Cultural distance and negotiation behavior : Perception of entrepreneurs operating in Turku

This thesis investigates the influence of cultural distance on entrepreneurs’ negotiation behaviour. For this purpose, Turku was chosen as the unit of analysis due to the exponential demographic change experienced during the last two decades that has derived in a more diversified local environment. The research aim set for this study was to identify to what extent entrepreneurs face cultural distance, how cultural distance influences the entrepreneur’s negotiation behaviour and how can it be addressed in order to turn dissimilarities into opportunities. This study presented the relation and apparent dichotomy of cultural distance and global culture, including the component of diversity. The impact of cultural distance in the entrepreneurial mindset and its consequent effect in negotiation behaviour was presented too. Addressing questions about the way individuals perceive, behave and interact allowed the use of interviews for this qualitative research study. In the empirical part of this study it was found that negotiation behaviour differed in terms of how congenial entrepreneurs felt when managing cultural distance, encompassing their performance. It was also acknowledged that after time and effort, some of the personal traits were enhanced while others reduced, allowing for more flexibility and adaptation. Furthermore, depending on the level of trust and shared interests, entrepreneurs determined their attitudinal approach, being adaptive or reactive subject to situational aspects. Additionally, it was found that the acquisition of cultural savvy not necessarily conveyed to more creativity. This experiential learning capability led to the proposition of new ways of behaviour. Likewise, it was proposed that growing cultural intelligence bridge distances, reducing mistrusts and misunderstandings. The capability of building more collaborative relationships allows entrepreneurs to see cultural distance as a cultural perspective instead of as a threat. Therefore it was recommended to focus on proximity rather than distance to better identify and exploit untapped opportunities and better perform when negotiating in whichever cultural conditions.

Supply network risks and costs in Finnish project business

This report summarizes the results of the survey HAVERI – Supply network risks in business. The survey was conducted in Finland during the spring and summer of year 2013. The survey is part of a large two-year research project started in June 2012 in Finland (on-going 06/2012–07/2014). The project is launched and financed by TEKES, the Finnish Funding Agency for Technology and Innovation, and executed together with the researchers from Lappeenranta University of Technology and Tampere University of Technology. The overall goal of this on-going research project is to find out the decision-making practices in the project-oriented companies in their purchasing decisions especially in the mechanical engineering and construction industries in Finland. The objective of the survey was to gain cross-sectional data concerning the challenges, risks and cost factors in Finnish project business companies. The results show that Finnish companies rely on their experience and supplier references in their risk management. In general, the understanding of the total cost structure varies among the industries and companies. The main cost factor in risk management was costs before the actual purchase decision. Overall, it seems that the monetary value of the whole project and capability of purchasing personnel are the main influencing factors on risk management activity in project purchasing.

Michelson interferometer with porch swing bearing for portable FTIR spectrometer

The interferometer for low resolution portable Fourier Transform middle infrared spectrometer was developed and studied experimentally. The final aim was a concept for a commercial prototype. Because of the portability, the interferometer should be compact sized and insensitive to the external temperature variations and mechanical vibrations. To minimise the size and manufacturing costs, Michelson interferometer based on plane mirrors and porch swing bearing was selected and no dynamic alignment system was applied. The driving motor was a linear voice coil actuator to avoid mechanical contact of the moving parts. The driving capability for low mirror driving velocities required by the photoacoustic detectors was studied. In total, four versions of such an interferometer were built and experimentally studied. The thermal stability during the external temperature variations and the alignment stability over the mirror travel were measured using the modulation depth of the wide diameter laser beam. Method for estimating the mirror tilt angle from the modulation depth was developed to take account the effect from the non-uniform intensity distribution of the laser beam. The spectrometer stability was finally studied also using the infrared radiation. The latest interferometer was assembled for the middle infrared spectrometer with spectral range from 750 cm−1 to 4500 cm−1. The interferometer size was (197 × 95 × 79) mm3 with the beam diameter of 25 mm. The alignment stability as the change of the tilt angle over the mirror travel of 3 mm was 5 μrad, which decreases the modulation depth only about 0.7 percent in infrared at 3000 cm−1. During the temperature raise, the modulation depth at 3000 cm−1 changed about 1 . . . 2 percentage units per Celsius over short term and even less than 0.2 percentage units per Celsius over the total temperature raise of 30 °C. The unapodised spectral resolution was 4 cm−1 limited by the aperture size. The best achieved signal to noise ratio was about 38 000:1 with commercially available DLaTGS detector. Although the vibration sensitivity requires still improving, the interferometer performed, as a whole, very well and could be further developed to conform all the requirements of the portable and stable spectrometer.

Modular framework for outlier detection

Outlier detection is an important form of data analysis because outliers in several cases contain the interesting and important pieces of information. In the recent years, many different outlier detection algorithms have been devised for finding different kinds of outliers in varying contexts and environments. Some effort has been put to study how to effectively combine different outlier detection methods. The combination of outlier detection algorithms as an ensemble was studied in this thesis by designing a modular framework for outlier detection, which combines arbitrary outlier detection techniques. This work resulted in an example implementation of the framework. Outlier detection capability of the ensemble method was validated using datasets and methods found in outlier detection research. The framework achieved better results than the individual outlier algorithms. Future research includes how to handle large datasets effectively and the possibilities for real-time outlier monitoring.

Kestomagneettitahtikonekäyttöjen erot

Permanent magnet drives with nominal power over 10 kW were not a cost-sufficient system 25 years ago due to high material expenses. The improvements in motor drives, the rise in competition and the tightening of standards and regulations have caused that the PM-drives are more and more common in the over 10 kW nominal power range. The goal of this thesis is to research the performance in relation to nominal power of a PM-drive technique that is vastly increasing its popularity in fan related devices. The studied motor technique brushless direct current drive (BLDC) consists of a voltage source inverter, permanent motor and six-step-control. The reference drive is a brushless alternating current drive (BLAC) which consists of a VSI, PM and a hysteresis control. As a conclusion there are no major obstacles that would impede the BLDC-drive technique from expanding to larger power stages. The following factors must be taken into consideration when designing a BLDC-drive: motor’s current change rate, inverter switching frequency, motor’s nominal electric frequency, phase inductance and the current handling capability of the inverter. The fluctuating material costs create instability to the end prices of PM-motors that can in the worst case lead to diminished interest towards BLDC- and PM-drives in general.

Upconverting diagnostics: Multiplex assays utilizing upconversion luminescence technology

Conventional diagnostics tests and technologies typically allow only a single analysis and result per test. The aim of this study was to propose robust and multiplex array-inwell test platforms based on oligonucleotide and protein arrays combining the advantages of simple instrumentation and upconverting phosphor (UCP) reporter technology. The UCPs are luminescent lanthanide-doped crystals that have a unique capability to convert infrared radiation into visible light. No autofluorescence is produced from the sample under infrared excitation enabling the development of highly sensitive assays. In this study, an oligonucleotide array-in-well hybridization assay was developed for the detection and genotyping of human adenoviruses. The study provided a verification of the advantages and potential of the UCP-based reporter technology in multiplex assays as well as anti-Stokes photoluminescence detection with a new anti- Stokes photoluminescence imager. The developed assay was technically improved and used to detect and genotype adenovirus types from clinical specimens. Based on the results of the epidemiological study, an outbreak of adenovirus type B03 was observed in the autumn of 2010. A quantitative array-in-well immunoassay was developed for three target analytes (prostate specific antigen, thyroid stimulating hormone, and luteinizing hormone). In this study, quantitative results were obtained for each analyte and the analytical sensitivities in buffer were in clinically relevant range. Another protein-based array-inwell assay was developed for multiplex serodiagnostics. The developed assay was able to detect parvovirus B19 IgG and adenovirus IgG antibodies simultaneously from serum samples according to reference assays. The study demonstrated that the UCPtechnology is a robust detection method for diverse multiplex imaging-based array-inwell assays.

Power semiconductor nonlinearities in active du/dt output filtering

This doctoral thesis introduces an improved control principle for active du/dt output filtering in variable-speed AC drives, together with performance comparisons with previous filtering methods. The effects of power semiconductor nonlinearities on the output filtering performance are investigated. The nonlinearities include the timing deviation and the voltage pulse waveform distortion in the variable-speed AC drive output bridge. Active du/dt output filtering (ADUDT) is a method to mitigate motor overvoltages in variable-speed AC drives with long motor cables. It is a quite recent addition to the du/dt reduction methods available. This thesis improves on the existing control method for the filter, and concentrates on the lowvoltage (below 1 kV AC) two-level voltage-source inverter implementation of the method. The ADUDT uses narrow voltage pulses having a duration in the order of a microsecond from an IGBT (insulated gate bipolar transistor) inverter to control the output voltage of a tuned LC filter circuit. The filter output voltage has thus increased slope transition times at the rising and falling edges, with an opportunity of no overshoot. The effect of the longer slope transition times is a reduction in the du/dt of the voltage fed to the motor cable. Lower du/dt values result in a reduction in the overvoltage effects on the motor terminals. Compared with traditional output filtering methods to accomplish this task, the active du/dt filtering provides lower inductance values and a smaller physical size of the filter itself. The filter circuit weight can also be reduced. However, the power semiconductor nonlinearities skew the filter control pulse pattern, resulting in control deviation. This deviation introduces unwanted overshoot and resonance in the filter. The controlmethod proposed in this thesis is able to directly compensate for the dead time-induced zero-current clamping (ZCC) effect in the pulse pattern. It gives more flexibility to the pattern structure, which could help in the timing deviation compensation design. Previous studies have shown that when a motor load current flows in the filter circuit and the inverter, the phase leg blanking times distort the voltage pulse sequence fed to the filter input. These blanking times are caused by excessively large dead time values between the IGBT control pulses. Moreover, the various switching timing distortions, present in realworld electronics when operating with a microsecond timescale, bring additional skew to the control. Left uncompensated, this results in distortion of the filter input voltage and a filter self-induced overvoltage in the form of an overshoot. This overshoot adds to the voltage appearing at the motor terminals, thus increasing the transient voltage amplitude at the motor. This doctoral thesis investigates the magnitude of such timing deviation effects. If the motor load current is left uncompensated in the control, the filter output voltage can overshoot up to double the input voltage amplitude. IGBT nonlinearities were observed to cause a smaller overshoot, in the order of 30%. This thesis introduces an improved ADUDT control method that is able to compensate for phase leg blanking times, giving flexibility to the pulse pattern structure and dead times. The control method is still sensitive to timing deviations, and their effect is investigated. A simple approach of using a fixed delay compensation value was tried in the test setup measurements. The ADUDT method with the new control algorithm was found to work in an actual motor drive application. Judging by the simulation results, with the delay compensation, the method should ultimately enable an output voltage performance and a du/dt reduction that are free from residual overshoot effects. The proposed control algorithm is not strictly required for successful ADUDT operation: It is possible to precalculate the pulse patterns by iteration and then for instance store them into a look-up table inside the control electronics. Rather, the newly developed control method is a mathematical tool for solving the ADUDT control pulses. It does not contain the timing deviation compensation (from the logic-level command to the phase leg output voltage), and as such is not able to remove the timing deviation effects that cause error and overshoot in the filter. When the timing deviation compensation has to be tuned-in in the control pattern, the precalculated iteration method could prove simpler and equally good (or even better) compared with the mathematical solution with a separate timing compensation module. One of the key findings in this thesis is the conclusion that the correctness of the pulse pattern structure, in the sense of ZCC and predicted pulse timings, cannot be separated from the timing deviations. The usefulness of the correctly calculated pattern is reduced by the voltage edge timing errors. The doctoral thesis provides an introductory background chapter on variable-speed AC drives and the problem of motor overvoltages and takes a look at traditional solutions for overvoltage mitigation. Previous results related to the active du/dt filtering are discussed. The basic operation principle and design of the filter have been studied previously. The effect of load current in the filter and the basic idea of compensation have been presented in the past. However, there was no direct way of including the dead time in the control (except for solving the pulse pattern manually by iteration), and the magnitude of nonlinearity effects had not been investigated. The enhanced control principle with the dead time handling capability and a case study of the test setup timing deviations are the main contributions of this doctoral thesis. The simulation and experimental setup results show that the proposed control method can be used in an actual drive. Loss measurements and a comparison of active du/dt output filtering with traditional output filtering methods are also presented in the work. Two different ADUDT filter designs are included, with ferrite core and air core inductors. Other filters included in the tests were a passive du/dtfilter and a passive sine filter. The loss measurements incorporated a silicon carbide diode-equipped IGBT module, and the results show lower losses with these new device technologies. The new control principle was measured in a 43 A load current motor drive system and was able to bring the filter output peak voltage from 980 V (the previous control principle) down to 680 V in a 540 V average DC link voltage variable-speed drive. A 200 m motor cable was used, and the filter losses for the active du/dt methods were 111W–126 W versus 184 W for the passive du/dt. In terms of inverter and filter losses, the active du/dt filtering method had a 1.82-fold increase in losses compared with an all-passive traditional du/dt output filter. The filter mass with the active du/dt method was 17% (2.4 kg, air-core inductors) compared with 14 kg of the passive du/dt method filter. Silicon carbide freewheeling diodes were found to reduce the inverter losses in the active du/dt filtering by 18% compared with the same IGBT module with silicon diodes. For a 200 m cable length, the average peak voltage at the motor terminals was 1050 V with no filter, 960 V for the all-passive du/dt filter, and 700 V for the active du/dt filtering applying the new control principle.

Syvää vai pelkästään tiheää : neuvostoliittolaisen ja venäläisen sotataidollisen ajattelun lähtökohdat, kehittyminen, soveltaminen käytäntöön ja nykytilanne. Näkökulmana 1920- ja 1930-luvun syvän taistelun ja operaation opit

Sosialistisen vallankumouksen jälkeen Neuvosto-Venäjän oli monien muiden kysymysten ohella ratkaistava sosialismin saavutusten puolustaminen. Aluksi ratkaisuksi suunniteltiin vapaaehtoisuuteen perustuvaa punakaartia, mutta riittävän miesvahvuuden turvaamiseksi päädyttiin yleiseen asevelvollisuuteen. Pian Venäjän sisällissodan jälkeen sotataidon suunta painottui enemmän vanhan armeijan asiantuntijoiden näkemysten kuin vallankumoussankarien kokemusten mukaiseksi, vaikka Frunzen puna-armeijalle kirjoittama doktriini perustui luokkataisteluun ja korosti sisällissodassa hyväksi koettua operatiivista liikkuvuutta. Neuvostoliiton ja Venäjän sotataidon perustana on Pietari I:n aloittama länsimainen suuntaus, jota kuitenkin täydentävät vahvat kansalliset piirteet. Venäläisen sotataidon henkisenä isänä voidaan hyvällä syyllä pitää Aleksandr Suvorovia, jonka opetukset näkyvät tekstilainausten lisäksi myös periaatteissa ja sotilaskasvatuksessa. Napoleonin sotien jälkeen perustettu Keisarillinen yleisesikunta-akatemia loi Venäjälle sotatieteellisen tutkimuksen ja opetuksen. Sotatieteen mahdollisuuksia ei 1800-luvun Venäjällä osattu täysin hyödyntää. Aseistuksen kasvavan tehon merkitystä vähättelevä asenne johti sotataidon taantumisen ja katastrofiin Venäjän–Japanin sodassa. Sen kokemuksia analysoidessaan Aleksandr Neznamov kehitti edelleen saksalaista operaation käsitettä ja loi perustan Neuvostoliitossa 1920-luvulla kehitetylle operaatiotaidolle. Neuvostoliittolaisen sotataidon päämääränä oli kehittää taktinen ja operatiivinen ratkaisu aseistuksen tehon kasvun aikaansaamaan puolustuksen ylivoimaisuuteen. Ratkaisussa hyödynnettiin brittien kokemuksia ja tutkimusta. Neuvostoliittolainen taktiikka ja operaatiotaito eivät kuitenkaan olleet brittiläisen mekanisoidun sodankäynnin tai saksalaisen salamasodan itäinen kopioita vaan itsenäisiin ratkaisuihin pohjautuvia. Syvän taistelun ja operaation teoriaa kokeiltiin harjoituksissa, ja sitä kehitettiin Stalinin vuoden 1937 puhdistuksiin saakka. Toisen maailmansodan taisteluissa puna-armeija sovelsi alkuvaiheen katastrofin jälkeen syvän taistelun ja syvän operaation oppeja. Komentajien ja joukkojen taito ei riittänyt teorian vaatimusten mukaiseen toimintaan, siksi syväksi aiotusta taistelusta tuli ajoittain ainoastaan tiheää. Suuren isänmaallisen sodan kokemusten perusteella neuvostoliittolainen sotatiede kehitti yleisjoukkojen taistelun periaatteet, jotka ovat säilyneet muuttumattomina nykypäivään saakka. Kylmän sodan aikakaudella ydin- ja tavanomaisen aseistuksen merkitys sodan ja taistelun kuvassa vaihteli. Lännen sotataidon ja aseteknologian kehitys pakotti Neuvostoliiton siirtymään 1980-luvulla sotilaallisessa ajattelussaan hyökkäyksestä puolustukseen. Neuvostoliiton hajoamisen jälkeen Venäjän sotilaallisen turvallisuuden takaajana on ydinaseistus. Yhdysvaltain tavanomainen ilma-avaruushyökkäyskyky vaatii Venäjää kehittämään torjuntajärjestelmiä. Tavanomaisten joukkojen rakentamisessa Venäjä seuraa tarkasti läntisen sotataidon kehittymistä, mutta pitäytyy omaperäisiin ratkaisuihin, joiden kehittämisessä sen vahvalla sotatieteellisellä järjestelmällä ja dialektisen materialismin metodilla on edelleen olennaisen tärkeä merkitys.

Particle model for simulating limestone reactions in novel fluidised bed energy applications

The development of carbon capture and storage (CCS) has raised interest towards novel fluidised bed (FB) energy applications. In these applications, limestone can be utilized for S02 and/or CO2 capture. The conditions in the new applications differ from the traditional atmospheric and pressurised circulating fluidised bed (CFB) combustion conditions in which the limestone is successfully used for SO2 capture. In this work, a detailed physical single particle model with a description of the mass and energy transfer inside the particle for limestone was developed. The novelty of this model was to take into account the simultaneous reactions, changing conditions, and the effect of advection. Especially, the capability to study the cyclic behaviour of limestone on both sides of the calcination-carbonation equilibrium curve is important in the novel conditions. The significances of including advection or assuming diffusion control were studied in calcination. Especially, the effect of advection in calcination reaction in the novel combustion atmosphere was shown. The model was tested against experimental data; sulphur capture was studied in a laboratory reactor in different fluidised bed conditions. Different Conversion levels and sulphation patterns were examined in different atmospheres for one limestone type. The Conversion curves were well predicted with the model, and the mechanisms leading to the Conversion patterns were explained with the model simulations. In this work, it was also evaluated whether the transient environment has an effect on the limestone behaviour compared to the averaged conditions and in which conditions the effect is the largest. The difference between the averaged and transient conditions was notable only in the conditions which were close to the calcination-carbonation equilibrium curve. The results of this study suggest that the development of a simplified particle model requires a proper understanding of physical and chemical processes taking place in the particle during the reactions. The results of the study will be required when analysing complex limestone reaction phenomena or when developing the description of limestone behaviour in comprehensive 3D process models. In order to transfer the experimental observations to furnace conditions, the relevant mechanisms that take place need to be understood before the important ones can be selected for 3D process model. This study revealed the sulphur capture behaviour under transient oxy-fuel conditions, which is important when the oxy-fuel CFB process and process model are developed.

DSpace REST API: an Interface for Reusing DSpace Content, and Practical Applications

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Uuden tiedon hankinta ja hyödyntäminen organisaation innovaatioprosesseissa

Tämän tutkimuksen tavoitteena oli tutkia, miten uuden ja erityisesti tulevaisuuteen suuntautuvan tiedon hankintaa ja hyödyntämistä organisaatioiden innovaatioprosesseissa voidaan tarkastella ja jäsentää sekä kehittää avoimen innovaatioteorioiden pohjalta. Tulevaisuustiedon järjestelmällinen hyödyntäminen on yhä tärkeämmässä asemassa 2010-luvun organisaatioiden innovatiivisuuden ja kilpailukyvyn kannalta. Tämä on abstraktin luonteensa vuoksi erittäin haasteellista mutta teoriassa mahdollista, jos uuden tiedon liittämisestä organisaation käyttöön on tehty tärkeä ja selkeä osa koko organisaation strategiaa. Uuden tiedon tehokkaaseen käsittelemiseen ja siirtämiseen organisaatiossa tarvitaan suunnitelmallista ennakointitoimintaa, sosiaalisia sovittelumekanismeja ja rakentavaa yhteistyötä myös ulkopuolisten toimijoiden kanssa. Valitun teoriakehyksen pohjalta laadittiin yksinkertaistettu kyselytutkimus, johon oli liitetty absorptiiviseen kapasiteettiin, visionääriseen kyvykkyyteen, ennakointitoimintaan ja uuden tiedon käsittelyyn liittyviä käsitteitä. Kyselyn tarkoituksena oli myös tarjota organisaatiolle mahdollisuus tarkastella nykyistä tilaansa uuden tiedon monivaiheisen hyödyntämisen kannalta. Kyselytutkimus lähetettiin suomalaisille teollisuusyrityksille ja saatuja vastauksia käytettiin empiirisenä aineistona. Empiiristä aineistoa tarkasteltiin kvantitatiivisin menetelmän ja tuloksista saatiin hyödyllistä tietoa yritysten toiminnasta käytännöntasolta.

Kestomagneettitahtikoneen vääntömomentin tuottokyvyn optimointi hybridibussikäyttöön

Työssä tarkastellaan hybridi- ja sähköajoneuvojen voimankäyttöjärjestelmiä ja bussin ajomoottorina toimivan kestomagneettitahtikoneen toimintaa ja sen soveltuvuutta ajoneuvokäyttöön. Esitetään analyyttinen työkalu kestomagneettitahtikoneen induktanssisuunnittelun ja koneen vääntömomentin tuottokyvyn optimoinnin tueksi. Työkalua hyödynnetään esitettävässä ajomoottorin mitoituslaskelmassa. Työssä päätellään, että kestomagneettitahtimoottori soveltuu hyvin ajoneuvokäyttöön. Maksimaalisen vääntömomentin saavuttamiseksi sen roottorin rakenne ja induktanssit on optimoitava. Analysoimalla ajoneuvokäyttöön tarkoitettua kestomagneettitahtimoottoria työkalun avulla havaitaan, että yhtä suuremmalla induktanssisuhteella vääntömomentti on pienempi kentänheikennyksessä kuin ajettaessa konetta taajuusmuuttajalla vakioteholla nimelliskuormalla. Vastaavasti yhtä pienemmillä induktanssisuhteilla vääntömomentti on pienempi kentänheikennyksessä. Todetaan, että vääntömomentti kasvaa induktanssisuhteen poiketessa yhdestä. Suuri vääntömomentti saadaan pienillä induktanssisuhteilla. Induktanssisuhteen kasvattaminen yhdestä ei lisää moottorin tuottamaa vääntömomenttia yhtä paljon kuin induktanssisuhteen pienentäminen. Työn lopuksi verrataan työkalun laskemia tuloksia kirjallisuudesta löytyvillä yhtälöillä laskettuihin tuloksiin. Työkalun laskemat tulokset vaikuttavat ristiriidattomilta ja yhteneväisiltä teorian kanssa. Työkalun toteutuksessa tehdyt teoreettiset yksinkertaistukset aiheuttavat todennäköisesti epätarkkuutta tuloksissa erityisesti suurella kuormituksella.

Ionic liquid mediated biomass deconstruction: from analysis challenges to fermentable sugars

Ionic liquids, ILs, have recently been studied with accelerating interest to be used for a deconstruction/fractionation, dissolution or pretreatment processing method of lignocellulosic biomass. ILs are usually utilized combined with heat. Regarding lignocellulosic recalcitrance toward fractionation and IL utilization, most of the studies concern IL utilization in the biomass fermentation process prior to the enzymatic hydrolysis step. It has been demonstrated that IL-pretreatment gives more efficient hydrolysis of the biomass polysaccharides than enzymatic hydrolysis alone. Both cellulose (especially cellulose) and lignin are very resistant towards fractionation and even dissolution methods. As an example, it can be mentioned that softwood, hardwood and grass-type plant species have different types of lignin structures leading to the fact that softwood lignin (guaiacyl lignin dominates) is the most difficult to solubilize or chemically disrupt. In addition to the known conventional biomass processing methods, several ILs have also been found to efficiently dissolve either cellulose and/or wood samples – different ILs are suitable for different purposes. An IL treatment of wood usually results in non-fibrous pulp, where lignin is not efficiently separated and wood components are selectively precipitated, as cellulose is not soluble or degradable in ionic liquids under mild conditions. Nevertheless, new ILs capable of rather good fractionation performance have recently emerged. The capability of the IL to dissolve or deconstruct wood or cellulose depends on several factors, (e.g. sample origin, the particle size of the biomass, mechanical treatments as pulverization, initial biomassto-IL ratio, water content of the biomass, possible impurities of IL, reaction conditions, temperature etc). The aim of this study was to obtain (fermentable) saccharides and other valuable chemicals from wood by a combined heat and IL-treatment. Thermal treatments alone contribute to the degradation of polysaccharides (e.g. 150 °C alone is said to cause the degradation of polysaccharides), thus temperatures below that should be used, if the research interest lies on the IL effectiveness. On the other hand, the efficiency of the IL-treatment can also be enhanced to combine other treatment methods, (e.g. microwave heating). The samples of spruce, pine and birch sawdust were treated with either 1-Ethyl-3-methylimidazolium chloride, Emim Cl, or 1-Ethyl-3-methylimidazolium acetate, Emim Ac, (or with ionized water for comparison) at various temperatures (where focus was between 80 and 120 °C). The samples were withdrawn at fixed time intervals (the main interest treatment time area lied between 0 and 100 hours). Double experiments were executed. The selected mono- and disaccharides, as well as their known degradation products, 5-hydroxymethylfurfural, 5-HMF, and furfural were analyzed with capillary electrophoresis, CE, and high-performance liquid chromatography, HPLC. Initially, even GC and GC-MS were utilized. Galactose, glucose, mannose and xylose were the main monosaccharides that were present in the wood samples exposed to ILs at elevated temperatures; in addition, furfural and 5-HMF were detected; moreover, the quantitative amount of the two latter ones were naturally increasing in line with the heating time or the IL:wood ratio.

Pk-yrityksen innovaatiokyvykkyyden maturiteettimalli

Tämä diplomityö on tehty suorituskyky johtamisen pääaineeseen ja sen tavoitteena on ollut suunnitella ja toteuttaa pieniin ja keskisuuriin yrityksiin soveltuva innovaatiokyvykkyyden maturiteetti- eli kypsyysmalli. Tutkimuksessa käytetään kvalitatiivista eli laadullista lähestymistapaa ja sovelletaan konstruktiivista tutkimusotetta. Tutkimuksen peruskäsitteet ovat innovaatio, innovatiivisuus ja innovaatiokyvykkyys. Innovaatio-käsite voidaan ymmärtää eräänlaiseksi synonyymiksi uutuudelle. Kattavin määritelmä innovaatiolle on ymmärtää se yksittäisen tapahtuman sijasta prosessina. Suorituskyvyn johtamisen näkökulmasta innovatiivisuutta voidaan pitää yhtenä yrityksen sisäisen suorituskyvyn kulmakivenä. Innovaatiokyky on osa yrityksen aineetonta pääomaa sekä organisaation suorituskyvyn ja menestymisen osa-alue ja taustatekijä. Yrityksen koko vaikuttaa sen innovaatiotoimintaan sekä määrällisesti käytettävien resurssien ja tehtävien investointien suuruutena että laadullisesti innovaatiotoiminnan organisoinnissa ja toteutuksessa. Innovaatiokyvykkyyden maturiteettimallin perusajatus on nähdä innovaatiokyvykkyys eteenpäin liikkuvana prosessina, jossa yritys tai organisaatio parantaa omaa asemaansa suhteessa ennalta määrättyihin innovaatiokyvykkyyden tekijöihin. Tutkimuksessa konstruoitu pk-yritysten innovaatiokyvykkyyden maturiteettimalli muodostuu kokonaisuudesta, jossa on kolme tekijää: mittaristo, maturiteettikuvio ja tasoportaat sekä nämä toisiinsa kytkevä innovaatiokyvykkyyden viitekehys. Mallin toimivuutta testattiin heikolla markkinatestillä suomalaisessa tietotekniikka-alan palveluyrityksen tuotekehitysorganisaatiossa. Tuloksien perusteella määritettiin case-organisaation maturiteettitaso. Lisäksi organisaatiosta löydettiin niin kehittämiskohteita kuin vahvuuksiakin.