Emergence and development of a financial cluster: the evolution of Andorra’s banking deposits in the long-term, 1931-2007

This paper explores the origins of Andorra’s financial cluster. It shows that the free movement of currency, the protection of infant industry, and geographical concentration lie at the foundation of the cluster’s competitive advantage. Drawing on a new set of data, the paper also provides for the first time an estimate of the total deposits held by Andorra’s banks between 1931 and 2007. Based on this new information, the paper reaches the conclusion that the development of the cluster went through four distinct phases in which large companies, acting as leaders, played an important role in enhancing the cluster’s business capabilities.

Power line communication in motor cables of variable-speed electric drives − analysis and

Data transmission between an electric motor and a frequency converter is required in variablespeed electric drives because of sensors installed at the motor. Sensor information can be used for various useful applications to improve the system reliability and its properties. Traditionally, the communication medium is implemented by an additional cabling. However, the costs of the traditional method may be an obstacle to the wider application of data transmission between a motor and a frequency converter. In any case, a power cable is always installed between a motor and a frequency converter for power supply, and hence it may be applied as a communication medium for sensor level data. This thesis considers power line communication (PLC) in inverter-fed motor power cables. The motor cable is studied as a communication channel in the frequency band of 100 kHz−30 MHz. The communication channel and noise characteristics are described. All the individual components included in a variable-speed electric drive are presented in detail. A channel model is developed, and it is verified by measurements. A theoretical channel information capacity analysis is carried out to estimate the opportunities of a communication medium. Suitable communication and forward error correction (FEC) methods are suggested. A general method to implement a broadband and Ethernet-based communication medium between a motor and a frequency converter is proposed. A coupling interface is also developed that allows to install the communication device safely to a three-phase inverter-fed motor power cable. Practical tests are carried out, and the results are analyzed. Possible applications for the proposed method are presented. A speed feedback motor control application is verified in detail by simulations and laboratory tests because of restrictions for the delay in the feedback loop caused by PLC. Other possible applications are discussed at a more general level.

DFM/DFMA(A) – analysis and aspects of applying systematic engineering for a microwave testfixture design

In this paper, manufacturability analysis and collection of design aspects is made for a microwave test-fixture. Aspects of applying systematic design for a microwave test-fixture design and manufacturing are also analysed. Special questionnaires for the component and machining are made in order to enable necessary information to ensure DFM(A) – aspects of the component. The aspects of easy manufacturing for machining the microwave test-fixture are collected. Material selection is discussed and manufacturing stages of prototype manufacturing are presented.

Analytical challenges in breath analysis and its application to exposure monitoring

There is an increasing interest in the use of breath analysis for monitoring human physiology and exposure to toxic substances or environmental pollutants. This review focuses on the current status of the sampling procedures, collection devices and sample-enrichment methodologies used for exhaled breath-vapor analysis. We discuss the different parameters affecting each of the above steps, taking into account the requirements for breath analysis in exposure assessments and the need to analyze target compounds at sub-ppbv levels. Finally, we summarize the practical applications of exposure analysis in the past two decades

Electrocatalysis and electrocatalysts for low temperature fuel cells: fundamentals, state of the art, research and development

This article deals with electrocatalysis and electrocatalysts for low temperature fuel cells and also with established means and methods in electrocatalyst research, development and characterization. The intention is to inform about the fundamentals, state of the art, research and development of noble metal electrocatalysts for fuel cells operating at low temperatures.

Improving Evaluation and Development Capability in Verification and Validation

Validation and verification operations encounter various challenges in product development process. Requirements for increasing the development cycle pace set new requests for component development process. Verification and validation usually represent the largest activities, up to 40 50 % of R&D resources utilized. This research studies validation and verification as part of case company's component development process. The target is to define framework that can be used in improvement of the validation and verification capability evaluation and development in display module development projects. Validation and verification definition and background is studied in this research. Additionally, theories such as project management, system, organisational learning and causality is studied. Framework and key findings of this research are presented. Feedback system according of the framework is defined and implemented to the case company. This research is divided to the theory and empirical parts. Theory part is conducted in literature review. Empirical part is done in case study. Constructive methode and design research methode are used in this research A framework for capability evaluation and development was defined and developed as result of this research. Key findings of this study were that double loop learning approach with validation and verification V+ model enables defining a feedback reporting solution. Additional results, some minor changes in validation and verification process were proposed. There are a few concerns expressed on the results on validity and reliability of this study. The most important one was the selected research method and the selected model itself. The final state can be normative, the researcher may set study results before the actual study and in the initial state, the researcher may describe expectations for the study. Finally reliability of this study, and validity of this work are studied.

The state of research and development in Australia: implications for future development

The scale of research and development (R&D), and other technological activities, and the way in which the available resources are managed and organized at the enterprise and national level contribute to the rate of technological change in a country. A well organized national innovation system can be a powerful engine of progress, whereas a lack of interaction between institutions results in the slowing down of technological change, thereby diminishing its contribution to economic growth and welfare. The research object of this thesis is Australia’s national innovation system and the state of R&D in Australia. In order to establish an overall picture of the situation and to be able to make recommendations for future development, the general level of R&D activity and the main performers and funders of R&D within the system are analyzed. The framework policies supporting R&D and prevalent dynamics between different actors and sectors are of specific interest of the research. The findings reveal that the Australian culture is not a culture of research and innovation and that the main challenge is building a coherent system with strong domestic and international linkages.

Statistical Analysis and Numerics of Heat Exchanger Models

The identifiability of the parameters of a heat exchanger model without phase change was studied in this Master’s thesis using synthetically made data. A fast, two-step Markov chain Monte Carlo method (MCMC) was tested with a couple of case studies and a heat exchanger model. The two-step MCMC-method worked well and decreased the computation time compared to the traditional MCMC-method. The effect of measurement accuracy of certain control variables to the identifiability of parameters was also studied. The accuracy used did not seem to have a remarkable effect to the identifiability of parameters. The use of the posterior distribution of parameters in different heat exchanger geometries was studied. It would be computationally most efficient to use the same posterior distribution among different geometries in the optimisation of heat exchanger networks. According to the results, this was possible in the case when the frontal surface areas were the same among different geometries. In the other cases the same posterior distribution can be used for optimisation too, but that will give a wider predictive distribution as a result. For condensing surface heat exchangers the numerical stability of the simulation model was studied. As a result, a stable algorithm was developed.

Mobile technology, gender and development in Africa, India and Bangladesh

Presenting

Parallel-Operating Three-Phase Voltage Source Inverters – Circulating CurrentModeling, Analysis and Mitigation

The maximum realizable power throughput of power electronic converters may be limited or constrained by technical or economical considerations. One solution to this problemis to connect several power converter units in parallel. The parallel connection can be used to increase the current carrying capacity of the overall system beyond the ratings of individual power converter units. Thus, it is possible to use several lower-power converter units, produced in large quantities, as building blocks to construct high-power converters in a modular manner. High-power converters realized by using parallel connection are needed for example in multimegawatt wind power generation systems. Parallel connection of power converter units is also required in emerging applications such as photovoltaic and fuel cell power conversion. The parallel operation of power converter units is not, however, problem free. This is because parallel-operating units are subject to overcurrent stresses, which are caused by unequal load current sharing or currents that flow between the units. Commonly, the term ’circulatingcurrent’ is used to describe both the unequal load current sharing and the currents flowing between the units. Circulating currents, again, are caused by component tolerances and asynchronous operation of the parallel units. Parallel-operating units are also subject to stresses caused by unequal thermal stress distribution. Both of these problemscan, nevertheless, be handled with a proper circulating current control. To design an effective circulating current control system, we need information about circulating current dynamics. The dynamics of the circulating currents can be investigated by developing appropriate mathematical models. In this dissertation, circulating current models aredeveloped for two different types of parallel two-level three-phase inverter configurations. Themodels, which are developed for an arbitrary number of parallel units, provide a framework for analyzing circulating current generation mechanisms and developing circulating current control systems. In addition to developing circulating current models, modulation of parallel inverters is considered. It is illustrated that depending on the parallel inverter configuration and the modulation method applied, common-mode circulating currents may be excited as a consequence of the differential-mode circulating current control. To prevent the common-mode circulating currents that are caused by the modulation, a dual modulator method is introduced. The dual modulator basically consists of two independently operating modulators, the outputs of which eventually constitute the switching commands of the inverter. The two independently operating modulators are referred to as primary and secondary modulators. In its intended usage, the same voltage vector is fed to the primary modulators of each parallel unit, and the inputs of the secondary modulators are obtained from the circulating current controllers. To ensure that voltage commands obtained from the circulating current controllers are realizable, it must be guaranteed that the inverter is not driven into saturation by the primary modulator. The inverter saturation can be prevented by limiting the inputs of the primary and secondary modulators. Because of this, also a limitation algorithm is proposed. The operation of both the proposed dual modulator and the limitation algorithm is verified experimentally.

Analysis and Control of Excitation, Field Weakening and Stability in Direct Torque Controlled Electrically Excited Synchronous Motor Drives

Direct torque control (DTC) is a new control method for rotating field electrical machines. DTC controls directly the motor stator flux linkage with the stator voltage, and no stator current controllers are used. With the DTC method very good torque dynamics can be achieved. Until now, DTC has been applied to asynchronous motor drives. The purpose of this work is to analyse the applicability of DTC to electrically excited synchronous motor drives. Compared with asynchronous motor drives, electrically excited synchronous motor drives require an additional control for the rotor field current. The field current control is called excitation control in this study. The dependence of the static and dynamic performance of DTC synchronous motor drives on the excitation control has been analysed and a straightforward excitation control method has been developed and tested. In the field weakening range the stator flux linkage modulus must be reduced in order to keep the electro motive force of the synchronous motor smaller than the stator voltage and in order to maintain a sufficient voltage reserve. The dynamic performance of the DTC synchronous motor drive depends on the stator flux linkage modulus. Another important factor for the dynamic performance in the field weakening range is the excitation control. The field weakening analysis considers both dependencies. A modified excitation control method, which maximises the dynamic performance in the field weakening range, has been developed. In synchronous motor drives the load angle must be kept in a stabile working area in order to avoid loss of synchronism. The traditional vector control methods allow to adjust the load angle of the synchronous motor directly by the stator current control. In the DTC synchronous motor drive the load angle is not a directly controllable variable, but it is formed freely according to the motor’s electromagnetic state and load. The load angle can be limited indirectly by limiting the torque reference. This method is however parameter sensitive and requires a safety margin between the theoretical torque maximum and the actual torque limit. The DTC modulation principle allows however a direct load angle adjustment without any current control. In this work a direct load angle control method has been developed. The method keeps the drive stabile and allows the maximal utilisation of the drive without a safety margin in the torque limitation.

Mission and development : Finnish Pentecostal, Lutheran and Orthodox mission agencies in development work in Kenya 1948 - 1989

År 1974 började den finska regeringen kanalisera pengar för utvecklingssamarbete genom medborgarorganisationer. Tre år senare och fram till år 1988 beviljade regeringen ett speciellt anslag specifikt för missionsorganisationers utvecklingsprojekt. De finska pingstvännerna, lutheranerna och de ortodoxa utvidgade samtliga sitt sociala arbete i Kenya med statens stöd. Deras projekt var likadana: alla byggde läroanstalter, utvecklade Kenyas hälsoservice och sysselsatte kenyaner. Olikheterna mellan pingstvännerna, lutheranerna och de ortodoxa blev tydliga genom diverse problem som de mötte inom ramen för utvecklingssamarbetet. Den finska pingströrelsen bestod av självständiga församlingar, och pingstvännerna måste omvandla sin takorganisation, Suomen Vapaa Ulkolähetys, så att utvecklingsprojekt blev en viktig gren av dess verksamhet. Lutheranerna som till en början hade sänt missionärer för att arbeta i den kenyanska kyrkans tjänst började i medlet av 1970-talet i ökande grad bygga sociala anstalter med statens pengar. Ett problem var att statens stöd varade endast för en begränsad tid och att den lutherska kyrkan i Kenya inte hade råd att överta dessa anstalter och täcka deras löpande kostnader i framtiden. De finska ortodoxa, för sin del, igångsatte sociala projekt i samarbete med de ortodoxa i Kenya. Under några år fick de dock lära sig att de inte kunde driva självständiga utvecklingsprojekt i Patriarkens i Alexandria maktsfär. Den finska ortodoxa missionen blev tvungen att underkasta sig ärkebiskopen i Nairobi. År för år beviljade den finska regeringen större anslag för missionsorganisationernas utvecklingsprojekt och statens ansvar för kostnaderna ökade från 50% till 60% år 1984. Intressant nog mottog både lutheranerna och de ortodoxa mindre statliga pengar för utvecklingssamarbete år 1989 än 1984. Däremot växte pingstvännernas utvecklingssamarbete i Kenya under hela 1980-talet. Eftersom pingstvännerna inte ville använda sina medlemmarnas pengar (som var avsedda för missionsverksamhet) till sociala projekt täckte de sin andel i utvecklingskostnaderna med pengar från utanförstående. Pingstvännerna utvecklade en omfatttande komersiell och även industriell verksamhet för att samla in pengar för sina utvecklingsprojekt.

The analysis and mitigation of risks in FMCG supply chain: the case of British American Tobacco Eastern Europe

This work investigates the Bullwhip Effect, which is one of the most important phenomena in contemporary supply chain management. The author uses most recent theoretical apparatus to analyze operational activities of a leading FMCG company British American Tobacco Eastern Europe. This paper investigates and describes the process in BAT supply chain management and considers the impact of the Bullwhip Effect together with the potential risks threatening company's operations. Emergence of the Bullwhip Effect leads to supply chain inefficiency. This paper contains methodological supply chain risk mitigation recommendations, description of a real case study and an analytical study of internal and external supply chain processes

Design and development of the architecture of an agricultural mobile robot

Parameters such as tolerance, scale and agility utilized in data sampling for using in Precision Agriculture required an expressive number of researches and development of techniques and instruments for automation. It is highlighted the employment of methodologies in remote sensing used in coupled to a Geographic Information System (GIS), adapted or developed for agricultural use. Aiming this, the application of Agricultural Mobile Robots is a strong tendency, mainly in the European Union, the USA and Japan. In Brazil, researches are necessary for the development of robotics platforms, serving as a basis for semi-autonomous and autonomous navigation systems. The aim of this work is to describe the project of an experimental platform for data acquisition in field for the study of the spatial variability and development of agricultural robotics technologies to operate in agricultural environments. The proposal is based on a systematization of scientific work to choose the design parameters utilized for the construction of the model. The kinematic study of the mechanical structure was made by the virtual prototyping process, based on modeling and simulating of the tension applied in frame, using the.