A standard CMOS compatible monolithic photo-detector and trans-impedance amplifier

A 1GHz monolithic photo-detector (PD) and trans-impedance amplifier (TIA) is designed with the standard 0.35 mu m CMOS technique. The design of the photo-detector is analyzed and the CMOS trans-impedance amplifier is also analyzed in the paper. The integrating method is described too. The die photograph is also showed in the paper.

A CMOS front-end circuit for SONET OC-96 receiver

An optical receiver front-end for SONET OC-96 receivers was analyzed and designed in 0.18 mu m CMOS process. It consists of a transimpedance amplifier (TIA) and a limiting amplifier (LA). The TIA takes a fully differential configuration, and regulated cascode (RGC) input stage is implemented. The LA was realized by five cascaded identical gain stages with active inductor load. The TIA achieved 4.2GHz bandwidth for 0.5pF photodiode (PD) capacitance and 1.2k 0 transimpedance gain. The LA achieved 5.4GHz bandwidth and 29dB voltage gain. The optical sensitivity is -19dBm at 5-Gb/s for a bit-error rate of 10(-12), and it dissipates 45.5mW for I.8V supply.

A silicon light emitting devices in standard CMOS technology

A silicon light emitting device is designed and simulated. It is fabricated in 0.6 mum standard CMOS technology. The device can give more than 1 muW optical power of visible light under reverse breakdown. The device can be turned on at a bias of 0.88 V and work in a large range of voltage: 1.0-6.0 V The external electrical-optical conversion efficiency is more than 10(-6). The optical spectrum of the device is between 540-650 nm, which have a clear peak near 580 nm. The emission mechanism can be explained by a hot carrier direct recombination model.

Behavior model of a CMOS process compatible photo-diode

A behavior model of a photo-diode is presented. The model describes the relationship between photocurrent and incident optical power, and it also illustrates the impact of the reverse bias to the variation of the junction capacitance. With this model, the photo-diode and a CMOS receiver circuit were simulated and designed simultaneously under a universal circuit simulation environment.

Circuit design and simulation of a CMOS-based preamplifier for brain neural signals

A novel CMOS-based preamplifier for amplifying brain neural signal obtained by scalp electrodes in brain-computer interface (BCI) is presented in this paper. By means of constructing effective equivalent input circuit structure of the preamplifier, two capacitors of 5 pF are included to realize the DC suppression compared to conventional preamplifiers. Then this preamplifier is designed and simulated using the standard 0.6 mu m MOS process technology model parameters with a supply voltage of 5 volts. With differential input structures adopted, simulation results of the preamplifier show that the input impedance amounts to more than 2 Gohm with brain neural signal frequency of 0.5 Hz-100 Hz. The equivalent input noise voltage is 18 nV/Hz(1/2). The common mode rejection ratio (CMRR) of 112 dB and the open-loop differential gain of 90 dB are achieved.

An Ultra Low Power Non-volatile Memory in Standard CMOS Process for Passive RFID Tags

An ultra low power non-volatile memory is designed in a standard CMOS process for passive RFID tags. The memory can operate in a new low power operating scheme under a wide supply voltage and clock frequency range. In the charge pump circuit the threshold voltage effect of the switch transistor is almost eliminated and the pumping efficiency of the circuit is improved. An ultra low power 192-bit memory with a register array is implemented in a 0.18 mu M standard CMOS process. The measured results indicate that, for the supply voltage of 1.2 volts and the clock frequency of 780KHz, the current consumption of the memory is 1.8 mu A (3.6 mu A) at the read (write) rate of 1.3Mb/s (0.8Kb/s).

A Novel CMOS Color Pixel for Vision Chips

This paper presents a novel CMOS color pixel with a 2D metal-grating structure for real-time vision chips. It consists of an N-well/P-substrate diode without salicide and 2D metal-grating layers on the diode. The periods of the 2D metal structure are controlled to realize color filtering. We implemented sixteen kinds of the pixels with the different metal-grating structures in a standard 0.18 mu m CMOS process. The measured results demonstrate that the N-well/P-substrate diode without salicide and with the 2D metal-grating structures can serve as the high speed RGB color active pixel sensor for real-time vision chips well.