Avaliação das condições de precipitação do azul da Prússia sobre pó de grafite visando o desenvolvimento de eletrodos de pasta de carbono para a quantificação de nitrito

An amperometric FIA method for nitrite quantification based on nitrite electroreduction and employing a carbon paste electrode (CPE) chemically modified with iron hexacyanoferrate (HCF) as an amperometric detector was developed. The influence of experimental conditions on the preparation of the electrode materials was evaluated and the materials obtained in each study were used for the development of modified electrodes. The electrochemical sensors were prepared by a fast, simple, and inexpensive procedure, and the long-term performance of the electrodes were quite satisfactory as the stability was maintained over one year. HCF was an effective redox mediator for nitrite electroreduction in acidic media, allowing nitrite detection at +0.2 V vs. Ag/AgClsat, which is a potential free of possible interfering species that are normally present in food and water samples. The electrochemical cell used in the FIA system was similar to a batch injection analysis cell, enabling recirculation of the carrier solution. This is an attractive feature because it allows the use of a high flow rate (6 mL min-1) leading to high sensitivity and analysis speed, while keeping reagent consumption low. The proposed method had a detection limit of 9 μmol L-1 and was successfully employed for nitrite quantification in spiked water and sausage samples. The obtained results were in good agreement with those provided by the spectrophotometric official method. At a 95 % confidence level it was not observed statistical differences neither in nitrite content nor in the precision provided by both methods. The experimental conditions for the synthesis of HCF were optimized and the best electrode material was prepared by mixing FeCl3, K4[Fe(CN)6] and carbon powder subjected to an acid and thermal treatment (400 ºC), followed by ultrasonic agitation at 4 °C. This material was used to construct an electrode with improved analytical performance to reduce nitrite, which presented greater stability compared to HCF film electrodeposited on the EPC, showing that the preparation procedure of the electrode material is an effective strategy for the development of HCF modified electrodes.

Atividade antiangiogênica da forma recombinante da proteína 21 de Trypanosoma cruzi

Chagas disease, caused by the parasite Trypanosoma cruzi, is the cause of Chronic chagasic cardiomyopathy (CCC). The prospection of innovative therapeutic agents against CCC is a major task. The recombinant form of 21 (rP21), a secreted T. cruzi protein involved in host cell invasion and on progression of chronic inflammatory processes have been studied as a potential novel therapeutic target. Our present work aimed to verify and investigate the impact of rP21 in the formation of blood vessels in vitro and in vivo. First, tEnd cells were treated with different concentrations of rP21 or bacterial extract and viability and cellular adhesion were evaluated by MTT and angiogenesis inhibition by Matrigel tube formation assay and murine model. To verify the proteolytic activity of rP21 on extracellular matrix (ECM) components, fibrinogen, matrigel and fibronectin was incubated with rP21 or not. In addition, we performed proliferation assays and cell cycle analysis. Furthermore, the accumulation and distribution of F-actin was determined by Phalloidin staining using ImageJ software. Finally, tEnd cells were incubated with rP21 and the mRNA levels were analyzed by real-time PCR. Our results showed that rP21 did not alter cell viability and adhesion, but strongly inhibited vessel formation in vitro and in vivo. Tube formation assay showed that angiogenesis inhibition was dependent of the CXCR4-rP21 binding. In addition to these results, we observed that the rP21 was able to inhibit cell proliferation and promoted a significant reduction in the number of 4n cells (G2/M phase). Moreover, we found that rP21 significantly increased F-actin levels and this protein was able to modulate expression of genes related to angiogenesis and actin cytoskeleton. However, rP21 showed no significant activity on the matrix components. In this sense, we conclude that the rP21-endothelial cells (ECs) interaction via CXCR4 promotes inhibition of vessel formation through a cascade of intracellular events, such as inhibition of ECs proliferation and modulation of the expression of molecules associated with angiogenic processes and actin cytoskeleton.

Análise da força propulsora do motor de indução linear alimentado com imposição de corrente

This work intent to study the motive power provided by the plane linear induction motor, in a lock condition. It uses a method of imposition of the electric current to the stator via a frequency convertor PWM driven by a refed platform. The reading of the motive power was performed by a load cell using an electronic circuit for reading and conditioning of the signal. Aiming a complete analysis of the linear motor, it was performed a computational modeling that employs all relevant parameters to the study of the locked machine. At the end it was held a theoric-experimental confrontation that evaluated the effectiveness of the proposed method.

Desarrollo de herramientas bioinformáticas para estudios de proteómica a gran escala de "Candida albicans"

El concepto de Proteómica, acuñado en analogía al de Genómica, fue usado por primera vez por Marc Wilkins a mediados de los años 90 para describir al conjunto total de proteínas que se expresan por los genes de una célula, tejido u organismo. Anteriormente, a finales de los 80, el desarrollo de las técnicas de ionización suave, como la Ionización por Electrospray, ESI (Electrospray Ionization) o la Desorción Suave por Láser, SLD (Soft Laser Desorption), permitió ionizar grandes biomoléculas como los péptidos y proteínas manteniéndolas relativamente intactas. Esto sentó las bases de la espectrometría de masas aplicada a la proteómica. En la proteómica shotgun (el término inglés está muy asentado), el primer paso del experimento generalmente consiste en la digestión de las proteínas de la muestra en péptidos por acción de una enzima proteolítica como la tripsina. Esto incrementa notablmente el rendimiento en términos de número de proteínas que pueden ser identificadas en un sólo experimento comparado con los experimentos basados en gel. Sin embargo, tiene el coste asociado de provocar una gran complejidad de la mezcla de péptidos y el problema añadido de la inferencia de las proteínas originarias. Los péptidos son separados por cromatografía líquida e ionizados para entrar a continuación en el espectrómetro de masas donde son separados en función de la proporción entre su masa y su carga (m/z) y los valores obtenidos son registrados en un espectro MS1. En la espectrometría de masas en tándem (MS/MS), los péptidos con mayor intensidad son seleccionados para ser fragmentados de modo que se generan espectros MS/MS, colecciones de valores m/z y de intensidad para cada precursor y sus fragmentos...

Variabilidad de la inactivación microbiana y de la fase de latencia de los microorganismos supervivientes a un proceso de acidificación

A la industria alimentaria se le exigen productos seguros, nutritivos, apetecibles y de uso cómodo y rápido. Aunar todos esos calificativos en un solo alimento es ardua tarea. Valgan dos ejemplos. Un tratamiento conservante intenso, de buenas perspectivas sanitarias, suele conllevar una pérdida de valor nutritivo y unas características sensoriales poco atractivas. El manejo de los alimentos para transformarlos en productos listos pare el consumo implica la asunción de ciertos riesgos microbiológicos, mayores que los asumidos en productos sin manipulación. ¿Cómo responder ante el incremento de riesgos y peligros que se ciernen sobre los “nuevos alimentos”? Una alternativa que ha ganado correligionarios es la microbiología predictiva. Es una herramienta útil, a disposición de cualquier entidad interesada en los alimentos, que predice, mediante modelos matemáticos, el comportamiento microbiano bajo ciertas condiciones. La mayoría de los modelos disponibles predicen valores únicos (a cada valor de la variable independiente le corresponde un único valor de la dependiente); han demostrado su eficacia durante décadas a base de tratamientos sobredimensionados para salvaguardar la calidad microbiológica de los alimentos y predicen una media, sin considerar la variabilidad. Considérese un valor de reducción decimal, D, de 1 minuto. Si el producto contiene 103 ufc/g, un envase de 1 Kg que haya pasado por un tratamiento 6D, contendrá 1 célula viable. Hasta aquí la predicción de un modelo clásico. Ahora piénsese en una producción industrial, miles de envases de 1 Kg/h. ¿Quién puede creerse que en todos ellos habrá 1 microorganismo superviviente? ¿No es más creíble que en unos no quedará ningún viable, en muchos 1, en otros 2, 3 y quizás en los menos 5 ó 6? Los modelos que no consideran la variabilidad microbiana predicen con precisión la tasa de crecimiento pero han fracasado en la predicción de la fase de latencia...

Manipulação gênica do protozoário Neospora caninum como ferramenta para o estudo das interações parasito-hospedeiro

Neospora caninum is an obligate intracellular parasite classified in the phylum Apicomplexa, characterized by the presence of the apical complex composed by micronemes proteins, rhoptries and dense granules, used by parasite during the adhesion and invasion process of the host cell. This is the mean event in infection pathogenesis generated by N. caninum and other parasites from the phylum Apicomplexa, promoting influence in the parasite biology and the interface between the parasite and its host. Therefore, molecular tools have been developed in order to identify and characterize these possible virulence factors. Thus, the present study sought to establish a specific system of genetic manipulation of N. caninum, searching for the improvement of the genetics manipulation of this parasite. So, we developed genetically depleted N. caninum to Rop9 rhoptry using the pU6-Universal CRISPR-Cas9 plasmid of T. gondii modified by the insertion of Ku80. The Rop9 depleted parasite showed important during initial phase of invasion and replication of the parasite, however it was not characterized as a potential virulence fator for N. caninum. Furthermore, T. gondii proteins were expressed in N. caninum by the use of specific vectors for this parasite, showing an heterologous system for the study of Toxoplasma proteins, due to the fact that Gra15 or Gra24 of type II T. gondii and Rop16 of type I T. gondii were expressed in N. caninum tachyzoites in a stable way and keept its biological phenotype, as already presented the former parasite, that naturaly expresses these proteins. In addition, it was observed that N. caninum induced an inflammasome activation through NLRP3, ASC and Caspase-1. IL-1R/MyD88 demonstrated an indirect pathway in the control of parasite replication. Furthermore, it was observed that this activation is dependent of the potassium efflux and that different strains of N. caninum keep this activation profile. However, T. gondii strains block this activation, making necessary a prior signal in order to active the inflamosome pathway. Type I T. gondii Rop16 was identified as responsible for blocking this activation, in a dependent way to the STAT3 activation. Therefore, the development of molecular tools and their application in N. caninum may prove to be useful to identify and characterize virulent factors involved in the pathogenesis by these two protozoans.

Sistemas de cálculo, análise e operação virtual: interferências de campos elétricos e magnéticos produzidas por estações radio base de acesso múltiplo por divisão de código em banda larga - WCDMA

In this work it was developed mathematical resolutions taking as parameter maximum intensity values for the interference analysis of electric and magnetic fields and was given two virtual computer system that supports families of CDMA and WCDMA technologies. The first family were developed computational resources to solve electric and magnetic field calculations and power densities in Radio Base stations , with the use of CDMA technology in the 800 MHz band , taking into account the permissible values referenced by the Commission International Protection on non-Ionizing Radiation . The first family is divided into two segments of calculation carried out in virtual operation. In the first segment to compute the interference field radiated by the base station with input information such as radio channel power; Gain antenna; Radio channel number; Operating frequency; Losses in the cable; Attenuation of direction; Minimum Distance; Reflections. Said computing system allows to quickly and without the need of implementing instruments for measurements, meet the following calculated values: Effective Radiated Power; Sector Power Density; Electric field in the sector; Magnetic field in the sector; Magnetic flux density; point of maximum permissible exposure of electric field and power density. The results are shown in charts for clarity of view of power density in the industry, as well as the coverage area definition. The computer module also includes folders specifications antennas, cables and towers used in cellular telephony, the following manufacturers: RFS World, Andrew, Karthein and BRASILSAT. Many are presented "links" network access "Internet" to supplement the cable specifications, antennas, etc. . In the second segment of the first family work with more variables , seeking to perform calculations quickly and safely assisting in obtaining results of radio signal loss produced by ERB . This module displays screens representing propagation systems denominated "A" and "B". By propagating "A" are obtained radio signal attenuation calculations in areas of urban models , dense urban , suburban , and rural open . In reflection calculations are present the reflection coefficients , the standing wave ratio , return loss , the reflected power ratio , as well as the loss of the signal by mismatch impedance. With the spread " B" seek radio signal losses in the survey line and not targeted , the effective area , the power density , the received power , the coverage radius , the conversion levels and the gain conversion systems radiant . The second family of virtual computing system consists of 7 modules of which 5 are geared towards the design of WCDMA and 2 technology for calculation of telephone traffic serving CDMA and WCDMA . It includes a portfolio of radiant systems used on the site. In the virtual operation of the module 1 is compute-: distance frequency reuse, channel capacity with noise and without noise, Doppler frequency, modulation rate and channel efficiency; Module 2 includes computes the cell area, thermal noise, noise power (dB), noise figure, signal to noise ratio, bit of power (dBm); with the module 3 reaches the calculation: breakpoint, processing gain (dB) loss in the space of BTS, noise power (w), chip period and frequency reuse factor. Module 4 scales effective radiated power, sectorization gain, voice activity and load effect. The module 5 performs the calculation processing gain (Hz / bps) bit time, bit energy (Ws). Module 6 deals with the telephone traffic and scales 1: traffic volume, occupancy intensity, average time of occupancy, traffic intensity, calls completed, congestion. Module 7 deals with two telephone traffic and allows calculating call completion and not completed in HMM. Tests were performed on the mobile network performance field for the calculation of data relating to: CINP , CPI , RSRP , RSRQ , EARFCN , Drop Call , Block Call , Pilot , Data Bler , RSCP , Short Call, Long Call and Data Call ; ECIO - Short Call and Long Call , Data Call Troughput . As survey were conducted surveys of electric and magnetic field in an ERB , trying to observe the degree of exposure to non-ionizing radiation they are exposed to the general public and occupational element. The results were compared to permissible values for health endorsed by the ICNIRP and the CENELEC .

Implementação LEAN: padronização e auditorias numa linha de pintura industrial

O presente relatório centra-se na aplicação de um sistema de padronização numa célula de pintura industrial. Assim, e como a célula estudada não tinha no momento um sistema de padronização implementado, a principal motivação deste trabalho prendeu-se com a obtenção de benefícios que a normalização de boas práticas pode trazer aos processos, principalmente em indústrias extremamente competitivas, como é o caso do setor em que a empresa em estudo se insere. Para sustentar a implementação da padronização na célula de pintura foi primariamente realizado um estudo teórico sobre a metodologia de base: o LEAN, assim como sobre algumas das suas principais ferramentas. Em particular, destaca-se o Standard Work, ou Padronização, e a Auditoria. Fazendo uso deste levantamento bibliográfico e dos recursos presentes na empresa de acolhimento, foi assim gerado e implementado um sistema padronizado na célula de pintura, composto essencialmente por padrões de tarefas e documentação. Estes têm como principal função criar fundações de base fiável e íntegra, servindo de apoio ao controlo da qualidade, resolução de problemas, e implementação de melhorias no futuro industrial da célula visada. De modo complementar, foi também produzido um conjunto de propostas de implementações de novos métodos, incidindo principalmente na melhoria da qualidade de execução das operações de setup.

Relatório de estágio no The Vintage House Lisboa Hotel

O presente relatório refere-se a um estágio curricular realizado no âmbito do Mestrado em Gestão e Direção Hoteleira. O estágio decorreu no hotel The Vintage House Lisboa, com inicio a 18 de agosto de 2014 e término a 31 de maio de 2015, consistindo num cross-training pelos departamentos: Housekeeping, F&B, Front-Office, “Célula”, Economato e Direção. O principal objetivo deste relatório é descrever as tarefas realizadas ao longo do estágio, bem como as competências adquiridas, as contribuições dadas a cada departamento, e sugestões de melhoria; que juntamente com a caracterização do hotel possibilitam um melhor entendimento de todo o trabalho. Foi através da observação e participação nas várias funções da unidade hoteleira que foi possível realizar uma intensa análise para, posteriormente, descrever os vários departamentos e, por fim, propor a melhoria da análise da satisfação dos clientes do hotel. A análise à satisfação do cliente é realizada através de três questionários, cada um dirigido a um público diferente: clientes externos dos outlets de F&B, clientes MICE, e hóspedes. Através desta análise, a unidade hoteleira poderá obter bastantes vantagens como o acréscimo da qualidade do serviço, o aumento da satisfação dos seus clientes, e a sua retenção e lealdade. Ao terminar este relatório, constatou-se a forte importância que o conhecimento das necessidades, perceções e expectativas dos clientes tem para o desenvolvimento e distinção de uma empresa ou unidade hoteleira; traduzindo-se numa extrema necessidade de uma continua adaptação às transformações do sector hoteleiro e dos seus consumidores, para conseguir um maior destacamento da feroz concorrência.

Avaliação experimental do comportamento dinâmico de paredes de alvenaria de tijolo térmico

Compete aos agentes que concebem os edifícios, bem como aos legisladores e aos promotores, dotá-los com o máximo possível de tecnologias passivas que permitam ao utilizador economizar, sem no entanto perder conforto nem salubridade. O presente estudo consiste num trabalho de revisão bibliográfica e de investigação experimental com vista à avaliação do comportamento dinâmico de paredes de alvenaria de tijolo térmico. Aferiu-se o desempenho térmico deste tipo de paredes e a viabilidade da sua utilização essencialmente numa perspetiva da redução dos consumos energéticos e de garantia do conforto térmico e salubridade nos edifícios. Os tijolos térmicos estão cada vez mais a ser introduzidos na construção devido ainda à simplicidade na construção e a possível eliminação/redução do material isolante. Neste trabalho construiu-se uma célula de teste com paredes constituídas por este tipo de tijolo, o Bloco ThermoPrélis, cedido pela empresa PRELIS Lda. Assim, mediu-se o desempenho térmico do mesmo em condições reais, em períodos nas estações de primavera e do verão. Os resultados experimentais mostram claramente as vantagens da construção com este tipo de tijolo, que apresenta um atraso térmico de 7 a 8 horas e um amortecimento da amplitude térmica no ambiente interior bastante significativo, tirando partido do mecanismo físico associado à inércia térmica. Em termos de custos, a construção com tijolo térmico apresenta vantagens, quando comparado com a construção típica em parede dupla com isolamento térmico na caixa-de-ar.

El Congreso por la Libertad de la Cultura y su apoyo a la disidencia intelectual durante el franquismo

El artículo reconstruye los principales aspectos de la labor del Congreso por la Libertad de la Cultura entre la oposición antifranquista del interior. Se describen las circunstancias políticas que motivaron la fundación del Comité Español (1959-1977), así como las principales características de esa célula intelectual antifranquista. El artículo indaga en los objetivos ideológicos y políticos de la actividad del Congreso por la Libertad de la Cultura entre las elites intelectuales y culturales disidentes durante el tardofranquismo. Nos concentramos especialmente en el capítulo que atañe a la ayuda directa dispensada por el Congreso por la Libertad de la Cultura a los intelectuales y artistas españoles mediante la concesión de becas de libros y bolsas de viaje a través del Comité d’Ecrivains et d’Editeurs pour une Entraide Européenne. Reconstruimos asimismo los nombres de los principales beneficiarios españoles de esas ayudas, así como la principal problemática vinculada al desarrollo del programa. El análisis histórico se apoya en documentos procedentes de diversos archivos nacionales e internacionales.

Melhoria de fluxos no armazém de componentes da Bosch Termotecnologia S.A.

A gestão de um armazém de componentes de uma qualquer empresa produtiva é uma das principais tarefas a desempenhar no seio desta, pois a mesma afecta toda a cadeia de abastecimento de entrega do produto final, sendo o armazém de componentes o início da cadeia interna. Qualquer dificuldade que surja no desenrolar das actividades associadas poderá causar impactos prejudiciais nos processos consequentes. A melhoria do principal processo do armazém, correspondente à satisfação dos pedidos de material dos processos a jusante, é algo que trará benefícios a toda a cadeia, ao mesmo tempo que são melhoradas as condições de trabalho, eliminando o desperdício e tornando o processo mais eficiente. Não obstante deste processo, ainda existe a necessidade de recolher e gerir informações referentes aos diferentes processos do armazém da maneira mais rápida possível, para actuar de acordo com as necessidades. A falta de informação relativamente ao estado de um processo também poderá influenciar os processos seguintes de forma negativa. O projecto aqui apresentado foi realizado no armazém de componentes da Bosch Termotecnologia S.A., em Aveiro, tendo como objectivo mostrar a importância da movimentação de material e também de informação dentro desta área, criando ao mesmo tempo a melhoria tanto dos fluxos de material como dos fluxos de informação. Serão apresentadas diferentes implementações que foram desenvolvidas com o intuito de criar melhoria nos fluxos: a criação de novos fluxos de informação para o processo de recepção de material, com o intuito de recolher informação que até agora não era perceptível, para depois actuar na melhoria do processo; a criação de áreas dedicadas dentro da área de picking, de modo a atingir uma redução no número de colaboradores afectos ao processo de picking; a implementação de uma célula de repacking, de modo a remover esta actividade do processo de picking; bem como todas as actividades realizadas com o objectivo de implementar as melhorias propostas.

Development and characterization of Poly(L-lactic acid) (PLLA) platforms for bone tissue engineering

The development of scaffolds based on biomaterials is a promising strategy for Tissue Engineering and cellular regeneration. This work focuses on Bone Tissue Engineering, the aim is to develop electrically tailored biomaterials with different crystalline and electric features, and study their impacts onto cell biological behavior, so as to predict the materials output in the enhancement of bone tissue regeneration. It is accepted that bone exhibits piezoelectricity, a property that has been proved to be involved in bone growth/repair mechanism regulation. In addition electrical stimulations have been proved to influence bone growth and repair. Piezoelectric materials are therefore widely investigated for a potential use in bone tissue engineering. The main goal is the development of novel strategies to produce and employ piezoelectric biomaterials, with detailed knowledge of mechanisms involved in cell-material interaction. In the current work, poly (L-lactic) acid (PLLA), a synthetic semi-crystalline polymer, exhibiting biodegradibility, biocompatibility and piezoelectricity is studied and proposed as a promoter of enhanced tissue regeneration. PLLA has already been approved for implantation in human body by the Food and Drug Administration (FDA), and at the moment it is being used in several clinical strategies. The present study consists of first preparing films with different degrees of crystallinity and characterizing these PLLA films, in terms of surface and structural properties, and subsequently assessing the behavior of cells in terms of viability, proliferation, morphology and mineralization for each PLLA configuration. PLLA films were prepared using the solvent cast technique and submitted to different thermal treatments in order to obtain different degrees of crystallinity. Those platforms were then electrically poled, positively and negatively, by corona discharge in order to tailor their electrical properties. The cellular assays were conducted by using two different osteoblast cell lines grown directly onto the PLLA films:Human osteoblast Hob, a primary cell culture and Human osteosarcoma MG-63 cell line. This thesis gives also a comprehensive introduction to the area of Bone Tissue Engineering and provides a review of the work done in this field in the past until today, in that same field, including the one related with bone’s piezoelectricity. Then the experimental part deals with the effects of the crystallinity degrees and of the polarization in terms of surface properties and cellular bio assays. Three different degrees of crystallinity, and three different polarization conditions were prepared; which results in 9 different configurations under investigation.

Dispositivo automático de pesada diseñado para medir la evaporación desde el suelo

Este dispositivo mide la evaporación del suelo humedecido mediante un emisor de riego localizado. Consiste en dos depósitos cilíndricos, concéntricos. El depósito exterior (1) contiene una célula de carga (3) que soporta al depósito interior (2) y permite medir la evaporación mediante diferencias de pesada. El depósito interior contiene el suelo (2a) y un espacio inferior (2b) en el que se recoge el agua de drenaje. El diámetro del depósito interior se diseña con el objetivo de contener toda la superficie humedecida por el emisor y su profundidad no es muy elevada, ya que la evaporación se produce desde la superficie del suelo. La toma de datos se realiza de modo automático mediante un registrador de datos o sistema de adquisición de datos.

Optimization of Li-ion solid electrolytes

The synthesis and optimization of two Li-ion solid electrolytes were studied in this work. Different combinations of precursors were used to prepare La0.5Li0.5TiO3 via mechanosynthesis. Despite the ability to form a perovskite phase by the mechanochemical reaction it was not possible to obtain a pure La0.5Li0.5TiO3 phase by this process. Of all the seven combinations of precursors and conditions tested, the one where La2O3, Li2CO3 and TiO2 were milled for 480min (LaOLiCO-480) showed the best results, with trace impurity phases still being observed. The main impurity phase was that of La2O3 after mechanosynthesis (22.84%) and Li2TiO3 after calcination (4.20%). Two different sol-gel methods were used to substitute boron on the Zr-site of Li1+xZr2-xBx(PO4)3 or the P-site of Li1+6xZr2(P1-xBxO4)3, with the doping being achieved on the Zr-site using a method adapted from Alamo et al (1989). The results show that the Zr-site is the preferential mechanism for B doping of LiZr2(PO4)3 and not the P-site. Rietveld refinement of the unit-cell parameters was performed and it was verified by consideration of Vegard’s law that it is possible to obtain phase purity up to x = 0.05. This corresponds with the phases present in the XRD data, that showed the additional presence of the low temperature (monoclinic) phase for the powder sintered at 1200ºC for 12h of compositions with x ≥ 0.075. The compositions inside the solid solution undergo the phase transition from triclinic (PDF#01-074-2562) to rhombohedral (PDF#01-070-6734) when heating from 25 to 100ºC, as reported in the literature for the base composition. Despite several efforts, it was not possible to obtain dense pellets and with physical integrity after sintering, requiring further work in order to obtain dense pellets for the electrochemical characterisation of Li Zr2(PO4)3 and Li1.05Zr1.95B0.05(PO4)3.