EFFECT OF INTERMITTENT FRYING ON FATTY ACIDS, VITAMIN E, LIPID OXIDATION AND ACRYLAMIDE IN OILS AND PLANTAIN CHIPS COLLECTED FROM SMALL- SCALE PRODUCERS IN CAMEROON

Deep-fat frying is susceptible to induce the formation of undesirable products as lipid oxidation products and acrylamide in fried foods. Plantain chips produced by small-scale producers are sold to consumers without any control. The objective of this study was to evaluate the quality of plantain chips from local producers in relation to production process parameters and oils, and to identify the limiting factors for the production of acrylamide in plantain chips. Samples of frying oils and plantain chips prepared with either palm olein or soybean oil were collected from 10 producers in Yaoundé. Quality parameters determined in this study were: fatty acid composition of the oils, determined by gas chromatography (GC) of free acid methyl ester; trans fatty acids, determined by Fourier transform infra-red spectroscopy; Tocopherols and tocotrienols as markers of nutritional quality were analyzed by High Performance Liquid Chromatography in isocratic mode. Free fatty acids and acylglycerols as markers of lipid hydrolysis were analyzed by GC of trimethylsilyl derivatives of glycerides. Conjugated dienes, Anisidine value and viscosity as markers of lipid oxidation and thermal decomposition of the oils; acrylamide which is formed through Maillard reaction and identified as a toxic compound in various fried products. Asparagine content of the raw fresh plantain powder was also determined. Fatty acid composition of palm oleins was stable within a day of intermittent frying. In soybean oils, about 57% and 62.5% of linoleic and linolenic acids were lost but trans fatty acids were not detected. Soybean oils were partly hydrolysed leading to the formation of free fatty acids, monoacylglycerols and diacylglycerols. In both oils, tocopherols and tocotrienols contents decreased significantly by about 50%. Anisidine value (AV) and polymers contents increased slightly in fried palm oleins while conjugated hydroperoxides, AV and polymers greatly increased in soybean oils. Acrylamide was not detected in the chips. This is explained by the absence of asparagine in the raw plantains, the other acrylamide precursors being present. This study shows that the plantain chips prepared at the small-scale level in Yaounde with palm olein are of good quality regarding oxidation and hydrolysis parameters and the absence of acrylamide. In contrast, oxidation developed with soybean oil whose usage for frying should be questioned. Considering that asparagine is the limiting factor for the formation of acrylamide in plantain chips, its content depending on several factors such as production parameters and maturity stage should be explored.

Implementation and Operation of Collaborative Manufacturing Networks

Part 6: Engineering and Implementation of Collaborative Networks

Building an Ontology of Product/Service-Systems: Using a Maritime Case Study to Elicit Classifications and Characteristics

Part 4: Transition Towards Product-Service Systems

Avaliação fiscal vs valores de mercado de imóveis em dação em pagamento (segmento habitacional)

Mestrado em Gestão e Avaliação Imobiliária

Population ageing and monetary policy

Mestrado em Economia Monetária e Financeira

Size anomalies in EU bank stock returns

Mestrado em Finanças

Impact of potassium and phosphorus in biomass on the properties of fast Pyrolysis bio-oil

This study investigates fast pyrolysis bio-oils produced from alkali-metal-impregnated biomass (beech wood). The impregnation aim is to study the catalytic cracking of the pyrolysis vapors as a result of potassium or phosphorus. It is recognized that potassium and phosphorus in biomass can have a major impact on the thermal conversion processes. When biomass is pyrolyzed in the presence of alkali metal cations, catalytic cracking of the pyrolysis liquids occurs in the vapor phase, reducing the organic liquids produced and increasing yields of water, char, and gas, resulting in a bio-oil that has a lower calorific value and an increased chance of phase separation. Beech wood was impregnated with potassium or phosphorus (K impregnation and P impregnation, respectively) in the range of 0.10-2.00 wt %. Analytical pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS) was used to examine the pyrolysis products during thermal degradation, and thermogravimetric analysis (TGA) was used to examine the distribution of char and volatiles. Both potassium and phosphorus are seen to catalyze the pyrolytic decomposition of biomass and modify the yields of products. 3-Furaldehyde and levoglucosenone become more dominant products upon P impregnation, pointing to rearrangement and dehydration routes during the pyrolysis process. Potassium has a significant influence on cellulose and hemicellulose decomposition, not just on the formation of levoglucosan but also other species, such as 2(5H)-furanone or hydroxymethyl-cyclopentene derivatives. Fast pyrolysis processing has also been undertaken using a laboratory-scale continuously fed bubbling fluidized-bed reactor with a nominal capacity of 1 kg h-1 at the reaction temperature of 525 °C. An increase in the viscosity of the bio-oil during the stability assessment tests was observed with an increasing percentage of impregnation for both additives. This is because bio-oil undergoes polymerization while placed in storage as a result of the inorganic content. The majority of inorganics are concentrated in the char, but small amounts are entrained in the pyrolysis vapors and, therefore, end up in the bio-oil.

Acceptance of smartphone-based mobile shopping:mobile benefits, customer characteristics, perceived risk and the impact of application context

Despite their generally increasing use, the adoption of mobile shopping applications often differs across purchase contexts. In order to advance our understanding of smartphone-based mobile shopping acceptance, this study integrates and extends existing approaches from technology acceptance literature by examining two previously underexplored aspects. Firstly, the study examines the impact of different mobile and personal benefits (instant connectivity, contextual value and hedonic motivation), customer characteristics (habit) and risk facets (financial, performance, and security risk) as antecedents of mobile shopping acceptance. Secondly, it is assumed that several acceptance drivers differ in relevance subject to the perception of three mobile shopping characteristics (location sensitivity, time criticality, and extent of control), while other drivers are assumed to matter independent of the context. Based on a dataset of 410 smartphone shoppers, empirical results demonstrate that several acceptance predictors are associated with ease of use and usefulness, which in turn affect intentional and behavioral outcomes. Furthermore, the extent to which risks and benefits impact ease of use and usefulness is influenced by the three contextual characteristics. From a managerial perspective, results show which factors to consider in the development of mobile shopping applications and in which different application contexts they matter.

Characterization of MSW rejected fractions to fulfill RDF requirements and utilization

In order to fulfil European and Portuguese legal requirements, adequate alternatives to traditional municipal waste landfilling must be found namely concerning organic wastes and others susceptible of valorisation. According to the Portuguese Standard NP 4486:2008, refuse derived fuels (RDF) classification is based on three main parameters: lower heating value (considered as an economic parameter), chlorine content (considered as a technical parameter) and mercury content (considered as an environmental parameter). The purpose of this study was to characterize the rejected streams resulting from the mechanical treatment of unsorted municipal solid waste, from the plastic municipal selective collection and from the composting process, in order to evaluate their potential as RDF. To accomplish this purpose six sampling campaigns were performed. Chemical characterization comprised the proximate analysis – moisture content, volatile matter, ashes and fixed carbon, as well as trace elements. Physical characterization was also done. To evaluate their potential as RDF, the following parameters established in the Portuguese standard were also evaluated: heating value and chlorine content. As expected, results show that the refused stream from mechanical treatment is rather different from the selective collection rejected stream and from the rejected from the compost screening in terms of moisture, energetic matter and ashes, as well as heating value and chlorine. Preliminary data allows us to conclude that studied materials have a very interesting potential to be used as RDF. In fact, the rejected from selective collection and the one from composting have a heating value not very different from coal. Therefore, an important key factor may be the blending of these materials with others of higher heating values, after pre-processing, in order to get fuel pellets with good consistency, storage and handling characteristics and, therefore, combustion behavior.

Maltodextrin-incorporated-vacuum-dried honey powder: processing and stability

Honey is rich in sugar content and dominated by fructose and glucose that make honey prone to crystallize during storage. Due to honey composition, the anhydrous glass transition temperature of honey is very low that makes honey difficult to dry alone and drying aid or filler is needed to dry honey. Maltodextrin is a common drying aid material used in drying of sugar-rich food. The present study aims to study the processing of honey powder by vacuum drying method and the impact of drying process and formulation on the stability of honey powder. To achieve the objectives, the series of experiments were done: investigating of maltodextrin DE 10 properties, studying the effect of drying temperature, total solid concentration, DE value, maltodextrin concentration and anti-caking agent on honey powder processing and stability. Maltodextrin provide stable glass compared to lower molecular weight sugars. Dynamic Dew Point Isotherm (DDI) data could be used to determine amorphous content of a system. The area under the first derivative curve from DDI curve is equal to the amount of water needed by amorphous material to crystallize. The drying temperature affected the amorphous content of vacuum-dried honey powder. The higher temperature seemed to result in honey powder with more amorphous component. The ratio of maltodextrin affected more significantly the stability of honey powder compared to the treatments of total solids concentration, DE value and drying temperature. The critical water activity of honey powder was lower than water activity of the equilibrium water content corresponding to BET monolayer water content. Addition of anti-caking agent increased stability and flow-ability of honey powder. Addition of Calcium stearate could inhibit collapse of the honey powder during storage.

Hospital without dyspnea: Rationale and design of a multidisciplinary intervention

Dyspnea is a common and disabling symptom of respiratory and heart diseases, which is growing in incidence. During hospital admission, breathlessness is under-diagnosed and under-treated, although there are treatments available for controlling the symptom. We have developed a tailored implementation strategy directed to medical staff to promote the application of these pharmacological and non-pharmacological tools in dealing with dyspnea. The primary aim is to decrease the rate of patients that do not receive an adequate relief of dyspnea. This is a four-stage quasi-experimental study. The intervention consists in two teaching talks that will be taught in Cardiology and Respiratory Medicine Departments. The contents will be prepared by Palliative Care specialists, based on available tools for management of dyspnea and patients' needs. A cross-sectional study of dyspnea in hospitalized patients will be performed before and after the intervention to ascertain an improvement in dyspnea intensity due to changes in medical practices. The last phase consists in the creation of consensus protocols for dyspnea management based in our experience. The results of this study are expected to be of great value and may change clinical practice in the near future and promote a changing for the better of dyspnea care.

Experimental and modeling studies of forced convection storage and drying systems for sweet potatoes

Sweet potato is an important strategic agricultural crop grown in many countries around the world. The roots and aerial vine components of the crop are used for both human consumption and, to some extent as a cheap source of animal feed. In spite of its economic value and growing contribution to health and nutrition, harvested sweet potato roots and aerial vine components has limited shelf-life and is easily susceptible to post-harvest losses. Although post-harvest losses of both sweet potato roots and aerial vine components is significant, there is no information available that will support the design and development of appropriate storage and preservation systems. In this context, the present study was initiated to improve scientific knowledge about sweet potato post-harvest handling. Additionally, the study also seeks to develop a PV ventilated mud storehouse for storage of sweet potato roots under tropical conditions. In study one, airflow resistance of sweet potato aerial vine components was investigated. The influence of different operating parameters such as airflow rate, moisture content and bulk depth at different levels on airflow resistance was analyzed. All the operating parameters were observed to have significant (P < 0.01) effect on airflow resistance. Prediction models were developed and were found to adequately describe the experimental pressure drop data. In study two, the resistance of airflow through unwashed and clean sweet potato roots was investigated. The effect of sweet potato roots shape factor, surface roughness, orientation to airflow, and presence of soil fraction on airflow resistance was also assessed. The pressure drop through unwashed and clean sweet potato roots was observed to increase with higher airflow, bed depth, root grade composition, and presence of soil fraction. The physical properties of the roots were incorporated into a modified Ergun model and compared with a modified Shedd’s model. The modified Ergun model provided the best fit to the experimental data when compared with the modified Shedd’s model. In study three, the effect of sweet potato root size (medium and large), different air velocity and temperature on the cooling/or heating rate and time of individual sweet potato roots were investigated. Also, a simulation model which is based on the fundamental solution of the transient equations was proposed for estimating the cooling and heating time at the centre of sweet potato roots. The results showed that increasing air velocity during cooling and heating significantly (P < 0.05) affects the cooling and heating times. Furthermore, the cooling and heating times were significantly different (P < 0.05) among medium and large size sweet potato roots. Comparison of the simulation results with experimental data confirmed that the transient simulation model can be used to accurately estimate the cooling and heating times of whole sweet potato roots under forced convection conditions. In study four, the performance of charcoal evaporative cooling pad configurations for integration into sweet potato roots storage systems was investigated. The experiments were carried out at different levels of air velocity, water flow rates, and three pad configurations: single layer pad (SLP), double layers pad (DLP) and triple layers pad (TLP) made out of small and large size charcoal particles. The results showed that higher air velocity has tremendous effect on pressure drop. Increasing the water flow rate above the range tested had no practical benefits in terms of cooling. It was observed that DLP and TLD configurations with larger wet surface area for both types of pads provided high cooling efficiencies. In study five, CFD technique in the ANSYS Fluent software was used to simulate airflow distribution in a low-cost mud storehouse. By theoretically investigating different geometries of air inlet, plenum chamber, and outlet as well as its placement using ANSYS Fluent software, an acceptable geometry with uniform air distribution was selected and constructed. Experimental measurements validated the selected design. In study six, the performance of the developed PV ventilated system was investigated. Field measurements showed satisfactory results of the directly coupled PV ventilated system. Furthermore, the option of integrating a low-cost evaporative cooling system into the mud storage structure was also investigated. The results showed a reduction of ambient temperature inside the mud storehouse while relative humidity was enhanced. The ability of the developed storage system to provide and maintain airflow, temperature and relative humidity which are the key parameters for shelf-life extension of sweet potato roots highlight its ability to reduce post-harvest losses at the farmer level, particularly under tropical climate conditions.

Semi-pelagic Longline and Trammel Net Elasmobranch Catches in Southern Portugal: Catch Composition, Catch Rates and Discards

In Portugal, elasmobranch landings have decreased substantially in recent years. In this work, elasmobranch catches in semi-pelagic longlines (1997 and 1998) were compared with those in trammel nets (2000) in the Algarve, southern Portugal areas. In the semi-pelagic longline fi shery, 7 elasmobranch species represented 33.4% (2 185 specimens) of the total fi sh catches. Among the elasmobranch species, the most abundant were Galeus melastomus (63.3%), Etmopterus pusillus (21.7%) and Scyliorhinus canicula (14.2%). Most of these elasmobranchs were discarded (68.3% in total). In the trammel net fi shery, 16 different elasmobranch species represented 4.3% (597 specimens) of total fi sh catches and the most important species were Raja undulata (43.6%) and S. canicula (10.2%). The majority of the elasmobranchs caught in trammel nets had commercial value, and only 5.4% were discarded. In both fi sheries, intra-specifi c catch rates varied with depth. Length-frequency distributions for the only species with relatively high catches in both fi sheries, S. canicula, showed that, in general, trammel nets catch larger specimens and in a narrower length range than do longlines.

An investigation of the relationship between the components of tumour microenvironment, signal transduction pathways and outcome in breast cancer

Breast cancer, the most commonly diagnosed type of cancer in women, is a major cause of morbidity and mortality in the western world. Well-established risk factors of breast cancer are mostly related to women’s reproductive history, such as early menarche, late first pregnancy and late menopause. Survival rates have improved due to a combination of factors, including better health education, early detection with large-scale use of screening mammogram, improved surgical techniques, as well as widespread use of adjuvant therapy. At initial presentation, clinicopathological features of breast cancer such as age, nodal status, tumour size, tumour grade, and hormonal receptor status are considered to be the standard prognostic and predictive markers of patient survival, and are used to guide appropriate treatment strategies. Lymphovascular invasion (LBVI), including lymphatic (LVI) and blood (BVI) vessel invasion, has been reported to be prognostic and merit accurate evaluation, particularly in patients with node negative tumours who might benefit from adjuvant chemotherapy. There is a lack of standard assessment and agreement on distinguishing LVI from BVI despite the major challenges in the field. A systematic review of the literatures, examining methods of detection and the prognostic significance of LBVI, LVI and BVI, was carried out. The majority of studies used haematoxylin and eosin (H&E) and classical histochemistry to identify LVI and BVI. Only few recent studies used immunohistochemistry (IHC) staining of the endothelium lining lymphatic and blood vessels, and were able to show clear differences between LVI and BVI. The prognostic significance of LBVI and LVI was well-documented and strongly associated with aggressive features of breast tumours, while the prognostic value and the optimal detection method of BVI were unclear. Assessment and prognostic value of LBVI on H&E sections (LBVIH&E) was examined and compared to that of LVI and BVI detected using IHC with D2-40 for LVI (LVID2–40) and Factor VIII for BVI (BVIFVIII) in patients with breast cancer including node negative and triple negative patients (n=360). LBVIH&E, LVID2–40 and BVIFVIII were present in 102 (28%), 127 (35%) and 59 (16%) patients respectively. In node negative patients (206), LBVIH&E, LVID2–40 and BVIFVIII were present in 41 (20%), 53 (26%) and 21 (10%) respectively. In triple negative patients (102), LBVIH&E, LVID2–40 and BVIFVIII were present in 35 (29%), 36 (35%) and 14 (14%) respectively. LBVIH&E, LVID2–40 and BVIFVIII were all significantly associated with tumour recurrence in all cohorts. On multivariate survival analysis, only LVID2–40 and BVIFVIII were independent predictors of cancer specific survival (CSS) in the whole cohort (P=0.022 and P<0.001 respectively), node negative (P=0.008 and P=0.001 respectively) and triple negative patients (P=0.014 and P<0.001 respectively). Assessment of LVI and BVI by IHC, using D2-40 and Factor VIII, improves prediction of outcome in patients with node negative and triple negative breast cancer and was superior to the conventional detection method. Breast cancer is recognised as a complex molecular disease and histologically identical tumours may have highly variable outcomes, including different responses to therapy. Therefore, there is a compelling need for new prognostic and predictive markers helpful of selecting patients at risk and patients with aggressive diseases who might benefit from adjuvant and targeted therapy. It is increasingly recognised that the development and progression of human breast cancer is not only determined by genetically abnormal cells, but also dependent on complex interactions between malignant cells and the surrounding microenvironment. This has led to reconsider the features of tumour microenvironment as potential predictive and prognostic markers. Among these markers, tumour stroma percentage (TSP) and tumour budding, as well as local tumour inflammatory infiltrate have received recent attention. In particular, the local environment of cytokines, proteases, angiogenic and growth factors secreted by inflammatory cells and stromal fibroblasts has identified crucial roles in facilitating tumour growth, and metastasis of cancer cells through lymphatic and/or blood vessel invasion. This might help understand the underlying process promoting tumour invasion into these vessels. An increase in the proportion of tumour stroma and an increase in the dissociation of tumour cells have been associated with poorer survival in a number of solid tumours, including breast cancer. However, the interrelationship between these variables and other features of the tumour microenvironment in different subgroups of breast cancer are not clear. Also, whether their prognostic values are independent of other components of the tumour microenvironment have yet to be identified. Therefore, the relationship between TSP, clinicopathological characteristics and outcome in patients with invasive ductal breast cancer, in particular node negative and triple negative disease was examined in patients with invasive ductal breast cancer (n=361). The TSP was assessed on the haematoxylin and eosin-stained tissue sections. With a cut-off value of 50% TSP, patients with ≤50% stroma were classified as the low-TSP group and those with >50% stroma were classified as the high-TSP group. A total of 109 (30%) patients had high TSP. Patients with high TSP were old age (P=0.035), had involved lymph node (P=0.049), Her-2 positive tumours (P=0.029), low-grade peri-tumoural inflammatory infiltrate (P=0.034), low CD68+ macrophage infiltrate (P<0.001), low CD4+ (P=0.023) and low CD8+ T-lymphocytes infiltrate (P=0.017), tumour recurrence (P=0.015) and shorter CSS (P<0.001). In node negative patients (n=207), high TSP was associated with low CD68+ macrophage infiltrate (P=0.001), low CD4+ (P=0.040) and low CD8+ T-lymphocytes infiltrate (P=0.016) and shorter CSS (P=0.005). In triple negative patients (n=103), high TSP was associated with increased tumour size (P=0.017) high tumour grade (P=0.014), low CD8+ T-lymphocytes infiltrate (P=0.048) and shorter CSS (P=0.041). The 15-year cancer specific survival rate was 79% vs 21% in the low-TSP group vs high-TSP group. On multivariate survival analysis, a high TSP was associated with reduced CSS in the whole cohort (P=0.007), node negative patients (P=0.005) and those who received systemic adjuvant therapy (P=0.016), independent of other pathological characteristics including local host inflammatory responses. Therefore, a high TSP in invasive ductal breast cancer was associated with recurrence and poorer long-term survival. The inverse relation with the tumour inflammatory infiltrate highlights the importance of the amount of tumour stroma on immunological response in patients with invasive ductal breast cancer. Implementing this simple and reproducible parameter in routine pathological examination may help optimise risk stratification in patients with breast cancer. Similarly, the relationship between tumour budding, clinicopathological characteristics and outcome was examined in patients with invasive ductal breast cancer (n=474), using routine pathological sections. Tumour budding was associated with several adverse pathological characteristics, including positive lymph node (P=0.009), presence of LVI (P<0.001), and high TSP (P=0.001) and low-grade general peri-tumural inflammatory infiltrative (P=0.002). In node negative patients, a high tumour budding was associated with presence of LVI (P<0.001) and low-grade general peri-tumural inflammatory infiltrative (P=0.038). On multivariate survival analysis, tumour budding was associated with reduced CSS (P=0.001), independent of nodal status, tumour necrosis, CD8+ and CD138+ inflammatory cells infiltrate, LVI, BVI and TSP. Furthermore, tumour budding was independently associated with reduced CSS in node negative patients (P=0.004) and in those who have low TSP (P=0.003) and high-grade peri-tumoural inflammatory infiltrative (P=0.012). A high tumour budding was significantly associated with shorter CSS in luminal B and triple negative breast cancer subtypes (all P<0.001). Therefore, tumour budding was a significant predictor of poor survival in patients with invasive ductal breast cancer, independent of adverse pathological characteristics and components of tumour microenvironment. These results suggest that tumour budding may promote disease progression through a direct effect on local and distant invasion into lymph nodes and lymphatic vessels. Therefore, detection of tumour buds at the stroma invasive front might therefore represent a morphologic link between tumour progression, lymphatic invasion, spread of tumour cells to regional lymph nodes, and the establishment of metastatic dissemination. Given the potential importance of the tumour microenvironment, the characterisation of intracellular signalling pathways is important in the tumour microenvironment and is of considerable interest. One plausible signalling molecule that links tumour stroma, inflammatory cell infiltrate and tumour budding is the signal transducer and activator of transcription (STAT). The relationship between total and phosphorylated STAT1 (ph-STAT1), and total and ph-STAT3 tumour cell expression, components of tumour microenvironment and survival in patients with invasive ductal breast cancer was examined. IHC of total and ph-STAT1/STAT3 was performed on tissue microarray of 384 breast cancer specimens. Cellular STAT1 and cellular STAT3 expression at both cytoplasmic and nuclear locations were combined and identified as STAT1/STAT3 tumour cell expression. These results were then related to CSS and phenotypic features of the tumour and host. A high ph-STAT1 and a high ph-STAT3 tumour cell expression was associated with increased ER (P=0.001 and P<0.001 respectively) and PR (all P<0.05), reduced tumour grade (P=0.015 and P<0.001 respectively) and necrosis (all P=0.001). Ph-STAT1 was associated with increased general peri-tumoural inflammatory infiltrate (P=0.007) and ph-STAT3 was associated with lower CD4+ T-lymphocyte infiltrate (P=0.024). On multivariate survival analysis, including both ph-STAT1 and ph-STAT3 tumour cell expression, only high ph-STAT3 tumour cell expression was significantly associated with improved CSS (P=0.010) independent of other tumour and host-based factors. In patients with high necrosis grade, high ph-STAT3 tumour cell expression was independent predictor of improved CSS (P=0.021). Ph-STAT1 and ph-STAT3 were also significantly associated with improved cancer specific survival in luminal A and B subtypes. STAT1 and STAT3 tumour cell expression appeared to be an important determinant of favourable outcome in patients with invasive ductal breast cancer. The present results suggest that STATs may affect disease outcome through direct impact on tumour cells, and the surrounding microenvironment. The above observations of the present thesis point to the importance of the tumour microenvironment in promoting tumour budding, LVI and BVI. The observations from STATs work may suggest that an important driving mechanism for the above associations is the presence of tumour necrosis, probably secondary to hypoxia. Further work is needed to examine the interaction of other molecular pathways involved in the tumour microenvironment, such as HIF and NFkB in patients with invasive ductal breast cancer.

El capital intelectual y su relación con la innovación en la universidad CES

En la sociedad actual del conocimiento las universidades tienen la responsabilidad de generar conocimiento e innovaciones para ofrecer soluciones a problemas de comunidades de interés. Para lograrlo las universidades deben enfocarse en su activo más importante, su capital intelectual. Hasta ahora las investigaciones relacionadas con el capital intelectual y la innovación en las universidades, son limitadas a pesar de ser un elemento estratégico para la dirección de estas organizaciones, ya que estos aspectos le representan valor en el tiempo, por tanto esta investigación busca establecer cuál es la relación que existe entre el capital intelectual y la innovación en la Universidad CES. El objetivo de esta investigación era identificar el grado de relación entre capital intelectual e innovación en la Universidad CES. La metodología del estudio, es un estudio cuantitativo, de tipo descriptivo explicativo, con un diseño transversal, que permitió establecer el efecto del capital intelectual sobre la innovación de la Universidad CES. La población del fueron los directivos, líderes de los grupos de investigación y los coordinadores de investigación de la Universidad CES. Según los resultados obtenidos, este estudio determinó que el capital intelectual no tiene una relación estadísticamente significativa con la innovación personal de la Universidad CES y se determinó también que las tres dimensiones del capital intelectual tienen una relación estadísticamente significativa con los resultados de la innovación en la Universidad CES. El principal aporte de este estudio fue ofrecer evidencias sobre el capital intelectual como una de las principales fuentes de innovación para la Universidad.