Evaluating 0.53 eVGaInAsSbthermophotovoltaic diode based on an analytical absorption model

Radiant heat conversion performance dominated by the active layer of Ga0.84In0.16As0.14Sb0.86 diode has been systematically investigated based on an analytic absorption spectrum, which is suggested here by numerically fitting the limited experimental data. For the concerned diode configuration, our calculation demonstrates that the optimal base doping is 3-4 x 10(17) cm(-3), which is less sensitive to the variation of the external radiation spectrum. Given the scarcity of the alloy elements, an economical device configuration of the 0.2-0.6 mu m emitter and the 4-6 mu m base would be particularly acceptable because the corresponding conversion efficiency cannot exhibit discouraging degradation in comparison to the one for the optimal structure, the thickness of which may be up to 10 mu m. More importantly, the method we suggested here to calculate alloy absorption can be easily transferred to other composition, thus bringing great convenience for design or optimization of the optoelectronic device formed by these alloys.

PRESSURE-DEPENDENCE OF PHOTOLUMINESCENCE IN IN(X)GA(1-X)AS/AL(Y)GA(1-Y)AS STRAINED QUANTUM-WELLS WITH DIFFERENT WIDTH

A systematic investigation on the photoluminescence (PL) properties of InxGa1-xAs/AlyGa1-xAs (x = 0.15, y = 0, 0.33) strained quantum wells (SQWs) with well widths from 1.7 to 11.0 nm has been performed at 77 K under high pressure up to 40 kbar. The experimental results show that the pressure coefficients of the exciton peaks corresponding to transitions from the first conduction subband to the heavy-hole subband increase from 10.05 meV/kbar of 11.0 nm well to 10.62 meV/kbar of 1.8 nm well for In0.15Ga0.85As/GaAs SQWs. However, the corresponding pressure coefficients slightly decrease from 9.93 meV/kbar of 9.0 nm well to 9.73 meV/kbar of 1.7 nm well for In0.15Ga0.85As/Al0.33Ga0.67As SQWs. Calculations based on the Kronig-Penney model reveal that the increased or decreased barrier heights and the increased effective masses with pressure are the main reasons of the change in the pressure coefficients.

TUNNELING ESCAPE TIME OF ELECTRONS FROM A QUANTUM-WELL WITH GAMMA-X MIXING EFFECT

By using the envelope function method we calculated the tunneling escape time of electrons from a quantum well. We adopted a simplified interface matrix to describe the GAMMA-X mixing effect, and employed a wave packet method to determine the tunneling escape time. When the GAMMA state in the well was in resonance with the X state in the barrier, the escape time reduced remarkably. However, it was possible that the wave functions in two different channels, i.e., GAMMA-GAMMA-GAMMA and GAMMA-X-GAMMA, could interfere destructively, leading the escape time greater than that of pure GAMMA-GAMMA-GAMMA tunneling.

SIMULATION OF LATERAL CONFINEMENT IN VERY NARROW CHANNELS

A theoretical study is presented of the lateral confinement potential (CP) in the very narrow mesa channels fabricated in the conventional two-dimensional (2D) electron gas in GaAs-AlxGa1-xAs heterostructures. The ID electronic structures are calculated in the framework of the confinement potential: V(x) = m* omega0(2)x2/2 for Absolute value of x

LO-PHONON-ASSISTED TUNNELING IN ASYMMETRIC DOUBLE-WELL STRUCTURES WITH THICK BARRIERS

Nonresonant electron tunneling between asymmetric double quantum wells in AlxGa1-xAs/GaAs systems has been investigated by using steady-state and time-resolved photoluminescence spectra. Experimental evidence of LO-phonon-assisted tunneling through thick barriers has been obtained by enhancing excitation power densities or applying electric fields perpendicular to the well plane. LO-phonon-assisted tunneling times have also been estimated from the variation of the decay time of the narrow-well photoluminescence with applied electric fields. Our findings suggest that LO phonons in the barriers play an important role in the tunneling transfer.

CBE GROWTH OF GAAS/GAAS, GAAS/SI AND ALGAAS/GAAS USING TEG, ASH3 AND AMINE-ALANE PRECURSORS

The growth of high quality AlGaAs by CBE bas been limited by the high levels of carbon and oxygen contamination. The use of alane based precursors offers a significant reduction in such contamination. We report for the first time the CBE growth of AlxGa1-xAs from triethylgallium, dimethylethylamine-alane and arsine, and compare with. growth from triethylgallium, trimethylamine-alane and arsine. Some preliminary results of work on the CBE growth of GaAs on silicon will also be reported.

A NEW METHOD FOR MEASURING THE EFFECTIVE DIFFUSION CONSTANT OF 2-DIMENSIONAL ELECTRONS IN THE PRESENCE OF MAGNETIC-FIELDS

The transient charge response Q(t) of a two-dimensional electron gas (2DEG) in GaAs/AlxGa1-xAs heterostructures to a small pulse of the gate voltage, applied between the top gate and source electrodes in a Corbino structure, was employed to directly measure the effective diffusion constant of a 2DEG in the quantum Hall regime. The measured diffusion constant D showed a drastic change as the magnetic field was swept through the integer fillings of the Landau levels.

EFFECTIVE-MASS THEORY FOR SUPERLATTICES GROWN ON (11N)-ORIENTED SUBSTRATES

An effective-mass formulation for superlattices grown on (11N)-oriented substrates is given. It is found that, for GaAs/AlxGa1-xAs superlattices, the hole subband structure and related properties are sensitive to the orientation because of the large anisotropy of the valence band. The energy-level positions for the heavy hole and the optical transition matrix elements for the light hole apparently change with orientation. The heavy- and light-hole energy levels at k parallel-to = 0 can be calculated separately by taking the classical effective mass in the growth direction. Under a uniaxial stress along the growth direction, the energy levels of the heavy and light holes shift down and up, respectively; at a critical stress, the first heavy- and light-hole energy levels cross over. The energy shifts caused by the uniaxial stress are largest for the (111) case and smallest for the (001) case. The optical transition matrix elements change substantially after the crossover of the first heavy- and light-hole energy has occurred.

Growth of high-quality relaxed In0.3Ga0.7As/GaAs superlattices

With a low strained InxGa1-xAs/GaAs(x similar to 0.01) superlattice (SL) buffer layer, the crystal quality of 50 period relaxed In0.3Ga0.7As/GaAs strained SLs has been greatly improved and over 13 satellite peaks are observed from X-ray double-crystal diffraction, compared with three peaks in the sample without the buffer layer. Cross-section transmission electron microscopy reveals that the dislocations due to superlattice strain relaxation are blocked by the SLs itself and are buried into the buffer layer. The role of the SL buffer layer lies in that the number of the dislocations is reduced in two ways: (1) the island formation is avoided and (2) the initial nucleation of the threading dislocations is retarded by the high-quality growth of the SL buffer layer. When the dislocation pinning becomes weak as a result of the reduced dislocation density, the SLs can effectively move the threading dislocations to the edge of the wafer.

Self-formed InGaAs/GaAs quantum dot superlattice and direct observation on strain distribution in the capped superlattice

We have demonstrated a 20 period dislocation-free InGaAs/GaAs quantum dot superlattice which is self-formed by the strain from the superlattice taken as a whole rather than by the strain from the strained single layer. The island formation does not take place while growing the corresponding strained single layer. From the variation of the average dot height in each layer, the strain distribution and relaxation process in the capped superlattice have been examined. It is found that the strain is not uniformly distributed and the greatest strains occur at two interfaces between the superlattice and the substrate and the cap layer in the capped superlattice. (C) 1997 American Institute of Physics.

Characterization of deep centers in AlGaAs/InGaAs/GaAs pseudomorphic HEMT structures grown by molecular beam epitaxy and hydrogen treatment

In AlGaAs/InGaAs/GaAs PM-HEMT structures, the characterization of deep centers, the degradation in electrical and optical properties and their effects on electrical performance of the PM-HEMTs have been investigated by DLTS, SIMS, PL and conventional van der Pauw techniques. The experimental results confirm that the deep level centers correlate strongly with the oxygen content in the AlGaAs layer, the PL response of PM-HEMTs, and the electrical performance of the PM-HEMTs. Hydrogen plasma treatment was used to passivate/annihilate these centers, and the effects of hydrogenation were examined.

Deep centers in AlGaAs/GaAs GRIN-SCH SQW laser structures grown by MBE and MOCVD

The deep centers in AlGaAs/GaAs graded index-separate confinement heterostructure single quantum well (GRIN-SCHSQW) laser structures grown by MBE and MOCVD have been investigated using deep level transient spectroscopy (DLTS) technique, The majority and minority carrier DLTS spectra show that the deep (hole and electron) traps (Hi and E3), having large capture cross sections and concentrations, are observed in the graded n-AlxGa1-xAs layer of laser structures in addition to the well-known DX centers. For laser structures grown by MBE, the deep hole trap H1 and the deep electron trap E3 may be spatially localized in the interface regions of discontinuous variation Al mole fraction of the n-AlxGa1-xAs layer with x = 0.20-0.43. For laser structures grown by MOCVD, the deep electron trap E3 may be spatially localized in the n-AlxGa1-xAs layer with x = 0.18-0.30, and the DX center may be spatially localized in the interface regions of discontinuous variation Al mole fraction of the AlxGa1-xAs layer with x = 0.22-0.30.

High-pressure study of optical transitions in strained In0.2Ga0.8As/GaAs multiple quantum wells

We have measured low-temperature photoluminescence (PL) and absorption spectra of In0.2Ga0.8As/GaAs multiple quantum wells (MQW's) under hydrostatic pressures up to 8 GPa. In PL, only a single peak is observed below 4.9 GPa corresponding to the n = 1 heavy-hole (HH) exciton in the InxGa1-xAs wells. Above 4.9 GPa, new PL lines related to X-like conduction band states appear. They are assigned to the type-II transition from the X(Z) states in GaAs to the HH subband of the InxGa1-xAs wells and to the zero-phonon line and LO-phonon replica of the type-I transition involving the X(XY) valleys of the wells. In addition to absorption peaks corresponding to direct exciton transitions in the wells, a new strong absorption feature is apparent in spectra for pressures between 4.5 and 5.5 GPa. This absorption is attributed to the pseudodirect transition between the HH subband and the X, state of the wells. This gives clear evidence for an enhanced strength of indirect optical transitions due to the breakdown of translational invariance in MQW structures. From experimental level splittings we determine the valence band offset and the shear deformation potential for X states in the In0.2Ga0.8As layer.

A new structure of In-based ohmic contacts to n-type GaAs

Electrical, structural and reaction characteristics of In-based ohmic contacts to n-GaAs were studied. Attempts were made to form a low-band-gap interfacial phase of InGaAs to reduce the barrier height at the metal/semiconductor junction, thus yielding low-resistance, highly reliable contacts. The contacts were fabricated by e-beam sputtering Ni, NiIn and Ge targets on VPE-grown n(+)-GaAs film (approximate to 1 mu m, 2 x 10(18) cm(-3)) in ultrahigh vacuum as the structure of Ni(200 Angstrom)/NiIn(100 Angstrom)/Ge(40 Angstrom)/n(+)-GaAs/SI-GaAs, followed by rapid thermal annealing at various temperatures (500-900 degrees C). In this structure, a very thin layer of Ge was employed to play the role of heavily doping donors and diffusion limiters between In and the GaAs substrate. Indium was deposited by sputtering NiIn alloy instead of pure In in order to ensure In atoms to be distributed uniformly in the substrate; nickel was chosen to consume the excess indium and form a high-temperature alloy of Ni3In. The lowest specific contact resistivity (rho(c)) of (1.5 +/- 0.5)x 10(-6) cm(2) measured by the Transmission Line Method (TLM) was obtained after annealing at 700 degrees C for 10 s. Auger sputtering depth profile and Transmission Electron Microscopy (TEM) were used to analyze the interfacial microstructure. By correlating the interfacial microstructure to the electronical properties, InxGa1-xAs phases with a large fractional area grown epitaxially on GaAs were found to be essential for reduction of the contact resistance.