Polyolefin fibre-reinforced concrete : from material behaviour to numerical and design considerations

La presente Tesis proporciona una gran cantidad de información con respecto al uso de un nuevo y avanzado material polimérico (con base de poliolefina) especialmente adecuada para ser usada en forma de fibras como adición en el hormigón. Se han empleado fibras de aproximadamente 1 mm de diámetro, longitudes entre 48 y 60 mm y una superficie corrugada. Las prometedoras propiedades de este material (baja densidad, bajo coste, buen comportamiento resistente y gran estabilidad química) justifican el interés en desarrollar el esfuerzo de investigación requerido para demostrar las ventajas de su uso en aplicaciones prácticas. La mayor parte de la investigación se ha realizado usando hormigón autocompactante como matriz, ya que este material es óptimo para el relleno de los encofrados del hormigón, aunque también se ha empleado hormigón normal vibrado con el fin de comparar algunas propiedades. Además, el importante desarrollo del hormigón reforzado con fibras en los últimos años, tanto en investigación como en aplicaciones prácticas, también es muestra del gran interés que los resultados y consideraciones de diseño que esta Tesis pueden tener. El material compuesto resultante, Hormigón Reforzado con Fibras de Poliolefina (HRFP o PFRC por sus siglas inglesas) ha sido exhaustivamente ensayado y estudiado en muchos aspectos. Los resultados permiten establecer cómo conseguidos los objetivos buscados: -Se han cuantificado las propiedades mecánicas del PFRC con el fin de demostrar su buen comportamiento en la fase fisurada de elementos estructurales sometidos a tensiones de tracción. -Contrastar los resultados obtenidos con las bases propuestas en la normativa existente y evaluar las posibilidades para el uso del PFRC con fin estructural para sustituir el armado tradicional con barras de acero corrugado para determinadas aplicaciones. -Se han desarrollado herramientas de cálculo con el fin de evaluar la capacidad del PFRC para sustituir al hormigón armado con las barras habituales de acero. -En base a la gran cantidad de ensayos experimentales y a alguna aplicación real en la construcción, se han podido establecer recomendaciones y consejos de diseño para que elementos de este material puedan ser proyectados y construidos con total fiabilidad. Se presentan, además, resultados prometedores en una nueva línea de trabajo en el campo del hormigón reforzado con fibras combinando dos tipologías de fibras. Se combinaron fibras de poliolefina con fibras de acero como refuerzo del mismo hormigón autocompactante detectándose sinergias que podrían ser la base del uso futuro de esta tecnología de hormigón. This thesis provides a significant amount of information on the use of a new advanced polymer (polyolefin-based) especially suitable in the form of fibres to be added to concrete. At the time of writing, there is a noteworthy lack of research and knowledge about use as a randomly distributed element to reinforce concrete. Fibres with an approximate 1 mm diameter, length of 48-60 mm, an embossed surface and improved mechanical properties are employed. The promising properties of the polyolefin material (low density, inexpensive, and with good strength behaviour and high chemical stability) justify the research effort involved and demonstrate the advantages for practical purposes. While most of the research has used self-compacting concrete, given that this type of matrix material is optimum in filling the concrete formwork, for comparison purposes standard vibration compacted mixes have also been used. In addition, the interest in fibre-reinforced concrete technology, in both research and application, support the significant interest in the results and considerations provided by the thesis. The resulting composite material, polyolefin fibre reinforced concrete (PFRC) has been extensively tested and studied. The results have allowed the following objectives to be met: -Assessment of the mechanical properties of PFRC in order to demonstrate the good performance in the post-cracking strength for structural elements subjected to tensile stresses. -- Assessment of the results in contrast with the existing structural codes, regulations and test methods. The evaluation of the potential of PFRC to meet the requirements and replace traditional steel-bar reinforcement applications. -Development of numerical tools designed to evaluate the capability of PFRC to substitute, either partially or totally, standard steel reinforcing bars either alone or in conjunction with steel fibres. -Provision, based on the large amount of experimental work and real applications, of a series of guidelines and recommendations for the practical and reliable design and use of PFRC. Furthermore, the thesis also reports promising results about an innovative line in the field of fibre-reinforced concrete: the design of a fibre cocktail to reinforce the concrete by using two types of fibres simultaneously. Polyolefin fibres were combined with steel fibres in self-compacting concrete, identifying synergies that could serve as the base in the future use of fibre-reinforced concrete technology.

Rapport M/L de disques de galaxies issus de modèles CSPE et contrôle des contraintes mécaniques dans la conception de revêtements optiques

La thèse qui suit est organisée en deux volets: un premier volet portant sur les modèles de masse de galaxies et un second volet sur la conception de revêtements optiques et le contrôle de leurs propriétés mécaniques. Les modèles de masse présentés dans cette thèse ont été réalisés sur un sous-échantillon de dix galaxies de l'étude SINGS comprenant neuf galaxies normales et une galaxie naine. Ce travail visait à fixer le rapport masse-luminosité du disque à tout rayon en utilisant les résultats de modèles d'évolution galactique chimio-spectrophotométriques ajustés spécifiquement à chaque galaxie grâce à son profil de photométrie multi-bandes. Les résultats montrent que les disques stellaires tels que normalisés par les rapports masse-luminosité issus des modèles ont des masses cohérentes dans toutes les bandes étudiées de l'ultra-violet, du visible ainsi que du proche infrarouge (bandes FUV à IRAC2). Ces disques peuvent être considérés comme maximaux par rapport aux données cinématiques des galaxies étudiées. Ceci est dû au fait que le rapport M/L est plus élevé au centre que sur les bords. Les disques étant maximaux et physiquement justifiés, on ne peut dès lors ignorer les effets de composants tels que les bulbes ou les barres et les corrections nécessaires doivent être apportées aux profils de luminosité et de vitesses de rotation de la galaxie. Dans les travaux de la seconde partie, le logiciel en développement libre OpenFilters a été modifié afin de tenir compte des contraintes mécaniques dans la conception numérique de revêtements optiques. Les contraintes mécaniques dans les couches minces ont un effet délétère sur leurs performances optiques. Un revêtement destiné à rendre réflectives les lames d'un étalon Fabry-Perot utilisé en astronomie a été conçu et fabriqué afin d'évaluer les performances réelles de la méthode. Ce cas a été choisi à cause de la diminution de la finesse d'un étalon Fabry-Perot apporté par la courbure des lames sous l'effet des contraintes. Les résultats montrent que les mesures concordent avec les modèles numériques et qu'il est donc possible à l'aide de ce logiciel d'optimiser les revêtements pour leur comportement mécanique autant que pour leurs propriétés optiques.

Improved design rules for fixed ended cold-formed steel columns subject to flexural-torsional buckling

This paper has presented the details of an investigation into the flexural and flexuraltorsional buckling behaviour of cold-formed structural steel columns with pinned and fixed ends. Current design rules for the member capacities of cold-formed steel columns are based on the same non-dimensional strength curve for both fixed and pinned-ended columns. This research has reviewed the accuracy of the current design rules in AS/NZS 4600 and the North American Specification in determining the member capacities of cold-formed steel columns using the results from detailed finite element analyses and an experimental study of lipped channel columns. It was found that the current Australian and American design rules accurately predicted the member capacities of pin ended lipped channel columns undergoing flexural and flexural torsional buckling. However, for fixed ended columns with warping fixity undergoing flexural-torsional buckling, it was found that the current design rules significantly underestimated the column capacities as they disregard the beneficial effect of warping fixity. This paper has therefore proposed improved design rules and verified their accuracy using finite element analysis and test results of cold-formed lipped channel columns made of three cross-sections and five different steel grades and thicknesses.

Design and properties analysis of multi-layer dielectric used in pulse compressor gratings

Used in chirped-pulse amplification system and based on multi-layer thin film stack, pulse compressor gratings (PCG) are etched by ion-beam and holographic techniques. Diffraction efficiency and laser-induced damage threshold rely on the structural parameters of gratings. On the other hand, they depend greatly on the design of multi-layer. A theoretic design is given for dielectric multi-layer, which is exposed at 413.1 nm and used at 1053 nm. The influences of coating design on optical characters are described in detail. The analysis shows that a coating stack of H3L (H2L) (boolean AND) 9H0.5L2.01H meets the specifications of PCG well. And there is good agreement of transmission between experimental and the theoretic design. (c) 2005 Elsevier GmbH. All rights reserved.

Delay of the excited state lasing of 1310 nm InAs/GaAs quantum dot lasers by facet coating

In this letter, we present a facet coating design to delay the excited state (ES) lasing for 1310 nm InAs/GaAs quantum dot lasers. The key point of our design is to ensure that the mirror loss of ES is larger than that of the ground state by decreasing the reflectivity of the ES. In the facet coating design, the central wavelength is at 1480 nm, and the high- and low-index materials are Ta2O5 and SiO2, respectively. Compared with the traditional Si/SiO2 facet coating with a central wavelength of 1310 nm, we have found that with the optimal design the turning temperature of the ES lasing has been delayed from 90 to 100 degrees C for the laser diodes with cavity length of 1.2 mm. Furthermore, the characteristic temperature (T-0) of the laser diodes is also improved.

Sustainable concrete: design and testing

Producing concrete with secondary raw materials is an excellent way to contribute to a moresustainable world, provided that this concrete has at least the same performance during itsservice life as concrete made with the primary raw materials it replaces. Secondary rawmaterials for Light Weight (LW) aggregates (rigid polyurethane foams, shredded tire rubberand mixed plastic scraps) have been combined with secondary raw materials for the binder(fly ash, slag and perlite tailings) making sustainable concretes that were investigated fortheir suitability as LW, highly insulating concrete for four different types of applications.Compliance to desired engineering properties (workability, setting time) was not alwaysfeasible: it was mostly the low workability of the mixtures that limited their application.Contrary to well established cements, steering the workability by adding water was not anoption for these binders that rely on alkali-activation. Eight successful mixtures have beentested further. The results have shown that it is possible to produce a non-structuralsustainable concrete with good mechanical and thermal insulation properties.Design of concrete made with novel materials is currently not feasible without extensiveexperimentation as no design rules exist other than empirically derived rules based ontraditional materials. As a radical different approach, a flexible concrete mix design has beendeveloped with which the concrete can be modelled in the fresh and hardened state. Thenumerical concrete mix design method proves a promising tool in designing concrete forperformance demands such as elasticity parameters and thermal conductivity

Collaborative design procedures for architects and engineers

This book argues for novel strategies to integrate engineering design procedures and structural analysis data into architectural design. Algorithmic procedures that recently migrated into the architectural practice are utilized to improve the interface of both disciplines. Architectural design is predominately conducted as a negotiation process of various factors but often lacks rigor and data structures to link it to quantitative procedures. Numerical structural design on the other hand could act as a role model for handling data and robust optimization but it often lacks the complexity of architectural design. The goal of this research is to bring together robust methods from structural design and complex dependency networks from architectural design processes. The book presents three case studies of tools and methods that are developed to exemplify, analyze and evaluate a collaborative work flow.

Laser conditioning of ZrO2 : Y2O3/SiO2 mirror coatings prepared by E-beam evaporation

Laser conditioning effects of the dielectric mirror coatings with different designs were investigated. Simple quarter-wave ZrO2:Y2O3/SiO2 mirrors and half-wave SiO2 over-coated ZrO2:Y2O3/SiO2 mirror coatings were fabricated by E-beam evaporation (EBE). The absorbance of the samples before and after laser conditioning was measured by surface thermal lensing (STL) technology and the defects density was detected under Nomarski microscope. The enhancement of the laser damage resistance was found after laser conditioning. The dependence of the laser conditioning on the coating design was also observed and the over-coated sample obtained greatest enhancement, whereas the absorbance of the samples did not change obviously. During the sub-threshold fluence raster scanning, the minor damage about defects size was found and the assumption of pre-damage mechanism, based on the functional damage concept, was put forward. The improvement of the laser induced damage threshold (LIDT) was attributed to the benign damage of the defects and the dependence on the coating design owed to the damage growth behavior of different coating designs. (C) 2004 Elsevier B.V. All rights reserved.

利用等效层的消偏振宽带减反膜设计

分析了倾斜入射条件下导致光学薄膜产生偏振的原因, 针对不同偏振态的等效导纳与等效相位进行了分析, 并计算了对称膜层在45°入射条件下不同偏振态的等效折射率与等效相位厚度, 采用等效层方法设计了光学性能良好的600～900 nm波段消偏振宽带减反膜。最后利用电子束蒸发技术制备了薄膜样品, 样品的光谱性能完全能够满足使用要求。其中在600～900 nm波段范围内, 平均反射率均小于1.38%, 反射率的偏振度均低于0.89％。另外, 通过对其理论及实验光学性能、角度敏感性、膜层厚度误差敏感性等方面的分析结果可

三硼酸锂晶体上1064 nm, 532 nm, 355 nm三倍频增透膜的设计

采用矢量法设计了三硼酸锂晶体上1064 nm、532 nm和355 nm三倍频增透膜,结果表明1064 nm、532 nm和355 nm波长的剩余反射率分别为0.0017％、0.0002％和0.0013％。根据误差分析,薄膜制备时沉积速率精度控制在＋5.5％时,1064 nm、532 nm和355 nm波长的剩余反射率分别增加至0.20％、0.84％和1.89％。当材料折射率的变化控制在＋3％时,1064 nm处的剩余反射率增大为0.20％,532 nm和355 nm处分别达0.88％和0.24％。与薄膜

LiB3O5晶体上四倍频增透膜设计

采用矢量法设计了三硼酸锂（LiB3O5，LBO）晶体上1064nm、532nm、355nm和266nm四倍频增透膜．结果表明，在1064nm、532nm、355nm和266nm波长的剩余反射率分别为0．0019％、0．0031％、0．0061％和0．0047％．根据容差分析，薄膜制备时沉积速率准确度控制在＋6．5％时，基频、二倍频、三倍频和四倍频波长的剩余反射率分别增加至0．24％、0．92％、2．38％和4．37％．当薄膜材料折射率的变化控制在＋3％时，1064nm波长的剩余反射率增大为0．18％，532nm、355nm和266nm波长分别达0．61％，0．59％，0．20％．与薄膜物理厚度相比，膜层折射率对剩余反射率的影响大．对膜系敏感层的分析表明，在1064nm和266nm波长，从入射介质向基底过渡的第二层膜厚度变化对剩余反射率的影响最大，其次是第一膜层．在532nm和355nm波长，从入射介质向基底过渡的第一和第四膜层是该膜系的敏感层．误差分析也表明，薄膜材料的色散对特定波长的剩余反射率具有明显影响，即1064nm、532nm、355nm和266nm波长的剩余反射率分别增加至0．30％、0．23％、0．58％和3．13％．

O desenho da comunicação como conhecimento

As últimas décadas do séc. XX assistiram a um crescente protagonismo do Design de Informação que, desde então, tem sofrido inúmeras formas e designações, num processo de afirmação e auto descoberta. A proliferação de dados disponíveis deu ao design e em particular a este ramo do desenho para a compreensão, uma visibilidade crescente e a responsabilidade de encontrar, a partir da informação, novos meios para a construção de sentido. Do design à engenharia informática, são várias as disciplinas que convergem hoje nesse desígnio ainda que sob diferentes modelos e ferramentas. Esta convergência promove uma comparação entre modelos, que tendem a ser tanto mais valorizados quanto mais objectivas as representações. De Playfair a Bertin, as representações gráficas dos últimos duzentos anos têm-se situado no âmbito de disciplinas como a Economia, Sociologia ou a Gestão, explorando metáforas funcionais com vista à evidência da tradução numérica. O Design, enquanto mediador cultural e através do Desenho, tende a acrescentar ao mesmo exercício uma dimensão narrativa ou ilustrativa, convocando a própria existência do autor na interpretação dos mesmos dados numéricos. Com esta investigação, novos processos de semiose se oferecem, associando à objectividade dos dados quantitativos, a subjectividade da cultura formulada a partir do indivíduo enquanto intérprete. Na procura do conhecimento, reconhece-se assim que o desenho da informação ganha competências pela mediação da experiência, religando ética, técnica e estética.

Synthesis of broadband anti-reflection coatings for spaceflight infrared optics

A synthesis method is outlined for the design of broadband anti-reflection coatings for use in spaceborne infrared optics. The Golden Section optimisation routine is used to make a search, using designated non-absorptive dielectric thin film combinations, for the coating design which fulfils the required spectral requirements using the least number of layers and different materials. Three examples are given of coatings designed by this method : (I) 1µm to 12µm anti-reflection coating on Zinc Sulphide using Zinc Sulphide and Yttrium Fluoride thin film materials. (ii) 2µm to 14µm anti-reflection coating on Germanium using Germanium and Ytterbium Fluoride thin film materials. (iii) 6µm to 17µm anti-reflection coating on Germanium using Lead Telluride, Zinc Selenide and Barium Fluoride. The measured spectral performance of the manufactured 6µm to 17µm coating on Germanium is given. This is the anti-reflection coating for the germanium optics in the NASA Cassini Orbiter CIRS instrument.