Effect of moisture content on the physical properties of fibered flaxseed

The physical properties of fibered flaxseed were investigated within moisture content varying from 6.21 to 16.29%. The length, width, thickness and geometric mean diameter increased from 4.20 to 4.44mm, 1.99 to 2.13mm, 0.91 to 0.95mm, and 1.95 to 2.06mm, respectively in the moisture content range. One thousand seed weight increased linearly from 4.22 to 4.62g. The bulk density decreased from 726.783 to 611.872kg/m3, while the true density increased from 1165.265 to 1289.341kg/m3 in the moisture content range. The porosity values of flaxseed increased linearly from 37.67 to 52.54%. The highest static coefficient of friction was found on the plywood surface, while the lowest on the stainless steel surface. The static coefficient of friction increased from 0.467 to 0.972, 0.442 to 0.864, 0.492 to 0.927, and 0.490 to 0.845 for plywood, stainless steel, aluminum sheet and galvanized iron, respectively. The angle of repose increased linearly from 25.7° to 33.8° in the moisture content range. The results are necessary for design of equipment to handling, transportation, processing, and the storage of flaxseed.

Understanding in-vivo abrasion fatigue or common suture materials used in arthroscopic and open shoulder surgery

In orthopaedic surgery the reattachment of tendon to bone requires suture materials that have stable and durable properties to allow healing at the tendon-bone interface. Failure rates of this type of surgery can be as high as 25%. While the tissue suture interface is a weak link, proportions of these failures are caused by in-vivo abrasion of the suture with bone and suture anchor materials. Abrasion of the suture material results from the movement of the suture through the eyelet by the surgeon during surgery, or with limb movement after surgery as the suture is not rigidly restrained within the eyelet. During movement the suture is subjected to bending and frictional forces that can lead to fatigue induced failure. This paper investigates the mechanism of bending abrasion fatigue induced failure of number two grade braided sheath only and braided sheath/multifilament core sutures. Sutures were oscillated over a stainless steel wire at low frequency under load in a dry state to simulate the bending and frictional forces between suture and eyelet. Failure mechanism was determined by video microscopy of the suture during abrasion combined with optical microscopy analysis of partially and fully abraded sutures. Braided only structures had high friction loading on the small number of fibres at the abrasion interface. This caused rapid single fibre breakages that accumulate to cause suture failure. The addition of ultra-high molecular weight polyethylene core fibres to a braided suture distributed the applied load across multiple fibres at the abrasion interface. This improved abrasion resistance by 15-20 times that of braided sheath alone.

In vitro studying corrosion behaviour of biocorrodible Mg alloys

The idea of bioabsorbable/biocorrodible stents has gained increasing attention in the last decade. Permanent coronary stents, traditionally made from 316L grade stainless steel, are routinely used for the treatment of blocked arteries. However, these stents can cause complications such as restenosis, thrombosis and the need for the patient to undergo prolonged antiplatelet therapy. Biodegradable metal stents provide an opportunity for the stent to remain in place for a period to ensure restoration of function and then degrade through a carefully controlled bio-corrosion process. Among the number of potentially suitable materials, Magnesium alloys have shown great promise as a stent material due to their non-toxicity [1] and the corrosion rates attainable in biological environments. However, a carefully controlled corrosion process is essential in order to avoid hyper hydrogen generation and the fatal consequences that follow. In addition uniform corrosion is a basic requirement to maintain the mechanical integrity and load bearing characteristics. Work being undertaken in our laboratories focuses on controlling the corrosion behaviour of magnesium in a simulated biological environment in the presence of protein. In the investigation reported here the Mg alloy has been examined using Scanning Electrochemical Microscope (SECM) to visualize the corrosion process and identify the corrosion pattern. Complementary bulk electrochemical techniques (EIS and potentiodynamic polarization) have been used to acquire kinetic and mechanistic information. Early results obtained by SECM have revealed the tendency towards pitting corrosion in the early stages which subsequently develops in to filiform corrosion.

Effect of nanocrystalline structure on the corrosion of a Fe20Cr alloy

The corrosion behaviour of nanocrystalline and microcrystalline Fe20Cr alloys, prepared by high energy ball milling followed by compaction and sintering, was studied in 0.05M H2SO4 and 0.05M H2SO4 + 0.5M NaCl by potentiodynamic polarization. The nanocrystalline alloy exhibited improved passivating ability and pitting resistance as described by passivation potential, critical current density, passive current density and breakdown potential. XPS and SIMS analysis revealed greater Cr content in the passive film formed on the nanocrystalline form of the alloy. The enhanced passivating ability of the nanocrystalline alloy was attributed to the formation of the passive film with higher Cr content.

Recrystallization of 304SS during and after high strain rate deformation

During the hot working of austenitic stainless steels the shape of the flow curve is strongly influenced by the strain rate. Low strain rate deformation results in flow curves typical of dynamic recrystallization (DRX) but as the strain rate increases the shape changes to a ‘flat-top’ curve. This has traditionally been thought to indicate no DRX is taking place and that dynamic recovery (DRV) is the only operating softening mechanism. Examining the work-hardening behaviour and corresponding deformation microstructures showed this is not the case for austenitic stainless steel, as clear evidence of dynamic recrystallization process can be seen. The post-deformation recrystallization kinetics can be modelled using a standard Avrami equation with an Avrami exponent, n, of 1.15. With an increasing value of the Zener-Hollomon parameter it was found that the kinetics of recrystallization become less strain rate sensitive until at the highest values (highest strain rates/lowest temperatures) the recrystallization kinetics become strain rate insensitive.

Synthesis of high density boron nitride nanotube film

Antiwetting BNNT films have been achieved by milling-ink method. Superhydrophobic (CA <5°) are demonstrated on films with stainless steel as substrate. The high density and purity are confirmed by EDX and NEXAFS. There are only a few oxygen point defects in the form of nitrogen vacancies due to ink and annealing process in air.

Performance enhancement of single-walled nanotube-microwave exfoliated graphene oxide composite electrodes using a stacked electrode configuration

We report the development of a stacked electrode supercapacitor cell using stainless steel meshes as the current collectors and optimised single walled nanotubes (SWNT)-microwave exfoliated graphene oxide (mw rGO) composites as the electrode material. The introduction of mw rGO into a SWNT matrix creates an intertwined porous structure that enhances the electroactive surface area and capacitive performance due to the 3-D hierarchical structure that is formed. The composite structure was optimised by varying the weight ratio of the SWNTs and mw rGO. The best performing ratio was the 90% SWNT-10% mw rGO electrode which achieved a specific capacitance of 306 F g-1 (3 electrode measurement calculated at 20 mV s-1). The 90% SWNT-10% mw rGO was then fabricated into a stacked electrode configuration (SEC) which significantly enhanced the electrode performance per volume (1.43 mW h cm-3, & 6.25 W cm-3). Device testing showed excellent switching capability up to 10 A g-1, and very good stability over 10000 cycles at 1.0 A g-1 with 93% capacity retention. © the Partner Organisations 2014.

Investigation of hybrid ion-exchange membranes reinforced with non-woven metal meshes for electro-dialysis applications

Salt and solvent permeations across ion-exchange membranes used in electro-dialysis are directly related to the membrane material structure and chemistry. Although primarily used for aqueous effluents desalination, electro-dialysis was recently shown to be a promising technology for industrial wastewater and co-solvent mixtures purification. The harsh working conditions imposed by these liquid effluents, including high suspended solids, require the development of more chemically and mechanically resistant membranes. In this study, commercial porous stainless steel media filters (240. μm thick) were used as a backbone to prepare hybrid ion-exchange membranes by casting ion-exchange materials within the porous metal structure. The surface of the metal reinforcements was modified by plasma treatment prior to sol-gel silane grafting to improve the interface between the metal and the ion-exchange resins. The morphology of novel hybrid materials and the interface between the metal fibers and the ion-exchange material have been characterized using techniques such as scanning electron microscopy and FTIR mapping. The thickness of the silane coating was found to lie between 1 and 2. μm while water contact angle tests performed on membrane surfaces and corrosion test behaviors revealed the formation of a thin passivating oxide layer on the material surfaces providing anchoring for the silane grafting and adequate surface energy for the proper incorporation of the ion-exchange material. The hybrid membranes desalination performance were then tested in a bench top electro-dialysis cell over a range of flow rate, current densities and salt concentration conditions to evaluate the ability of the novel hybrid materials to desalinate model streams. The performance of the hybrid membranes were benchmarked and critically compared against commercially available membranes (Selemion™). Although the salt transfer kinetics across the hybrid ion-exchange composite membranes were shown to be comparable to that of the commercial membranes, the low porosity of the stainless steel reinforcements, around 60%, was shown to impede absolute salt permeations. The hybrid ion-exchange membranes were however found to be competitive at low current density and low flow velocity desalination conditions.

The need to revise the current methods to measure and assess static recrystallization behavior

Heterogeneous deformation developed during "static recrystallization (SRX) tests" poses serious questions about the validity of the conventional methods to measure softening fraction. The challenges to measure SRX and verify a proposed kinetic model of SRX are discussed and a least square technique is utilized to quantify the error in a proposed SRX kinetic model. This technique relies on an existing computational-experimental multi-layer formulation to account for the heterogeneity during the post interruption hot torsion deformation. The kinetics of static recrystallization for a type 304 austenitic stainless steel deformed at 900 °C and strain rate of 0.01s^-1 is characterized implementing the formulation. Minimizing the error between the measured and calculated torque-twist data, the parameters of the kinetic model and the flow behavior during the second hit are evaluated and compared with those obtained based on a conventional technique. Typical static recrystallization distributions in the test sample will be presented. It has been found that the major differences between the conventional and the presented technique results are due to the heterogeneous recrystallization in the cylindrical core of the specimen where the material is still partially recrystallized at the onset of the second hit deformation. For the investigated experimental conditions, the core is confined in the first two-thirds of the gauge radius, when the holding time is shorter than 50 s and the maximum pre-strain is about 0.5.

Unlawful acts, unkind architecture and unhelpful perceptions: a case study of Market Square Mall, Geelong

On a quiet Sunday afternoon in January 2015, a 12 year old girl was assaulted in Geelong’s Market Square mall. The attack sparked a media furore over what should be done to address the ongoing safety and amenity issues of this intractable public space. The city’s mayor, Cr Darryn Lyons, responded to the situation by declaring the mall a ‘haunt for bogans and scumbags’ and renewed calls for its demolition. Such rhetoric highlights the exclusionary mindset that casts certain types of people as undesirable inhabitants of public spaces. It also bolsters negative public perceptions of the mall. Once formed, such attitudes are difficult to shift, despite an overall improvement in the area’s crime rates over recent years. Poor perceptions are further reinforced by the soulless nature of the mall’s built fabric and weak urban interfaces. Its formal language is one of hostility, not only towards would-be delinquents, but to all people. The space is furnished with cold stainless steel seats, CCTV cameras and limp, pavement water spouts, while its inactive edges consist of loading bays, security grilles and neglected facades. This paper considers how a more inclusive architecture might be utilised to create a kinder, more generous physical environment that reflects the public nature of the space. While not a quick fix, fostering an architecture that encourages a more equitable use of the mall may diminish the sense of fear, anxiety and suspicion that the space currently elicits, tackling the problem at both a structural and social level.

Effect of δ-ferrite co-existence on hot deformation and recrystallization of austenite

This work evaluates the effect of co-existence of a large volume fraction of δ-ferrite on the hot deformation and dynamic recrystallization (DRX) of austenite using comparative hot torsion tests on AISI 304 austenitic and 2205 duplex stainless steels. The comparison was performed under similar deformation conditions (i.e. temperature and strain rate) and also under similar Zener-Hollomon, Z, values. The torsion data were combined with electron backscatter diffraction (EBSD) analysis to study the microstructure development. The results imply a considerable difference between DRX mechanisms, austenite grain sizes and also DRX kinetics of two steels. Whereas austenitic stainless steel shows the start of DRX at very low strains and then development of that microstructure based on the necklace structure, the DRX phenomena in the austenite phase of duplex structure does not proceed to a very high fraction. Also, the DRX kinetics in the austenitic steel are much higher than the austenite phase of the duplex steel. The results suggest that at a similar deformation condition the DRX grain size of austenitic steel is almost three times larger than the DRX grains of austenite phase in duplex steel. Similarly, the ratio of DRX grain size in the austenitic to the duplex structure at the same Z values is about 1.5.

Análise morfométrica digital na parede aórtica de suínos após implante de stents não revestidos versus stents revestidos com dacron

Os stents são dispositivos intravasculares implantados com o objetivo de dilatar ou fixar a placa de colesterol contra a parede arterial. O objetivo avaliar dois tipos de stents de aço inoxidável, um recoberto com poliéster (dacron) e outro não recoberto, implantados na aorta infra-renal de suínos jovens, foram avaliados por morfometria digital para medir o espessamento intimal. Foi realizado um estudo experimental randomizado, separados em dois grupos(stents não revestidos e revestidos com dacron) e duas fases (I e II). Oito stents recobertos com dacron e oito stents de aço inoxidável (30mm de extensão e 8 mm de diâmetro), não revestidos, foram implantados através de abordagem retroperitoneal na aorta infrarenal normal de 16 suínos normolipêmicos. Para a passagem do sistema de implante, foi necessário uma pequena arteriotomia na aorta distal (fase I). Após quatro semanas, a aorta com os stents foram removidas em monoblocos (fase II). Os valores de hematimetria e do lipidograma foram coletados nas duas fases e não apresentaram alterações que pudessem influenciar o estudo. Amostras de tecido dos sítios de fixação (proximal e distal) dos stents foram retiradas, confeccionadas lâminas, que foram coradas pelas técnicas de hematoxilina e eosina de Verhoeff e enviadas para análise morfométrica digital. A camada intima distal não apresentou diferença estatística significativa. A camada média proximal das porções proximal e da porção distal não apresentaram diferença entre os grupos. Os dois tipos de stents apresentaram 100% de perviedade, boa biocompatibilidade e boa incorporação a parede aórtica de suínos normolipêmicos. A camada íntima proximal do grupo de stents revestidos com dacron apresentou espessura maior do que os stents não revestidos, mas com significância estatísitica limítrofe.

Comportamento do aco inoxidavel ABNT 304 a corrosao-sob-tensao em solucoes aquosas neutras de nacl a temperatura de ebulicao utilizando a tecnica de carga constante

Estudou-se o comportamento do aço inoxidável ABNT 304 à corrosão-sob-tensão (C.S.T.) em soluções aquosas com 0,1%, 3,5% e 20% de NaCl, na temperatura de 103°C, através de ensaios de carga constante. Com auxílio das técnicas e conceitos de Mecânica de Fratura Linear Elástica e das análises eletroquímicas procurou-se encontrar as condições em que ocorre C.S.T. no sistema aço inoxidável austenítico/solução aquosa de NaCl a 103°C. Utilizou-se o corpo-de-prova do tipo dupla viga em balanço (T-notch double cantilever beam: TN-DCB), com intuito de observar a influência do fator de intensidade de tensão, concentração da solução e potencial eletroquímico. Estimou-se o valor do fator de intensidade de tensão limite (KICST) e a velocidade de propagação das trincas; também foram analisadas outras importantes características em termos mecanísticos. Definiu-se faixas de potenciais e valores de intensidade de tensão a partir dos quais ocorre o surgimento de trincas por C.S.T.. Fêz-se análises metalográficas dos corpos-de-prova onde se pode constatar trincas transgranulares bem típicas do fenômeno de C.S.T.. Foram feitos alguns testes em solução aquosa saturada de MgCl2, em ebulição, para se comparar as diferentes soluções quanto ao fenômeno de C.S.T.. Alterou-se as dimensões do corpo-de-prova para avaliar a orientação da propagação das trincas por C.S.T..

Nitretação a plasma do aço ABNT 316L em baixas temperaturas

A nitretação dos aços inoxidáveis austeníticos apresenta grande interesse tecnológico, pois tanto em processos convencionais tais como as nitretações a gás e em banho de sais como em processos a plasma, obtêm-se um aumento significativo de sua dureza superficial e resistência ao desgaste. No entanto, devido as altas temperaturas utilizadas nos processos convencionais, observa-se uma extensa formação de precipitados de nitretos de cromo, com consequente redução de resistência à corrosão do material. A proposta deste trabalho é utilizar a tecnologia de plasma para nitretar um aço inoxidável austenítico neste caso o ABNT 316 L a temperaturas relativamente baixas a fim de evitar precipitação de nitretos). As temperaturas utilizadas foram de 350, 375 e 400 0C, variandose o tempo de nitretação de 3 ,4 e 5 horas com duas misturas gasosas (76%N2 e 24%H2 e 5%H2 e 95%N2). As amostras foram analisadas através da microdureza superficial (método convencional e nanodureza), caracterização microestrutural por microscopia ótica, eletrônica de varredura e de transmissão, medida da profundidade de camadas formadas (MEV), rugosidade, determinação das fases presentes (Raios - X), nanodureza , perfil da composição química (GDOS) e resistência à corrosão (névoa salina e curvas de polarização) As amostras nitretadas nestas temperaturas e tempos produziram camadas de 1,9 a 5,5 µm medidas via GDOS e durezas que vão de 330HK a 987HK não observando-se a precipitação de nitretos de cromo, mas sim a formação de uma estrutura supersaturada de nitrogênio intersticial, chamada de “fase S” identificada por difração de Raios - X. As camadas nitretadas apresentaram um gradiente de nitrogênio que diminui, indicando um gradiente junto as características microestruturais, níveis de tensões residuais favoráveis para uma boa adesão, com a formação de uma camada com menor fragilidade. Esta fase “S”, além de produzir altas durezas superficiais, aumentou a resistência à corrosão do aço. Testes em campo com navalhas de corte e facas móveis tiveram um aumento de vida útil de 100% e 217%.