963 resultados para Diodes, Schottky-barrier


Relevância:

100.00% 100.00%

Publicador:

Resumo:

We give a theoretical interpretation of the noise properties of Schottky barrier diodes based on the role played by the long range Coulomb interaction. We show that at low bias Schottky diodes display shot noise because the presence of the depletion layer makes the effects of the Coulomb interaction negligible on the current fluctuations. When the device passes from barrier to flat band conditions, the Coulomb interaction becomes active, thus introducing correlation between different current fluctuations. Therefore, the crossover between shot and thermal noise represents the suppression due to long range Coulomb interaction of the otherwise full shot noise. Similar ideas can be used to interpret the noise properties of other semiconductor devices.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

An analytical theory to describe the combined effects of the epitaxial layer thickness and the ohmic contact on the noise properties of Schottky barrier diodes is presented. The theory, which provides information on both the local and the global noise properties, takes into account the finite size of the epitaxial layer and the effects of the back ohmic contact, and applies to the whole range of applied bias. It is shown that by scaling down the epitaxial layer thickness, the current regime in which the noise temperature displays a shot-noise-like behavior increases at the cost of reducing the current range in which the thermal-noise-like behavior dominates. This improvement in noise temperature is limited by the effects of the ohmic contact, which appear for large currents. The theory is formulated on general trends, allowing its application to the noise analysis of other semiconductor devices operating under strongly inhomogeneous distributions of the electric field and charge concentrations.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

An analytical theory to describe the combined effects of the epitaxial layer thickness and the ohmic contact on the noise properties of Schottky barrier diodes is presented. The theory, which provides information on both the local and the global noise properties, takes into account the finite size of the epitaxial layer and the effects of the back ohmic contact, and applies to the whole range of applied bias. It is shown that by scaling down the epitaxial layer thickness, the current regime in which the noise temperature displays a shot-noise-like behavior increases at the cost of reducing the current range in which the thermal-noise-like behavior dominates. This improvement in noise temperature is limited by the effects of the ohmic contact, which appear for large currents. The theory is formulated on general trends, allowing its application to the noise analysis of other semiconductor devices operating under strongly inhomogeneous distributions of the electric field and charge concentrations.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Deep Level Transient Spectroscopy (DLTS) has been used to investigate hole traps in the depletion region of Schottky barrier diodes formed from electropolymerised poly(3-methylthiophene). The capacitance transients appear to be composed of a fast and a slow component. Analysis of the slower component using the ''rate window'' technique yields isochronal differential capacitance curves that depend on temperature in the manner predicted by theory.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Schottky-barrier devices were formed from electropolymerised films of poly (3-methylthiophene) (PMeT). Thermal annealing of a partially undoped film led to diodes with rectification ratios as high as 5900 at 1 V and 50,000 at 2.5 V and ideality factors slightly above 2. The temperature dependence of ac loss tangent and forward currents are identical suggesting that bulk effects dominate device behaviour event at very low forward voltages. Below 250 K forward currents are essentially independent of temperature. Preliminary TSC measurements show the presence of at least two trapping levels in the devices. © 1993.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The photocurrent action spectrum of a Schottky diode formed from electrodeposited poly(3-methylthiophene) is shown to follow closely the UV-visible absorption spectrum. At low forward bias, the peak photocurrent asymptotes to the expected square-root dependence on total potential, V-t, across the depletion region. At high reverse bias the superlinear dependence of the photocurrent on V-t suggests that internal photoemission from the rectifying aluminium electrode may be the dominant process.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Schottky barrier diodes based on Al/poly(3-methylthiophene)/Au have been fabricated and their electrical behaviour investigated. I-V characteristics revealed a dependence on the fabrication conditions, specifically on the time under vacuum prior to evaporation of the rectifying contact and post-metal annealing at elevated temperature. The available evidence is consistent with the formation of a thin insulating layer between the metal and the polymer following these procedures. Long periods under vacuum prior to deposition of the aluminium electrode reduced the likelihood of such a layer forming. Capacitance-voltage plots of the devices were stable to voltage cycling, so long as the forward voltage did not exceed similar to 1 V. Above this a small degree of hysteresis was observed, which is attributed to the filling/emptying of interface states or traps in the polymer.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Deep Level Transient Spectroscopy (DLTS) has been used to investigate hole traps in the depletion region of Schottky barrier diodes formed from electropolymerised poly(3-methylthiophene). The capacitance transients appear to be composed of a fast and a slow component. Analysis of the slower component using the ''rate window'' technique yields isochronal differential capacitance curves that depend on temperature in the manner predicted by theory.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Schottky-barrier devices were formed from electropolymerised films of poly (3-methylthiophene) (PMeT). Thermal annealing of a partially undoped film led to diodes with rectification ratios as high as 5900 at 1 V and 50,000 at 2.5 V and ideality factors slightly above 2. The temperature dependence of ac loss tangent and forward currents are identical suggesting that bulk effects dominate device behaviour event at very low forward voltages. Below 250 K forward currents are essentially independent of temperature. Preliminary TSC measurements show the presence of at least two trapping levels in the devices. © 1993.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The photocurrent action spectrum of a Schottky diode formed from electrodeposited poly(3-methylthiophene) is shown to follow closely the UV-visible absorption spectrum. At low forward bias, the peak photocurrent asymptotes to the expected square-root dependence on total potential, V-t, across the depletion region. At high reverse bias the superlinear dependence of the photocurrent on V-t suggests that internal photoemission from the rectifying aluminium electrode may be the dominant process.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Schottky barrier diodes based on Al/poly(3-methylthiophene)/Au have been fabricated and their electrical behaviour investigated. I-V characteristics revealed a dependence on the fabrication conditions, specifically on the time under vacuum prior to evaporation of the rectifying contact and post-metal annealing at elevated temperature. The available evidence is consistent with the formation of a thin insulating layer between the metal and the polymer following these procedures. Long periods under vacuum prior to deposition of the aluminium electrode reduced the likelihood of such a layer forming. Capacitance-voltage plots of the devices were stable to voltage cycling, so long as the forward voltage did not exceed similar to 1 V. Above this a small degree of hysteresis was observed, which is attributed to the filling/emptying of interface states or traps in the polymer.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The metal-insulator or metal-amorphous semiconductor blocking contact is still not well understood. Here, we discuss the steady state characteristics of a non-intimate metal-insulator Schottky barrier. We consider an exponential distribution (in energy) of impurity states in addition to impurity states at a single energy level within the depletion region. We present analytical expressions for the electrical potential, field, thickness of depletion region, capacitance, and charge accumulated in the depletion region. We also discuss ln I versus V(ap) data. Finally, we compare the characteristics in three cases: (i) impurity states at only a single energy level; (ii) uniform energy distribution of impurity states; and (iii) exponential energy distribution of impurity states.In general, the electrical characteristics of Schottky barriers and metal-insulator-metal structures with Schottky barriers depend strongly on the energy distribution of impurity states.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The metal-insulator or metal-amorphous semiconductor blocking contact is still not well understood. Here, the intimate metal-insulator and metal-oxide-insulator contact are discussed. Further, the steady-state characteristics of metal-oxide-insulator-metal structures are also discussed. Oxide is an insulator with wider energy band gap (about 50 Å thick). A uniform energetic distribution of impurities is considered in addition to impurities at a single energy level inside the surface charge region at the oxide-insulator interface. Analytical expressions are presented for electrical potential, field, thickness of the depletion region, capacitance, and charge accumulated in the surface charge region. The electrical characteristics are compared with reference to relative densities of two types of impurities. ln I is proportional to the square root of applied potential if energetically distributed impurities are relatively important. However, distribution of the electrical potential is quite complicated. In general energetically distributed impurities can considerably change the electrical characteristics of these structures.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

In this work we quantitatively map interface states in energy in a Schottky barrier between aluminum and the vacuum sublimed organic semiconductor terrylene. The density map of these interface states was extracted from the, admittance spectroscopy data. They revealed an interface state density of 2 x 10(12). cm(-2)eV(-1) close to the valence band which decreases slightly towards midgap. Additional do measurements show that the semiconductor bulk activation energy is 0.33 eV which may correspond to an acceptor level. (C) 2002 Elsevier Science B.V. All rights reserved.