Concentração do óleo de girassol em compostos insaturados utilizando destilação molecular

Vegetable oils are characterized as important raw materials in the supplying of natural substances of interest pharmaceutical, food and cosmetic industry. Sunflower oil stands out for its important composition present in unsaturated fatty acids such as oleic acid (C18:1) and linoleic (C18:2), responsible for many health benefits. The main objective of this study is obtain enriched fractions in unsaturated compounds from refined sunflower oil. The oil used in this study was characterized by the determination of some properties, like iodine number, acid number and viscosity. A transesterification was done to transform the triglycerides into their corresponding methyl esters of fatty acids. These was submitted the molecular distillation process, for present as an efficient alternative to separation and purification of these substances, using high vacuum and low temperatures. Of the esters fractions that was obtained, were analyzed by gas chromatography. The experimental design technique was used to evaluate the influence of the temperature variation of evaporation and condensation system on the percentage obtained residue. The evaporator temperature proved to be the most influential variable on the studied response. The optimized conditions for the answer was studied at 100 °C for evaporator temperature and 10 °C for the condenser temperature. The graph of "split ratio" showed that for the lowest flow feed (1 mL/min) and higher evaporator temperature (110 °C) was obtained in the largest fraction of distillate. It also used the study of the influence of evaporator temperature on the concentration of unsaturated compounds. The best operating conditions for temperature was 90 °C reached 82.21 % of unsaturated compounds. Elimination curves of the unsaturated compounds present in the distillate stream were obtained. The simulation results of the molecular distillation process of sunflower oil showed the concentration profiles for three different feed flow rates. The speed, temperature and thickness profiles of the liquid film were obtained. The speed of the film increases as the fluid flows through the walls of the evaporator, reaching a maximum on length of 0.075 m. The film thickness decreases on the route, since many compounds are volatilized. The result of the temperature profile had to be consistent with the literature reproduced, being constant after reaching the maximum operating temperature in the length of 0.15 m. This study allowed characterizing and focusing, through experimental analysis, unsaturated compounds and observing the sunflower oil´s behavior through process simulation.

Análise tribo-termodinâmica da aplicação de nanopartículas de Al2O3 como aditivo lubrificante em compressor hermético de refrigeração

The thermodynamic performance of a refrigeration system can be improved by reducing the compression work by a particular technique for a specific heat removal rate. This study examines the effect of small concentrations of Al2O3 (50 nm) nanoparticles dispersion in the mineral oil based lubricant on the: viscosity, thermal conductivity, and lubrication characteristics as well as the overall performance (based on the Second Law of Thermodynamics) of the refrigerating system using R134a or R600a as refrigerants. The study looked at the influences of variables: i) refrigerant charge (100, 110, 120 and 130 g), ii) rotational speed of the condenser blower (800 and 1100 RPM) and iii) nanoparticle concentration (0.1 and 0.5 g/l) on the system performance based on the Taguchi method in a matrix of L8 trials with the criterion "small irreversibility is better”. They were carried pulldown and cycling tests according to NBR 12866 and NBR 12869, respectively, to evaluate the operational parameters: on-time ratio, cycles per hour, suction and discharge pressures, oil sump temperature, evaporation and condensation temperatures, energy consumption at the set-point, total energy consumption and compressor power. In order to evaluate the nanolubricant characteristics, accelerated tests were performed in a HFRR bench. In each 60 minutes test with nanolubricants at a certain concentration (0, 0.1 and 0.5 g/l), with three replications, the sphere (diameter 6.00 ± 0.05 mm, Ra 0.05 ± 0.005 um, AISI 52100 steel, E = 210 GPa, HRC 62 ± 4) sliding on a flat plate (cast iron FC200, Ra <0.5 ± 0.005 um) in a reciprocating motion with amplitude of 1 mm, frequency 20 Hz and a normal load of 1,96 N. The friction coefficient signals were recorded by sensors coupled to the HFRR system. There was a trend commented bit in the literature: a nanolubricant viscosity reduction at the low nanoparticles concentrations. It was found the dominant trend in the literature: increased thermal conductivity with increasing nanoparticles mass fraction in the base fluid. Another fact observed is the significant thermal conductivity growth of nanolubricant with increasing temperature. The condenser fan rotational speed is the most influential parameter (46.192%) in the refrigerator performance, followed by R600a charge (38.606%). The Al2O3 nanoparticles concentration in the lubricant plays a minor influence on system performance, with 12.44%. The results of power consumption indicates that the nanoparticles addition in the lubricant (0.1 g/L), together with R600a, the refrigerator consumption is reduced of 22% with respect to R134a and POE lubricant. Only the Al2O3 nanoparticles addition in the lubricant results in a consumption reduction of about 5%.

Análise tribo-termodinâmica da aplicação de nanopartículas de Al2O3 como aditivo lubrificante em compressor hermético de refrigeração

The thermodynamic performance of a refrigeration system can be improved by reducing the compression work by a particular technique for a specific heat removal rate. This study examines the effect of small concentrations of Al2O3 (50 nm) nanoparticles dispersion in the mineral oil based lubricant on the: viscosity, thermal conductivity, and lubrication characteristics as well as the overall performance (based on the Second Law of Thermodynamics) of the refrigerating system using R134a or R600a as refrigerants. The study looked at the influences of variables: i) refrigerant charge (100, 110, 120 and 130 g), ii) rotational speed of the condenser blower (800 and 1100 RPM) and iii) nanoparticle concentration (0.1 and 0.5 g/l) on the system performance based on the Taguchi method in a matrix of L8 trials with the criterion "small irreversibility is better”. They were carried pulldown and cycling tests according to NBR 12866 and NBR 12869, respectively, to evaluate the operational parameters: on-time ratio, cycles per hour, suction and discharge pressures, oil sump temperature, evaporation and condensation temperatures, energy consumption at the set-point, total energy consumption and compressor power. In order to evaluate the nanolubricant characteristics, accelerated tests were performed in a HFRR bench. In each 60 minutes test with nanolubricants at a certain concentration (0, 0.1 and 0.5 g/l), with three replications, the sphere (diameter 6.00 ± 0.05 mm, Ra 0.05 ± 0.005 um, AISI 52100 steel, E = 210 GPa, HRC 62 ± 4) sliding on a flat plate (cast iron FC200, Ra <0.5 ± 0.005 um) in a reciprocating motion with amplitude of 1 mm, frequency 20 Hz and a normal load of 1,96 N. The friction coefficient signals were recorded by sensors coupled to the HFRR system. There was a trend commented bit in the literature: a nanolubricant viscosity reduction at the low nanoparticles concentrations. It was found the dominant trend in the literature: increased thermal conductivity with increasing nanoparticles mass fraction in the base fluid. Another fact observed is the significant thermal conductivity growth of nanolubricant with increasing temperature. The condenser fan rotational speed is the most influential parameter (46.192%) in the refrigerator performance, followed by R600a charge (38.606%). The Al2O3 nanoparticles concentration in the lubricant plays a minor influence on system performance, with 12.44%. The results of power consumption indicates that the nanoparticles addition in the lubricant (0.1 g/L), together with R600a, the refrigerator consumption is reduced of 22% with respect to R134a and POE lubricant. Only the Al2O3 nanoparticles addition in the lubricant results in a consumption reduction of about 5%.

Determinação voltamétrica de zinco empregando eletrodos quimicamente modificados com bismuto

This dissertation presents the development of voltammetric methods to zinc determination in multivitamin commercial samples, talc, and art materials for painting (soft pastel) combining an alkaline extraction with 1.0 mol L-1 NaOH aqueous solution and bismuth modified electrodes. Two electrodes were used to zinc quantification in the samples, bismuth film electrode (BiFE) plated in situ onto glassy carbon and carbon paste electrode chemically modified with strongly acidic ion exchange resin Amberlite® IR 120 and bismuth nanostructures (EPCAmbBi). It was verified that the best concentration of Bi3+ for Bi film deposition onto glassy carbon was 4.0 μmol L-1 using an 0.1 mol L-1 acetate buffer aqueous solution (pH = 4.5) as supporting electrolyte. The best condition to formation of Bi nanostructures in the EPC modified with 10 % Amberlite® IR 120 was the use of 30 s to pre-concentration (open circuit) in 0.5 mmol L-1 Bi3+ aqueous solution (pH 5.5) prepared with supporting electrolyte solution. The obtained analytical curve for Zn2+ using BiFE presented linear range from 0.5 to 5.0 μmol L-1, the limit of detection (LD) was 41 nmol L-1. For EPCAmbBi only one linear range was observed for the analytical curve varying the Zn2+ concentration from 0.05 to 8.2 μmol L-1, LD obtained in this curve it was equal to 10 nmol L-1. The EPCAmbBi presented the most intense and sharp anodic stripping peaks for Zn2+ presenting, therefore, a better voltammetric profile, with sensitivity higher than obtained with the BiFE. Moreover, the EPCAmbBi presented a LD lower than that obtained with the BiFE. Alkaline extraction was an efficient sample pretreatment to extract Zn2+ from solid samples, besides that, this procedure was less susceptible to interferences from Cu2+, since it remains at extracting vessel as insoluble Cu(OH)2. The combination of alkaline extraction with the EPCAmbBi is a simple, fast, efficient and low cost for the zinc determination in pharmaceutical formulations and art materials for painting (soft pastel) samples, which can be employed as a low-cost alternative method to the atomic absorption spectroscopy.

Avaliação das condições de precipitação do azul da Prússia sobre pó de grafite visando o desenvolvimento de eletrodos de pasta de carbono para a quantificação de nitrito

An amperometric FIA method for nitrite quantification based on nitrite electroreduction and employing a carbon paste electrode (CPE) chemically modified with iron hexacyanoferrate (HCF) as an amperometric detector was developed. The influence of experimental conditions on the preparation of the electrode materials was evaluated and the materials obtained in each study were used for the development of modified electrodes. The electrochemical sensors were prepared by a fast, simple, and inexpensive procedure, and the long-term performance of the electrodes were quite satisfactory as the stability was maintained over one year. HCF was an effective redox mediator for nitrite electroreduction in acidic media, allowing nitrite detection at +0.2 V vs. Ag/AgClsat, which is a potential free of possible interfering species that are normally present in food and water samples. The electrochemical cell used in the FIA system was similar to a batch injection analysis cell, enabling recirculation of the carrier solution. This is an attractive feature because it allows the use of a high flow rate (6 mL min-1) leading to high sensitivity and analysis speed, while keeping reagent consumption low. The proposed method had a detection limit of 9 μmol L-1 and was successfully employed for nitrite quantification in spiked water and sausage samples. The obtained results were in good agreement with those provided by the spectrophotometric official method. At a 95 % confidence level it was not observed statistical differences neither in nitrite content nor in the precision provided by both methods. The experimental conditions for the synthesis of HCF were optimized and the best electrode material was prepared by mixing FeCl3, K4[Fe(CN)6] and carbon powder subjected to an acid and thermal treatment (400 ºC), followed by ultrasonic agitation at 4 °C. This material was used to construct an electrode with improved analytical performance to reduce nitrite, which presented greater stability compared to HCF film electrodeposited on the EPC, showing that the preparation procedure of the electrode material is an effective strategy for the development of HCF modified electrodes.

Obtenção de triacetato de celulose a partir do bagaço de cana-deaçúcar para revestimento de micropartículas de goma gelana e avaliação do seu perfil de liberação in vitro e da mucoadesão ex vivo

Oral route of administration is considered to be the most comfortable, safe and greater adaptation for patients. But, oral route presents some disadvantages such as drugs bioavailability and side effects on the stomach. Some technologies are studied to soften and/or resolve these problems, such as coating with polymeric films, which are able to protect the pharmaceutical form of the acid stomachic environment and to act in the drug release, and mucoadhesive systems, which allow the pharmaceutical form remains a greater time interval in the intestine, increasing the effectiveness of the drug. Cellulose triacetate (CTA) films were produced from cellulose extracted from sugar cane bagasse. The films were prepared with different morphologies (with and without water, acting as non-solvent) and concentrations (3, 6.5 and 10%) of CTA and characterized using scanning electron microscopy (SEM), water vapor permeability (WVP), puncture resistance (PR), enzymatic digestion (DE), and mucoadhesive force evaluation (MF). Microscopy showed the formation of symmetric and asymmetric morphologies. WVP data showed that more concentrated films have higher values for WVP; moreover, asymmetric films had higher values than symmetric films. PR measurements showed that symmetric membranes are more resistant than asymmetric ones. More concentrated films were also more puncture resistant, except for symmetric membranes with CTA concentrations of 6.5 and 10% that did not show significant differences. All of the films presented large mucoadhesive capacities independent of their morphology and CTA concentration. From the results of WVP and RP, a symmetric filme with 6.5% CTA showed better ability and mechanical resistance, therefore, was selected to serve as coating of gellan gum (GG) particles incorporating ketoprofen (KET), which was confirmed by SEM. The selected film presented low values in measurements of the swelling index (SI) and in a dissolution test (DT). TGA analysis showed that the CTA coating does not influence the thermal stability of the particles and there is no incompatibility evidence between CTA, GG and KET. Coated particles released 100% of the ketoprofen in 24 h, while uncoated particles released the same amount in 4 h. The results of this study highlight the potential of CTA in the development of new controlled oral delivery systems.

Winter lovers: engajamento e participação no universo de game of thrones da internet

The formation of groups acquired new features with the arrival of the internet. The links before straitened between family, work groups and close friends today reach long distances through online communities. These communities represent groups that have affinities and common interests, and use the community space to discuss these. Examples of these communities are those related to franchise Game of Thrones, a literary phenomenon that has expanded by various media, including the social, television, and communities. This report aims to present the work steps and the theoretical reflection, necessary for the achievement of a final product in file format, which aimed to measure the engagement and participation of GOT fans on the Internet, especially in two Facebook GOT communities during the fifth season of the series aired on HBO.

A MULHER ALÉM DO BEM E DO MAL: Malévola e a representação cinematográfica do feminino integrado

Estudo sobre as construções simbólicas e identitárias da mulher presentes na narrativa e na estrutura das personagens femininas do filme Malévola (2014) – produção dos estúdios Disney (EUA). A narrativa é inspirada no conto de fadas “A Bela Adormecida do Bosque” e distingue-se pela perspectiva feminina, modificando as possibilidades de interpretação, além de possibilitar a quebra do paradigma dicotômico relacionado ao Bem e ao Mal. A pesquisa tem por objetivo estudar a evolução das construções imaginárias da mulher no cinema e traçar paralelos entre as características arquetípicas das personagens de Malévola em relação à identidade da mulher na contemporaneidade. Para tal, será tomado como referencial teórico os estudos do imaginário social, com as obras de Gilbert Durand, Edgar Morin e, em especial, Michel Maffesoli; conceitos da psicanálise a partir dos trabalhos de C.G. Jung, Erich Neumann, Marie-Louise Von Franz e Clarissa Pinkola Estés; as teorias de Stuart Hall, Laura Mulvey e Gilles Lipovetsky relacionadas aos estudos culturais com ênfase em gênero; e também o ecofeminismo através dos trabalhos de autoras como Vandana Shiva e Maria Mies. Nosso referencial teórico-metodológico é a Hermenêutica de Profundidade (HP) visando à interpretação da estrutura simbólica de nosso objeto. Resultam desta pesquisa a verificação de um processo de saturação de padrões identitários e simbólicos provindos da modernidade e a evolução de novas dinâmicas nas narrativas presentes nas mídias e na comunicação.

Narrativas del multilateralismo: «efecto Rashomon» y cambio de poder

El multilateralismo eficaz se ha convertido en un lugar común del discurso político internacional. Pero el multilateralismo es un concepto y una práctica problemática, y no se concibe o interpreta de la misma manera por parte de diferentes actores. Si Estados Unidos continua impulsando un multilateralismo hegemónico, la UE promueve un multilateralismo normativo, los países en desarrollo practican un multilateralismo defensivo y los emergentes promueven un multilateralismo revisionista basados en narrativas, legitimaciones discursivas, objetivos y prácticas diferenciadas. El artículo trata de caracterizar cada una de esas visiones a partir de sus narrativas y lógicas discursivas; se utiliza cómo argumento el denominado «efecto Rashomon», basado en el filme homónimo de Akira Kurosawa, que muestra cómo pueden coexistir distintos relatos de un determinado hecho, y cómo estos configuran expectativas, roles y conductas de los actores implicados. Finalmente, se analiza en qué medida esas narrativas se ven desafiadas por los procesos de cambio de poder del sistema internacional y reclaman un marco común.

Víctor Erice en la Escuela Oficial de Cinematografía. Elogio de la incomunicación

Aunque Víctor Erice es uno de los directores españoles más estudiados del cine español, sus trabajos en el Instituto de Investigaciones y Experiencias Cinematográficas, que más tarde pasará a llamarse Escuela Oficial de Cinematografía, no se han analizado en profundidad. Salvo su práctica de tercer curso, Los días perdidos, el resto de los cortometrajes y los guiones escritos se han considerado obras menores, piezas sin importancia relevante o directamente títulos extraviados. Sin embargo, estos trabajos se encuentran en buen estado en el archivo de la Escuela Oficial de Cine custodiado por la Filmoteca Española. De Víctor Erice se conservan cuatro cortometrajes y cinco guiones cinematográficos para piezas breves. En este artículo, resumen de una investigación realizada sobre dicho material inédito, se quiere mostrar cómo estas obras presentan un valor en sí mismas y deben ser analizadas como parte importante de la filmografía de este autor. En todos estos trabajos, sin dejar de ser ejercicios de escuela, se muestra la mirada de un cineasta pleno. Así, existen elementos que serán clave en el posterior universo temático y estético de Víctor Erice. Además, el creador aborda como problemática central de sus prácticas el tema de la comunicación humana, o más propiamente el de la incomunicación. En los guiones y los cortometrajes cata­logados de la etapa en la EOC se observa cómo Erice, influenciado en parte por Michelangelo Antonioni, investiga estéticamente el modo de narrar y mostrar los procesos que conducen a la incomunicación y al aislamiento de sus protagonistas.

Colonialism, political unconscious and cognitive mapping in the space of the film "Captain Phillips"

The purpose of this article has been made through a Marxist analysis of the US film "Captain Phillips" (PaulGreengrass, 2013), based on a true story. I have found how the evolution of capitalism in the West continuesto consolidate the belief reified in a historical and geographical superiority of the political and socioeconomicwestern models regarding Africa and Asia lowers models. At the same time, through categories like dialecticalmaterialism, criticism of diffusionist theory and application of cognitive mapping to large geopoliticalspaces located in most poor areas of the world, I have realized a remark about currently being articulatingthe political unconscious of working class in rich countries and the poor in poor countries, establishing arelationship between the ideological representation that takes an individual from his historical reality (ona scale that moves from local to global), and how he has developed a mental ability to escape of the responsibilityto make a critical review of what's happening around him in all areas. Finally, through physicalspace captured in the film, I have realized a materialist critique of globalized business process that takesplace through the carriage of goods, outlining spatial and cognitively limits of the mentality of our time, bothamong "winners"as among the "losers", based on the spatial movement of capital.

Is the cinematic newsreel the strongest weapon? The "Luce" newsreel reception during fascism

The Luce newsreel was a fascist-pivotal propaganda instrument. Mussolini thought movies were the strongestweapon; however, the efficiency of cinematographic propaganda on people did not work as well as expected,especially nonfiction. This article intends to value, through oral testimonies, the influence of Lucenewsreel on the Italian population during fascism, the degree of truth of film news, and which of those piecesof news were more repeated, as well as the influence of the Italian and its leader image on the collective mind.

Between representation and figuration. Nouvelle Vague’s cinema: a history revision

50 years after the birth of the Nouvelle Vague, the inheritance that the contemporary cinema receives from it is inevitable. Figures and visual motifs; stories, themes, faces or common places; aesthetic and language devices. The echoes appear in various ways, each affiliation involves a different relationship and therefore a dissimilar approximation to its analysis. And yet, both the academy and the film critics maintain their will to think the Nouvelle Vague as a whole, a universe, a stream or an aesthetic trend. However, does a Nouvelle Vague’s aesthetic exist? And if so: why and how to address their historical revision? Taking Deleuze’s thesis on the time-image and Serge Daney’s assertion according to which 50 years after the birth of the Nouvelle Vague, the inheritance that the contemporary cinema receives from it is inevitable. Figures and visual motifs; stories, themes, faces or common places; aesthetic and language devices. The echoes appear in various ways, each affiliation involves a different relationship and therefore a dissimilar approximation to its analysis. And yet, both the academy and the film critics maintain their will to think the Nouvelle Vague as a whole, a universe, a stream or an aesthetic trend. However, does a Nouvelle Vague’s aesthetic exist? And if so: why and how to address their historical revision? Taking Deleuze’s thesis on the time-image and Serge Daney’s assertion according to which

DISSERTAÇÃO - Cinema na Educação: uma forma inovativa para compreender literatura brasileira no ensino médio

Dissertação apresentada ao Programa de Pós-Graduação em Comunicação da Universidade Municipal de São Caetano do Sul para a obtenção do título de Mestre em Comunicação.

Materiais à base de Sr(Ti,Nb)O3 para sensores lambda

Os sensores lambda resistivos possuem as vantagens de simplicidade e menor custo relativamente à utilização generalizada de sensores potenciométricos de oxigénio. Nesse sentido, os titanatos de estrôncio têm sido alvo de diversos estudos. Para a produção de uma relação inequívoca entre a condutividade destes materiais e a pressão parcial de oxigénio é necessária a adição de um dopante dador que suprime a condução eletrónica do tipo-p na região de pressões parciais de oxigénio próximas de ar. Contudo, a adição de um dopante dador produz respostas lentas destes materiais quando densos a variações da pressão parcial de oxigénio. Além da preparação usual dos pós por reação do estado sólido, foram preparadas diversas composições por mecanossíntese. Tal relaciona-se com o fato exaustivamente reportado de as amostras destes materiais, especialmente quando dopados com dadores, apresentarem comportamentos dependentes das condições de processamento. Teve ainda o intuito de avaliar a viabilidade da sua preparação por este método, e consequentemente verificar se este método de preparação, que presumivelmente produzirá pós com composição mais homogénea e mais reativos, permite alterar/manipular a resposta obtida por amostras com eles produzidas. Foram preparados diversos filmes, tipologia muito usada na produção de sensores resistivos, e amostras porosas com diversas composições à base de titanato de estrôncio produzidos com variadas condições de processamento. Foram realizadas diversas caracterizações sobre estes espécimes numa tentativa de melhor compreender as propriedades destes materiais e a dependência destas com parâmetros microestruturais como o tamanho de grão e a porosidade. Foi verificado que os exemplares de titanato de estrôncio não dopado, quer em filmes quer em amostras porosas, apresentam um comportamento elétrico semelhante ao apresentado por amostras densas deste material. Apurou-se ainda, que as suas características apresentam uma variação ténue com a alteração das condições de processamento. Já espécimes de titanato de estrôncio dopados com dador revelam uma forte dependência das suas propriedades com as condições de processamento utilizadas, nomeadamente, a temperatura de sinterização e o tempo de permanência a essa temperatura. Para o fabrico de sensores resistivos de oxigénio poderá ser preferível o recurso a amostras porosas pelo facto de mais facilmente se manipularem as suas características microestruturais e devido à exclusão dos problemas associados à interação entre o substrato de alumina e o filme. As composições não dopadas são as indicadas para esta função se a gama de pressões de oxigénio a avaliar for relativamente pouco extensa sendo aconselhadas as composições dopadas com dador se for pretendida uma medição da pressão parcial de oxigénio em zonas mais extensas correspondentes à queima com deficiência ou excesso de oxigénio. Mesmo em amostras de elevada porosidade poderá ocorrer resposta transiente do material dopado com dador.