Research roadmap for green wireline access

The paper describes different research concepts of which the combination leads to an improvement of the power consumption per subscriber in a wireline access network by 10× and the energy efficiency per transferred bit by 100×. © 2012 IEEE.

Fiber-Optic Technologies for Wireline and Wireless In-building Networks

This doctoral dissertation aims to establish fiber-optic technologies overcoming the limiting issues of data communications in indoor environments. Specific applications are broadband mobile distribution in different in-building scenarios and high-speed digital transmission over short-range wired optical systems. Two key enabling technologies are considered: Radio over Fiber (RoF) techniques over standard silica fibers for distributed antenna systems (DAS) and plastic optical fibers (POFs) for short-range communications. Hence, the objectives and achievements of this thesis are related to the application of RoF and POF technologies in different in-building scenarios. On one hand, a theoretical and experimental analysis combined with demonstration activities has been performed on cost-effective RoF systems. An extensive modeling on modal noise impact both on linear and non-linear characteristics of RoF link over silica multimode fiber has been performed to achieve link design rules for an optimum choice of the transmitter, receiver and launching technique. A successful transmission of Long Term Evolution (LTE) mobile signals on the resulting optimized RoF system over silica multimode fiber employing a Fabry-Perot LD, central launch technique and a photodiode with a built-in ball lens was demonstrated up to 525m with performances well compliant with standard requirements. On the other hand, digital signal processing techniques to overcome the bandwidth limitation of POF have been investigated. An uncoded net bit-rate of 5.15Gbit/s was obtained on a 50m long POF link employing an eye-safe transmitter, a silicon photodiode, and DMT modulation with bit and power loading algorithm. With the insertion of 3x2N quadrature amplitude modulation constellation formats, an uncoded net-bit-rate of 5.4Gbit/s was obtained on a 50 m long POF link employing an eye-safe transmitter and a silicon avalanche photodiode. Moreover, simultaneous transmission of baseband 2Gbit/s with DMT and 200Mbit/s with an ultra-wideband radio signal has been validated over a 50m long POF link.

Modeling Finite Buffer Effects on TCP Traffic over an IEEE 802.11 Infrastructure WLAN

The network scenario is that of an infrastructure IEEE 802.11 WLAN with a single AP with which several stations (STAs) are associated. The AP has a finite size buffer for storing packets. In this scenario, we consider TCP controlled upload and download file transfers between the STAs and a server on the wireline LAN (e.g., 100 Mbps Ethernet) to which the AP is connected. In such a situation, it is known (see, for example, (3), [9]) that because of packet loss due to finite buffers at the Ap, upload file transfers obtain larger throughputs than download transfers. We provide an analytical model for estimating the upload and download throughputs as a function of the buffer size at the AP. We provide models for the undelayed and delayed ACK cases for a TCP that performs loss recovery only by timeout, and also for TCP Reno.

Experiences With WM: A Centralised Scheduling Approach for Performance Management of IEEE 802.11 Wireless LANs

In our earlier work ([1]) we proposed WLAN Manager (or WM) a centralised controller for QoS management of infrastructure WLANs based on the IEEE 802.11 DCF standards. The WM approach is based on queueing and scheduling packets in a device that sits between all traffic flowing between the APs and the wireline LAN, requires no changes to the AP or the STAs, and can be viewed as implementing a "Split-MAC" architecture. The objectives of WM were to manage various TCP performance related issues (such as the throughput "anomaly" when STAs associate with an AP with mixed PHY rates, and upload-download unfairness induced by finite AP buffers), and also to serve as the controller for VoIP admission control and handovers, and for other QoS management measures. In this paper we report our experiences in implementing the proposals in [1]: the insights gained, new control techniques developed, and the effectiveness of the WM approach in managing TCP performance in an infrastructure WLAN. We report results from a hybrid experiment where a physical WM manages actual TCP controlled packet flows between a server and clients, with the WLAN being simulated, and also from a small physical testbed with an actual AP.

Modeling finite buffer effects on TCP traffic over an IEEE 802.11 infrastructure WLAN

The network scenario is that of an infrastructure IEEE 802.11 WLAN with a single AP with which several stations (STAs) are associated. The AP has a finite size buffer for storing packets. In this scenario, we consider TCP-controlled upload and download file transfers between the STAs and a server on the wireline LAN (e.g., 100 Mbps Ethernet) to which the AP is connected. In such a situation, it is well known that because of packet losses due to finite buffers at the AP, upload file transfers obtain larger throughputs than download transfers. We provide an analytical model for estimating the upload and download throughputs as a function of the buffer size at the AP. We provide models for the undelayed and delayed ACK cases for a TCP that performs loss recovery only by timeout, and also for TCP Reno. The models are validated incomparison with NS2 simulations.

Reconfigurable Viterbi decoder on mesh connected multiprocessor architecture

In modern wireline and wireless communication systems, Viterbi decoder is one of the most compute intensive and essential elements. Each standard requires a different configuration of Viterbi decoder. Hence there is a need to design a flexible reconfigurable Viterbi decoder to support different configurations on a single platform. In this paper we present a reconfigurable Viterbi decoder which can be reconfigured for standards such as WCDMA, CDMA2000, IEEE 802.11, DAB, DVB, and GSM. Different parameters like code rate, constraint length, polynomials and truncation length can be configured to map any of the above mentioned standards. Our design provides higher throughput and scalable power consumption in various configuration of the reconfigurable Viterbi decoder. The power and throughput can also be optimized for different standards.

Architecture of Run-time Reconfigurable Channel Decoder

Modern wireline and wireless communication devices are multimode and multifunctional communication devices. In order to support multiple standards on a single platform, it is necessary to develop a reconfigurable architecture that can provide the required flexibility and performance. The Channel decoder is one of the most compute intensive and essential elements of any communication system. Most of the standards require a reconfigurable Channel decoder that is capable of performing Viterbi decoding and Turbo decoding. Furthermore, the Channel decoder needs to support different configurations of Viterbi and Turbo decoders. In this paper, we propose a reconfigurable Channel decoder that can be reconfigured for standards such as WCDMA, CDMA2000, IEEE802.11, DAB, DVB and GSM. Different parameters like code rate, constraint length, polynomials and truncation length can be configured to map any of the above mentioned standards. A multiprocessor approach has been followed to provide higher throughput and scalable power consumption in various configurations of the reconfigurable Viterbi decoder and Turbo decoder. We have proposed A Hybrid register exchange approach for multiprocessor architecture to minimize power consumption.

Nonneutral network and the role of bargaining power in side payments

Representatives of several Internet access providers have expressed their wish to see a substantial change in the pricing policies of the Internet. In particular, they would like to see content providers pay for use of the network, given the large amount of resources they use. This would be in clear violation of the �network neutrality� principle that had characterized the development of the wireline Internet. Our first goal in this paper is to propose and study possible ways of implementing such payments and of regulating their amount. We introduce a model that includes the internaut�s behavior, the utilities of the ISP and of the content providers, and the monetary flow that involves the internauts, the ISP and content provider, and in particular, the content provider�s revenues from advertisements. We consider various game models and study the resulting equilibrium; they are all combinations of a noncooperative game (in which the service and content providers determine how much they will charge the internauts) with a cooperative one - the content provider and the service provider bargain with each other over payments to one another. We include in our model a possible asymmetric bargaining power which is represented by a parameter (that varies between zero to one). We then extend our model to study the case of several content providers. We also provide a very brief study of the equilibria that arise when one of the content providers enters into an exclusive contract with the ISP.

On the feasibility of network alignment for three-source three-destination Multiple Unicast networks with delays

A transform approach to network coding was in-troduced by Bavirisetti et al. (arXiv:1103.3882v3 [cs.IT]) as a tool to view wireline networks with delays as k-instantaneous networks (for some large k). When the local encoding kernels (LEKs) of the network are varied with every time block of length k >1, the network is said to use block time varying LEKs. In this work, we propose a Precoding Based Network Alignment (PBNA) scheme based on transform approach and block time varying LEKs for three-source three-destination multiple unicast network with delays (3-S3-D MUN-D). In a recent work, Menget al. (arXiv:1202.3405v1 [cs.IT]) reduced the infinite set of sufficient conditions for feasibility of PBNA in a three-source three-destination instantaneous multiple unicast network as given by Das et al. (arXiv:1008.0235v1 [cs.IT]) to a finite set and also showed that the conditions are necessary. We show that the conditions of Meng et al. are also necessary and sufficient conditions for feasibility of PBNA based on transform approach and block time varying LEKs for 3-S3-D MUN-D.

Regulation of Off-Network Pricing in a Nonneutral Network

Representatives of several Internet service providers (ISPs) have expressed their wish to see a substantial change in the pricing policies of the Internet. In particular, they would like to see content providers (CPs) pay for use of the network, given the large amount of resources they use. This would be in clear violation of the ``network neutrality'' principle that had characterized the development of the wireline Internet. Our first goal in this article is to propose and study possible ways of implementing such payments and of regulating their amount. We introduce a model that includes the users' behavior, the utilities of the ISP and of the CPs, and, the monetary flow that involves the content users, the ISP and CP, and, in pUrticular, the CP's revenues from advertisements. We consider various game models and study the resulting equilibria; they are all combinations of a noncooperative game (in which the ISPs and CPs determine how much they will charge the users) with a ``cooperative'' one on how the CP and the ISP share the payments. We include in our model a possible asymmetric weighting parameter (that varies between zero to one). We also study equilibria that arise when one of the CPs colludes with the TSP. We also study two dynamic game models as well as the convergence of prices to the equilibrium values.

Protection of Digital Telecom Exchanges Against Lightning Surges and Earth Faults

Low-power electronic devices used in digital telecom exchanges are vulnerable to surge voltages and currents primarily originating from natural lightning or due to the direct interactions between electric power and telecommunication lines, etc., causing the earth/ground potential rise, neutral potential rise, and faults in the system. The fault currents may flow directly to telecom lines or through the equipment to the customer's premises, causing adequate damage to the equipment and personnel safety. In wireline applications, analog or digital, central office, exchanges, and subscriber sides have to be protected. Decisive protection and protective methods have to be employed for proper functioning of the equipment under overvoltage/overcurrent conditions. Current investigation reports some interesting results obtained on the recently developed high-voltage high-current protection cards used in digital telecom exchanges. The performances of protection cards both for the ring wave and hybrid wave surges are evaluated and presented. The surge generators required for the investigation are developed and fabricated in house as per the relevant telecom standards.

Integração de dados geofísicos de poços e geoquímicos na avaliação do potencial gerador dos folhelhos betuminosos da Formação Tremembé, Bacia de Taubaté

Nos depósitos cenozóicos da Bacia de Taubaté são encontrados depósitos de folhelhos betuminosos (oleígenos) pertencentes à Formação Tremembé, de idade oligocênica, que durante alguns anos na década de 50 foram investigados com relação ao seu aproveitamento econômico através da extração industrial do óleo nele contido. Entretanto, em face de aspectos tecnológicos e conjunturais da época, esse aproveitamento industrial foi considerado inviável do ponto de vista econômico. Nesta dissertação é proposta uma aplicação da perfilagem geofísica para a caracterização da faciologia dos folhelhos betuminosos da Formação Tremembé, tendo como objetivo principal a identificação das eletrofácies nos perfis elétricos, através de uma metodologia robusta e consistente. A identificação de eletrofácies é importante para ajudar na determinação da caracterização de uma reserva não convencional e na análise da viabilidade econômica. Neste estudo foram utilizados os perfis convencionais de poço: Raio gama, resitividade, potencial espontâneo e sônico. Os dados de perfis de poços foram integrados com os testemunhos e dados geoquímicos, mais precisamente os dados de COT, S, IH, S2 para uma caracterização realística das eletrofácies. Os dados foram obtidos a partir de três sondagens rotativas realizadas na Bacia de Taubaté, resultantes de testemunhagem contínua e perfilagem a cabo ao longo do intervalo de folhelhos da Formação Tremembé. A partir disto, obtém-se como resposta um modelo específico para cada litologia, onde cada pico corresponde a uma eletrofácies, permitindo o estabelecimento de alguns padrões ou assinaturas geofísicas para as principais fácies ocorrentes. Como resultado deste trabalho, foi possível correlacionar as eletrofácies entre os poços numa seção modelo, a partir de similaridade lateral das eletrofácies entre os marcos estratigráficos representado, foi possível observar a continuidade de duas sequências de folhelhos betuminoso com alto teores de COT, S, IH, S2, considerados os mais importantes do ponto de vista econômico e gerado um modelo faciológico 2D e 3D dessas camadas. Os resultados obtidos neste trabalho são bastante promissores, apontando para a possibilidade de aplicação desta técnica a outros poços da Bacia de Taubaté, fornecendo subsídios relevantes à determinação da evolução sedimentar.

Nova metodologia para caracterização litológica das rochas carbonáticas do pré-sal com base na perfilagem e espectroscopia de poço

O cenário mundial de crescimento está favorecendo uma demanda cada vez maior por petróleo e gás. Para se adequar a esta demanda crescente, as companhias petroleiras têm perfurado em regiões de águas profundas e com caráter geológico particular, como os depósitos carbonáticos recém explorados no Brasil pela Petrobras e que entraram em produção a partir de 2008. Para a produção de hidrocarbonetos é preciso um conhecimento profundo das rochas que os contém. Isto se deve ao fato que os sensores usados para detectar hidrocarbonetos no processo conhecido como perfilagem de poço na indústria petroleira são influenciados em suas medições pelas características das rochas. No caso deste trabalho, carbonatos do pré-sal, aparece uma complicação adicional em termos litológicos que é a presença do mineral Estevensita que não é comumente encontrado em ambientes carbonáticos. Em função de não haver uma forma de detectar sem ambiguidades o mineral Estevensita (rico em magnésio) com a Dolomita (também rica em magnésio), e levando-se em consideração o fato de que a Estevensita fecha os poros da rocha (rocha não reservatório) enquanto a Dolomita normalmente pode ser uma excelente rocha reservatório é de fundamental importância conhecer se o magnésio é proveniente da Estevensita ou do processo de dolomitização do carbonato (substituição de cálcio por magnésio). Não existe hoje em dia uma metodologia de perfilagem de poço que possa indicar a proveniência do magnésio. Estevensita ou Dolomita? Rocha reservatório ou não-reservatório? O objetivo deste trabalho é prover respostas às perguntas acima. Desenvolver uma forma de analisar os minerais presentes no pré-sal através da perfilagem e espectroscopia de poço e fazer a separação entre os diversos constituintes das rochas encontradas no pré-sal. O pré-sal brasileiro é constituído por litologia carbonática complexa, sendo a seção rifte formada por coquinas e a seção sag por microbialitos. Estas rochas foram depositadas antes da deposição da camada de sal no fim do Aptiano. Para atingir o resultado esperado neste trabalho serão utilizadas medições convencionais e não convencionais no laboratório com rochas análogas ao pré-sal e minerais puros tais como a Estevensita a fim de determinar respostas padrão para serem utilizados em programas de análise de registros de perfilagem. O produto final deste trabalho é desenvolver um procedimento para determinação de litologia no pré-sal brasileiro através de registros a cabo (wireline) ou enquanto se perfura (Logging While Drilling - LWD)

鄂尔多斯盆地子洲气田二叠系山西组储层特征与天然气富集规律研究

In this thesis, detailed studies on the sedimentology and petrophysical properties of reservoir rocks in the Shan#2 Member of Shanxi Formation, Zizhou gas field of Ordos Basin, are carried out, based on outcrop description, core description, wireline log interpretation and analysis of petrophysical properties. In the context of stratigraphic division scheme of the Upper Paleozoic in Ordos Basin, the Shan#2 Member is further divided into three subintervals: the Shan#23, Shan#22 and Shan#21, based on the marker beds，depositional cycles, wireline log patterns. Subaqueous deltaic-front distributary channels, distributed from the south to north, is identified，which is the main reservoir sand bodies for gases of Shan#2 Member at Zizhou gas field. Quartzose and lithic-quartzose sandstones, commonly with a high volume of cement, but a low volume of matrix, are the major reservoir rocks in the studied area. All sandstones have been evolved into the late diagenetic stage (referred to as diagenetic stage B) during the burial, experiencing compaction, cementation, replacement and dissolution, in which the compaction and cementation could have reduced the porosity, while dissolution could have improved the petrophysical properties. The pore types in the reservoirs are dominated by intergranular-solutional, intergranular-intercrystal and intercrystal-solutional porosity. According to the parameters and capillary pressure curves of test samples, five types of pore texture (I-V) are differentiated, in which types II and III pore textures displayed by low threshold pressure-wide pore throat and moderate threshold pressure-moderately wide pore throat, exist widespread. Sandstone reservoirs in the studied area are characterized by exceptionally low porosity and permeability, in which the petrophysical properties of those in Shan#23 horizon are relatively better. The petrophysical property of reservoirs was influenced both by the sedimentation and diagenesis. In general, the coarse quartzose sandstones deposited in subaqueous distributary channels show the best petrophysical property, which tends to be worse as the grain size decreases and lithic amount increases. Three types of gas reservoirs in Shan#23 horizon are classified according to petrophysical properties (porosity and permeability), which could have been influenced by the initial depositional facies, diagenesis and tectonics. On the basis of the study on the geological conditions of reservoirs in the area, it is concluded that sedimetary facies, diagenesis and tectonic actions can provide an important foundation for gas pool formation, which can also control the accumulation and distribution of gas reservoirs.

苏里格气田苏6加密井区山1-盒8层段河流沉积体系分析

Sulige gas field is located in Northwest of Yi-Shan Slope of the Ordos Basin. The Shan 1 Member of the Shanxi Formation and He8 Member of the ShiHeZi Formation are not only objective strata of research but also main producing strata of the Sulige Field. From core and wireline log data of 32 wells in well Su6 area of Sulige field, no less than six lithofaice types can be recognised. They are Gm,Sl,Sh,Sm,Sp,Fl,Fm. Box-shaped, bell-shaped, funnel-shaped and line-segment-shaped log are typcial gamma-ray log characters and shapes. The Depositonal system of the Shan1-He8 strata in research area have five bounding-surface hierarchies and was composed of six architectural elements, CH, LS,FF（CH）,SB,LA,GB. The depositional model of Shan 1 was the type of a sandy meandering river with natural levee, abandoned channels and crevasse splay. Channel depth of this model maybe 7-12 m and the fullest-bank flow can reach 14 m high. Based on analysis of depositional causes, a sandy braided river model for the depositional system of He 8 can be erected. It consists of active main channels, active chute channels, sheet-like sand bars, abandoned main channels and abandoned chute channels. Channel depth of this model can be 3-4 m with 9 m of highest flow. Six gamma-ray log cross sections show that the connectivity of sandbodies through Shan 1 Member is lower than He 8. Influenced by occurrence of mudy and silty deposits, vertical connectivity of sandbodies through He 8 is not high.