Heating control of an electrical motor

Electrical motors on a ship attackable to different factors which decrease these lifetimes. One of the main external factors on a ship which usually is a reason of the motor failure is a moisture condensation which decreases the motor winding insulation and increase a probability of the short circuit. Therefore, the protection against moisture is necessary for ship electrical motors. The motor should be protected against moisture all time when it does not operate. The necessity of such protection requires a lot of energy consumption. This master’s thesis is focused on the creation of the electrical motor thermal model and on the different methods of the motor protection against moisture analysis with energy consumption point of view.

Standardized electrical tests for electrical equipment in road vehicles Case: Visedo Oy PowerMASTER M-frame

Electrical road vehicles were common at the begin of the 20th century but internal combustion engines took a victory from electrical motors in road vehicles. The acknowledgement of the environment, and the price and the availability of the crude oil are reasons for the comeback of the electrical vehicles. Advancement in industrial technology and political atmosphere in EU as the directive 20--20--20, which consists of reducing fossil emission, increasing renewable energy and increasing the energy efficiency, have made the electrification popular again. In this thesis tests based on standard ISO 16750--2 electrical loads for electrical equipment in road vehicles are made for Visedo Oy's PowerMASTER M-frame power electronics device. This device is designed for mainly drive trains in mobile work machines and marine vessels but can be used in other application in its power range which also includes road vehicles. The functionality of the device is tested with preliminary tests which act as a framework for the tests based on standards.

Power Factor Calculation by the Finite Element Method

The use of finite element analysis (FEA) to design electrical motors has increased significantly in the past few years due the increasingly better performance of modern computers. Even though the analytical software remains the most used tool, the FEA is widely used to refine the analysis and gives the final design to be prototyped. The power factor, a standard data of motor manufactures data sheet is important because it shows how much reactive power is consumed by the motor. This data becomes important when the motor is connected to network. However, the calculation of power factor is not an easy task. Due to the saturation phenomena the input motor current has a high level of harmonics that cannot be neglected. In this work the FEA is used to evaluate a proposed (not limitative) methodology to estimate the power factor or displacement factor of a small single-phase induction motor. Results of simulations and test are compared.

A new technique to control brushless motor for blood pump application

This article presents a back-electromotive force (BEMF)-based technique of detection for sensorless brushless direct current motor (BLDCM) drivers. The BLDCM has been chosen as the energy converter in rotary or pulsatile blood pumps that use electrical motors for pumping. However, in order to operate properly, the BLDCM driver needs to know the shaft position. Usually, that information is obtained through a set of Hall sensors assembled close to the rotor and connected to the electronic controller by wires. Sometimes, a large distance between the motor and controller makes the system susceptible to interference on the sensor signal because of winding current switching. Thus, the goal of the sensorless technique presented in this study is to avoid this problem. First, the operation of BLDCM was evaluated on the electronic simulator PSpice. Then, a BEMF detector circuitry was assembled in our laboratories. For the tests, a sensor-dependent system was assembled where the direct comparison between the Hall sensors signals and the detected signals was performed. The obtained results showed that the output sensorless detector signals are very similar to the Hall signals at speeds of more than 2500 rpm. Therefore, the sensorless technique is recommended as a responsible or redundant system to be used in rotary blood pumps.

Design optimization of cruciform specimens for biaxial fatigue loading

In order to correctly assess the biaxial fatigue material properties one must experimentally test different load conditions and stress levels. With the rise of new in-plane biaxial fatigue testing machines, using smaller and more efficient electrical motors, instead of the conventional hydraulic machines, it is necessary to reduce the specimen size and to ensure that the specimen geometry is appropriated for the load capacity installed. At the present time there are no standard specimen’s geometries and the indications on literature how to design an efficient test specimen are insufficient. The main goal of this paper is to present the methodology on how to obtain an optimal cruciform specimen geometry, with thickness reduction in the gauge area, appropriated for fatigue crack initiation, as a function of the base material sheet thickness used to build the specimen. The geometry is optimized for maximum stress using several parameters, ensuring that in the gauge area the stress is uniform and maximum with two limit phase shift loading conditions. Therefore the fatigue damage will always initiate on the center of the specimen, avoiding failure outside this region. Using the Renard Series of preferred numbers for the base material sheet thickness as a reference, the reaming geometry parameters are optimized using a derivative-free methodology, called direct multi search (DMS) method. The final optimal geometry as a function of the base material sheet thickness is proposed, as a guide line for cruciform specimens design, and as a possible contribution for a future standard on in-plane biaxial fatigue tests. © 2014, Gruppo Italiano Frattura. All rights reserved.

Fractional order electromagnetics

The Maxwell equations constitute a formalism for the development of models describing electromagnetic phenomena. The four Maxwell laws have been adopted successfully in many applications and involve only the integer order differential calculus. Recently, a closer look for the cases of transmission lines, electrical motors and transformers, that reveal the so-called skin effect, motivated a new perspective towards the replacement of classical models by fractional-order mathematical descriptions. Bearing these facts in mind this paper addresses the concept of static fractional electric potential. The fractional potential was suggested some years ago. However, the idea was not fully explored and practical methods of implementation were not proposed. In this line of thought, this paper develops a new approximation algorithm for establishing the fractional order electrical potential and analyzes its characteristics.

Optimization of cruciform specimens for biaxial fatigue loading with direct multi search

In order to correctly assess the biaxial fatigue material properties one must experimentally test different load conditions and stress levels. With the rise of new in-plane biaxial fatigue testing machines, using smaller and more efficient electrical motors, instead of the conventional hydraulic machines, it is necessary to reduce the specimen size and to ensure that the specimen geometry is appropriate for the load capacity installed. At the present time there are no standard specimen's geometries and the indications on literature how to design an efficient test specimen are insufficient. The main goal of this paper is to present the methodology on how to obtain an optimal cruciform specimen geometry, with thickness reduction in the gauge area, appropriate for fatigue crack initiation, as a function of the base material sheet thickness used to build the specimen. The geometry is optimized for maximum stress using several parameters, ensuring that in the gauge area the stress distributions on the loading directions are uniform and maximum with two limit phase shift loading conditions (delta = 0 degrees and (delta = 180 degrees). Therefore the fatigue damage will always initiate on the center of the specimen, avoiding failure outside this region. Using the Renard Series of preferred numbers for the base material sheet thickness as a reference, the reaming geometry parameters are optimized using a derivative-free methodology, called direct multi search (DMS) method. The final optimal geometry as a function of the base material sheet thickness is proposed, as a guide line for cruciform specimens design, and as a possible contribution for a future standard on in-plane biaxial fatigue tests

Aplicação de variadores de velocidade em sistemas de climatização

Por um lado vivemos numa sociedade cujos padrões de conforto são cada vez mais exigentes, por outro encontramo-nos numa era pautada por um certo declínio económico, social e também ambiental. Não se assumindo uma estratégia que limite ou diminua essas condições de conforto resta-nos atuar de forma a que os recursos utilizados para garantir esse mesmo conforto sejam utilizados da melhor forma possível. O setor dos edifícios é responsável por uma grande parcela de consumo de energia na sociedade atual, sendo que os sistemas de climatização que dele fazem parte, apresentam.se na maioria dos casos como os grandes consumidores de energia. Nesse sentido têm sido feitos esforços enormes no sentido de encontrar soluções que garantam a eficiência energética destes sistemas. O Variador Eletrónico de Velocidade apresenta-se como uma das soluções amplamente difundidas, na vertente do controle de processos e economia de energia. A sua aplicação em sistema de climatização é mais um desses casos. Nesse sentido, numa primeira parte é feito o estudo das características e funcionamento dos Variadores de Velocidade, Sistemas de Climatização e sua aplicação conjunta. Em seguida é realizada uma aplicação informática que pretende demonstrar a economia de energia garantida por aplicação de um Variador de Velocidade.

Software de gestão de manutenção como ferramenta de apoio à melhoria da eficiência da gestão de infraestruturas

Este trabalho académico surge no âmbito da realização da dissertação do Mestrado em Engenharia e Gestão Industrial. Tem como objetivo a melhoria da gestão do Departamento de Infraestruturas, numa empresa de produção de motores elétricos para a indústria automóvel, através da análise, implementação e melhoria de um software de gestão de manutenção, de forma a aumentar a eficiência do Departamento. Este estudo foi desenvolvido durante um estágio curricular na empresa Globe Motors Portugal Lda, localizada em Vila do Conde. Para sua sustentação, foi efetuada uma análise funcional, suportada por um Software de gestão de manutenção, de forma a perceber qual a importância que o mesmo tem no funcionamento do Departamento de Infraestruturas. Pretendeu-se compreender quais as vantagens e desvantagens da sua utilização. Posteriormente, implementou-se uma nova versão deste software, analisando-se os pontos fortes e as oportunidades de melhoria, de forma a tornar o Departamento de infraestruturas mais eficiente, através da utilização desta renovada ferramenta de trabalho. Como objetivo último, pretendeu-se à melhoria da organização e gestão do Departamento de infraestruturas, contribuindo para um desenvolvimento de toda a empresa, uma vez que comungamos a ideia de que só é possível ser competitivo, num mercado altamente exigente, através de processos eficientes, possibilitando a redução de custos a todos os níveis.

Sähkölaitekaapelipäätteiden kokoonpanotuotannon siirtäminen alihankkijalle

Työn tavoitteena oli selvittää kustannussäästöjä sähkölaitekomponentin kokoonpano- tuotannossa. Työssä vertaillaan oman ja alihankintatuotannon välisiä kustannuksia sekä tarkastellaan toiminnan joustavuutta, kun kokoonpano muodostuu kokonaisuudessaan ostettavista osista ja kuljetusmatka osien tuottajilta sekä myyjiltä on lyhyempi alihankkijalle, kuin omalle tehtaalle. Työssä järjestellään tuotteen kokoonpanolle edellytykset siirtymiseen alihankkijan hoidetta-vaksi niin, ettei siitä aiheudu ongelmia osavalmistuksen ja hankinnan, sekä valmiiden tuotteiden hallinnassa. Työssä selvitellään tuotteenmerkitystä ja sen kehittämistä sähkölaiteteollisuudelle. Tuotteen ja tuotannon kehittämisestä oli kohdeyrityksessä perustettu erityinen projekti, johon kuului myös muita sähkökaapeliliitäntään kuuluvia osia. Tuoteryhmä,jota tämä tutkimus käsittelee, siirrettiin alihankkijan kokoonpanotuotantoon vuonna 2000. Kaapelipäätteet kuuluvat yhtenä vaihtoehtoisena osana sähkölaitteiden voimakaape- loinnin läpivientiin ja suojaukseen. Projektissa kehitettiin 3 erilaista kaapelipäättä, joiden tehtävänä oli korvata 20 aikaisempaa mallia. Tällä tavoin kyseisen tuotteen ja sen komponenttien valmistussarjakokoja voitiin nostaa ja silti tuotannonkiertoa nopeuttaa, koska puskurivarastossa olevien variaatioiden määrä väheni 20:sta 3:een. Myös osa kokoonpanossa käytettävistä komponenteista voitiin käyttää kaikkien kaapelipäätemallien kokoonpanossa. Työssä vertaillaan kuljetuskustannusten eroa osahankinnassa oman ja alihankinta- tuotannon välillä, sekä vertaillaan varaston ja tuotannon tilankäyttöä ja tuotantokapasiteettia. Työn tarkoituksena on perustella ajatusta, että kuljetusmatkoja lyhentämällä voitaisiin saada kustannussäästöjä. Oman ja alihankintatyön kustannuksia vertaillaan ja huomattava säästö kokoonpanotyössä on tässä tapauksessa se, että alihankkijan laskutushinta työlle on alhaisempi, kuin mitä työn osuudelle on määritelty omassa tuotannossa. Varastotilan osalta vertailuatehtiin ainoastaan tilan käytön suhteen.

On the Analysis and Control of a Linear Synchronous Servomotor with a Flexible Load

Industry's growing need for higher productivity is placing new demands on mechanisms connected with electrical motors, because these can easily lead to vibration problems due to fast dynamics. Furthermore, the nonlinear effects caused by a motor frequently reduce servo stability, which diminishes the controller's ability to predict and maintain speed. Hence, the flexibility of a mechanism and its control has become an important area of research. The basic approach in control system engineering is to assume that the mechanism connected to a motor is rigid, so that vibrations in the tool mechanism, reel, gripper or any apparatus connected to the motor are not taken into account. This might reduce the ability of the machine system to carry out its assignment and shorten the lifetime of the equipment. Nonetheless, it is usually more important to know how the mechanism, or in other words the load on the motor, behaves. A nonlinear load control method for a permanent magnet linear synchronous motor is developed and implemented in the thesis. The purpose of the controller is to track a flexible load to the desired velocity reference as fast as possible and without awkward oscillations. The control method is based on an adaptive backstepping algorithm with its stability ensured by the Lyapunov stability theorem. As a reference controller for the backstepping method, a hybrid neural controller is introduced in which the linear motor itself is controlled by a conventional PI velocity controller and the vibration of the associated flexible mechanism is suppressed from an outer control loop using a compensation signal from a multilayer perceptron network. To avoid the local minimum problem entailed in neural networks, the initial weights are searched for offline by means of a differential evolution algorithm. The states of a mechanical system for controllers are estimated using the Kalman filter. The theoretical results obtained from the control design are validated with the lumped mass model for a mechanism. Generalization of the mechanism allows the methods derived here to be widely implemented in machine automation. The control algorithms are first designed in a specially introduced nonlinear simulation model and then implemented in the physical linear motor using a DSP (Digital Signal Processor) application. The measurements prove that both controllers are capable of suppressing vibration, but that the backstepping method is superior to others due to its accuracy of response and stability properties.

Taajuusmuuttajaohjatun pumppukäytön simulointimallin kehittäminen ja testaus

Pumppukäytöt vastaavat noin neljänneksestä Euroopan sähkömoottoreissa kulutettavasta sähkötehosta. Energian kallistumisen vuoksi energian säästämisestä ja energiatehokkuudesta on tullut yhä tärkeämpää. Taajuusmuuttajat ovat tuoneet yksinkertaisen säätötavan, jolla suurimmassa osassa pumppukäyttöjä voidaan saada huomattavia energiasäästöjä. Koko energiansäästöpotentiaalin hyödyntämiseksi täytyy kuitenkin pumppujen toimintaa tarkkailla. Tarkkailu voidaan toteuttaa käyttämällä taajuusmuuttajan sisäisiä mittauksia pumpun toimintapisteen määrittämiseen. Tässä työssä muodostetaan kaksi simulointimallia, joilla voidaan tutkia pumppukäytön toimintapistettä ja energiatehokkuutta. Pumpattavan nesteen ominaisuuksien vaikutusta malleihin tutkitaan ja tapoja korjata virhettä selvitetään. Mallien tuottamia estimaatteja verrataan laboratorio ja pilot-kohteiden mittauksiin. Pilot-kohteiden avulla tutkitaan voidaanko simulointimalleja käyttää teollisuuden energiansäästöpotentiaalia omaavien pumppukäyttöjen havaitsemiseen.

Ecodesign-direktiivi ja sen vaikutukset Suomessa

Direktiivi 2005/32/EY energiaa käyttävien tuotteiden ekologiselle suunnittelulle asetettavien vaatimusten puitteista annettiin 6.7.2005. Direktiivin puitteissa Euroopan komissio tulee antamaan tuoteryhmäkohtaisia asetuksia, joissa määritellään tuoteryhmäkohtaisesti ympäristövaatimukset. Direktiivin tarkoituksena on integroida ymparistönakokohdat ja elinkaariajattelu tuotesuunnitteluvaiheessa. Tällä direktiivillä pyritään parantamaan ympäristösuojelun tasoa ja tuotteiden energiatehokkuutta. Tämän diplomityön tarkoituksena on esitellä Ecodesign direktiiviä ja selvittää sen puitteissa annettujen asetusten vaikutusta Suomessa. Työssä tutkitaan hehkulamppujen maahantuonnin kieltävän asetuksen vaikutuksia kotitalouksiin, ympäristöön ja sähkömarkkinoihin. Lisaksi työssä on tutkittu sähkömoottoreita koskevan asetuksen vaikutuksia Suomen teollisuudessa. Lopuksi työssä arvioidaan Suomen ilmasto ja energiapolitiikan tavoitteiden ja velvoitteiden tuomien toimenpiteiden vaikutuksia. Työssä esitetään esimerkkitarkasteluja siitä, millaisia saastoja sähkönkulutukseen voitaisiin saavuttaa eri tuoteryhmissä direktiivin pohjalta annetuilla asetuksilla. Tarkasteluun valitut tuoteryhmät olivat kotitalouksien valaistus ja sähkömoottorit.

Pumppukäyttöjen energiankulutuksen määrittäminen prosessimittauksia käyttäen

Pumppukäytöt vastaavat noin neljännestä Euroopan alueen sähkömoottoreissa kuluvasta energiasta. Energian hinnan nousun vuoksi energian säästäminen ja energiatehokkuus ovat nousseet tärkeään asemaan paljon energiaa kuluttavassa teollisuudessa. Pumppukäyttöjen hyötysuhteen parantaminen on noussut olennaiseen osaan paperi- ja kartonkiteollisuuden energiatehokkuustarkasteluissa. Tässä työssä tarkastellaan kartonkikoneen pumppukäyttöjen toiminnan energiatehokkuutta moottorin virtamittausten perusteella. Analyysi perustuu moottorin akselitehon määrittämiseen ja sen perusteella tehtävään pumpun toimintapisteen laskentaan. Työssä esitellään käytetyt estimointimenetelmät ja niillä saadut tulokset kartonkikoneen pumppukäytöille. Lisäksi työssä arvioidaan kolmen yksittäisen pumppukäytön energiankulutuksen säästöpotentiaalia. Työssä käytettyä menetelmää voidaan käyttää sekä vakio- että vaihtonopeuspumppukäyttöjen toiminnan ja hyötysuhteen analysointiin.

Energy and Dynamics of the solar agricultural robot "SolarSprayer"

The main objective of the present study was to design an agricultural robot, which work is based on the generation of the electricity by the solar panel. To achieve the proper operation of the robot according to the assumed working cycle the detailed design of the main equipment was made. By analysing the possible areas of implementation together with developments, the economic forecast was held. As a result a decision about possibility of such device working in agricultural sector was made and the probable topics of the further study were found out.