Optimization of aeroponic technology for future integration in quality potato seed production systems in tropical environments

Virus and soil borne pathogens negatively impact on the production of potatoes in tropical highland and sub-tropical environments, limiting supply of an increasingly popular and important vegetable in these regions. It is common for latent disease infected seed tubers or field grown cuttings to be used as potato planting material. We utilised an International Potato Centre technique, using aeroponic technology, to produce low cost mini-tubers in tropical areas. The system has been optimised for increased effectiveness in tropical areas. High numbers of seed tubers of cultivar Sebago (630) and Nicola per m2 (>900) were obtained in the first generation, and the system is capable of producing five crops of standard cultivars in every two years. Initial results indicate that quality seed could be produced by nurseries and farmers, therefore contributing to the minimisation of soil borne diseases in an integrated management plan. This technology reduces seed production costs, benefiting seed and potato growers. © ISHS.

Use of short-term breath measures to estimate daily methane production by cattle

Methods to measure enteric methane (CH4) emissions from individual ruminants in their production environment are required to validate emission inventories and verify mitigation claims. Estimates of daily methane production (DMP) based on consolidated short-term emission measurements are developing, but method verification is required. Two cattle experiments were undertaken to test the hypothesis that DMP estimated by averaging multiple short-term breath measures of methane emission rate did not differ from DMP measured in respiration chambers (RC). Short-term emission rates were obtained from a GreenFeed Emissions Monitoring (GEM) unit, which measured emission rate while cattle consumed a dispensed supplement. In experiment 1 (Expt. 1), four non-lactating cattle (LW=518 kg) were adapted for 18 days then measured for six consecutive periods. Each period consisted of 2 days of ad libitum intake and GEM emission measurement followed by 1 day in the RC. A prototype GEM unit releasing water as an attractant (GEM water) was also evaluated in Expt. 1. Experiment 2 (Expt. 2) was a larger study based on similar design with 10 cattle (LW=365 kg), adapted for 21 days and GEM measurement was extended to 3 days in each of the six periods. In Expt. 1, there was no difference in DMP estimated by the GEM unit relative to the RC (209.7 v. 215.1 g CH4/day) and no difference between these methods in methane yield (MY, 22.7 v. 23.7 g CH4/kg of dry matter intake, DMI). In Expt. 2, the correlation between GEM and RC measures of DMP and MY were assessed using 95% confidence intervals, with no difference in DMP or MY between methods and high correlations between GEM and RC measures for DMP (r=0.85; 215 v. 198 g CH4/day SEM=3.0) and for MY (r=0.60; 23.8 v. 22.1 g CH4/kg DMI SEM=0.42). When data from both experiments was combined neither DMP nor MY differed between GEM- and RC-based measures (P>0.05). GEM water-based estimates of DMP and MY were lower than RC and GEM (P<0.05). Cattle accessed the GEM water unit with similar frequency to the GEM unit (2.8 v. 3.5 times/day, respectively) but eructation frequency was reduced from 1.31 times/min (GEM) to once every 2.6 min (GEM water). These studies confirm the hypothesis that DMP estimated by averaging multiple short-term breath measures of methane emission rate using GEM does not differ from measures of DMP obtained from RCs. Further, combining many short-term measures of methane production rate during supplement consumption provides an estimate of DMP, which can be usefully applied in estimating MY.

Effect of commercial starter cultures and native yeasts on ochratoxin a production by aspergillus westerdijkiae and penicillium nordicum in meat products

Processed meat products are of worldwide importance and, because of their intrinsic factors as well as the processing methods, they are highly prone to fungal and mycotoxin contamination. Ochratoxin A (OTA) is the most significant mycotoxin in processed meat products. Penicillium nordicum is considered to be responsible for OTA contamination of meat products, as it is highly adapted to salt and protein-rich matrices and is moderately psycrotrophic. However, another OTA-producing fungus, Aspergillus westerdijkiae, adapted to carbon-rich matrices such as cereals and coffee beans, has been recently associated with high levels of OTA in meat products. Several Lactic Acid Bacteria (LAB) and yeasts have been tested as biocontrol agents against P. nordicum growth and OTA production in meat products, with promising results, but none of the studies have considered A. westerdijkiae. The aim of this work was to evaluate in vitro the effect of a commercial starter culture used in sausage fermentation and four yeasts isolated from dry-cured sausage on these two OTA-producing fungi, both in terms of fungal growth and of OTA production, using different meat-based culture media as model systems. The mechanisms underlying the observed effect were also studied. For this purpose, C. krusei, C. zeylanoides, R. mucilaginosa, R. glutinis, a mix of these yeasts and the starter culture were co-inoculated with P. nordicum and A. westerdijkiae in industrial sausage, traditional sausage, and ham-based media, under conditions of water activity, salt concentration and temperature that mimic real conditions at beginning and end of sausage curing process. Fungal growth was determined by measuring colony diameter, and OTA production was quantified by HPLC-FLD after extraction with methanol. Yeasts where found to inhibit significantly the growth of both fungi. P. nordicum was unable to produce detectable OTA in both sausage-based media under any condition. In ham, yeasts reduced OTA production, while the starter culture significantly increased it. Unexpectedly, OTA production by A. westerdijkiae was significantly stimulated in all media tested by all microorganisms. Matrix has a significant effect on OTA production by P. nordicum, but not by A. westerdijkiae, for which only temperature showed to have effect. By testing the mechanisms of action by which starter culture and C. zeylanoides influenced fungal responses, we were able to determine that direct contact and simultaneous growth of test organisms were the mechanisms more significantly involved in the responses. In conclusion, ochratoxigenic fungi do not all respond to antagonistic microorganisms in the same way. The use of biocontrol agents with the intent of reducing fungal growth and mycotoxin production by one fungus can have unexpected effects on others, thus leading to unforeseen safety problems. Further experiments are recommended to properly understand the reasons behind the different effects of microorganisms, to ensure their safe as biocontrol agents.

Evaluation of ergonomic physical risk factors in a truck manufacturing plant: case study in SCANIA Production Angers

International audience

NITROUS OXIDE EMISSIONS IN COVER CROP-BASED CORN PRODUCTION SYSTEMS

Nitrous oxide (N2O) is a potent greenhouse gas; the majority of N2O emissions are the result of agricultural management, particularly the application of N fertilizers to soils. The relationship of N2O emissions to varying sources of N (manures, mineral fertilizers, and cover crops) has not been well-evaluated. Here we discussed a novel methodology for estimating precipitation-induced pulses of N2O using flux measurements; results indicated that short-term intensive time-series sampling methods can adequately describe the magnitude of these pulses. We also evaluated the annual N2O emissions from corn-cover crop (Zea mays; cereal rye [Secale cereale], hairy vetch [Vicia villosa], or biculture) production systems when fertilized with multiple rates of subsurface banded poultry litter, as compared with tillage incorporation or mineral fertilizer. N2O emissions increased exponentially with total N rate; tillage decreased emissions following cover crops with legume components, while the effect of mineral fertilizer was mixed across cover crops.

Increasing value add in white collar work using lean methods

The efficient indirect office work brings competitive advantage for companies in a rapidly changing business environment. The direct work methods in factory floors have been developed already for decades, but the office work is an area where the potential to improve the value add has not been studied and utilized systematically so far. The first objective of the thesis work is to find useful method for identifying and managing value add using literature. The usefulness of the method is validated in the case company`s environment. The second objective of the work is to understand what kind of effort is required to create more efficient target setting for the white collar employees. The operative level targets should be linked more tightly to the company strategy. Lean methods are selected as a tool for the improvement, since they are widely used in all kinds of industries and they are already familiar in other functions in the case company. Based on the literature review, suitable improvement methods are selected. The core of the lean is to identify the value add of a customer and eliminate the waste. Also visual control, cross functional work team, flow office and continuous improvement are used. The methods are tested in one production line and the results and feedback indicate that methods are useful in the studied environment.

Method of numerical correction of errors occasioned by delay of records during the monitoring of environmental variables of interest for animal production

As condições de ambiente térmico e aéreo, no interior de instalações para animais, alteram-se durante o dia, devido à influência do ambiente externo. Para que análises estatísticas e geoestatísticas sejam representativas, uma grande quantidade de pontos distribuídos espacialmente na área da instalação deve ser monitorada. Este trabalho propõe que a variação no tempo das variáveis ambientais de interesse para a produção animal, monitoradas no interior de instalações para animais, pode ser modelada com precisão a partir de registros discretos no tempo. O objetivo deste trabalho foi desenvolver um método numérico para corrigir as variações temporais dessas variáveis ambientais, transformando os dados para que tais observações independam do tempo gasto durante a aferição. O método proposto aproximou os valores registrados com retardos de tempo aos esperados no exato momento de interesse, caso os dados fossem medidos simultaneamente neste momento em todos os pontos distribuídos espacialmente. O modelo de correção numérica para variáveis ambientais foi validado para o parâmetro ambiental temperatura do ar, sendo que os valores corrigidos pelo método não diferiram pelo teste Tukey, a 5% de probabilidade dos valores reais registrados por meio de dataloggers.

Computationally-guided thermostabilization of the primary endoglucanase from Hypocrea jecorina for cellulosic biofuel production

The creation of thermostable enzymes has wide-ranging applications in industrial, scientific, and pharmaceutical settings. As various stabilization techniques exist, it is often unclear how to best proceed. To this end, we have redesigned Cel5A (HjCel5A) from Hypocrea jecorina (anamorph Trichoderma reesei) to comparatively evaluate several significantly divergent stabilization methods: 1) consensus design, 2) core repacking, 3) helix dipole stabilization, 4) FoldX ΔΔG approximations, 5) Triad ΔΔG approximations, and 6) entropy reduction through backbone stabilization. As several of these techniques require structural data, we initially solved the first crystal structure of HjCel5A to 2.05 Å. Results from the stabilization experiments demonstrate that consensus design works best at accurately predicting highly stabilizing and active mutations. FoldX and helix dipole stabilization, however, also performed well. Both methods rely on structural data and can reveal non-conserved, structure-dependent mutations with high fidelity. HjCel5A is a prime target for stabilization. Capable of cleaving cellulose strands from agricultural waste into fermentable sugars, this protein functions as the primary endoglucanase in an organism commonly used in the sustainable biofuels industry. Creating a long-lived, highly active thermostable HjCel5A would allow cellulose hydrolysis to proceed more efficiently, lowering production expenses. We employed information gleaned during the survey of stabilization techniques to generate HjCel5A variants demonstrating a 12-15 °C increase in the temperature at which 50% of the total activity persists, an 11-14 °C increase in optimal operating temperature, and a 60% increase over the maximal amount of hydrolysis achievable using the wild type enzyme. We anticipate that our comparative analysis of stabilization methods will prove useful in future thermostabilization experiments.

Improved production of chlorogenic acid from cell suspension cultures of Lonicera macranthoids

Purpose: To evaluate the potential of Lonicera macranthoids Hand. -Mazz. Yulei1 suspension culture system for enhanced production of the main secondary metabolite, chlorogenic acid. Methods: The callus of L. macranthoides Hand.-Mazz. “Yulei1” was suspension cultured in B5 liquid medium supplemented with different plant growth regulators. Biomass accumulation was calculated by weight method and chlorogenic acid production was measured using high performance liquid chromatography (HPLC). HPLC was carried out on C18 analytical column at 35 °C and the detection wavelength was set at 324 nm. Results: The results showed that maximum accumulation of biomass and chlorogenic acid were achieved 15 days after culture growth. The optimized conditions for biomass accumulation and chlorogenic acid production were 50 g/L of inoculum on fresh weight basis, B5 medium supplemented with plant growth regulators, 30 - 40 g/L sucrose and initial medium pH of 5.5. Maximum accumulation of chlorogenic acid and biomass were observed when the culture medium was supplemented with 2.0 mg/L6-BA. Optimal accumulation of chlorogenic acid was observed using combination of hormones 2.0 mg/L 6-Benzyladenine (BA) + 0.5 mg/L2, 4-Dichlorophenoxyacetic acid (2,4-D), while optimal accumulation of biomass was observed with 2.0 mg/L 6-BA + 2.0 mg/L2, 4-D. In addition, phenylalanine also contributed to the synthesis of chlorogenic acid at a concentration > 50 mg/L. Conclusion: Cell suspension cultures of L. macranthoides Hand.-Mazz. “Yulei1” have successfully been established. The findings provide a potential basis for large scale production of chlorogenic acid using cell suspension cultures of L. macranthoides.

CHARACTERIZING AND IMPROVING PRODUCTION OF FERMENTABLE SUGARS AND CO-PRODUCTS FROM A FOREST PRODUCT INDUSTRY WASTEWATER STREAM

Hardboard processing wastewater was evaluated as a feedstock in a bio refinery co-located with the hardboard facility for the production of fuel grade ethanol. A thorough characterization was conducted on the wastewater and the composition changes of which during the process in the bio refinery were tracked. It was determined that the wastewater had a low solid content (1.4%), and hemicellulose was the main component in the solid, accounting for up to 70%. Acid pretreatment alone can hydrolyze the majority of the hemicellulose as well as oligomers, and over 50% of the monomer sugars generated were xylose. The percentage of lignin remained in the liquid increased after acid pretreatment. The characterization results showed that hardboard processing wastewater is a feasible feedstock for the production of ethanol. The optimum conditions to hydrolyze hemicellulose into fermentable sugars were evaluated with a two-stage experiment, which includes acid pretreatment and enzymatic hydrolysis. The experimental data were fitted into second order regression models and Response Surface Methodology (RSM) was employed. The results of the experiment showed that for this type of feedstock enzymatic hydrolysis is not that necessary. In order to reach a comparatively high total sugar concentration (over 45g/l) and low furfural concentration (less than 0.5g/l), the optimum conditions were reached when acid concentration was between 1.41 to 1.81%, and reaction time was 48 to 76 minutes. The two products produced from the bio refinery were compared with traditional products, petroleum gasoline and traditional potassium acetate, in the perspective of sustainability, with greenhouse gas (GHG) emission as an indicator. Three allocation methods, system expansion, mass allocation and market value allocation methods were employed in this assessment. It was determined that the life cycle GHG emissions of ethanol were -27.1, 20.8 and 16 g CO2 eq/MJ, respectively, in the three allocation methods, whereas that of petroleum gasoline is 90 g CO2 eq/MJ. The life cycle GHG emissions of potassium acetate in mass allocation and market value allocation method were 555.7 and 716.0 g CO2 eq/kg, whereas that of traditional potassium acetate is 1020 g CO2/kg.

Manufacturing methods for liposome adjuvants

A wide range of studies have shown that liposomes can act as suitable adjuvants for a range of vaccine antigens. Properties such as their amphiphilic character and biphasic nature allow them to incorporate antigens within the lipid bilayer, on the surface, or encapsulated within the inner core. However, appropriate methods for the manufacture of liposomes are limited and this has resulted in issues with cost, supply, and wider scale application of these systems. Within this chapter we explore manufacturing processes that can be used for the production of liposomal adjuvants, and we outline new manufacturing methods can that offer fast, scalable, and cost-effective production of liposomal adjuvants.

Detection of Carbapenemase Production in a Collection of Enterobacteriaceae with Characterized Resistance Mechanisms from Clinical and Environmental Origins by Use of Both Carba NP and Blue-Carba Tests

Rapid-screening methods to confirm the presence of resistance mechanisms in multidrug-resistant bacteria are currently recommended. Carba NP and Blue-Carba tests were evaluated in carbapenemase-producing Enterobacteriaceae from hospital (n = 102) and environmental (n = 57) origins for detecting the different molecular classes among them. Both methods showed to be fast and cost-effective, with high sensitivity (98% to 100%) and specificity (100%), and may be easily introduced in the routine laboratory.

Design and application of experimental methods for steel sheet shearing

Shearing is the process where sheet metal is mechanically cut between two tools. Various shearing technologies are commonly used in the sheet metal industry, for example, in cut to length lines, slitting lines, end cropping etc. Shearing has speed and cost advantages over competing cutting methods like laser and plasma cutting, but involves large forces on the equipment and large strains in the sheet material. The constant development of sheet metals toward higher strength and formability leads to increased forces on the shearing equipment and tools. Shearing of new sheet materials imply new suitable shearing parameters. Investigations of the shearing parameters through live tests in the production are expensive and separate experiments are time consuming and requires specialized equipment. Studies involving a large number of parameters and coupled effects are therefore preferably performed by finite element based simulations. Accurate experimental data is still a prerequisite to validate such simulations. There is, however, a shortage of accurate experimental data to validate such simulations. In industrial shearing processes, measured forces are always larger than the actual forces acting on the sheet, due to friction losses. Shearing also generates a force that attempts to separate the two tools with changed shearing conditions through increased clearance between the tools as result. Tool clearance is also the most common shearing parameter to adjust, depending on material grade and sheet thickness, to moderate the required force and to control the final sheared edge geometry. In this work, an experimental procedure that provides a stable tool clearance together with accurate measurements of tool forces and tool displacements, was designed, built and evaluated. Important shearing parameters and demands on the experimental set-up were identified in a sensitivity analysis performed with finite element simulations under the assumption of plane strain. With respect to large tool clearance stability and accurate force measurements, a symmetric experiment with two simultaneous shears and internal balancing of forces attempting to separate the tools was constructed. Steel sheets of different strength levels were sheared using the above mentioned experimental set-up, with various tool clearances, sheet clamping and rake angles. Results showed that tool penetration before fracture decreased with increased material strength. When one side of the sheet was left unclamped and free to move, the required shearing force decreased but instead the force attempting to separate the two tools increased. Further, the maximum shearing force decreased and the rollover increased with increased tool clearance. Digital image correlation was applied to measure strains on the sheet surface. The obtained strain fields, together with a material model, were used to compute the stress state in the sheet. A comparison, up to crack initiation, of these experimental results with corresponding results from finite element simulations in three dimensions and at a plane strain approximation showed that effective strains on the surface are representative also for the bulk material. A simple model was successfully applied to calculate the tool forces in shearing with angled tools from forces measured with parallel tools. These results suggest that, with respect to tool forces, a plane strain approximation is valid also at angled tools, at least for small rake angles. In general terms, this study provide a stable symmetric experimental set-up with internal balancing of lateral forces, for accurate measurements of tool forces, tool displacements, and sheet deformations, to study the effects of important shearing parameters. The results give further insight to the strain and stress conditions at crack initiation during shearing, and can also be used to validate models of the shearing process.

De la lecture à la production verbale écrite, et réciproquement

L’objectif du chapitre consiste à dresser un bilan des acquis concernant les relations entre lecture-compréhension et écriture-rédaction. Deux approches sont envisagées. La première s’appuie sur des évaluations globales des dimensions relatives dites au bas niveau (au code : écriture et décodage) et des dimensions de haut niveau (compréhension et production textuelle). Elle met en évidence des relations fortes entre les premières, mais plutôt faibles entre les secondes. La seconde approche procède à la mise en relation entre composantes des deux activités : lexique (en lecture et en production), syntaxe, structure des textes, etc. Elle fait apparaître une plus grande complexité des relations et une relative indépendance des composantes. Elle conduit à reposer la question des impacts respectifs et réciproques de la lecture-compréhension sur l’écriture-rédaction. Elle amène à s’interroger sur ce que seraient les effets d’une pratique accordant une priorité à la production plutôt qu’à la lecture-compréhension et à rechercher les modalités d’intervention visant à améliorer l’une à partir de l’autre, et réciproquement.

Production de biodiesel à partir de microalgues par catalyses homogène et hétérogène

Résumé : Au Canada, près de 80% des émissions totales, soit 692 Mt eq. CO[indice inférieur 2], des gaz à effet de serre (GES) sont produits par les émissions de dioxyde de carbone (CO[indice inférieur 2]) provenant de l’utilisation de matières fossiles non renouvelables. Après la Conférence des Nations Unies sur les changements climatiques, COP21 (Paris, France), plusieurs pays ont pour objectif de réduire leurs émissions de GES. Dans cette optique, les microalgues pourraient être utilisées pour capter le CO[indice inférieur 2] industriel et le transformer en biomasse composée principalement de lipides, de glucides et de protéines. De plus, la culture des microalgues n’utilise pas de terre arable contrairement à plusieurs plantes oléagineuses destinées à la production de biocarburants. Bien que les microalgues puissent être transformées en plusieurs biocarburants tels le bioéthanol (notamment par fermentation des glucides) ou le biométhane (par digestion anaérobie), la transformation des lipides en biodiesel pourrait permettre de réduire la consommation de diesel produit à partir de pétrole. Cependant, les coûts reliés à la production de biodiesel à partir de microalgues demeurent élevés pour une commercialisation à court terme en partie parce que les microalgues sont cultivées en phase aqueuse contrairement à plusieurs plantes oléagineuses, ce qui augmente le coût de récolte de la biomasse et de l’extraction des lipides. Malgré le fait que plusieurs techniques de récupération des lipides des microalgues n’utilisant pas de solvant organique sont mentionnées dans la littérature scientifique, la plupart des méthodes testées en laboratoire utilisent généralement des solvants organiques. Les lipides extraits peuvent être transestérifiés en biodiesel en présence d’un alcool tel que le méthanol et d’un catalyseur (catalyses homogène ou hétérogène). Pour la commercialisation du biodiesel à partir de microalgues, le respect des normes ASTM en vigueur est un point essentiel. Lors des essais en laboratoire, il a été démontré que l’extraction des lipides en phase aqueuse était possible afin d’obtenir un rendement maximal en lipides de 36% (m/m, base sèche) en utilisant un prétraitement consistant en une ébullition de la phase aqueuse contenant les microalgues et une extraction par des solvants organiques. Pour l’estérification, en utilisant une résine échangeuse de cations (Amberlyst-15), une conversion des acides gras libres de 84% a été obtenue à partir des lipides de la microalgue Chlorella protothecoïdes dans les conditions suivantes : température : 120°C, pression autogène, temps de réaction : 60 min, ratio méthanol/lipides: 0.57 mL/g et 2.5% (m/m) Amberlyst-15 par rapport aux lipides. En utilisant ces conditions avec une catalyse homogène (acide sulfurique) et une seconde étape alcaline avec de l’hydroxyde de potassium (température : 60°C ; temps de réaction : 22.2 min; ratio catalyseur microalgue : 2.48% (m/m); ratio méthanol par rapport aux lipides des microalgues : 31.4%), un rendement en esters méthyliques d’acides gras (EMAG) de 33% (g EMAG/g lipides) a été obtenu à partir des lipides de la microalgue Scenedesmus Obliquus. Les résultats démontrent que du biodiesel peut être produit à partir de microalgues. Cependant, basé sur les présents résultats, il sera necessaire de mener d’autre recherche pour prouver que les microalgues sont une matière première d’avenir pour la production de biodiesel.