam of the far object is allowed to change in definite range during the measurement with this interferometer, and this makes the far distance interference measurement easier and more convenient. Also, it is not required to keep the amplitudes of the first and second harmonic components equal, and then the dynamic range is increased. A feedback control system is used to compensate the phase disturbance between the two interference beams introduced by environmental vibration.

Polymorphous silicon nanowires synthesized by plasma-enhanced chemical vapor deposition

Polymorphous Si nanowires (SiNWS) have been successfully synthesized on Si wafer by plasma enhanced chemical vapor deposition (PECVD) at 440degreesC,using silane as the Si source and Au as the catalyst. To grow the polymorphous SiNWS preannealing the Si substrate with Au film at 1100 degreesC is needed. The diameters of Si nanowires range from 15 to 100 urn. The structure morphology and chemical composition of the SiNWS have been characterized by high resolution x-ray diffraction, scanning electron microscopy, transmission electron microscopy, as well as energy dispersive x-ray spectroscopy. A few interesting nanowires with Au nanoclusters uniformly distributed in the body of the wire were also produced by this technique.

Nano-layer structure of silicon-on-insulator materials

Silicon-on-insulator (SOI) has been recognized as a promising semiconductor starting material for ICs where high speed and low power consumption are desirable, in addition to its unique applications in radiation-hardened circuits. In the present paper, three novel SOI nano-layer structures have been demonstrated. ULTRA-THIN SOI has been fabricated by separation by implantation of oxygen (SIMOX) technique at low oxygen ion energy of 45 keV and implantation dosage of 1.81017/cm2. The formed SOI layer is uniform with thickness of only 60 nm. This layer is of crystalline quality. and the interface between this layer and the buried oxide layer is very sharp, PATTERNED SOI nanostructure is illustrated by source and drain on insulator (DSOI) MOSFETs. The DSOI structure has been formed by selective oxygen ion implantation in SIMOX process. With the patterned SOI technology, the floating-body effect and self-heating effect, which occur in the conventional SOI devices, are significantly suppressed. In order to improve the total-dose irradiation hardness of SOI devices, SILICON ON INSULATING MULTILAYERS (SOIM) nano-structure is proposed. The buried insulating multilayers, which are composed of SiOx and SiNy layers, have been realized by implantation of nitride and oxygen ions into silicon in turn at different ion energies, followed by two steps of high temperature annealing process, respectively, Electric property investigation shows that the hardness to the total-dose irradiation of SOIM is remarkably superior to those of the conventional SIMOX SOI and the Bond-and-Etch-Back SOI.

Numerical simulation of thermal loading produced by shaped high power laser onto engine parts

Recently a new method for simulating the thermal loading on pistons of diesel engines was reported. The spatially shaped high power laser is employed as the heat source, and some preliminary experimental and numerical work was carried out. In this paper, a further effort was made to extend this simulation method to some other important engine parts such as cylinder heads. The incident Gaussian beam was transformed into concentric multi-circular patterns of specific intensity distributions, with the aid of diffractive optical elements (DOEs). By incorporating the appropriate repetitive laser pulses, the designed transient temperature fields and thermal loadings in the engine parts could be simulated. Thermal-structural numerical models for pistons and cylinder heads were built to predict the transient temperature and thermal stress. The models were also employed to find the optimal intensity distributions of the transformed laser beam that could produce the target transient temperature fields. Comparison of experimental and numerical results demonstrated that this systematic approach is effective in simulating the thermal loading on the engine parts. (C) 2009 Elsevier Ltd. All rights reserved.

薯蓣属植物甾体甙元和甾体皂甙对研究

本文介绍了薯蓣植物中所含甾体皂甙和甾体皂甙元的化学研究概括。阐述了该属植物皂甙和甙元的结构特点，简要介绍了提取分离及结构鉴定的新方法，并把从此属植物中分离得到的甾体皂甙和甾体皂甙元的来源，理化常数及13C-NMR的化学位移值以表格形式列出。本文的实验部分是从四川产黄山药根茎的乙醇提取物中分离得到六种甾体皂甙，其中三个为E—试剂正反应成分，用化学方法及IR、FDMS、13CNMR、1HNMR、DEPT等技术鉴定了他们的结构，都是薯蓣皂甙元的皂甙。The chemical study in steroid saponins and sapogenins from Dioscorea family is reviewed. Their stuctures are discussed, and the newer techniques used in their isolation and structural elucidation are briefly introduced. A compilation of the saponins and sapogenins from dioscorea family along with their available physical data, source and 13CNMR chemical shifts is included. The experimental paper is that six steroidal saponins were isolated from rhizomes of Dioscorea panthaica Prain et burkill from Sichuan province. Of these saponins the three are positive to Ehrlich reagent. With the aid of IR, FDMS, and NMR spectrometric analyses, their chemical structures have been elucidated as: 3-O-[α-L-rhamnopyranosyl(1→4)]-[β-D-glucopyranosyl]-diosgenin,3-O-[α-L-rhamnopyranosyl(1→2)]-[β-D-glucopyranosyl]-diosgenin; 3-O-[α-L-rhamnopyranosyl(1→2)]-[β-D-glucopyranosyl]-26-O-[β-D-glucopyranosyl]-diosgenin,3-O-[α-L-rhamnopy-ranosyl(1→2)]-[α-L-rhamnopyranosyl(1→4)]-β-D-glucopyranosyl-26-O-[β-D-glucopyranosyl]-diosgenin,3-O-[α-L-rhamnopyranosyl(1→2)]-[β-D-glucopyranosyl(1→3)]-β-D-glucopyranosyl-26-O-[β-D-glucopyranosyl]-diosgenin

川西北高寒草甸土壤呼吸研究：季节动态和放牧效应

除植被冠层的光合作用之外，土壤的呼吸作用是陆地生态系统碳收支中最大的通量。土壤呼吸即使发生较小的变化也能显著地减缓或加剧大气中CO2浓度的增加，从而明显影响到全球气候变化。土壤呼吸速率变化与否以及变化的方向可以反映生态系统对环境变化的敏感程度和响应模式。尽管如此，土壤呼吸仍是一个为人们了解不多的生态系统过程。 草地生态系统是陆地生态系统的一个重要组成部分。针对草地土壤呼吸进行野外实验研究和相应方法论的探讨将对区域乃至全球碳源汇性质的准确估算具有重要的科学意义。然而，近几年来关于草地土壤呼吸的主要研究工作都集中在温带草原和部分热带草原，而针对高寒草甸生态系统土壤呼吸的研究报道还很少。 2008年4月至2009年4月期间，我分别在2008年6、8、10、12月和2009年2月和4月分6次对川西北的典型高寒草甸群落的土壤呼吸进行观测，分析了不同类型高寒草甸群落土壤呼吸的季节变化特征以及环境因子和放牧模式对其影响。主要研究结果如下： 1）该地区高寒草甸生态系统在生长季（6月～8月）土壤呼吸速率较大（6.07～9.30μmolCO2¡m-2¡s-1 ） ， 在非生长季（ 12 月～ 2 月） 较小（ 0.16 ～0.49μmolCO2¡m-2¡s-1 ） 。土壤CO2 年累积最大释放量为3963 ～ 5730gCO2¡m-2¡yr-1，其中，生长季土壤CO2的释放量占年总释放量的85%～90%。非生长季占10%～15%。非生长季所占比例略小于冬季积雪覆盖地区的冬季土壤呼吸占年土壤呼吸量的比例（14%～30%）。温度，尤其地温，是影响该地区高寒草甸生态系统土壤呼吸速率的最主要环境因子。土壤呼吸速率与地上生物量和土壤水分之间没有显著相关性，但是土壤含水量过大会导致土壤呼吸速率下降。 2）在观测期内，草丘区的土壤呼吸显著高于对照区的土壤呼吸，其最大土壤呼吸速率为16.77μmolCO2¡m-2¡s-1，土壤CO2 年累积最大释放量为8145gCO2¡m-2¡yr-1，是对照区的近2 倍。由于草丘在高寒草甸中占有较大的面积比例（近30%），因此，它将对高寒草甸生态系统的碳循环起着重要的作用。 3）放牧模式不仅可以影响高寒草甸群落的土壤CO2 排放，而且还可以改变土壤呼吸的温度敏感性（Q10）。本研究表明，在生长季有长期放牧活动干扰时将会增加土壤向大气中释放二氧化碳的速度，促使土壤碳库中碳的流失。禁牧样地的土壤呼吸速率在刚禁牧时先迅速增大，随着禁牧时间的延长土壤呼吸速率将会下降。此外，与其它放牧模式相比，冬季放牧将高寒草甸群落土壤呼吸速率在生长季达到最大值的时间明显向后推迟。不同放牧模式下高寒草甸群落土壤呼吸的Q10 值大小顺序为：禁牧一年群落>冬季放牧群落>禁牧三年群落>夏季放牧群落>自由放牧群落。 4）基于呼吸室技术的观测方法中，测量前的剪草处理可以明显改变该地区高寒草甸群落的土壤温度和土壤呼吸速率。在生长季，剪草处理将使土壤呼吸速率的瞬时响应增加90%左右。由于剪草处理明显增加了剪草样方白天的土壤温度，而土壤温度与土壤呼吸之间存在着极显著的指数相关关系，因而剪草处理导致土壤呼吸速率迅速增加。因此，在高寒地区基于呼吸室技术观测的土壤呼吸应当进行校正。 综上所述，川西北高寒草甸生态系统土壤呼吸速率在生长季较高，而在非生长季较低。土壤温度是影响该地区土壤呼吸的最主要环境因子。在实验观测期，草丘区土壤呼吸速率显著高于对照区的，是对照区土壤呼吸速率的近2倍。由于测量前的剪草处理可以明显改变待测点的土壤呼吸速率，因此，应对在高寒地区基于呼吸室技术观测的土壤呼吸进行校正。 Soil respiration is the second largest component (less than plant phtotosynthesis) of carbon dioxide flux between terrestrial ecosystems and the atmosphere. A minor change in soil respiration rate can significantly slow down or accelerate the increase of atmospheric CO2 concentration that is closely related to global climatic change. In turn, the change in the flux direction and rate of soil respiration may indicate the elasticity and stability of ecosystems to global changes and human disturbance. However, soil respiration is still an ecosystem process that has been poorly understood. Grassland ecosystem is an important component of the terrestrial ecosystem. Accurately estimating the CO2 flux from soil to atmosphere in situ is the key to evaluating the carbon resource and sink regionally or globally. Despite of extensive studies on the temperate and tropic grasslands, the soil respiration of alpine meadows has not substantially been measured. In the current study, soil respiration was measured for an annual cycle from April, 2008 to April, 2009 for the alpine meadow in northwestern Sichuan Province of China to determine the seasonal variation of soil respiration for the typical plant communities. The results are shown as follows: 1) Large seasonal variation of soil respiration was observed in the alpine meadow. The rate of soil respiration was the greatest (6.07～9.30μmolCO2¡m-2¡s-1) in June and the smallest (0.16 ～ 0.49μmolCO2¡m-2¡s-1) occurred from December to February in the non-growing season. The total emission of soil CO2 was estimated as 3963～5730 gCO2¡m-2¡yr-1, 85%~90% of which was released during the growing season, and 10%~15% during the non-growing season which was slightly less than the ratio of winter and annual CO2 flux from soil. Temperature, particularly the soil temperature, was the major environmental factor regulating the soil respiration. Significant and positive relationships were not found between soil respiration and soil moisture and between soil respiration and plant above-ground biomass, but excessive soil water content would decrease in the rate of soil respiration. 2) The rate of soil respiration in grass hummock communities was up to 16.77μmolCO2¡m-2¡s-1, which was about twice as great as in the controls (communities located in low and even sites). Considering the large proportion (about 30% on average) of hummock area in the meadow, it can be concluded that the hummocks played an important role in the carbon cycling of the study ecosystem. 3) Grazing patterns affected the flux of CO2 emission and the temperature sensitivity of soil respiration (Q10) in the alpine meadow. Grazing during growing season increased the rate of soil respiration. The rate of soil respiration increased significantly immediately after the alpine meadow being fenced, but thereafter decreased. In addition, grazing in winter delayed the peak respiration rate relative to the non-grazing mode. The Q10 value was the largest in the non-grazed area for one year, and next came the area with grazing in winter, followed by the non-grazed area for three years, the area with grazing in summer, and the non-limited grazed area. 4) In the chamber-based techniques, clipping manipulation before each measurement increased the transient rate of soil respiration by about 90% in the summer of the alpine meadow. As increase in soil temperature at daytime in the clipped plots by clipping and the exponential relationship between soil respiration and temperature, clipping manipulation led to increase in the rate of soil respiration. This suggested that a correction should be done for the techniques if employed in alpine and cold regions. In summary, the rate of soil respiration in the alpine meadow was the greatest in June and the smallest occurred from ecember to February in the non-growing season. Soil temperature was the major environmental factor regulating the soil respiration. The rate of soil respiration in grass hummock communities was up to 16.77μmolCO2¡m-2¡s-1, which was about twice as great as in the controls. A correction should be done for the techniques if employed in alpine and cold regions, because of the effect of clipping manipulation on soil temperature and respiration.

生物催化的Baeyer-Villiger氧化反应研究

Baeyer-Villiger氧化反应是一种很重要的化学反应，产生的许多中间体或产物可以被用来生产多种化学产品和药物。此反应具有多功能性，可以氧化多种羰基化合物，但是化学方法中的必需反应物——氧化剂在生产、储存、运输、反应的过程中都存在很多的不安全因素，反应的立体选择性也不强，而生物转化则具有底物选择性、立构选择性、化学选择性、对映选择性等一般化学反应中不具备的优点，在精细化工中占有很大的优势。在工业生物催化中有很好的应用前景。 为了研究生物催化的Baeyer-Villiger反应，我们从本实验室保藏菌种中分离筛选出一株能够以环己酮作为唯一碳源的菌株，进行初步研究并对其产物进行GC/MS定性，探讨了pH，装液量，底物浓度，培养时间，温度以及转速等条件对细菌生长的影响，并进一步研究了细菌的底物广谱性。 此菌株经鉴定属于邻单胞菌属Plesiomonas sp.)， 根据正交试验，确定了菌的最佳生长条件：底物浓度为1mL/L，底物浓度过高对菌株生长有抑制作用，转速为150 rpm ，温度为30℃ ，pH为7.0； 此菌株转化环己酮的产物通过GC/MS检测含有内酯，表明此菌株能够催化Baeyer-Villiger氧化反应；此菌株还能够以与环己酮有相似结构的环己烷，环戊酮等作为唯一碳源生长，说明此菌株底物利用范围比较广，用途比较广泛。 Baeyer-Villiger oxidation is an important chemical conversion, its products and intermediates can be used to produce a lot of medicine and fine chemicals. Its success is largely due to its versatility: a variety of carbonyl compounds can be oxidized, a large number of functional groups are tolerated, the regiochemistry is highly predictable and so on, but the oxidants that the traditional chemistry way needs have a number of problem in their production, storage, transportation and reaction, Chemistry way has not a high stereochemistry yet. However, biotransformations have many attractive characters, such as substrate-, stereo-, chemo- and enantioselectivity, so it has a great advantage in the fine chemical industry and has a bright prospect in the industrial biological catalysis. In order to study Baeyer-Villiger oxidation, we isolated a strain which can utilize cyclohexanone as sole carbon source and had a primary research on it. Its product was identified by GC/MS. Effects of pH, volume, concentration of cyclohexanone, cultivating time, temperature and rotate speed on the growth of bacteria were discussed, and the other organic substrates were also studied. The strain was identified as Plesiomonas sp.. The result of orthogonal test made it sure that the best growth condition of the strain is: rotate speed 150 rpm, temperature 30℃, pH7.0, concentration of cyclohexanone1ml/L. There is caprolactone in the product of the fermentation with cyclohexanone as substrate by GC/MS,which indicated that the strain can catalyse Baeyer-Villiger oxidation.In addition,the strain can utilize other organic substrates having the similar structure with cyclohexanone such as cyclohexane, cyclopentanone, Swertiamarin as sole carbon source.So the strain can be applied extentively.

耐酸产甲烷菌的分离及其复合菌剂的研究

本文从成都龙泉垃圾填埋场和宜宾造纸厂分离到耐酸性能优良的高温产甲烷菌RY3和中温产甲烷菌SH4，并将其与实验室现有的利用不同底物的产甲烷菌配伍组合成了复合菌剂。采用活性污泥作为固体附着物，研制出了固体产甲烷菌复合菌剂。 菌株RY3的pH耐受范围为5.5～10.5，最适生长pH 6.0～8.0。菌株RY3为革兰氏阳性，长杆状，多数单生，不运动；菌落浅黄色，形状近圆形；利用H2+CO2或甲酸盐作为唯一碳源生长，不利用乙酸盐，对氯霉素非常敏感。该菌最适生长温度为55℃～65℃，最适NaCl浓度为0～2%。根据形态和生理生化特性及16S rDNA序列分析将其初步定为热自养甲烷热杆菌（Methanothermobacter thermautotrophicus）。添加RY3菌液与仅添加厌氧污泥作为接种物相比一周内可使达到最大产甲烷速率所需时间缩短三分之二，甲烷总产量提高约1.8倍。菌株SH4的生长pH范围5.5～9.5，其对酸碱具有良好的适应性，培养3天后，在初始pH值为6.0～8.0的培养基中甲烷产量相差不大，且基本达到最大产量。SH4革兰氏染色阳性，短杆状，多数单生，不运动；菌落近圆形，微黄；利用H2+CO2或甲酸盐作为唯一碳源生长，不利用乙酸盐，对氯霉素非常敏感。SH4最适生长pH 为7.0，最适生长温度为35℃，最适NaCl浓度为0～1.5%。实验表明，添加SH4菌液与仅添加厌氧污泥作为接种物相比可使产甲烷启动时间缩短三分之一，甲烷总产量亦有大幅提高。从形态和生理生化特征以及16S rDNA序列分析表明SH4为嗜树木甲烷短杆菌（Methanobrevibacter arboriphilus）。 以活性污泥为附着物，与培养基和菌种经搅拌后厌氧发酵可得产甲烷菌固体复合菌剂。固体复合菌剂的pH耐受范围为5.5～9.5，温度耐受范围为15℃～65℃，表明其对环境的适应性较强。以猪粪为底物进行厌氧发酵，接种复合菌剂进行试验，以接种实验室长期富集的产甲烷厌氧污泥作为对照，在20℃时，发酵甲烷浓度与对照基本一致，但每日产气量优于对照，第15天时接种复合菌剂的发酵瓶每日产气量是对照的1.59倍；50℃时达到最大甲烷含量所需时间比对照缩短三分之二，三周内总产气量约为对照的2.7倍，甲烷总产量约为2.8倍。以不加接种物为对照，接种复合菌剂20℃时发酵甲烷含量达到50%约需2周，对照2周内甲烷含量最高仅为4.3%；50℃时接种复合菌剂发酵仅需约1周甲烷含量便可达50%，对照则至少需要2周。 In this paper, high-temperature Methanogen RY3 and middle-temperature SH4 were isolated from Chengdu Longquan refuse landfill and Yibin paper mill. They could be used to make compound inoculum that producing methane with the existing Methanogens utilized different substrate. With using anaerobic activated sludge be solid fixture, the process had been designed to produce solid compound inoculum. Strain RY3 possessed excellent capacity of acid and alkali-tolerant. The pH-tolerant scale of RY3 was 5.5～10.5 and its optimum pH value for growth was 6.0～8.0. RY3 was G+, long-rod shape, monothetic and nonmotile, the colony was pale yellow with suborbicular-shape. Formate or H2+CO2 but not acetate was utilized by RY3 as sole C-source, and it was very sensitive to chloramphenicol. Besides, strain RY3 grew fastest at 55℃～65 and 0℃～2% NaCl. Characteristics of modality and physiology with sequence analysis of the 16s rDNA gene of strain RY3 preliminarily showed that it was Methanothermobacter thermautotrophicus. The experiments indicated that the time which began to produce methane with the highest velocity could be shortened two third by adding RY3 in one week, and the total methane production also was 1.8 times than before. Strain SH4 possessed wide scale of growing pH（5.5～9.5）and excellent ability of acclimatizing itself to acid-alkali. The methane production had no apparent difference among those cultivated in different initial pH（6.0～8.0）after three days and equaled to the maximum production basically. Cells of SH4 were G+, short-rod sharp, monothetic and nonmotile. The colony was pale yellow with suborbicular-shape. Formate or H2+CO2 but not acetate was utilized by SH4 as sole C-source, and it was very sensitive to chloramphenicol. Besides, it grew fastest at pH 7.0，55 ℃～65 and 0℃～2% NaCl concentration. The experiment indicated the time that began to produce methane could be shortening one third by adding SH4. And the total methane production also rose apparently. Characteristic of modality and physiology with sequence analysis of the 16S rDNA gene of strain SH4 demonstrated it was Methanobrevibacter arboriphilus. The activated sludge was utilized as fixture, mixed with culture medium and inocolum, that the solid compound inoculum could be produced by anaerobic fermentation. The compound inoculum could grow between pH 5.5～9.5, 15℃～65. It demonstrated the compound inoculum ha℃ve great ability of adapting to circumstance. In the experiment that making pig manure be substrate and taking the anaerobic sludge producing methane that cultured in long term in laboratory to be comparison, the concentration of methane in fermentation added compound inoculum almost equal to the comparison at 20℃, but the volume of gas production could be a little higher. The gas production everyday inoculated compound inoculum was 1.59 times to comparison. The time that the concentration of methane to maximum could be shortening by two third by adding compound inoculum, and the total gas production was 2.7 times to comprison while the total methane production was 2.8 times. If take the no inoculum be the comprasion, anaerobic fermentation added compound inoculum made the concentration of methane to 50% in 2 weeks but the comparison only to 4.3% at 20℃. The time that the concentration of methane to 50% by adding compound inoculum only need 1 week, but the comparison need 2 weeks at 50℃.

一株丝状真菌对半纤维素利用的初步研究

本文筛选出一株能利用木糖产乙醇的丝状真菌Z7，对其利用木糖和半纤维素水解产物产乙醇的发酵条件进行了研究，并对Z7 利用玉米芯产木聚糖酶的条件进行了优化。全文分为三部分： 第一部分：目标微生物筛选、纯化及系统发育分析。以木糖为唯一碳源，采用梯度稀释和平板化线法从高温、中温酒曲中分离到16 株能利用木糖良好生长的丝状真菌；通过发酵试验复筛，获得一株能产乙醇的丝状真菌Z7；综合形态学和ITS 序列分析，初步鉴定为Aspergillus flavus。 第二部分：Z7 的乙醇发酵条件研究。以木糖为碳源，通过单因素试验确定最佳氮源和发酵温度；通过正交试验及SPSS 软件分析得到了不同N、P、K 成分对乙醇、残糖和菌体干重的影响。获得最佳的发酵条件为：（g/L）木糖50，尿素1, NH4NO3 1, K2HPO4 2 , KCl 0.5 , MgSO4.7H2O 0.5 , NaNO3 1 , pH 自然，培养温度33 ℃。以玉米芯半纤维素稀酸水解液为底物进行乙醇发酵，根据稀酸水解的单糖释放量和乙醇产量，确定115 ℃，1 h 为最佳玉米芯预处理条件；结合最佳发酵条件，添加1 g/L 的吐温20 能获得最大的乙醇浓度8.31 g/L。因此，Aspergillus flavus Z7 能利用半纤维素水解产物产乙醇，其中木糖的利用率80%以上。 第三部分：Z7 利用玉米芯产木聚糖酶条件优化。Aspergillus flavus Z7 在具有产乙醇能力的同时还具有产木聚糖酶的能力。本文通过单因素和正交试验得到最佳产酶培养基组分为：(g/L)玉米芯20，尿素2, 酵母膏2.5, K2HPO4 5，NaNO31, MgSO4.7H2O 1。单因素试验表明，用纱布代替塑料布密封摇瓶封口能显著提高产酶量；Z7 在碱性条件下具有更强的产酶性能。在最优条件下发酵，能产生最大木聚糖酶活122.23IU/mL。通过薄层分析，验证了Z7 产生的木聚糖酶具有水解木聚糖生成木糖及木寡糖的能力。 A strain of filamentous fungus which can produce ethanol by using the xylose was isolated in this research. The ethanol fermention conditions from xylose and dilute-acid hydrolyzate of the corn core were studied. The conditions of xylanase production by Z7 were also optimized. The paper involved three parts. Part1: Isolation, purification and phylogenetic analysis of the microbe. By using xylose as the single carbon source and the pla te streaking method, several filamentous fungi were isolated from the wine starter; through the fermentation test, a filamentous fungus Z7 which can produce ethanol was further recognized; furthermore, according to the morphologic observation and ITS seque nces analysis, Z7 was identified as Aspergillus flavus at the first step. Part2: Research on the condition of ethanol fermentation by Z7. By single factor experiment, the optional nitrogen resource and temperature of the fermentation were fixed; meanwhile, through the orthogonal array tests and the analysis of statistic software SPSS, the optional component of the culture medium and the fermentation condition were organized as follows: (g/L) xylose 50, urea 1, NH4NO3 1, K2HPO4 2, KCl 0.5 , MgSO4.7H2O 0.5, NaNO31, pH nature, temperature 33℃. Based on these optimal parameters, the fermentation of dilute-acid hydrolyzate of the corn core was carried on by Z7. According to the quantities of released sugar monomers and content of the ethanol, 115℃ in 1h is the best pretreatment condition; the maximal ethanol content can be obtained when 1g/L Tween 20 was added to. Therefore, the filamentous fungus Aspergillus flavus can use the hydrolysate of hemicellulose to produce ethanol, and the rate of xylose utilization was over 80%. Part3: Optimization of Z7’s xylanase producing condition from corn core. Aspergillus flavus Z7, which can utilize xylose or the hydrolysate of hemicellulose to produce ethanol, also had the ability of xylanase production. The optional component of the culture medium were fixed by the single factor experiment and the orthogonal array tests, and they were organized as follows: (g/L) corn core 20, Urea 2, Yeast extract 2.5, K2HPO4 5, NaNO31, MgSO4.7H2O 1; it was testified by the single factor experiment that sealing the shaking flasks with pledget other than plastic paper can obviously increase the xylanase activity; moreover, Z7 showed better xylanase production ability when in the alkali environment. Under the optional fermentation condition, the maximal xylanase activity 122.23IU/mL was proved. Through the analysis of thin- layer chromatography (TLC), the ability of xylanase from Z7, which can hydrolyze xylan to xylose monomer and oligomer, was vividly displayed.

Study of the interaction of highly charged ions with SiO2 surface

Highly charged ions (HCIs) AO(q+)/Pbq+ are extracted from ECR source and impacted on solid surface Of SiO2 Sputtering yield as a function of incident angle is measured by multi-channel plate (MCP). The results have been fitted by a new formula. We proposed the cooperation model to explain the formula. The results demonstrate that the potential assisted kinetic sputtering yield increases with the charge state and potential sputtering (PS) could be induced by impact of HCIs. At larger incident angles, the sputtering yield is dominated by elastic collision between HCIs and material atoms. It is found that, smaller the incident angle, larger the contribution from the potential sputtering. (C) 2009 Elsevier B.V. All rights reserved.