Optimization of InGaAs quantum dots for optoelectronic applications

Quantum dot infrared photodetectors (QDIP) are in the center of research interest nowadays. However the real QDIP is inferior to those predicted in theory, in which the dot density is much higher than those reported. Through optimizing the growth conditions, we realized the control of high-density quantum dot growth. This will be very useful for future QDIP development.

Strained MQW electro-absorption modulators with high extinction ratio and low capacitance

We fabricate an electro-absorption modulator for optical network system using a new strategy, the improved modulation properties of the strained InGaAs/InAlAs MQW show it's polarization independent, high extinction ratio (> 40dB) and low capacitance (C <0.6pF) which can achieve an ultra-high frequency(> 10GHz). The device is be used in 10Gbps optical time division multiplex (OTDM) system as a signal generator.

Residual donors in undoped LEC InP

Undoped liquid encapsulated Czochralski (LEC) InP samples have been studied by Hall effect, glow discharge mass spectroscopy (GDMS) and infrared absorption spectroscopy. A systematic discrepancy has been found between the Han electron concentration and net donor concentration measured by GDMS. The electron concentration is always higher than the net shallow donor concentration by about (3-6)x10(15)cm(-3). A hydrogen indium vacancy complex donor defect VInH4 was detected regularly by infrared absorption spectroscopy in all undoped LEC InP samples. The fact can be explained by taking into account the existence of the donor defect in as-grown undoped LEC-InP.

Fabrication of silicon-on-reflector for Si-based resonant-cavity-enhanced photodetectors

A novel silicon-on-reflector substrate for Si-based resonant-cavity-enhanced photodetectors has been fabricated by using Si-based sol-gel and smart-cut techniques. The Si/SiO2 Bragg reflector is controlled in situ by electron beam evaporation and the thickness can be adjusted to get high reflectivity. The reflectance spectra of the silicon-on-reflector substrate with five pairs of Si/SiO2 reflector have been measured and simulated by transfer matrix model. The reflectivity at operating wavelength is close to 100%. Based on the silicon-on-reflector substrate, SiGe/Si multiple quantum wells resonant-cavity-enhanced photodetectors for 1.3 mu m wavelength have been designed and simulated. Ten-fold enhancement of the quantum efficiency of resonant-cavity-enhanced photodetectors compared with conventional photodetectors is predicted.

High power continuous-wave operation of self-organized In(Ga)As/GaAs quantum dot lasers

Quantum dot (QD) lasers are expected to have superior properties over conventional quantum well lasers due to a delta-function like density of states resulting from three dimensional quantum confinements. QD lasers can only be realized till significant improvements in uniformity of QDs with free of defects and increasing QD density as well in recent years. In this paper, we first briefly give a review on the techniques for preparing QDs, and emphasis on strain induced self-organized quantum dot growth. Secondly, self-organized In(Ga)As/GaAs, InAlAs/GaAlAs and InAs/InAlAs Qds grown on both GaAs and InP substrates with different orientations by using MBE and the Stranski-Krastanow (SK) growth mode at our labs are presented. Under optimizing the growth conditions such as growth temperature, V/III ratio, the amount of InAs, InxGa1-xAs, InxAl1-xAs coverage, the composition x etc., controlling the thickness of the strained layers, for example, just slightly larger than the critical thickness and choosing the substrate orientation or patterned substrates as well, the sheet density of ODs can reach as high as 10(11) cm(-2), and the dot size distribution is controlled to be less than 10% (see Fig. 1). Those are very important to obtain the lower threshold current density (J(th)) of the QD Laser. How to improve the dot lateral ordering and the dot vertical alignment for realizing lasing from the ground states of the QDs and further reducing the Jth Of the QD lasers are also described in detail. Thirdly based on the optimization of the band engineering design for QD laser and the structure geometry and growth conditions of QDs, a 1W continuous-wave (cw) laser operation of a single composite sheet or vertically coupled In(Ga)As quantum dots in a GaAs matrix (see Fig. 2) and a larger than 10W semiconductor laser module consisted nineteen QD laser diodes are demonstrated. The lifetime of the QD laser with an emitting wavelength around 960nm and 0.613W cw operation at room temperature is over than 3000 hrs, at this point the output power was only reduced to 0.83db. This is the best result as we know at moment. Finally the future trends and perspectives of the QD laser are also discussed.

Wavelength tunable electroabsorption modulated DFB baser with thin film heater

　

The development of long - Term ambulatory pH monitoring system and its clinical application

This paper introduced a long-term ambulatory intragastric pH monitoring system, which is designed for prolonged ambulatory studies of Gastroesophageal Reflux Diseases. The whole system is composed of the gastric catheter with two pH sensors, a small data logger (Microdatalog), and a notebook PC. In this paper, the design of monitoring system hardware and software are described in detail. Clinical applications reveal good results.

Measurement of respiratory acoustic impedance in children by a modified forced oscillation method

An introduction to a modified forced oscillation method, square-wave excitation technique, including fundamentals and methods, as used in respiratory function examination. On the basis of experimental results and theoretical predictions, we suggest that Respiratory Acoustic Impedance (RAI) measurement by spectral analysis can significantly improve estimation of contribution to RAI from different part of respiratory tract. The outcome is of considerable interest in the study of lung disease, such as COPD and asthma in young children.

Artificial neural networks expecting more advanced microelectronics technology

　

JFET SOS devices: Processing and gamma radiation effects

A process for fabricating n channel JFET/SOS (junction field-effect transistors on silicon-on-sapphire) has been researched. The gate p(+)n junction was obtained by diffusion, and the conductive channel was gotten by a double ion implantation. Both enhancement and depletion mode transistors were fabricated in different processing conditions. From the results of the Co-50 gamma ray irradiation experimental we found that the devices had a good total dose radiation-hardness. When the tot;ll dose was 5Mrad(Si), their threshold voltages shift was less than 0.1V. The variation of transconductance and the channel leakage current were also little.

Improvement of CMOS SOS devices characteristics by a modified solid phase epitaxy

CMOS/SOS devices have lower carriers mobility and higher channel leakage current than bulk silicon CMOS devices. These mainly results from the defects of heteroepitaxial silicon film, especially from the defects near Si-Sapphire interface. This paper describes the experiment results of CMOS/SOS devices characteristics improved by a better epitaxial silicon quality which is obtained by a modified solid phase epitaxy.

Dependence of ultra-thin gate oxide reliability on surface cleaning approach

In this paper, we investigate the effect of silicon surface cleaning prior to oxidation on the reliability of ultra-thin oxides. It is demonstrated that chemical preoxide grown in H2SO4/H2O2 (SPM) solution prior to oxidation provides better oxide integrity than both HF-based solution dipping and preoxide grown in RCA SC1 or SC2 solutions. It is also found that the oxides with SPM preoxide exhibit better hot-carrier immunity than the RCA cleaned oxides.

A new half-flash architecture for high speed video ADC

In this paper a new half-flash architecture for high speed video ADC is presented. Based on a high speed single-way analog switch circuit, this architecture effectively reduces the number of elements. At the same lime no sacrifice of speed is needed compared with the normal half-flash structure.

The design of cascaded resistors in a new analog switch two-step ADC architecture

In this paper we introduce a new Half-flash analog switch ADC architecture. And we discuss two methods to design the values of the cascaded resistors which generate the reference voltages. Derailed analysis about the effect of analog switches and comparators on reference voltages, and the methods to set the resistor values and correspond;ng voltage errors are given.

An analysis of the performance of a new high-speed single-way analog switch

This paper introduces a new highspeed single-way analog switch which has both highspeed high-resolution mono-direction analog transmission gate function and high-speed digital logic gate function with normal bipolar technology. The analysis of static and transient switching performances as an analog transmission gate is emphasized in the paper. In order to reduce the plug-in effect on high-speed high-resolution systems, an optimum design scheme is also given. This scheme is to achieve accelerated dynamic response with very low bias power dissipation. The analysis of PSPICE simulation as well as the circuit test results confirms the feasibility of the scheme. Now, the circuit has been applied effectively to the designs of novel highspeed A/D and D/A converters.