Power Consumption in Carbon Capture and Storage Systems (CCS) and Possibilities to Reduce Power Consumption with Variable Speed Drives

The aim of this master´s thesis is to study which processes increase the auxiliary power consumption in carbon capture and storage processes and if it is possible to reduce the auxiliary power consumption with variable speed drives. Also the cost of carbon capture and storage is studied. Data about auxiliary power consumption in carbon capture is gathered from various studies and estimates made by various research centres. Based on these studies a view is presented how the power auxiliary power consumption is divided between different processes in carbon capture processes. In a literary study, the operation of three basic carbon capture systems is described. Also different methods to transport carbon dioxide and carbon dioxide storage options are described in this section. At the end of the thesis processes that consume most of the auxiliary power are defined and possibilities to reduce the auxiliary power consumption are evaluated. Cost of carbon capture, transport and storage are also evaluated at this point and in the case that the carbon capture and storage systems are fully deployed. According to the results, it can be estimated what are the processes are where variable speed drives can be used and what kind of cost and power consumption reduction could be achieved. Results also show how large a project carbon capture and storage is if it is fully deployed.

Market Opportunities for Paper Industry in Radio Frequency Identification

The paper industry has been experiencing remarkable structural changes since paper demand growth has ceased and some markets are declining. One reason behind the declined demand is the Internet, which has partially substituted the newspaper as a source of information. Paper products alone can no longer provide livelihood, and the paper industry has to find new business areas. In this research, we studied radio frequency identification (RFID), and the market opportunities it could provide for paper industry. The research combined a quantitative industry analysis and qualitative interviews. RFID is a growing industry in the beginning of its life cycle, in which value chains and technologies still evolve significantly. The industry is going to concentrate on the future, and in the long term RFID-identifiers will probably be printed on paper substrate or directly onto products. Paper industry has the chance to enter the RFID industry, but it has to obtain the required competences, for example through acquisitions. The business potential RFID offers to paper industry is inadequate, and while reviewing new strategic options, the paper industry must consider more options, for example the entire printed intelligence.

Taajuusmuuttajaohjatun pumppukäytön simulointimallin kehittäminen ja testaus

Pumppukäytöt vastaavat noin neljänneksestä Euroopan sähkömoottoreissa kulutettavasta sähkötehosta. Energian kallistumisen vuoksi energian säästämisestä ja energiatehokkuudesta on tullut yhä tärkeämpää. Taajuusmuuttajat ovat tuoneet yksinkertaisen säätötavan, jolla suurimmassa osassa pumppukäyttöjä voidaan saada huomattavia energiasäästöjä. Koko energiansäästöpotentiaalin hyödyntämiseksi täytyy kuitenkin pumppujen toimintaa tarkkailla. Tarkkailu voidaan toteuttaa käyttämällä taajuusmuuttajan sisäisiä mittauksia pumpun toimintapisteen määrittämiseen. Tässä työssä muodostetaan kaksi simulointimallia, joilla voidaan tutkia pumppukäytön toimintapistettä ja energiatehokkuutta. Pumpattavan nesteen ominaisuuksien vaikutusta malleihin tutkitaan ja tapoja korjata virhettä selvitetään. Mallien tuottamia estimaatteja verrataan laboratorio ja pilot-kohteiden mittauksiin. Pilot-kohteiden avulla tutkitaan voidaanko simulointimalleja käyttää teollisuuden energiansäästöpotentiaalia omaavien pumppukäyttöjen havaitsemiseen.

Taajuusmuttajan vanheneminen syklisissä käytöissä

Tässä työssä tarkastellaan taajuusmuuttajan vanhenemista syklisissä käytöissä puolijohdetehokomponenttien osalta. Laitteiden vikaantumisprosessien analysoimiseksi työssä suunnitellaan syklinen kestotestausjärjestelmä, joka mahdollistaa useamman taajuusmuuttajan yhtäaikaisen vanhentamisen. Jaksottaisesti toistuvat kuormitussyklit rasittavat termomekaanisesti taajuusmuuttajan tehomoduulin sisäisiä rakenteita suurten lämpötilavaihtelujen johdosta. Teoriaosuuden pääpaino kohdistuu puolijohdetehokomponenttien rakenteeseen, vikaantumisprosesseihin ja eliniän kartoittamiseen. Työssä käydään läpi yleisimpien pienijännitteisten moottorinohjausinverttereiden tehomoduulien mekaaniset rakenteet, tyypillisemmät syklisestä kuormituksesta johtuvat vikaantumisprosessit sekä puolijohdetehokomponenttivalmistajien käyttämät syklisen eliniän testausmenetelmät. Loppuosassa työtä suunnitellaan taajuusmuuttajan syklinen kestotestausjärjestelmä laitteiden keinotekoista vanhentamista varten. Testausjärjestelmällä voidaan kuormittaa useampaa taajuusmuuttajaa vuorottain mielivaltaisella kuormitusvirtaprofiililla. Laitteita vanhennettiin kaksi testierää kuormittamalla niitä jaksottaisesti hissikäytön tyypillisellä kuormitusprofiililla. Puolijohdetehokomponentin vanhenemisen edistystä seurattiin termisen impedanssiketjun mittausmenetelmällä, joka perustuu IGBT:n kollektoriemitterijännitteen lämpötilariippuvuuteen. Testilaitteiden puolijohdetehokomponentit hajosivat syklisen eliniän päättymiseen teoriassa esitettyjen vikaantumisprosessien seurauksesta. Tehomoduulien vika-analyysi osoittaa syklisen kestotestausjärjestelmän soveltuvaksi menetelmäksi tutkia erilaisten kuormitusprofiilien vaikutusta taajuusmuuttajan vanhenemiseen.

Shaping urban traffic patterns through congestion charging : What factors drive success or failure?

Congestion costs are emerging as one of the most important challenges faced by metropolitan planners and transport authorities in first world economies. In US these costs were as high as 78 million dollars in 2005 and are growing due to fast increases in travel delays. In order to solve the current and severe levels of congestion the US department of transportation have recently started a program to initiate congestion pricing in five metropolitan areas. In this context it is important to determine those factors helping its implementation and success, but also the problems or difficulties associated with charging projects. In this article we analyze worldwide experiences with urban road charging in order to extract interesting and helpful lessons for policy makers engaged in congestion pricing projects and for those interested in the introduction of traffic management tools to regulate the entrance to big cities.

Regulating Concessions of Toll Motorways, An Empirical Study on Fixed vs. Variable Term Contracts

Recent theoretical developments on concession contracts for long term infrastructure projects under uncertain demand show the benefits of allowing for flexible term contracts rather than fixing a rigid term. This study presents a simulation to compare both alternatives by using real data from the oldest Spanish toll motorway. For this purpose, we analyze how well the flexible term would have performed instead of the fixed length actually established. Our results show a huge reduction of the term of concession that would have dramatically decreased the firm’s benefits and the user’s overpayment due to the internalization of an unexpected traffic increase.

Kalman Filtering in Online Paper Quality Assessment

Controlling the quality variables (such as basis weight, moisture etc.) is a vital part of making top quality paper or board. In this thesis, an advanced data assimilation tool is applied to the quality control system (QCS) of a paper or board machine. The functionality of the QCS is based on quality observations that are measured with a traversing scanner making a zigzag path. The basic idea is the following: The measured quality variable has to be separated into its machine direction (MD) and cross direction (CD) variations due to the fact that the QCS works separately in MD and CD. Traditionally this is done simply by assuming one scan of the zigzag path to be the CD profile and its mean value to be one point of the MD trend. In this thesis, a more advanced method is introduced. The fundamental idea is to use the signals’ frequency components to represent the variation in both CD and MD. To be able to get to the frequency domain, the Fourier transform is utilized. The frequency domain, that is, the Fourier components are then used as a state vector in a Kalman filter. The Kalman filter is a widely used data assimilation tool to combine noisy observations with a model. The observations here refer to the quality measurements and the model to the Fourier frequency components. By implementing the two dimensional Fourier transform into the Kalman filter, we get an advanced tool for the separation of CD and MD components in total variation or, to be more general, for data assimilation. A piece of a paper roll is analyzed and this tool is applied to model the dataset. As a result, it is clear that the Kalman filter algorithm is able to reconstruct the main features of the dataset from a zigzag path. Although the results are made with a very short sample of paper roll, it seems that this method has great potential to be used later on as a part of the quality control system.

Regression analysis of compositional data when both the dependent variable and independent variable are components

It is well known that regression analyses involving compositional data need special attention because the data are not of full rank. For a regression analysis where both the dependent and independent variable are components we propose a transformation of the components emphasizing their role as dependent and independent variables. A simple linear regression can be performed on the transformed components. The regression line can be depicted in a ternary diagram facilitating the interpretation of the analysis in terms of components. An exemple with time-budgets illustrates the method and the graphical features

Efectos del alcohol y conducción de vehículos: creencias y conductas de los jóvenes

Traffic accidents are one of the causes of death for people between 1 and 45 years old. Many studies verify that the road accidents are related with the consumption of alcohol. This problem, is especially important in the young people and it is increased during dawns of the weekends. Some studies underline the lack of information and knowledge of many young people concerning law on alcohol consummation when driving and the effects of this drug on consumers. Another problem is the amount of mistaken beliefs on what to do neutralize the alcohol’s effect before drive. The objective of our study is to evaluate, in university students, the knowledge of the rules of driving behavior included in the circulation code and the personal beliefs about the effects of the alcohol in driving, and to find the frequency and the circumstances in which young people drive after alcohol consummation. The results suggest many actions that may be considered in the design of preventive campaigns that promotes safety road behavior in order to increase their effectivity

Is there a relationship between bilingual language switching and executive functions in bilingualism? Introducing a within-group analysis approach

Several studies have suggested a bilingual advantage in executive functions, presumably due to bilinguals' massive practice with language switching that requires executive resources, but the results are still somewhat controversial. Previous studies are also plagued by the inherent limitations of a natural groups design where the participant groups are bound to differ in many ways in addition to the variable used to classify them. In an attempt to introduce a complementary analysis approach, we employed multiple regression to study whether the performance of 30- to 75-year-old FinnishSwedish bilinguals (N = 38) on tasks measuring different executive functions (inhibition, updating, and set shifting) could be predicted by the frequency of language switches in everyday life (as measured by a language switching questionnaire), L2 age of acquisition, or by the self-estimated degree of use of both languages in everyday life. Most consistent effects were found for the set shifting task where a higher rate of everyday language switches was related to a smaller mixing cost in errors. Mixing cost is thought to reflect top-down management of competing task sets, thus resembling the bilingual situation where decisions of which language to use has to be made in each conversation. These findings provide additional support to the idea that some executive functions in bilinguals are affected by a lifelong experience in language switching and, perhaps even more importantly, suggest a complementary approach to the study of this issue.

Position sensorless electrically excited synchronous motor drive for industrial use based on direct flux linkage and torque control

Synchronous machines with an AC converter are used mainly in large drives, for example in ship propulsion drives as well as in rolling mill drives in steel industry. These motors are used because of their high efficiency, high overload capacity and good performance in the field weakening area. Present day drives for electrically excited synchronous motors are equipped with position sensors. Most drives for electrically excited synchronous motors will be equipped with position sensors also in future. This kind of drives with good dynamics are mainly used in metal industry. Drives without a position sensor can be used e.g. in ship propulsion and in large pump and blower drives. Nowadays, these drives are equipped with a position sensor, too. The tendency is to avoid a position sensor if possible, since a sensor reduces the reliability of the drive and increases costs (latter is not very significant for large drives). A new control technique for a synchronous motor drive is a combination of the Direct Flux Linkage Control (DFLC) based on a voltage model and a supervising method (e.g. current model). This combination is called Direct Torque Control method (DTC). In the case of the position sensorless drive, the DTC can be implemented by using other supervising methods that keep the stator flux linkage origin centered. In this thesis, a method for the observation of the drift of the real stator flux linkage in the DTC drive is introduced. It is also shown how this method can be used as a supervising method that keeps the stator flux linkage origin centered in the case of the DTC. In the position sensorless case, a synchronous motor can be started up with the DTC control, when a method for the determination of the initial rotor position presented in this thesis is used. The load characteristics of such a drive are not very good at low rotational speeds. Furthermore, continuous operation at a zero speed and at a low rotational speed is not possible, which is partly due to the problems related to the flux linkage estimate. For operation in a low speed area, a stator current control method based on the DFLC modulator (DMCQ is presented. With the DMCC, it is possible to start up and operate a synchronous motor at a zero speed and at low rotational speeds in general. The DMCC is necessary in situations where high torque (e.g. nominal torque) is required at the starting moment, or if the motor runs several seconds at a zero speed or at a low speed range (up to 2 Hz). The behaviour of the described methods is shown with test results. The test results are presented for the direct flux linkage and torque controlled test drive system with a 14.5 kVA, four pole salient pole synchronous motor with a damper winding and electric excitation. The static accuracy of the drive is verified by measuring the torque in a static load operation, and the dynamics of the drive is proven in load transient tests. The performance of the drive concept presented in this work is sufficient e.g. for ship propulsion and for large pump drives. Furthermore, the developed methods are almost independent of the machine parameters.

Salient Pole Synchronous Machine Modelling in an Industrial Direct Torque Controlled Drive Application

Synchronous motors are used mainly in large drives, for example in ship propulsion systems and in steel factories' rolling mills because of their high efficiency, high overload capacity and good performance in the field weakening range. This, however, requires an extremely good torque control system. A fast torque response and a torque accuracy are basic requirements for such a drive. For large power, high dynamic performance drives the commonly known principle of field oriented vector control has been used solely hitherto, but nowadays it is not the only way to implement such a drive. A new control method Direct Torque Control (DTC) has also emerged. The performance of such a high quality torque control as DTC in dynamically demanding industrial applications is mainly based on the accurate estimate of the various flux linkages' space vectors. Nowadays industrial motor control systems are real time applications with restricted calculation capacity. At the same time the control system requires a simple, fast calculable and reasonably accurate motor model. In this work a method to handle these problems in a Direct Torque Controlled (DTC) salient pole synchronous motor drive is proposed. A motor model which combines the induction law based "voltage model" and motor inductance parameters based "current model" is presented. The voltage model operates as a main model and is calculated at a very fast sampling rate (for example 40 kHz). The stator flux linkage calculated via integration from the stator voltages is corrected using the stator flux linkage computed from the current model. The current model acts as a supervisor that prevents only the motor stator flux linkage from drifting erroneous during longer time intervals. At very low speeds the role of the current model is emphasised but, nevertheless, the voltage model always stays the main model. At higher speeds the function of the current model correction is to act as a stabiliser of the control system. The current model contains a set of inductance parameters which must be known. The validation of the current model in steady state is not self evident. It depends on the accuracy of the saturated value of the inductances. Parameter measurement of the motor model where the supply inverter is used as a measurement signal generator is presented. This so called identification run can be performed prior to delivery or during drive commissioning. A derivation method for the inductance models used for the representation of the saturation effects is proposed. The performance of the electrically excited synchronous motor supplied with the DTC inverter is proven with experimental results. It is shown that it is possible to obtain a good static accuracy of the DTC's torque controller for an electrically excited synchronous motor. The dynamic response is fast and a new operation point is achieved without oscillation. The operation is stable throughout the speed range. The modelling of the magnetising inductance saturation is essential and cross saturation has to be considered as well. The effect of cross saturation is very significant. A DTC inverter can be used as a measuring equipment and the parameters needed for the motor model can be defined by the inverter itself. The main advantage is that the parameters defined are measured in similar magnetic operation conditions and no disagreement between the parameters will exist. The inductance models generated are adequate to meet the requirements of dynamically demanding drives.

Food Frequency Questionnaires (FFQ) para el estudio del consumo de cacao en estudiantes de ciencias de la salud

Tot i que el cacau i la xocolata són una gran font de polifenols, aquests aliments no es troben entre les fonts alimentàries de polifenols més consumides. Algunes dades suggereixen un aport inferior al 10% de polifenols a través d’aquests. Aquest fet podria ser causa de les diferents metodologies i l'enfocament dels qüestionaris de freqüència de consum d'aliments (FFQ) utilitzats en aquests estudis. La majoria de FFQ validats utilitzen una extensa llista d'aliments per a les fruites i verdures, però no distingeixen adequadament les diverses fonts de xocolata i cacau. Aquests fets recolzen la necessitat d'una avaluació del consum de productes de cacau per tal de poder conèixer la ingesta real de cacau, especialment en la població jove, on la xocolata és un aliment consumit freqüentment.

An Interface Damage Model for the Simulation of Delamination Under Variable-Mode Ratio in Composite Materials

A thermodynamically consistent damage model for the simulation of progressive delamination under variable mode ratio is presented. The model is formulated in the context of the Damage Mechanics. The constitutive equation that results from the definition of the free energy as a function of a damage variable is used to model the initiation and propagation of delamination. A new delamination initiation criterion is developed to assure that the formulation can account for changes in the loading mode in a thermodynamically consistent way. The formulation proposed accounts for crack closure effets avoiding interfacial penetration of two adjacent layers aftercomplete decohesion. The model is implemented in a finite element formulation. The numerical predictions given by the model are compared with experimental results

Pla de màrqueting per al llançament d'un nou producte en el mercat dels motors elèctrics per a bancs de proves

Ningú no dubte ja del canvi de mentalitat que s’ha produït en els darrers anys en els compradors pel què fa al mercat de l’automòbil. La seguretat i el respecte per el medi ambient, són actualment dos dels factors claus que el consumidor té en compte a l’hora de comprar un vehicle. D’altra banda en els darrers anys la Unió Europea, ha fixat tota una sèrie normatives per tal de reduir les emissions nocives a l’atmosfera. Així doncs, més seguretat i menys emissions, signifiquen vehicles que incorporin components i sistemas cada cop més sofisticats, els quals, a la vegada, necessiten de bancs d’assaig i equips de test per tal de ser validats. Aquest fet ha provocat una revolució dins dels sistemes de test per a vehicles, per als quals han augmentat enormement les exigències en quan a precisions i repetibilitat per tal d’intentar reproduir, amb la màxima fiabilitat possible, les condicions de treball que hauran de suportar els components durant el seu ús real. Les característiques dels motors elèctrics, resulten ideals per a accionar aquest tipus d’aplicacions, ja que permeten un control del parell molt acurat i una repetibilitat quasi perfecte enfront d’altres sistemas utilitzats fins no fa massa temps. Aquesta demanda creixent d’aquest tipus de màquines elèctriques, obra una nova oportunitat de negoci per a les empreses fabricants de motors elèctrics. L’objectiu principal d’aquest treball és identificar i satisfer les necessitats dels clients, dins d’un mercat industrial concret: el mercat dels motors elèctrics per a bancs de proves de components per a la indústria de l’automoció. La fita és doncs la de proporcionar les eines necessàries per tal de que una empresa, fabricant de motors elèctrics de velocitat variable, pugui realitzar el disseny, desenvolupament i llançament comercial d’un nou tipus de motor, específicament pensat per aquest mercat, amb les màximes garanties d’èxit. Com a principal conclusió, el treball argumenta que el nou producte representa una oportunitat de negoci força atractiva i rendible per a l’empresa, i permetrà diversificar la oferta de la companyia cap a un nou sector fins ara no explotat.