Photonic switch and NOT logic gate based on the hybrid integration of a GaAsVCSEL and a GaAs MISS

The hybrid integrated photonic switch and not logic gate based on the integration of a GaAs VCSEL (Vertical Cavity Surface Emitting Lasers) and a MISS (Metal-Insulator-Semiconductor Switches) device are reported. The GaAs VCSEL is fabricated by selective etching and selective oxidation. The Ultra-Thin semi-Insulating layer (UTI) of the GaAs MISS is formed by using oxidation of A1As that is grown by MBE. The accurate control of UTI and the processing compatibility between VCSEL and MISS are solved by this procedure. Ifa VCSEL is connected in series with a MISS, the integrated device can be used as a photonic switch, or a light amplifier. A low switching power (10 mu W) and a good on-off ratio (17 dB contrast) have been achieved. If they are connected in parallel, they perform a photonic NOT gate operation.

Influence of lateral propagating modes on laser output characteristics in selectively oxidized vertical cavity surface-emitting lasers with double oxide layers

The influence of lateral propagating modes on the threshold current and the spontaneous emission factor in selectively oxidized vertical cavity surface-emitting lasers (VCSELs) is investigated based on the mode behaviors of lateral propagating modes and the rate equation model. The numerical results show that the lateral propagating modes may be trapped in the aperture region for the selectively oxidized VCSEL with two oxide layers, one above and one below the active region. The output characteristics of VCSELs can be affected due to the reabsorption of the quasitrapped lateral propagating modes. A lower threshold current can be expected for a VCSEL with double oxide layers than that with a single oxide layer. The numerical results of rate equations also show that a larger spontaneous emission factor can be obtained by fitting the output-input curves for the VCSEL with double oxide layers. (C) 1999 American Institute of Physics. [S0021-8979(99)07919-0].

Stability improvement of selective oxidation during the fabrication of InGaAs/GaAs vertical cavity surface emitting laser

The effects of the carrier gas flow and water temperature on the oxidation rate for different reaction temperatures were investigated. The optimum conditions for stable oxidation were obtained. Two mechanisms of the oxidation process are revealed. One is the flow-controlling process, which is unstable. The other is the temperature-controlling process, which is stable. The stable region decreases for higher reaction temperatures. The simulation results for the stable oxidation region are also given. With optimum oxidation conditions, the stability and precision of the oxidation can be dramatically improved.

甚短距离光传输技术

本书从光电子器件及其在光通信领域的应用出发，介绍了甚短距离光传输技术的组成、原理、实现方案、技术性能、关键技术以及在高速互连领域内的应用等。本书重点阐述了垂直腔面发射激光器的原理、工艺和特性；10gb/s和40gb/s传输方案的具体实现及其性能指标；甚短距离光传输涉及到的各项关键技术，如新型多模光纤技术、cwdm复用技术、硅探测器技术、高速光电集成(oeic)技术以及相关高速网络技术等。

微电子与光电子集成技术

微电子技术与光电子技术紧密结合，相互渗透，必将推进信息技术及相关的高新技术进入新的发展阶段。本书共分为9章，从技术基础和实际应用的角度出发，着重对微电子与光电子集成技术相关的工艺基础、基本原理和关键集成技术进行了详细阐述，主要内容包括光发射器件、光电探测器、光波导器件、光电子专用集成电路、硅基光电子集成回路、甚短距离光传输技术以及微电子与光电子混合集成技术等。 微电子与光电子集成技术的实用化进程，必将为21世纪科学技术的发展作出重大贡献。然而，微电子与光电子集成技术是信息技术发展的一个崭新方向，虽然各项关键技术的发展取得了一定的进步，但还存在诸多难题需要进一步解决和完善。 本书主要为从事集成光电子和光通信等相关技术研究的科研人员提供参考。

Fabrication and characterization of TO packaged high-speed laser modules - art. no. 682407

Various high-speed laser modules are fabricated by TO-Packaged processes, such as FP laser modules, DFB laser modules, and VCSEL modules. Furthermore,, the resonance among the circuit elements provides an approach to compensating the TO packaging parasitics, and improving the frequency response of the devices. The detailed equivalent circuit model is established to investigate both the laser diode and packaging comprehensively. The small-signal modulation bandwidths of the TO packaged FP laser, DFB laser and the VCSEL modules are more than 10, 9.7 and 8 GHz, respectively.

The application of parallel optical transmitter and receiver modules in communication subsystems

A new 12 channels parallel optical transmitter module in which a Vertical Cavity Surface Emitting Laser (VCSEL) has been selected as the optical source is capable of transmitting 37.5Gbps date over hundreds meters. A new 12 channels parallel optical receiver module in which a GaAs PIN (p-intrinsic-n-type) array has been selected as the optical receiver unit is capable of responding to 30Gbps date. A transmission system based on a 12 channels parallel optical transmitter module and a 12 channels parallel optical receiver module can be used as a 10Gbps STM-64 or an OC-192 optical transponder. The parallel optical modules and the parallel optical transmission system have passed the test in laboratory.

An analysis and simulation about conditioned launch for very short reach (VSR-4)

VSR4 links use graded index multimode fibers (GIMMFs) as the transmission medium with operation wavelength 850nm. For cost reasons, VCSEL has been selected as the optical source to VSR4. The minimum bandwidth specification for 62.5um GIMMF in VSR4 is only 400 MHz(.)km for over-filled-launch (OFL) condition. The distance of 300 meters is limited over transmission rates of 1.25Gbit/s on the basis of this specification. In order to overcome the OFL bandwidth limit by selective excitation of a limited number of modes, conditioned launch technique is investigated. In this paper, based on a comprehensive dispersion theory of GIMMF, a model is built to simulate the transmission of optical signal in GIMMFs and a comparison between OFL and conditioned launch is analyzed. The result can be the guidelines for the best choice of techniques for various LAN and interconnect systems also.

Proposed scheme for parallel 10Gb/s VSR system and its Verilog HDL realization

This paper proposes a novel and innovative scheme for 10Gb/s parallel Very Short Reach (VSR) optical communication system. The optimized scheme properly manages the SDH/SONET redundant bytes and adjusts the position of error detecting bytes and error correction bytes. Compared with the OIF-VSR4-01.0 proposal, the scheme has a coding process module. The SDH/SONET frames in transmission direction are disposed as follows: (1) The Framer-Serdes Interface (FSI) gets 16x622.08Mb/s STM-64 frame. (2) The STM-64 frame is byte-wise stripped across 12 channels, all channels are data channels. During this process, the parity bytes and CRC bytes are generated in the similar way as OIF-VSR4-01.0 and stored in the code process module. (3) The code process module will regularly convey the additional parity bytes and CRC bytes to all 12 data channels. (4) After the 8B/10B coding, the 12 channels is transmitted to the parallel VCSEL array. The receive process approximately in reverse order of transmission process. By applying this scheme to 10Gb/s VSR system, the frame size in VSR system is reduced from 15552x12 bytes to 14040x12 bytes, the system redundancy is reduced obviously.

A novel photonic crystal vertical cavity surface emitting laser based on coherent coupling

We demonstrate a novel oxide confined GaAs-based photonic crystal vertical cavity surface emitting laser (PC-VCSEL) operating at a wavelength of 850 nm based on coherent coupling. A ring-shaped light-emitting aperture is added to the conventional PC-VCSEL, and coherent coupling is achieved between the central defect aperture and the ring-shaped light-emitting aperture. Measurements show that under the continuous-wave (CW) injected current of 20 mA, a high power of 2 mW is obtained, and the side mode suppression ratio (SMSR) is larger than 20 dB. The average divergence angle is 4.2 degrees at the current level of 20 mA. Compared with the results ever reported, the divergence angle is reduced.

Control of the photonic crystal waveguide over the beam profile of vertical-cavity surface-emitting lasers

The control of the photonic crystal waveguide over the beam profile of vertical-cavity surface-emitting lasers is investigated. The symmetric slab waveguide model is adopted to analyze the control parameters, of the beam profile in the photonic-crystal vertical-cavity surface-emitting laser (PC-VCSEL). The filling factor (the ratio of the hole diameter to the lattice constant) and the etching depth control the divergence angle of the PC-VCSEL, and the low filling factor and the shallow etching depth are beneficial to achieve the low-divergence-angle beam. Two types of PC-VCSELs with different filling factors and etching depths are designed and fabricated. The experimental results show that the device with a lower filling factor and a shallower etching depth has a lower divergence angle, which agrees well with the theoretical predictions.

Phase-locked ring-defect photonic crystal vertical-cavity surface-emitting laser

Phase-locked oxide-confined ring-defect photonic crystal vertical-cavity surface-emitting laser is presented. The coupled-mode theory is employed to illustrate the two supermodes of the device, in-phase and out-of-phase supermode. Experimental results verify the two supermodes by the characteristics of the spectra and the far field patterns. At the lower current, only the out-of-phase supermode is excited, whereas under the higher current, the in-phase supermode also appears at the shorter wavelength range. In addition, the measured spectral separation between the two supermodes agrees well with the theoretical result.

GaN基垂直腔面发射激光器的研制

作者在我国大陆首次实现了GaN基垂直腔面发射激光器（VCSEL）的激射．首先采用金属有机物化学气相沉积（MOCVD）技术在蓝宝石衬底上进行高质量氮化物增益区的外延生长．然后在表面沉积高反射介质膜分布布拉格反射镜（DBR）．将样品键合到其它支撑片上后，采用激光剥离技术将蓝宝石衬底去除．再在去除蓝宝石后露出的氮化物表面沉积第二组介质膜DBR制成VCSEL．在室温光泵条件下，观察到VCSEL的激射．激射波长449．5nm。阈值6．5mJ／cm~2．激射峰的半高宽小于0．1nm，这些指标达到了国际领先水平．本文为进一步研制实用化氮化物VCSEL奠定了重要的基础．

基于STM-64的甚短距离并行光传输系统

研究了STM-64数据帧的转换映射技术,利用垂直腔面发射激光器(VCSEL)列阵光源和PIN列阵探测器成功研制出10 Gb/s的甚短距离12信道SDH并行光传输系统,该系统结构紧凑,具有检错和纠错功能。跟传统的10 Gb/s串行光传输系统相比,本系统降低了对单路器件传输性能的要求。经SDH传输测试仪测试,系统能实现无误传输。

键合界面对面发射激光器光与热性质的影响

通过界面有效吸收系数的计算及界面对腔模的反射率的影响可知,采用双面键合技术制备面发射激光器应使键合界面处于驻波场分布零点位置,同时界面厚度应该小于20nm以使器件光学性能受界面吸收系数的影响较小.采用有限元方法分析VCSEL温度分布,结果证实薄的键合界面使VCSEL有源区温度对界面的热导率和电导率改变不敏感,而厚的键合界面将可能使有源区温度有较大地升高,给器件带来严重的不良影响.亲水键合和疏水键合的SEM照片说明疏水处理界面较薄,适合用于器件的制备.而亲水处理界面厚度〉40nm,对器件的光、热特性不利.